Search Documents

By Jerome J. English, Gordon W. Powell

An experimental investigation and mathematical analysis of the thermal-dilation behavior of the titanium alloy Ti-7Al-3Cb have shown that the linear dimensional changes associated with the polymorphic transformation need not be isotropic. The absolute magnitude of the linear dimensional change, which may be either positiue or negative, associated with the cr-p transformation is dependent upon the relutzve volumes of different orientations of the transformation product. It is hypothesized that the dilation irregulati-ties that have been observed during the polymorphic transformation of pure, coarse-grained titanium and other titanium-base alloys can be explained in the same manner. When titanium is heated above about 165O°F, the hcp a structure transforms to bcc 0. Thermal-dilatioh measurements have shown that the transformation is accompanied by a decrease in length of 0.16 pct.' Such dilation behavior would be expected because the volume of the hcp unit cell is about 0.3 to 0.4 pct greater than that of the bcc unit cell. A recent investigation2 of the thermal-dilation behavior of an experimental a-p* titanium alloy, Ti- 7A1-3Cb, containing 0.06 wt pct 0 showed that its dilation behavior during the polymorphic transformation differed substantially from that reported for unalloyed titanium. The first time the alloy was cycled through the transformation, the dilation curve closely duplicated that of unalloyed titanium. However, upon repeated cycling through the transformation temperature range, both the magnitude and the sign of the dimensional change associated with the transformation were observed to vary with each cycle. This investigation was undertaken to obtain additional data on the dimensional changes associated with the polymorphic transformation in the Ti-7A1-3Cb alloy and to determine the cause of the dimensional irregularities. After testing, the specimens were examined metallo-graphically. In addition, Laue back-reflection patterns were obtained from selected sections taken perpendicular to the specimen axes to determine the a orientations present in these sections. White radiation from a tungsten target and a 0.1-mm-diam collimator were used to produce the diffraction patterns. RESULTS Dilation Curves. Three types of thermal-dilation curves were obtained when the a-8 titanium alloy was heated and cooled through the transformation temperature range. These three types of curves are illustrated in Fig. 1. The type I curve represents what is considered normal behavior, because the dilation change is what would be expected on the basis of the volumes of the unit cells of a and p. The Type I1 curve is the inverse of Type I. Normal behavior is characterized by an expansion on cooling through the transformation, whereas a contraction takes place in the Type 11 curve. With Type ni behavior, no clearly distinguishable length change occurs during the transformation. No other anomalies that might be indicative of other phase transformations were observed in the dilation curves at lower temperatures. Apparently, the cooling rate was low enough for equilibrium to be reached during the 0 to a transformation. Table I lists the types of dilation curves observed during the polymorphic transformation as a function of the direction of measurement and cycle number. The A1 value was determined by extrapolating the low-temperature (a + 5 pct p) and high-temperature (100 pct p) segments of the dilation curves to a common temperature and measuring the difference in the or-dinates at that temperature, see Fig. 1. The transformation occurs over a temperature range in this alloy, so the magnitude of A1 is not an absolute value but depends on the choice of temperature. A mean temperature, T,, within the transformation temperature range was selected for the measurement. T, on cooling occurred about 100°C lower than T, on heating. The first time each of the three dilation specimens was heated to above the temperature, that is, Cycle 2, normal Type I behavior was observed. In Cycle 3, two deviations from normal behavior occurred. First, during cooling of the longitudinal specimen, a substantially larger expansion, +0.21 pct, was measured as 0 transformed to a compared with +0.03 pct in Cycle 2. Second, the thickness specimen was observed to undergo a contraction instead of the anticipated expansion on cooling. Continued cycling of the three specimens from room temperature to 2500°F produced additional changes in the dilation behavior. These changes did not seem to be related to the fabrication direction of the alloy because the values of a1 for the longitudinal, transverse, and thickness specimens varied unpredictably in magnitude and sign. Furthermore, both the longitudinal and transverse specimens showed all three types of dilation curves at least once during the six cycles that they received. Fig. 2 is a sketch of the transverse specimen after

Jan 1, 1967

By G-L. Wu, X-B. Liu, C-Y. Zhou

"The static recrystallization behaviour of Ti-Nb microalloyed high-strength steel during hot deformation was studied by conducting double-hit hot compression experiments using a Gleeble-3500 thermomechanical simulator. The effects of deformation temperature, strain rate, strain, and initial austenite grain size on the static recrystallization fraction are discussed. The static recrystallization kinetics were modelled, and the results show that the static recrystallization fraction increased with deformation temperature, strain rate, and strain and interpass time. The static recrystallization activation energy Qs was 326.05 kJ mol-1. Comparison of the experimental results and predicted results indicates that the effects of deformation parameters on the static recrystallization in multistage hot deformation are significant. The predicted results are in good agreement with the experimental results. IntroductionIn hot-forming processes, complex microstructures are often induced by multiple hot deformation mechanisms (Zhang et al., 2014; Liang et al., 2015). The softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by the corresponding microstructural evolution (Wu et al., 2010). It is well known that dynamic recrystallization (DRX); metadynamic recrystallization (MDRX), which occurs by the growth of DRX nuclei during intervals of deformation; and static recrystallization (SRX), which occurs by nucleation and growth during the intervals of deformation, can significantly alter the austenite grain size (Chen et al., 2015. Chen, Sui, and Cui, 2014; Mao et al., 2014). The long interpass times allow complete SRX to take place if the steel is being rolled above the interpass recrystallization stop temperature (Tnr), i.e. in the absence of carbonitride precipitation (Siciliano, 2000). In recent research, microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient in achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Bandyopadhyay et al., 2011). The alloying elements Nb, V, Ti are widely used in high-strength low-alloy (HSLA) steel to achieve the desired strength and toughness properties with solid-solution strengthening, precipitation hardening, grain refinement, and dislocation strengthening (Opiela, 2014; Chen and Yu, 2012). The wide applicability of alloying elements in HSLA steel is due to the fact that heat treatments are not required after forming of the parts, which results in time and cost savings."

Jan 1, 2017

By L. W. WALLACE

IN an engineering fashion we have made an assay of the engineering profession, using as a. sample the engineers listed in "Who's Who in America" (1928-1929). We are aware that some will say it is an unfair sample; that it came from the best mine. This is readily admitted, with this qualification: that all engineers and architects by virtue of their training and experience have been freed of most of the dross to which mankind is heir. They are -a selected group to begin with, having all the potentialities those in the sample possess. We are also aware that some will say a part of those included in the sample are not engineers. Our answer to that criticism is this: An engineer is no less an engineer because for the time being he is president of a bank, a university, an opera company, or a hotel company. Moreover, he is no less an engineer because he is a governor of a commonwealth, a United States senator, a member of the Cabinet, or the President of the United States.

Jan 1, 1929

By Michael Somerville, Paul Voigt, Chunlin Chen, Alistair Burrows

To date, many types of primary concentrate have been smelted using the ISASMELT™ technology, with annual smelting of copper concentrate alone exceeding 7 million tonnes. Most of this material could best be described as chalcopyrite concentrate, owing to the predominance of copper attributable to this single mineral. Chalcopyrite concentrates lend themselves readily to smelting with a fayalite slag, and producing a matte containing 55–65 wt% Cu. However, the ISASMELT™ technology also stands ready to meet future copper demand through the treatment of new types of concentrates containing relatively low iron and high silica levels. Various slag systems have been considered for direct-to-blister smelting. They have been evaluated computationally, using the MPE thermodynamic modelling package, and practically, at pilot scale. The lime-silica-iron oxide slag was found to have the lowest slag make, lower dissolved copper and hence lowest copper losses. Based on the outcomes of the modelling and pilot scale testwork a future smelter flowsheet has been defined, comprising a single ISASMELT™ direct-to-blister furnace, an electric slag cleaning furnace, and appropriately designed anode furnaces.

Mar 1, 2017

By G. A. Gunderson

Since our time is very limited, I would like to relate to you as best as I can a few important areas that I think may be helpful. 1.) The Real Difference between Dense Phase and Dilute Phase Pneumatic Conveying: Within the many variations of so called Dense Phase conveying, it is often difficult to determine to what degree a system is Dense Phase or if, in fact, it is a Dense Phase system at all. A system that appears and is generally known to be Dense Phase can under certain operating conditions perform as a Dilute Phase system. If, for instance, a high pressure system, which is generally a Dense Phase system, operates at 60 PSIG, say 4 atmospheres, utilizes enough air volume, the conveying velocity will easily exceed the normal design velocity of a typical Dilute Phase system. Now, on the other hand, a low pressure system which we will term a Dilute Phase system, operating at 15 PSIG; say 1 atmosphere, can convey a given product at well below the saltation velocity, like a Dense Phase system.

Jan 1, 1977

By Arthur M. Miller

FROM the time of its establishment in 1933, the Tennessee Valley Authority has been active in the field of phosphates. Under the T.V.A. Act it has a broad Congressional mandate to guide a unified development of the resources of the region for the long-range benefit of the people. As one phase of this function, it is directed to co-operate with farmers in the experimental large-scale use of improved fertilizers and development of better fertilizer practices. Following careful study, it was concluded that the objectives of this phase could best be attained by soil rebuilding through the use of phosphatic fertilizer and lime in an improved farm management sys- tem. This activity was launched through a program of test and demonstration on farms and simultaneous technical investigations to develop new and improved phosphatic fertilizers. Phosphorus has since become a keystone of the Authority's resource development and conservation program. Human effort is being conserved by phosphate utilization on the farm, and mineral conservation has been promoted by technical developments in phosphate mining and manufacturing operations.

Jan 1, 1944

By H. T. Green, R. M. Brick

True stress-strain data on alloys of pure iron with up to 2.4 pct Al were obtained in the temperature range +100° to —185°C. Alumi-num was found to reduce yield and flow stresses of iron at low temperatures but to have little or no effect on ductility. The effects of temperature and composition on strain hardening are discussed. SEVERAL independent studies of the behavior of high purity iron binary alloys at low temperatures are now in progress in attempts to evaluate systematically the variables affecting the low temperature brittleness of ferritic steels. This paper reports the results of one such investigation in which the tensile properties of aluminum and aluminum plus silicon ferrites were measured from 100" to —192°C. True stress-natural strain data have been obtained in order to evaluate as many as possible of the parameters which describe the behavior of the materials involved. In comparable studies at the National Physical Laboratory in England, iron and iron alloys of high purity have been produced' and tested at subat-mospheric temperatures.' True stress-natural strain curves were obtained there also. The purest iron contained 0.0025 pct C and 0.001 pct O and N. Even this, as normalized at 950°C following hot rolling, showed little ductility at -196°C. The grain size was ASTM No. 3, and the room-temperature yield strength was 17,800 psi (which seems too high for pure iron). Some of the NPL irons contained considerably more oxygen and demonstrated intergran-ular fracture at —196°C. The authors2 carefully differentiated between intergranular fractures associated with excessive oxygen content and transcrys-talline cleavage with little ductility encountered at —196°C in the purer material. The cleavage stress was half again as great as that associated with inter-granular fracture. Test Material, Preparation, and Procedures Of a number of Fe-A1 alloys produced, eight were considered to be sufficiently pure for testing. Partial chemical analyses (Table I), low observed yield points, and high ductilities indicate these alloys to be comparatively pure for vacuum-melted irons of sizable ingots, 5 Ib or more. To produce the binary Fe-A1 alloys, electrolytic iron was melted in air, cast into slabs, and rolled to strips 0.010 in. thick. These strips, joined into a continuous ribbon and wound into 2 1/2 in. diameter spools, were subjected for four weeks to a moving atmosphere of purified dry hydrogen in a stainless-steel tube at 1050" to 1150°C. Charges of these spools were melted in beryllia crucibles under good vacuums (1 micron), and aluminum (99.97 pct Al) was added to the melts. Compositions of these alloys are recorded in Table I. The ingots were hot forged and then cold rolled at least 65 pct to 3/8 in. rods which were vacuum annealed to the desired grain size, approximately ASTM No. 4, prior to machining into tensile test bars. All tensile specimens had gage sections 1 in. long, with a fillet of 1.5 in. radius to the shoulder. Gage diameters were 0.250 in, except for a few rods where additional cold work required use of a 0.200 in. gage section. After machining, 0.002 in. was removed from the gage diameter using 240, 400, and 600-grit metallo-graphic papers. The final polish with 600 grit left the fine scratches running in the longitudinal direction. By this means, surface metal strained during machining was removed. A few specimens heat treated after machining were similarly reduced 0.004 in. to remove any material affected chemically by the atmosphere during heat treatments, as is discussed in a later section. Tensile tests of the eight alloys at constant temperatures from +100° to —185°C were performed in apparatus which has been described." The essentials include a double-walled insulated metal vessel which contained the liquid heat-transfer medium surrounding the test specimen. A constant temperature was maintained by means of a pyrometer which regulated the pressure of dry air driving liquid air through a copper coil. Temperature variation was less than ±2°C during a specific test. For axial straining, two lengths of case-hardened chain, terminating in simple shackles, loaded the specimen through threaded grips. The lower grip bar passed through a hole in the bottom of the test vessel to which it was joined by a thin-walled

Jan 1, 1955

By SenYang Qian, ShuangYu Du, Bo Wang, Jieyu Zhang, Jian Zhao

During the solidification process, the flow pattern of the molten steel has significant influence on the formation of solidification microstructure. In present study, the solidification microstructure of 30Cr2Ni4MoV steel ingot under different intensities of mechanical oscillation(forced convection) was simulated by using ProCAST®software. The results showed that the increase of the intensity of oscillation could restrain the development of the columnar grains and refine the grains. As the intensity of oscillation increased, the proportion of columnar grains decreased and the proportion of equiaxed grains increased. When the intensity of oscillation was at a low level, the effect of refining grains could be improved obviously by increasing the intensity. However, as the intensity increased to over 0.833, the effect of refining grains would not be improved.

Jan 1, 2016

By J. M. Smith, D. Kunii

Effective thermal conductivities of sandstones filled with stagnant fluids were measured using a steady-state technique. Data were obtained for seven sandstone samples, taken from four different locations and ranging in permeability from 18 to 590 md. The measurements with gases (helium, nitrogen, air and carbon dioxide) covered a pressure range from 0.039 psia to 400 psig. Data were taken for four liquids — n-heptane, methyl alcohol, 79.8 weight per cent glycerol-water solution and pure water at atmospheric pressure. The experimental results were used to evaluate the theoretical equations for predicting stagnant conductivities developed earlier 4 The low-pressure measurements permitted evaluation of the consolidation parameter bpDp/ks (necessary to utilize the theory) for the various types of sandstones. Using these characteristic values, the tbeoretical equations correlated well with the experimental conductivity data for the several fluids and rock samples. INTRODUCTION An aspect of heat transfer in solid-fluid systems of considerable current interest is the effective thermal conductivity of porous media. The stimulus for study of the subject arises from the need for sound procedures for designing thermal methods of petroleum production. The general system occurs when there exists a flow of fluid through the pores of the solid material. However, a logical starting point in developing a theory for predicting the effective thermal conductivity in the general system is to attack the special case when the porous solid is filled with stagnant fluid. Since the flow rates anticipated in thermal production processes are very low, such stagnant conductivities k,O are also of practical significance. Kunii and Smith4 recently reviewed the existing data for stagnant conductivities and proposed a theory for heat transfer in porous rocks. This leads to equations for predicting the stagnant conductivity as a function of the properties of the fluid and solid phases. The existing experimental information1-3,5,7,8 covered a range of porosities and agreed well with the theory. However, the available data were insufficient to examine critically the effects of two important properties on koe, — the thermal conductivity of the fluid and the pressure. The objectives of the present study are twofold: (1) to measure the effect on koe of (a) the pressure for gases, and (L) the thermal conductivity of the fluid kg for bloth gases and liquids; and (2) to determine for rocks of different porosities and permeabilities the apparent solid conductivity ks and the consolidation parameter bpDp/ks required in applying the theoletical equations. Measurements extrapolated to zero pressure are helpful in evaluating ks and the consolidation parameter. However, the extrapolations must be based upon data obtained at low pressures because in small pores the molecular conductivity of the fluid may be unusually depressed. This occurs when the mean free path of the molecules is of the same order of magnitude as the pore diameter, that is, in small-diameter pores at low pressures. The phenomenon has been studied recently by Schotte6in beds of unconsolidated fine particles. With particles in the size range of 45 to 200 microns, a significant reduction of kg with pressure was found even at absolute pressures greater than 1 atm. In the sandstones employed in the present investigation, pore diameters lower than those experienced by Schotte are likely, so that the effect would presumably be greater. SCOPE OF MEASUREMENTS Stagnant conductivities were measured for four types of sandstones using a total of seven samples. The characteristics of the samples, including porosity and permeability values, are given in Table

By F. Milton Lewis, James L. Coburn

In this paper the economics for a conventional comminution system, consisting of three stage crushing and one stage ball mill grinding, are compared to a semi-autogenous/ball mill comminution system. Capital and operating costs for a copper concentrator in Arizona at two levels of production, 20 and 40 thousand short tons of ore per day, are estimated. In order to minimize the investment and operating costs, large size equipment is selected for all four cases. These cost data are evaluated and conclusions are presented.

Jan 1, 1982

By Robert B. Gordon

The Reverse Curve Tunnel Project was located in Glenwood Canyon, Colorado approximately twelve (12) miles east of Glenwood Springs. The Project was one of many being constructed over a period of time by the State of Colorado, Department of Highways to improve Interstate 70 to four lanes as it travels thru the environmentally sensitive Glenwood Canyon. The Project consisted of excavating and concreting a tunnel approximately five hundred fifty (550) feet long, forty two (42) feet wide, and thirty two (32) feet high. The designer was Parsons, Brinkerhoff, Quade and Douglas, with geotechnical consultation provided by Woodward Clyde. CONSTRUCTION CHALLENGES There were several significant construction challenges presented primarily by the physical location of the Project. In this study each problem will be discussed, as well as how it was overcome by construction methods and/or design requirements. Portal Excavation - One of the most difficult areas of work on the Project consisted of excavation and stabilizing the East and West Portal rock prior to tunnel excavation. The Reverse Curve Tunnel passes through a sheer walled cliff face which is approximately two hundred fifty (250) feet high. Geologically the cliff consists of primarily sedimentary deposits with open, weathered joints and vertical faulting. Before the tunnel excavation could begin, a narrow sliver cut had to be excavated and rock

Jan 1, 1989

By Robert M. Cox

The principal factor that must be determined for the effective design of a coal mine roof bolt support system is the maximum stable tension that can be developed with a given bolt assembly in a particular roof rock. There are four basic types of roof bolt anchorage techniques available: (I) the splitwedge; (2) mechanical expansion units; (3) resin point anchors or grouted expansion units; and (4) the cone shell which is placed in a reamed hole. A study of this problem has been made which includes theoretical analyses, laboratory experiments and field tests. A static free-body analysis of each of the anchorage techniques has provided formulas for predicting the anchorage capacity for a particular rock from the results of standard pull tests. The formulas also provide an insight into the anchorage mechanism of technique and allow for a comparative evaluation of the methods for design purposes. The theoretical analyses also indicate clearly the pertinent variables affecting the anchorage mechanism of each method.

Jan 1, 1977

By H. N. Herrick

THE flow characteristics of drilling muds, as described in this paper, and the method given for solving problems relating to the flow of these muds through pipe and accessory equipment, are based on a conception that drilling muds are plastic solids like paints or greases; not liquids. The data presented in this report have been obtained from studies of California muds, chiefly those used in the Kettleman Hills field, by the Producing Department of the Standard Oil Company of California. Although no claim of scientific exactness is made for the formulas and diagrams, since the data upon which they are based, are not. complete even for California muds, the method has proved to be a convenient means for estimating, closely enough for practical purposes, the pressures required to force muds at various rates through pipe systems in which they are handled. Certain approximations have been made to simplify the procedures so that they can be used easily in the field.

Jan 1, 1932

By J. H. Viljoen, J. F. Morrison, C. H. Wyndham

SYNOPSIS Heart rates, oral temperatures, shovels/min and number of 3/4 ton cars/hour trammed over distances of up to 350 ft were measured in samples of 6-10 miners, engaged in tram-shovelling, at 76°, 84°, 86°, and 89°F wet bulb temperatures in stopes in a mine. From the results it has been concluded that a man with an 'average' maximum oxygen intake capacity of about 2. 8 litres/min should be able to work: at 6 shovels/min, or 30 cars/shift per two men, at 76°-84°F; at 5 shovels/min, or 27 cars/shift per two men, at 86°F; and at 4 shovels/min, or 24 cars/shift per two men, at 89°F wet bulb air temperatures. INTRODUCTION A number of gold mines in South Africa still use tram-shovelling extensively. In this method of rock removal from the face of the stope, Bantu mine workers load rock into cars and tram the cars to a centre gulley where they are emptied. Previous studies from this Laboratory3 have shown that tram-shovelling is one of the most arduous tasks underground. The rate of energy expenditure is relatively high, being an oxygen consumption of about 1.4 litres/min over a period of some hours. In cool air conditions the upper limit to the rate of production of the well-motivated men employed on tram-shovelling has been shown1 to depend upon their capacities for physical work of an endurance nature (as measured by their maximum oxygen intakes). However, in hot conditions the factors which set the upper limit to the rate of production are different. They are primarily the ability of the body to maintain a heat balance between the rate of heat production, due to physical work, and the hot atmosphere, so that the men do not develop excessively high body temperatures8. In order to give mine managers guidance on the 'optimum' rate of production of Bantu mine workers engaged upon tram-shovelling under different temperature conditions underground a study was carried out in a mine. The number of shovels per minute and cars per hour were recorded and heart rates and oral temperatures were measured throughout the duration of the shift on samples of 6-10 Bantu mine workers in different air conditions. The results of the study are recorded in this paper and conclusions are drawn as to the number of shovels per minute and cars per hour which Bantu mine workers of 'average' maximum oxygen intake capacity should be able to produce at wet bulb air temperatures of between 76° and 89°F without either excessive fatigue or danger of heat illness.

By H. Clare Horwood

"Three types of structures, the main shear zone, the north shear zone, and a series of hanging-wall fractures, contain all the orebodies so far discovered at the McKenzie Red Lake mine. Lenses and veins of quartz in these zones and fractures are the sources of the ore. The ore-bearing structures are unusual in that they are in a complex intrusive mass known as the McKenzie-Gold Eagle stock. They are believed to have been produced by compressive stresses from the south andsouthwest.The mine is on the northeast side of McKenzie island, in Dome township in the central part of the Red Lake area. The original discovery, the main shear zone, was made in 1928, about 3 years after the property was staked, by M. L. Bouzan who was in charge of prospecting and development work on the property. Subsequent diamond drilling and underground exploration led to the installation of a mill, which came into production early in 1935. The hanging-wall fractures were found branching out from the main shear zone during development work on the 350-foot level. The north shear zone was discovered in 1940.From 1935 when the mill began operation until the end of 1946 total production from the mine was approximately 269,349 oz. gold and 69,317 oz. silver, having a value of $9,679,739, recovered from 823,527 tons of ore.GENERAL GEOLOGYThe McKenzie-Gold Eagle stock has a total length of approximately 1 ½ miles and a width of about ½ mile. It was intruded into a complex synclinal fold in Timiskaming sediments. The sediments, which have been cut in only one place in the underground workings, are principally wellbedded greywackes. The stock is composed of large masses of diorite and granodiorite, a small mass of hornblende pyroxenite, and basic dykes of two ages. The diorite occurs as irregular masses in large measure surrounded by the granodiorite that it intrudes. It contains tabular crystals of andesine, having a maximum length of3/4 inch. The hornblende pyroxenite is an elongated lens or dyke in the diorite. The granodiorite masses occupy about two-thirds of the stock. Along its eastern side the main mass tends to become darker and more dioritic toward the diorite contact.Basic dykes of pre-vein and post-vein age are the youngest intrusive rocks at the mine."

Jan 1, 1954

By L. D. Fetterolf, G. T. Mahler, W. M. Peirce, R. K. Waring

Until recently, the only commercial method of producing magnesium has been fused salt electrolysis, despite a considerable amount of experimental work on the direct reduction of magnesium oxide. In this early work, a number of investigators demonstrated that magnesium oxide would react with any one of several reducing agents to produce magnesium vapor, but that the mixture of magnesium oxide and reducing agent must be heated to a high temperature even in a vacuum. In particular, it was demonstrated that silicon and aluminum are effective reducing agents and that when either of these is used the magnesium vapor can be condensed to massive metal. In spite of this knowledge, no successful commercial reduction process was developed, at least in this country, because of the operational difficulties imposed by the requirement of high temperature and vacuum and because of the high cost of the reducing agent. The outstanding experimental work done by Pidgeon, who carefully reviewed all of the known methods of making magnesium and then selected ferrosilicon reduction, overcame some of the operational difficulties. The process developed by Pidgeon comprises briquetting a mixture of calcined dolomite and reducing agent, preheating the briquets to about 600°C. in an externally heated alloy retort, reducing the MgO with silicon in an evacuated horizontal alloy retort heated externally to about II50 C., and condensing the magnesium vapor to a solid in a cold extension of the retort projecting beyond the front of the furnace. A major advantage of Pidgeon's process is that the retort is not cooled down between charges. Earlier investigators had used apparatus that necessitated cooling and reheating of the retort between charges. Early in January 1942, when the War Production Board was considering the Pidgeon process for quickly increasing the production of magnesium, The New Jersey Zinc Co. offered to have a research investigation of the process carried on, with the hope of assisting in its further development. This offer was accepted, and a two-retort pilot plant was built at Palmerton and put in operation on Jan. 29,1942. An intensive investigation of certain phases of the process was carried out in the ensuing four months. This investigation was completed in the last part of May 1942) and the pilot plant was then shut down. Subsequently, The New Jersey Zinc Co. was requested to have further development work done on the process, and a more extensive investigation was undertaken in August 1942 under contract with the War Production Board and under the supervision of the War Metallurgy Committee. This paper describes the ,phases of the investigation that are thought to be of sufficient general interest to merit publication.

Jan 1, 1944

By J. Vanderlaan

A proposed method of applying high-speed, non-destructive part scanning technologies to the production process of UO2 (Uranium Dioxide) fuel pellets is presented. The scanning process examines each pellet individually for correct surface roughness and any surface imperfection or defects. Using optical scanning methods, which consist of laser and CCD camera technology, the complete circumferential surface of the pellet is examined to meet the reactor fuel bundle specifications.

Aug 1, 2010

By Yimin Zhu, Dezhou Wei, Haijun Liang, Zhifu Zhou

Pyrite is one of sulfide minerals most widely distributed in the earth. During the flotating separation of metal sulfide and the floating desulfation of coal, it is often requaired to restrain pyrite. However, the result is not very satisfactory because of the little difference of floatability of minerals to be separated. The problem is extremely outstanding for the floating desulfation of coal. Researchers carried out a number of experiments with T. ferrooxidans (Yang et al, 2001; Zhou et al, 2000; Zhou et al, 2001; Wei et al, 2001) for an enhanced restraint to pyrite. The results showed that the T. ferrooxidans after being cultured works the best in restraining pyrite. After 10 min pretreatment, the removal rate of pyrite from coal is up to 80%~90%. The research results by Yuan Xin et al (Yuan et al, 2000) show that T. ferrooxidans can restrain effectively the floatability of pyrite and can reduce the recovery of pyrite from 95% to 8%. Though the restraining properties of T. ferrooxidans to pyrite have been proved by many tests and experiments, there are very limited reports on its restraining mechanism. Thus, a systematic experimental research is carried out in this paper.

Jan 1, 2003

By Wang Yingmin, Xu Zhuyun

There are 3 steps in the process of forming a mine ventilation system, (1) selecting a reasonable ventilation pattern (included pit shaft arrangement); (2) optimizing of the ventilation network and (3) computing and outputting the flow splitting results of the network with the optimal ventilating equipments selected. In the past, the first step was relied on artificial decision-making. In order to design a common ventilation system, some ventilation experts were needed to participate or do some examinations. Even so, the design made was reasonable only for those experts. If there is a mistake in the first step, then even the followed 2 steps are best done, the losses are very difficult to retrieve. So that, the first step is very important. The development of expert systems provided an efficient means and tool for all engineering fields. This paper presents an expert system of selecting mine ventilation pattern and pit shaft arrangement. After testing many times, it is shown that the system can perform the first step of designing a mine ventilation system, and can help the experts doing their study works more efficiently.

Jan 1, 1991

By Park McLure, Paul Kunze

Abandoned underground mine workings have been regularly encountered in open pit mining excavations for many years, for the most part without many serious problems resulting. During the last several years however, some tragic occurrences and near misses have resulted when these old workings were intercepted. This paper will report on the problem as it relates to western open pit mining and will describe several techniques that can be used to identify problem areas before they are reached: Utilization of old maps and engineering data, long hole drilling and probing, and the use of subsurface investigation in the form of ground penetrating radar are the detection methods that will be discussed. The paper will describe some possible actions, once potential problem areas are identified. Drilling and blasting crews are usually exposed to the hazards involved when these situations arise because of their "on the ground" working environment. It is therefore appropriate that some of the best methods of dealing with these hazards once they are identified, seems to involve innovative and creative blast designs. The paper will discuss these approaches and describe an example of this aspect of the solution.

Jan 1, 1993