Search Documents

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-technological cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By P. M. Wiltcher

The construction of a deep structural slurry wall in a restricted city centre location is always a challenging prospect. However, when the city is London and the site is bounded on two sides by high level canals and a main traffic highway on the third, the challenges are greater than usual. The paper discusses the design considerations required by the principal contractor to accommodate a single high level lateral support, value-engineered, bottom-up construction technique and the impact this had on the design detailing and construction of the slurry wall panels. This paper discusses the logistical challenges successfully overcome during the construction of 65,000sq ft of 40inch thick, 80ft deep structural slurry wall in the City of London. The paper reviews the benefits gained from using the state-of-the-art hydraulic grab and rotator system. Technological advances in computer instrumentation and real time monitoring were utilised to assist the grab operators in consistently delivering deviational control during excavation better than 1:200. With working space always at a premium on construction sites, the need for high quality, pre-fabricated reinforcement cages has never been greater. This paper reviews the argument for off-site fabrication of reinforcement members.

Jan 1, 2006

By Baptiste Laubie

Agromining is a phytotechnology aiming at producing commercial metal compounds from low-grade ores thanks to hyperaccumulating plants. The fern Dichranopteris dichotoma is a rare earth element (REE) hyperaccumulator, which naturally grows on former mine tailings in China. It accumulates up to 0.35% of REEs in its aerial parts. Different hydrometallurgical processes are currently developed to recover these elements directly from the biomass or from ashes after combustion. The process presented here consists of a direct extraction by EDTA solution, followed by precipitation with acid oxalic. Optimal precipitation pH and influence of organic matter are determined by modelling and by experimental studies. The final solid contains 4.3% of REEs, with calcium as the main cationic impurity (0.45% of the precipitate). The recovery yield is similar for major REEs and is around 70%. After optimization, upscaling of the process will allow the agromining development to recover REEs from secondary resources with more environmentally friendly techniques.

By Khoo Khyou Pin, Yoshiyuki Funaki, Hirotsugu Takeuchi, Ryoichi Urao, Naotatsu Asahi

"Steel is used to be ion carburized with mixing gas of methane and hydrogen. In carburizing, carbon in the methane decomposes and deposits on the steel by plasma, so methane gas flow may influence on ion carburizing of the steel. An apparatus in which works can transfer preheating, ion-carburizing and diffusion treating zones continuously was made for effective carburizing of steel. The gases were flown into above three zones with three different gas inlets. The hardness and microstructure of the works were investigated after ion carburizing and quenching. The steel is carburized deeper near the carburizing gas flow nozzle of the inlet than far from the nozzle. Hard surface layer fom1ed by quenching of ion-carburized steel.IntroductionGas carburizing is used for a surface hardening treatment which decreases fatigue and wear of the industrial parts used in automobile, machines etc. Ion and vacuum carburizing have been developed recently and applied to some industrial parts of restrictive purposes. The ion carburizing treatment which uses hollow cathode discharge (HCD ion-carburizing) is superior in energy saving, resource saving, environmental cleanness to the other carburizing treatment. Specially, carburizing energy can be saved in HCD ion-carburizing, because highly heated zone can be restricted in the range between work and subsidiary cathode where hollow cathode discharge arises, and the work is carburized in shorter tin1e in HCD ion carburizing method than other carburizing methods. Three treatments of preheating, carburizing methods and carbon potential controlling by hollow cathode discharge tried to be carried out in one continuous transferring series to carburize works more effectively, so the HCD ion-carburizing apparatus with continuous transferring system was made and gears of works were HCD ion-carburized in continuous transferring. The works were rotated themselves to get homogeneous carburizing by continuous transferring in glow of hollow cathode discharge."

Jan 1, 2000

By J. E. Dutrizac

Fracture-exposed surfaces of sphalerite samples having five different solid solution iron contents ranging from 0.0 wt% to 14.8 wt% Fe were leached for 15 to 120 s at 100°C in 0.3 M Fe(S04)1.5 -0.3 M H2S04 media. The reacted samples were examined using X-ray photoelectron spectroscopy (XPS) which provides chemical state information on the first few nanometers of the solid surface. Surface compositions show that the leaching rate increases with increasing solid solution iron content of the sphalerite. Detailed evaluation of high resolution S2p spectra show that the leaching progresses via the formation of polysulphide species. Disulphide species were not detected in any of the experiments. Examination of the Zn2p and Fe2p spectra indicate little change in the chemical states of these elements over the duration of the experiments. Longer leaching times resulted in the generation of elemental sulphur. The ratios of elemental sulphur to dissolved ferrous ions and zinc suggest that less than 5% of the sulphide is oxidized to sulphate. Morphological studies showed that the elemental sulphur commonly formed at a few isolated sites, such as the grain boundaries. Furthermore, euhedral sulphur crystals were often identified. These observations suggest that at least part of the elemental sulphur forms via dissolved sulphide species which are oxidized in solution by ferric sulphate.

Jan 1, 2003

By H. Sevim

In long-term open pit production planning, a series of nested and maximum-value pits is usually generated first. These pits are then considered as possible pushbacks over a number of planning periods. To determine the best pushback in each planning period, the pits are evaluated for their technical and economical feasibilities under certain production constraints. Parameterization is a commonly used technique to generate a series of pits. In almost all cases, however, some of the consecutive pits generated by this technique are too far apart from each other. This is called the "gap" problem. It may make the entire pit series useless for production planning purposes. A new pit gener¬ating algorithm has been developed to overcome the gap problem. Through this algorithm, a series of nested maxi¬mum-value pits can be generated with a controllable size increment. The logic of the algorithm is illustrated through a small hypothetical case. Its capability of generating maximum-value pits that are as optimal as those generated by parameterization and its advantages over parameteriza¬tion are presented through an actual gold deposit case.

Jan 1, 1996

By I M. Platten, Y Xie, B W. Cuffley, S C. Dominy

"Geometallurgical programs require the collection of representative samples for geochemical, mineralogical and metallurgical test work. Such protocols must be designed to suit the style of orebody in question. The distribution, proportion and size of gold particles have a direct impact on the effectiveness of sampling and test work protocols, and the gold recovery processes employed. Characterisation studies focusing on ore mineralogy, and gold particle deportment, size and distribution are required. High resolution X-ray computed tomography provides a non-destructive method for analysing the 3D nature of gold in rock samples. It can be used to calculate the modal abundance, particle size and distribution of gold in the sample volume. This paper presents a case study of the imaging of in situ gold particles in a high-grade gold ore. The Nick O’Time reef system comprises laminated quartz veins, which locally bear extreme grades of up to 100 oz/t gold. The mineralisation has previously been characterised from both a mineralogical and metallurgical perspective. Eight visible gold-bearing vein samples were scanned using X-ray microtomography. Microtomographic data were integrated with previous mineralogical and metallurgical test work outputs.CITATION:Dominy, S C, Platten, I M, Xie, Y, Cuffley, B W and O’Connor, L, 2016. Characterisation of Gold Ore from the Nick O’Time Shoot (Tarnagulla, Australia) Using High Resolution X-ray Computed Tomography, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 241–254 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By J G. Shellnutt, Y Iizuka, T W-Y Hsia, T-C Liu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of magmatic oxide ore deposits hosted in chemically-evolved layered gabbroic intrusions is attributed to a variety of petrological processes, but there is little to no consensus on the general applicability of each model. Complicating the matter further is that many layered gabbroic intrusions are spatially and temporally associated with alkaline A-type granites, suggesting that there is a petrogenetic relationship between the two types of chemically different rocks. Our experimental results show that petrological modelling using a starting composition of high-Ti basalt from the Emeishan large igneous province can produce evolved silicic liquids that resemble the compositions of microgranular enclaves from the syenitic unit of the bimodal, oxide ore-bearing Baima igneous complex. The experimental results confirm that bimodal gabbro-granitoid complexes can form from a common parental magma and that early crystallisation of Ti-rich magnetite can explain the formation of the oxide ore deposits in the lower parts of the layered gabbroic intrusions. We conclude that crystallisation of a typical high-Ti basaltic parental magma can produce world-class giant magmatic oxide ore deposits and that the occurrence of some alkaline granites may be an indicator of their presence.CITATION:Shellnutt, J G, Hsia, T W-Y, Liu, T-C and Iizuka, Y, 2015. Cogenetic formation of the peralkaline syenite and oxide ore-bearing layered gabbroic intrusion of the Baima igneous complex, Emeishan large igneous province, south-west China , in Proceedings PACRIM 2015 Congress, pp 317–324 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Robert Hopler

The use of electrical fuzes is rapidly superseding the old cap and fuse method of firing blasts. It is therefore desirable that the details of this kind of blasting should be more generally understood

Jan 1, 2006

By Ernest G. Enck

Expanding markets and technological investigations now in progress for commercial production of titanium metal and alloys, as well as expanding uses for the oxide, have resulted in greater production, increased prices, and accelerated search for additional commercial occurrences of titanium minerals. For more than 50 years rutile has been used in moderate quantities in ceramics, in the production of ferrotitanium, as well as nonferrous titanium alloys. During the early 1930's, use of pure titanium dioxide was introduced as an ingredient of coatings for electric welding rods. For technical and economic reasons rutile was soon found to be as good or better for mild steel welding rods, and this use continues to account for a good share of the rutile sales in the U. S.

Aug 1, 1956

By J. P. Morgan, D. B. Stewart

"AbstractLoad-haul-dump machines equipped with. a torque converter and hydraulic pumps have been field tested by means of an engine monitoring instrumentation package. It was found that owing to parasitic losses in the ancillaries and drivetrain, maximum available useable pourer may peak at less than full engine speed. Simple reduction of engine speed may save 15 to 25 percent on fuel consumption, with no significant loss of available power. On some machines, speed reduction will require modification of the torque converter . The cost of this modification, when necessary , would be offset by reductions in exhaust emissions, ventilation requirements, fuel consumption , heat, noise and hydraulic system maintenance, and by increased life of rotating components and filters and machine availability.IntroductionTHE CANADIAN EXPLOSIVES ATMOSPHERES LABORATORY, in conjunction with Deutz Canada Limited, has designed, constructed and field tested a portable instrumentation package. This package monitors diesel engine performance in underground mining machinery by continuously recording engine speed and volumetric fuel delivery. During tests designed to determine the engine load and speed conditions for the various segments which constitute actual underground operation of a Deutz F6L 714-powered 4-yard load-haul-dump machine, it was discovered that an unexpectedly large percentage of the engine power was required to overcome the ancillaries and drivetrain drag (1). That this large component of engine power is functionally related to engine speed rather than the operator's needs was verified by repeat tests of the used 4-yard machine and by testing of a new 5-yard machine powered by a Deutz F 8L 714."

Jan 1, 1977

By William Petruk

Many gold operations lose gold during processing because some ore characteristics which affect recoveries have not been determined, and consequently the plant could not be designed to account for them. The ore characteristics can be determined with mineralogical techniques by analyzing the plant feed, final tailings and mill products. The plant feed and/or final tailings are commonly analyzed first as a separate project. Mill products are analyzed only if the process employs a minerals separation circuit to produce a concentrate (e.g. secondary flotation circuit to concentrate gold-bearing arsenopyrite), and if assays and materials balances indicate a recovery problem in the minerals separation circuit. Many ores have been evaluated at CANMET on a confidential cost-recovery basis by custom-designing a work plan which was dependent upon the problem and on the characteristics of the ore. The reasons for gold losses have been identified in most cases, and suggestions for modifying flowsheets have been proposed. The methods used in performing the analyses are described in this paper, and non-confidential results from in-house projects are provided as examples of the benefits of such analyses. The analytical methodology involves a combination of the following procedures: -producing heavy mineral concentrates and identifying the gold minerals in the concentrates; -determining quantities of invisible gold in gold-bearing sulphides, sulpharsenides, etc. by SIMS; -determining quantities and liberation characteristics of all gold minerals and gold-bearing minerals in the sample; -finding and identifying gold minerals in silicates; -extensive grinding and cyanidation to determine the ultimate amount of cyanidable gold; -determining impact of clay minerals and graphite; -performing a mineral balance for the gold in each sample; -performing a materials balance to determine the distribution of the gold minerals, gold-bearing minerals, and other minerals throughout the flowsheet, and; -interpreting the results.

Jan 1, 1995

EUGENE WESLEY SHAW,* Washington, D. C. (written discussion ?).-Studies of the probable future production of oil wells and fields-particularly those in the nature of the recent work by Lewis and Beal, having the object of increasing the percentage of recovery-rank, in both practical and theoretic value, very high, if indeed they do not outrank all other petroleum investigations except structural surveys. Even such surveys, although saving untold millions that might have been spent in prospecting unpromising territory, may have less ultimate value than generally supposed, for it may perhaps be argued that much if not most of the condemned territory will sooner or later be tested-some is already productive-and the most that can be rightly claimed is the recovery of cream first; also that the consumption of the richest portions first cannot be extenuated, as it might with some resources, on the ground that if the best is not taken now it will deteriorate.

Jan 5, 1918

By Jean L. Leroy

The Lead Smelting works of Metallurgie Hoboken S.A. are located on the banks of the river Scheldt a few miles South of Antwerp. Lead refining began at Hoboken in 1687, when it was restricted mainly to desilverizing lead bullion from Central America. Since then, various changes have been made to develop the works into a comprehensive and integrated custom smelter and refinery. Multiple hearth roasting furnaces, down-draft sinter machines and blast furnaces of standard design are used for the treatment of "complex" lead ores and secondary materials. A lead refinery based on the Harris process, with Parkes desilverizing followed by vacuum dezincing and Kroll Betterton debismuthizing was commissioned in 1967. Facilities for the recovery of precious metals, bismuth, antimony, arsenic and sulfuric acid are available. Special problems arise from the presence of large quantities of copper in the materials treated.

Jan 1, 1970

By Geza Kisvarsanyi

Ore deposits composed of enargite, tennantite, gold, and pyrite have been mined in volcanic rocks of Oligocene age (35 m.y.) at Recsk, Hungary. Vertical and horizontal zoning of the alunitic-argillic alteration and of the ore minerals led to the concept of an intrusive heat source at depth. Subse-quent drilling disclosed a series of ore deposits in a zoned pattern in and around a stock, separated by a barren gap of 1000 meters from the shallow ore. The ore system is in a intracaldera horst-graben structure, formed by collapse and intrusion in a microplate subduction. volcanic-arc tectonic environment.

Jan 1, 1987

By Dan Witkowsky

For the 36th consecutive summer, the Colorado Mining Association Education Foundation and the Colorado School of Mines have sponsored “A Total Concept of the Mining Industry” for kindergarten through grade 12 teachers. Teachers from 34 states, plus the District of Columbia and two foreign countries, have graduated from the four-week course. They received six hours of recertification credit. This summer 31 teachers from Colorado, Kentucky, Virginia and Alaska completed the program. The course is unique from other shorter courses in that it solicits teachers of all disciplines from all K-12classes. In addition to the expected earth science and mathematics teachers, the Class of 2004 consisted of educators who teach music, chemistry, biology, social studies, history, basic English and world history. Others in the program included those who teach American history, physical and life science, remedial reading, consumer/family studies, “world of work,” language arts, engineering technology, environmental science, world geography, human anatomy and physiology, and business.

Jan 1, 2004

By C. W. Davis

This paper is the second of a series of progress reports on a study, of the hydrometallurgy of manganese which is being conducted in an endeavor to make possible utilization of the large deposits of low-grade domestic manganese ores that occur in several States. There are at least four processes in which a knowledge of the action of SO2 gas on manganese oxides at elevated temperatures may prove of value. One ,of these involves dissolution of manganese from ores. The Bureau of Mines has investigated the hydrometallurgy of manganese by a process in which SO2 gas, a waste product at many smelters, is passed into water to form a solvent for manganese. Although Several manganese minerals acre readily dissolved, rhodochrosite (MnCO3) was attacked but superficially.§. Recent experiments have shown that a roast at 650 to 900°C converts the manganese of rhodochrosite to a form that is quickly dissolved by a weak SO2 solution. Introduction of smelter gases containing as much as 5 per cent SO2 during such a roast would not add much to the cost of the operation and might result in the formation of considerable water-soluble manganese sulphate.

Jan 1, 1930

By R. Matusewicz, A. Kaye

Ausmelt Top Submerged Lancing (TSL) Technology has gained widespread commercial acceptance in non-ferrous applications, including the processing of lead and zinc primary concentrates and secondary (post-consumer) materials. TSL is highly flexible and efficient, and is one of the few technologies which can process primary and secondary feeds, and use varying fuels, to deliver high recoveries and excellent environmental performance. With the recent high value of both lead and zinc, and an escalating awareness of the sustainable use of resources, focus on the processing of secondary feed material sources has surged. Ausmelt Technology has proven to be well suited to the economic recovery of values, with twenty-two (22) Ausmelt furnaces processing lead and zinc bearing feed sources now in operation, under design or construction. This paper describes Ausmelt's progress in the fields of lead and zinc processing, and developments in new processing areas such as EAF dust processing and linking to innovative hydrometallurgical technology. Ausmelt has recently committed to the Whyalla Zinc project as the owner/operator of a facility for the treatment of zinc bearing secondary feeds. This project is due for start up in the first quarter of 2008.

Jan 1, 2008

By Y. De Gao, C. Gang Zhong, X. Yang Qiu, Li Wan

The chelating reagents are used as effective collectors in wolframite flotation, and certain metal cations need to be added using chelating collectors so as to activate valuable minerals and obtain good flotation indexes. Different metal cations will result in different reactivity with collectors, in order to select the effective activator in BHA flotation of wolframite, the activation effectiveness of different metal cations on wolframite ((Fe,Mn)WO4) flotation were studied using pure minerals. The results showed that the wolframite activation by Pb2+was the best among the selected cations. The maximum flotation recovery of wolframite was found to be 95.58 % under conditions of 100mg/LBHA and 1×10-4mol/L of Pb2+at pH 9. The dosage of Pb2+needs to be controlled in an optimum range. Also, the activation mechanism of Pb2+ on BHA flotation of wolframite was investigated by measurements of contact angle, zeta potential, adsorption capacity and IR spectroscopy. It was found that Pb2+ could chemically adsorb onto the wolframite surface improving the flotability of wolframite and enhancing the adsorption of BHA on wolframite. When the dosages of BHA and Pb2+ were 100 mg/L and 1×10-4 mol/L, the adsorption quantity of BHA on wolframite sharply increased up to 0.30 mg/L at pH 9 compared with wolframite treated with only BHA.

Jan 1, 2014

By J J. McEwan

Silver tarnishes readily in common atmospheres and is accelerated in humid atmospheres. Tarnish is the formation of silver sulphide on the surface of silver when it is exposed to a wide range of sulphur-containing atmospheres. Tarnish is unattractive and highly undesirable, and can be removed either with a silver polish or a chemical dip. Dips are generally only recommended when heavy black tarnish cannot be removed with a polish, and care must be taken during cleaning because these can contain aggressive chemicals and give off hazardous and unpleasant smelling fumes. Polishes work best for large areas of plain undecorated silver, and form part of a regular cleaning programme. Some polishes contain chemicals that inhibit tarnishing, but these generally only have a short life. Several methods have been developed to reduce tarnish formation on Silver; these include alloying, surface treatment, and coatings. The authors evaluated a range of self-assembled monolayer (SAM) surface treatments and coatings in earlier research. Four treatments/coatings increased the time to noticeable tarnish by more than ten fold, and the results were reported at the International Corrosion Congress (ICC) in 2005, and at the Mint Directors Conference (MDC) in 2006. SAM treatment using 95% 1-hexadecanethiol (C16H34S) was found to give good anti-tarnish performance and showed potential for the commercial treatment of Sterling silver. Therefore research was performed to optimise the methods of application of this type of coating to provide an easier, faster, and more-user friendly technique to provide an anti-tarnish treatment. Keywords: silver, tarnish resistant coatings.

Jan 1, 2006