Search Documents

By Xi-Shan Li, Qian Li, Yong-bin Yang, Li-na Cui, Tao Jiang, Jie Ge

"With regard to control environment pollution in the roasting pretreatment of sulfur & arsenic-bearing gold concentrate, roasting of double-layered pellet was proposed. In the paper, the characteristics of double-layered pellet roasting were studied. Removal and solidification rates of sulfur and arsenic were investigated as primary factors. The result indicated that the removal and solidification rates of arsenic reached up to 95.91 % and 98.95% while the sulfur was 97.19% and 97.90% respectively on the premise of adopting slaked lime as solidified agent at temperature of 6000, the package proportion of 2.14 and roasting time of 3h. However, pyrite and arsenopyrite were transformed to hematite and magnetite and product of solidification mainly consisted of calcium sulfate, calcium arsenate and calcium sulfite within optimum roasting parameters.IntroductionUtilization of refractory gold resources has been gradually concentrated on with the depletion of the gold resources which are easy to deal with in the world [1]. Sulfur and arsenic-bearing gold ore is a typical refractory gold one, in which ultrafme gold is encapsulated in the structure of metal sulfide minerals [2,3], so it gives poor recovery through direct cyanide leaching. These refractory ores need pretreatment before the process of cyanide leaching to undermine lattice structure of pyrite and arsenopyrite containing gold [4] so that the gold could touch with cyanide solution [5]. Among various methods of pretreatment, conventional roasting method is most effective, but this process generates gases such as S02 and As203 harmful to environment. Therefore solidification roasting was proposed to solve this problem occurring in the conventional roasting at the end of last century."

Jan 1, 2013

By William H. Bassett

COPPER is the world's most important non-ferrous metal, and brass is the most widely used non- ferrous alloy. Much of the utility of each may be credited to the work of metallurgists who have constantly improved the quality of the metals and alloys and the methods of fabrication. Standing in the front rank among these is William Hastings Bassett, the newly elected president of the Institute. Mr. Bassett, ,who is technical superintendent and metallurgist for the American Brass Co.,

Jan 1, 1930

By H. Gurgenli

Mining companies require accurate short-term mining forecasts to meet budget targets and customer needs. Challenging mining conditions along with employee turnover and lack of standard geologic modeling and mine planning processes can result in time-consuming and inconsistent mine plans. Documentation and automation of the processes involved in mine planning, as well as proper software utilization, are critical in overcoming these challenges. This paper discusses the steps involved in achieving an optimized mine planning system to accomplish productive and cost effective operations. In addition, a case study is included to describe the process of implementing a semi-automated system whereby the geologic model and mine scheduling database are updated monthly to incorporate changes in geology in a relatively complex open-pit coal mine. This case study proves that the ability to update geologic models based on the latest information gathered from production drilling and mining activities can greatly enhance the ability to accurately predict short-term mining production.

Jan 1, 2011

By W. M. Scheding

"There has recently been a resurgence of interest in unit flotation of mill discharges. At the Kidd Creek concentrator, this technique has been successfully applied to silver flotation in a 3050 mtpd silver-copper-lead-zinc division. The major incentive has been improved silver payment through increased overall recovery and better distribution between the sequential copper, lead and zinc concentrates. A large, but variable fraction of the silver in the ore is present as native silver and, being dense and malleable, is susceptible to overgrinding. Grinding circuit surveys showed high concentrations of silver in both primary and secondary circulating loads. Laboratory testwork confirmed that this was selectively flotable, identified the secondary ball mill discharge as the best feed stream and optimized flotation conditions. A 10 t/h pilot plant campaign confirmed that the rate of accumulation of silver was sufficient to sustain continuous production of a silver concentrate and that flotation of the whole stream was not necessary.The present 30 t/h production circuit recovers from 5 to 50% of the silver in the ore at a concentration ratio between 25 and 250. The circuit also contributes to a better understanding of ore mineralogy, as an 'on-line' indicator of elemental silver content."

Jan 1, 1985

[Early in 1936 the Interstate Oil Compact Commission and other groups interested in forecasts of demand .for petroleum requested the Bureau of Mines to make a physical inventory of crude-oil stocks in the United States. Accordingly, the 74th Congress appropriated funds for conducting such a survey during the fiscal year ended June 30, 1937. In the discussions and hearing2/ relative to the need for the sway, the opinion ms expressed that crude oil held in storage for long periods had lost so much of its gasoline content that he economic significant of total stocks should be discounted materially. Therefore, a primary objective of the survey was to]

Jan 1, 1938

By J. A. Ruppert, P. M. Sullivan

A process was developed on a laboratory scale in which iron contained in galvanizers ' zinc dross and aluminum contained in scrap zinc die - cast alloy were removed simultaneously . Melting both types of scrap together in the proper proportions resulted in formation of solid intermetallic Fe₂ Alg , which was readily removed from the melt by filtration and centrifugation . Recovery was 87 to 92 percent of the available zinc . Refined filtrate contained 0.02 percent iron and 0.20 percent aluminum. Aluminum content was further reduced to less than 0.01 percent by fluxing with zinc chloride . Low temperatures employed and inexpensive equipment requirements make the process commercially attractive .

Jan 1, 1964

Interest in those physical properties of minerals which might be used to good effect in prospecting is not new. Early in the nineteenth century attempts were made in th'e Cornish mines to measure the natural electric potentials set up by chemical changes proceeding in the lodes. The distortion of the earth's magnetic field by bodies of strongly magnetic iron ore received early recognition in Sweden. Treasure-finders, working on the principle of electrical induction, appear to have been invented about eighty years ago, though were probably not then applied to mineral exploration. By the end of the nineteenth century Eotvos, a Hungarian physicist, had constructed a highly sensitive type of torsion balance capable of measuring the minute distortions in the earth's field of gravitation resulting from variations in the density of the materials composing the crust. During the first decade of this century he demonstrated its value in tracing rock-salt deposits in virtue of their low density compared with the surrounding rocks. Geophysical prospecting began to be recognised as having a very definite value and its development gathered momentum. Its great expansion took place after the 1914-18 war, when its value in oil exploration was amply demonstrated, and this expansion has continued to the present time and shows no signs of abating.Divisions of Applied Geophysics.The four main divisions of applied geophysics are electrical, magnetic gravitational and seismic. With the importance of ores of radio-active metals, one might add to these a radio-active division. The first two are more important to the field of mining, but techniques based on gravitational attraction have their uses in particular cases. Seismic methods are not generally suited to the exploration of metallic ores, but have proved of enormous value in the search for petroleum. With vast quantities of oil as the prize, more money has been lavished on the deve10pment and practice of these methods than on all the others put together.Geophysical Prospecting Methods.Geophysical prospecting methods may be used to detect a mineral deposit directly in virtue of differences in the intensity of some physical attribute common to it and the enclosing country rock. Examples of this are the detection of rock-salt by gravity measurements, or of iron ore by magnetic methods. Of much wider application, however, is the indireot approach in which the aim is to determine, by geophysical means, the geological structures controlling the disposition of mineral deposits. These structures may be partly known from geological work, in which case geophysical methods are useful adjuncts. Where, because of an 'unbroken cover of overburden, no useful geological information presents itself, scout drilling or geophysical prospecting are the only alternatives. Overburden is here intended to mean any covering material not, involved in the structures controlling the mineral deposits. Prospecting for petroleum amounts to the detecting of favourable reservoir structures, and as the chief types of such are the same the world over...

Jan 1, 1950

By Hindmarsh J. W, McCoy A. E R

Instantaneous outbursts of coal and gas have occurred at various times in several working districts of Metropolitan Colliery, N.S.W.They have occurred in headings only, under both hand and mechanised conditions, and with seam gas ranging from mainly methane to nearly pure carbon dioxide. A modification of inducer shotfiring using a shear cut was introduced in 1955, and in 1961 full face firing both to a machine cut shear and off the solid was introduced. The current series of outbursts -1961 to 1963 - has been induced under these systems with full control of the time of outburst, but without prediction, and with some disappointing production features.Various aspects of current conditions and practices at Metropolitan are considered singular, such as the coarse granulometry of outburst coal, the prevalence of floor heave, the absence of strong structures at outburst sites, the possibility of outburst at any stage in pillar formation up to the last few yards, the effect of rate of advance on outburst occurrence, and the mildness of many outbursts experienced.It is concluded that inducer shotfiring is a reliable control but it suffers by comparison with outburst-free conditions, and that control by preyention would be preferable.INTRODUCTIONThe phenomenon of instantaneous outbursts of coal and gas has been described in detail previously (Hargraves, 1958). Briefly, it is a combined gas and stress hazard of deep coal mining, usually occurring in virgin work and during active face advance, when coal and seam gas burst from the face into the workings.Instantaneous outbursts have occurred sporadically at Metropolitan Colliery, N.S.W., since 1895. Early outbursts were recorded as firedamp and recent outbursts are of blackdamp.Mining methods used have been conventional hand work, with progressive and relatively complete mechanisation over the past 25 years to substantially conventional...

Jan 1, 1964

By W. F. Chiao

Ultrasonic attenuation, a, measurements in the frequency range of 5 to 55 mc per sec have been studied to determine their quantitative relationship with the following three variables of mixed microstructures in steels: 1) the volume percent, XF, of polygonal fer-rite in mixed structures of martensite and polygonal ferrite in Fe-Mo-B alloys: 2) volume percent, XA, of retained austenite plus martensite aggregates in high-carbon steel; and 3) substructural differences between 100 pct bainitic ferrite structures formed at various temperatures. The quantitative relationship obtained in the first two conditions by plotting a us the known structural parameters can be expressed, respectively, as: where al, a 2 and C1, Cz are constants. In the third condition the nature of the attenuation depends on the state of dislocations generated at the transformation temperatures and also on the alloy composition. From these measured results, the mechanism of ultrasonic attenuation caused by these mixed microstructures can also be studied. MUCH interest has recently been shown in the application of ultrasonic attenuation and wave velocity measurements to the study of the microstructural characteristics of steels. The general aims of most of the investigations in this field can be grouped into two categories: one is to study the mechanisms of ultrasonic losses caused by the characteristic phases in the microstructure of steel,''' and the other is to develop nondestructive test methods and applications for quality control.~' 4 Apparently no work has been done on the evaluation of ultrasonic attenuation meas -urements as a means of quantitative determination of a given phase in the microstructure of a steel. It is well-established that the decomposition of austenite results in four main microstructural constituents—polygonal ferrite, pearlite, bainite, and martensite—and that each phase has different mechanical properties. Thus, when a steel consists of mixed microstructures, the mechanical properties can often be related to a quantitative measure of the volume percent of each phase present. This study relates ultrasonic attenuation measurements to: 1) the volume percent of polygonal ferrite in mixtures of martensite and polygonal ferrite in Fe-Mo-B alloys; 2) the substructural differences between 100 pct bainitic ferrite structures formed at various temperatures; and 3) the vol- ume percent of austenite in austenite plus martensite aggregates in a high-carbon steel. The choice of the specimen materials was based on the laboratory stocks which were suitable to produce the required mixed microstructures for this study. EXPERIMENTAL PROCEDURES Materials and Heat Treatment. Polygonal Ferrite Plus Martensite Structures. This mixture of phases was produced in a vacuum-melted Fe-Mo-B alloy. The alloy was hammer-forged at 1900" ~ to a -f-in.-sq bar. By isothermally heat treating the alloy at 1300° F for various times and then water quenching, variations in the amount of polygonal (or proeutectoid) ferrite can be controlled in a microstructure in which the balance of the material is martensite. In the present work, four different times of isothermal transformation were adopted; after heat treatment, the four specimens were machined for ultrasonic measurements. The compositions, heat treatments, and dimensions of the four specimens are listed in Table I. 100 pct Bainite Structures Formed at Different Temperatures. It has been well-established by Irvine et al.= that the presence of molybdenum and boron in ferrous alloys can retard the formation of polygonal proeutectoid ferrite and expose the bainitic transformation bay, so that a more acicular or bainitic ferrite can be obtained over a wide range of cooling rates. Their investigation6 also showed that the mechanical properties of fully bainitic steels are usually closely dependent on the substructural characteristics of the steels. For studying the substructural characteristics in completely bainitic structures, six Fe-Ni-Mo alloys, of which five were free from carbon addition and one with 0.055 pct C addition, were selected so that a wide range of hardness values for 100 pct bainitic ferrite structures could be produced by normalizing at 1900" F followed by air cooling. The different bainitic transformation temperatures were recorded during air cooling. All of the alloys were vacuum-melted and then forged at 1900" F to square bars. Data on the six specimens of these structure series are summarized in Table 11. Austenite Plus Martensite Structures. The high-carbon steel used to study austenite plus martensite structures was vacuum-melted and then forged into Q-in.-sq bar. The series of mixed structures of austenite plus martensite was produced by quenching the specimens from the austenitizing temperature to room temperature and then refrigerating them at various temperatures within the range of martensite transformation to produce different amounts of retained austenite. Data on the four specimens of this series are listed in Table 111. Quantitative Analysis of the Microstructures. The microstructures containing martensite plus polygonal ferrite were analyzed by the point-counting technique.

Jan 1, 1969

By W. Rubarth

The kaolin losses in hydrocyclone classification are determined by the fines, which are discharged together with the water to the underflow. This paper presents an improved technique of water injection to the conical part of the cyclone applied especially for small cyclones in kaolin preparation. In small hydrocyclones water, injection is a sensitive process. Therefore, the process was stabilized by controlled water injection dependent on the measurement of the underflow shape. Three applications of this innovation are presented. In the first case, the water injection is applied for the separation stage in dilute suspension where the final product is produced in the overflow of a 50mm hydrocyclone. The underflow contains sand and residual kaolin. For a higher kaolin recovery, the underflow is usually treated downstream in washing cyclones. The wash water injection results in a 45 ? 50% - reduction of the kaolin fraction <25µm in the underflow. Thus, water injection to the classifying cyclone leads to a separation comparable with a downstream washing stage. An additional hydrocyclone stage can be deleted. The second application refers to a classification in dense suspension. Here, the underflow of the last hydrocyclone stage was directed to a washing in a 50mm hydrocyclone. The additional injection of 3L/min water in to the conical part of the cyclone reduced the kaolin losses by half.The third application was executed in the washing stage equipped with 75mm hydrocyclones where the underflow is directed to flotation. Using the water injection the kaolin recovery in this stage was increased by approximately 20%. Keywords: hydrocyclone, classification, kaolin beneficiation, water injection, underflow washing

Sep 1, 2012

The zinc-lead lode at Rosebery, on the West coast of Tasmania, has a total length of over 4000 ft. It consists of five elongated lenses parallel to the foliation planes of the quartz sericite schist, and is situated at the junction of the quartz sericite schist and a thin belt of slate. The lenses consist of massive, fine grained sulphide ore, with small amounts of quartz, barite, sericite and chlorite, and they terminate in masses of low grade ore. The gangue minerals increase in quantity in the low grade ore which includes small quantities of the manganese garnet, spessartite. The schist walls of the lenses are in places impregnated with lode minerals to a degree sufficient to permit them to be regarded as economic ore.The ore-bodies have developed from incoming mineral solutions by the replacement of the quartz sericite schist and are localised where the ore solutions have been confined by a relatively impervious slate band. The early stages of replacement of the schists are signified by the development of pyritic bands which are succeeded by a strong development of zinc blende. With ptogressive crystallisation, the character of the mineral solutions gradually changed and the development of galena, and its associated bournonite, became more important in the later stages.Remnants of the replaced schist, in the form of isolated wisps and schlieren of sericite and chlorite, are present in the ore body, more noticeably in the pyritic specimens. An important feature of the ore is the association of small ogllantities of gold with trahedrite.

Jan 1, 1934

By N. F. Schulz, H. A. Lex, J. D. Zetterstrom

A green ball of iron ore faces many perils from the time it is formed until it finally emerges from the pelletizing furnace as a hardened pellet. For instance, if the rate of heat transfer into a ball is sufficient to produce vapor from either the free or combined water more rapidly than it can escape at a tolerable pressure, the ball may split, spall, or even explode, a failure commonly known as decrepitation. To avoid such failures, one must either limit the rate of heat transfer during the drying and preheating stages, at the expense of production rates, or improve the decrepitation resistance of the green balls. The latter remedy may often be accomplished through changes in ore preparation, balling procedures, or the judicious use of binders or other additives. INTRODUCTION Pelletization has become established as an especially desirable method for the agglomeration of fine taconite concentrates and it promises to be equally satisfactory for improving the physical structures of certain natural ores. A high-quality pelletized iron ore consists of uniformly sized spheres, usually about 1/2-in. diam, which are strong enough to resist abrasion and breakage during handling and which reduce well without disintegration in the blast furnace. The unfired agglomerates, "green balls", are subject to several destructive effects that must be avoided or minimized if a high-quality product is to be obtained by pelletization. Among these are abrasion and impact deformation or breakage during handling of the wet green balls, deformation and breakage by compressive forces in the bed of ore in the pel-letizing furnace, decrepitation during drying and preheating, wind erosion, and radial cracking at firing temperatures. Moisture condensation from the warm saturated gases downstream from the drying zone on wet, cool balls may cause bed collapse if it becomes excessive. Decrepitation is defined as the sudden disintegration of green balls, usually with an audible pop, that occurs when they are heated too rapidly during the drying or preheating stages of the pelletization process. The extent of ball disintegration may vary from merely splitting off a small fragment to almost total disintegration into the original ore particles making up the ball. Such ball destruction results in a decreased yield of pellets, and the fragments, which also tend to interfere by obstructing the gas flow through the bed, must eventually be screened from the fired product and recycled. The closely related type of ball failure that sometimes occurs during the high temperature firing stage, resulting in radial cracks without fragmentation, was not considered to be decrepitation for the purpose of this investigation. Failure by decrepitation is not usually a serious problem in the pelletization of taconite concentrates. The problem is significant, however, in the pelletization of some natural ores, especially those containing hydrous iron oxides. In some instances, economicd production rates cannot be maintained if the drying and preheating rates are slowed down enough to avoid decrepitation. OBJECTIVES This investigation was undertaken to: (1) Develop a practical laboratory means for quantitatively measuring the tendency for green balls to decrepitate in iron ore pelletizing furnaces, and (2) Investigate the causes and cures of ball decrepitation. MATERIALS Two iron ores were used in the work reported here: a taconite concentrate at 90% minus 325 mesh, containing 65.0% Fe, 8.4% SiO2, and no loss-on-ignition; and a crude oxidized ore at 54% minus 325 mesh, containing 59.1% Fe, 3.6% SiO2, 1.1% A12O3, and 9.5% loss-on-ignition. For a special test of effect of particle size distribution on decrepitation, two other

Jan 1, 1967

By K. F. G. Hosking

I read Professor Gaudin&apos;s paper with great interest and pleasure because for some time I have held that the chemical aspect of comminution is a subject of considerable importance to the mineral dresser and deserves to be thoroughly investigated. It does seem appropriate, however, to emphasize the fact that "fresh" edges and corners produced by the grinding of solids display enhanced reactivity has been recognized and utilized in the development of certain mineral identification techniques. Some of these techniques are worth noting, not only because they might facilitate research in the aspect of mineral dressing under discussion, but also because they emphasize the fact that many mineral species commonly regarded as being very inert can display a surprising reactivity when in the freshly ground state. In 1951 Isakov6 published a number of tests for the components of certain mineral species which depend essentially on grinding in a mortar a mixture of the material under investigation with a solid reagent. Thus when stibnite, 4(Sb2S3), is ground with sodium or potassium hydroxide. the antimony is revealed by a momentary development of a yellow color which changes in air to orange-red. Other antimony minerals need a preliminary treatment before the test can be carried out. This consists of grinding with aluminium sulfate, ferric sulfate or potassium bisulfate, and breathing upon the resultant mixture. I have employed a similar technique to determine the approximate magnesia content of certain limestones.&apos; The method depends essentially on the fact that when a sample of limestone is ground under controlled conditions with solutions of sodium hydroxide and Titan yellow the color of the final product is, within limits, a function of the amount of magnesia present. I have also shown that the components of a wide range of minerals can be identified by applying chemicals to their streaks on portions of vitrified, unglazed floor tiles, etc. Under such circumstances the diversity of the reactions which take place in the cold (because of the reactivity of fresh corners and edges) is surprising. Thus, for example, if a garnierite, (Ni,Mg)3Si2O5(OH)1, streak is treated first with a drop of 0.880 ammonia and then with a drop of a 1 pct alcoholic dimethyl-glyoxime it immediately becomes red, indicating the presence of nickel.&apos; Stevens and Carron9 have evolved a simple field test for distinguishing minerals by "abrasion pH." A soft nonabsorbent mineral is scratched in a drop of water on a streak plate until a milky suspension is formed. A piece of pH indicator paper is dipped into the suspension, after which it is removed and the maximum deviation from neutrality noted. When a hard mineral or one which absorbs water is being tested, fragments are first ground for 1 min with a few drops of water in a mortar to make a heavy suspension. The importance of the findings of such tests to mineral dressing may be judged by the abrasion pH values, Table 11, recorded by Stevens and Carron for certain species usually regarded as comparatively inert. The combined results Of the above researches clearly indicate that comminution is capable of altering the pH of a pulp and of causing the chemical nature of the surfaces of some of the components to be profoundly changed&apos; Depending On circumstances such surface alterations may have a beneficial or an adverse effect if these products are subsequently subjected to flotation. The tests also suggest that by grinding "inert" minerals with appropriate solid or liquid reagents "reactive" surfaces may be developed which might facilitate separations by flotation. It is an interesting and instructive problem to determine the reactions that are likely to take place when dry solid substances are subjected to comminution and to the unavoidable heat liberated during the process. To do this it is theoretically necessary to know the free energy values of the reactants and possible resultants, but unfortunately there is a dearth of such data! However, the heats of formation of many substances are known, and generally speaking, if in a reaction of the type AB + CD = AD + CB the sum of the heats of formation of AB and CD is less than that of AD and CB the reaction will probably proceed to the right. Thus, according to a note I have (the author of which I cannot name) if PbS (black) is warmed with CdSO, (white), PbSO., (white) and CdS (yellow) are formed, and that the reaction does, in fact, take place is indicated by the change in color of the mixture. The reaction is expected, as the sum of the heats of formation of PbS and CdSO, is less than that of PbSO, and CdS (as shown below). PbS + CdSO4 = PbSO4 + CdS 22.2 + 218.0 < 216.2 + 33.9 Finally, certain other aspects of the chemistry of comminution, which are neither mentioned by Professor Gaudin nor referred to by me are to be found in a paper by Welsh" and in the printed discussion thereof. A. M. Gaudin (author&apos;s reply)—The observations contributed by Dr. Hosking are indeed welcome, as they add to our experimental knowledge of a topic which is believed to be of the first importance. In connection with the experiments cited it should be kept in mind that oxidation, hydration, and carbonation at various rates should always be deemed to be possibilities when grinding is done in water or in air, even in "industrially dry" air. Special precautions might lead to sufficient minimizing of these reactions and to the assertion, instead, of deliberately-created reactions. The author wishes to thank Dr. Hosking for his contribution.

Jan 1, 1957

By A. G. Doll

"Multi-stage crushing plants, including high pressure grinding roll (HPGR) circuits, require more materials handling equipment than SAG and ball mill circuits. A temptation exists to neglect the energy consumption of materials handling when doing desktop comparisons of HPGR versus SAG milling circuits because estimation of materials handling power requirements can demand significant general arrangement drafting that is not available when performing preliminary scoping or ""desktop"" studies.The largest component of materials handling power is consumed by conveyors when lifting material between stages of crushing, meaning that a simple potential energy model can be used to evaluate conveying specific power consumption. This potential energy consumption for conveying can then be factored to provide overall materials handling specific energy consumption suitable for desktop studies of HPGR and other multi-stage crushing circuits. The technique also permits different crushing circuit flowsheets to be evaluated, at a preliminary level, by simply counting the number of times a conveyor must ""lift"" ore from ground level up to a bin or other equipment mounted up high.INTRODUCTIONTrade-off studies of multi-stage crushing plants involving high pressure grinding rolls (HPGRs) versus semi-autogenous grinding (SAG) mill circuits typically focus on the operating cost savings of crushing plants versus the capital cost savings of SAG mill plants. Very high-level (or desktop) studies of this type do not include a great deal of engineering work, meaning that the details (and costs) of ancillary systems are often not captured when doing the comparisons. The more complicated nature of the multistage crushing plants means there are more ancillary systems than a SAG mill plant, risking a skewed analysis of the operating costs, benefiting the HPGR option.One of the ancillary systems that may be overlooked is the more complicated conveying systems inherent in multi-stage crushing plants. Due to the mass of material being handled in large mining operations, these conveyors become a significant portion of the operating costs. A simple way to estimate the specific energy consumption of conveying systems without requiring engineering drawings and a site layout would allow high-level studies to capture this operating cost."

Jan 1, 2015

By William P. Shinn

IT seems proper to present in the Transactions of the Institute, from time to time, formal record of the advances made in the arts and sciences to which our organization is devoted-milestones in the highway of progress-from which our successors may measure what they in their turn have gained. The admirable address of the Hon. Abram S. Hewitt, then president elect of the Institute, on "A Century of Mining and Metallurgy in the United States," read at the opening of the meeting held in this hall in June, 1876, forms a point of departure, and the conclusion of the eighth decade of the nineteenth century and the end of the first five years of our country&apos;s second century seem to offer a fitting time for again making up our record. The period since 1875 has been marked by a degree of activity in mining and metallurgical industry never before equalled in our history, while the progress made in the science and art has been, if possible, still more noticeable. Whether we consider the mining of iron, ore, and coal, or of the precious metals,-the advances made in smelting the former and in reducing the latter, the extraordinary increase in the production of Bessemer steel, or the science of Thomas and. Gilchrist, which makes the hitherto rejected phosphorus the corner-stone of success,-the past five years are alike memorable for the progress they have shown and to some of the most marked features of this progress I will now oriefly call your attention. It may be of interest in this connection to note the following figures, showing the growth of the population of the United-States during the last three decades :

Jan 1, 1881

By R. Stefanko

This first Annual Report covers the work on Contract No. H0377043 "Cable for Face Equipment", from August 1, 1977 to July 31, 1978. It reports the progress in the three areas of over-and short-circuit protection, cable ampacity research and cable couplers. Field trips have established many interesting facts related to circuit breaker settings and cable size. For example, the determination of cable sizes depends on the RMS duty cycle current determined by a particular piece of equipment, but the actual selection of the cable to be used is often a function of the maximum allowable circuit breaker instantaneous settings as specified in Title 30. In order to avoid nuisance tripping as a result of instantaneous starting current field, laboratory and analytical studies are being conducted to determine proper settings and cable sizes Also an extensive program has been established to monitor the performance of high voltage cable couplers and determine their modes of failure. Various equipments are being designed for laboratory testing, and an extensive reeled cable experiment is also under way.

Jan 1, 1978

By H. P. Reid

Portland cement is manufactured under either of two general processes, the wet or the dry. The raw materials in general consist of limestone, shells, marl, cement rock, clay, shale, blast-furnace slag, etc., so proportioned that when calcined the desired composition will be obtained. In the wet process the combined raw materials are ground to extreme fineness in the presence of water, to a resulting slurry of from 30 to 50 per cent moisture content. The moisture of the slurry may be reduced by thickening or filtering processes for feed to the cement kiln or the slurry may be fed to the kiln with its full percentage of water. The dry process differs from the wet in that the surface moisture of the raw materials is removed prior to grinding. For the drying of these materials heat is required and in most cases is produced by burning of raw fuel either on grates or stokers before the dryers or in suspension in the form of pulverized coal, oil or gaseous fuel. The power required for making the cement is sometimes purchased from outside sources; sometimes it is generated from the heat in the waste gases leaving the cement kilns, or generated at the plants direct from raw fuel. We have, then, as the possible requirements of fuel in the cement industry: (1) fuel for power generation, (2) fuel for drying raw materials, including coal before pulverizing, and (3) fuel for burning the raw materials to cement clinker. There is no essential difference in quality required in fuel for burning the materials by the wet and,dry processes. Fuel fob Power Generation As there is nothing peculiar to steam generation in a cement mill power plant as compared with other power plants this use classification of such fuel will be found in other reports of the Technical Committee. Fuel for Drying Raw Materials and Coal Any fuels capable of producing moderate temperature gases may be used for drying raw materials. There is no problem of material contamination from fuels at this part of the cement manufacture to be guarded against.

Jan 1, 1932

By L. D. Rickets

The principles on which an art is founded are usually few and necessarily basic in nature, but he who wishes to achieve the power to select his aides and give success to important undertakings that may be entrusted to him in the future must ordinarily undergo years of drudgery in order to gain the experience that will enable him to distinguish such fundamentals through the haze of reenforcing detail that clothes and tends to disguise them. This especially applies to those who would dream dreams that may come partly true. Professor Henry B. Cornwall of Princeton was a graduate of Freiberg with mining experience in Mexico. He was my friend and mentor during my college life. In 1883 I finished my postgraduate course and had two offers of work to consider. His advice is very clear in my mind today. It was essentially as follows: I know something of the mines of Mexico and have crossed through the mountains of the West. The West possesses a vast area of mountain and valley. California has long had its gold mines, the Comstock and Gilpin County followed and now comes the discovery of Leadville. I believe the West, will become a great mining country. You can choose now to teach here or go to the mountains. Were I in your place I would go West and identify myself with mining.

Jan 1, 1932

By Thirnbeck M, Sione T, Petrie P, Leach TM, Mori W, Digan K, Harry K

Gold and lesser copper mineralisation are associated with porphyry-related vein systems periph-eral to two separate inferred intrusive centres north of Kainantu, Papua New Guinea (PNG). The intersection of NW trending structures, formed parallel to the Markham Fault, with NE trending transfer structures localise porphyry intrusions, and control vein distrib-ution.The Arakompa veins intrude pre-existing fractures in Akuna granodiorite, located proximal to an inferred porphyry. These veins are characterised by early quartz and later pyrite-chalcopyrite. Gold mineralis-ation is associated with Bi-Te phases in the sulphide veining. At Maniape, en echelon gash veins occur within the imbricate portion of a regional structure. Maniape is a high level carbonate-base metal gold system formed distal to the same porphyry source as Z ?-;4 kmmna

Jan 1, 1994

By Gerald Greene

Tan various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulfur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1) states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As.

Jan 1, 1935