Search Documents

By W. C. Hagel, J. H. Westbrook

THERE has been a recent revival of interest in the intermetallic compound AgMg as an experimental material for study of the physical and chemical properties of simple ordered structures. Studies of mechanical behaviors,1-4 diffusion,5,6 and thermo-dynamic properties7'8 have been reported. In several of these studies, heat treatments have been carried out in argon-filled silica capsules at temperatures as high as 750°C with no apparent adverse effects. The present authors were, therefore, startled to discover in the course of some yet unpublished work, that gross melting of near-stoichio-metric AgMg compositions occurred in such samples more than 100 deg below their melting point of about 800°C. This note is to report a brief series of experiments carried out to establish the reason for this behavior. Gross errors in sample composition and failure of furnace temperature controls were quickly eliminated as causes of melting. The first tangible lead came from chemical analysis of an AgMg sample which had melted during treatment at 750°C. A silicon content of 3.3 wt pct was found. Since satisfactory analyses had been obtained on the original as-cast ingot, contamination by diffusion and/or reaction with the fused silica capsule seemed a distinct possibility. A perplexing fact, however, was the apparently capricious incidence of the effect. Not only was it previously unknown, even in the experience of the present authors; but, in the early part of the present study, melting sometimes occurred and sometimes not with specimens treated under constant conditions. Indeed, one sample successfully survived a 750°C heat treatment and yet melted completely during the course of a subsequent anneal in an identical capsule at a lower temperature. To obtain evidence that silicon contamination could lower the melting point to the extent observed, the following experiment was performed. A series of ternary alloys was made up with a stoichiometric AgMg base and containing 0.1, 0.2, 0.4, 1, 2, and 4 wt pct Si. Melting was done in MgO crucibles under a cover of argon gas. After holding 10 to 20 min in the temperature range 850° to 900°C, the alloys were allowed to solidify in the crucible and the temperature during cooling automatically recorded with a Pt/Pt-10 Rh thermocouple. Results from the cooling curves are shown in Fig. 1. Checks within 2 to 5C° were obtained upon repeated melting, cooling, and freezing. The whole series of cooling curves as well as metallographic examination of the melted alloys established that the AgMg rich portion of the AgMg-Si quasibinary is an eutectic-type system. The melting point of AgMg is lowered from approximately 820°C in the pure stoichiometric binary9 to about 710°C in the saturated intermetallic phase. Since second phase was observed in all samples on cooling to room temperature, the solid solubility of AgMg for silicon evidently falls rapidly with decreasing temperature as indicated schematically by the dashed solvus in Fig. 1. It is thus established that a silicon content

Jan 1, 1963

By E. Maxwell, C. J. Bechtoldt, H. C. Vacher

IN the course of an investigation of the properties of metals at low temperature there was occasion to determine the constitution of four iridium-osmium alloys. There is very little information in the literature1 on the constitution of synthetic Ir-0s alloys. Zvyagintzev' s has made a comprehensive study of different natural Ir-0s alloys and concludes that alloys containing more than 32 pct 0s have the close-packed hexagonal structure of osmium, whereas those containing less than 32 pct 0s have the face-centered cubic structure of iridium. The alloys studied in this work were prepared by the American Platinum Works, Newark, N. J., and were received in the form of fragments approximately 1.5 mm average diameter. The fragments had been obtained by crushing ingots made by fusing charges of iridium and osmium under an arc and air cooling. The ingots were not given a homogenizing heat treatment. Sample fragments Table I. Results of X-Roy Diffraction and Microscopic Examinations Phases Present as Determined by X-ray Diffraction Osmium Alloy Close- Iridium Face- Packed Centered Osmium, Iridium, Hexagonal Cubic Mlcro- WtPot Wt Pct Structure Structure scope 0 99.9 None Present 1 23.6 76.4 None Present 1 38.7 61.3 Present Present 2 59.4 40.6 Present Present 2 79.0 21.0 Present Not detected 2 99.9 0 Present None 1 Note: Chemical analyses of the iridium, osmium, and alloys were furnished by the American Platinum Works. of the iridium and osmium used in making the alloys also were included. Several fragments of each metal and alloy were examined microscopically and by X-ray diffraction. For the X-ray method the fragments were crushed further to pass a 270-mesh screen, then sealed in evacuated fused-silica tubes, heated to 1100°C for 18 hr, and allowed to cool in the furnace. Powder X-ray diffraction patterns were obtained from the annealed fragments by means of a Norelco camera having a diameter of 114 mm, and unfiltered cobaIt radiation. For the microscopic examination several fragments in the as-received condition were mounted in Melmac, (American Cyanamid Co.) and ground using the conventional series of abrasive papers. The polishing was done with 0-2 diamond abrasive on a Microcloth (Buehler Ltd.) lap, wet with xylene. After polishing, the surface was etched electrolytically in a 10 pct solution of chromic acid or in a 10 pct solution of potassium cyanide. Both reagents attacked the osmium-rich constituent, whereas the iridium constituent was attacked slightly by the chromic acid reagent and not noticeably by the potassium cyanide reagent. The results of the X-ray diffraction and microscopic examinations are summarized in Table I. Fig. 1 shows the microstructure of a 21 pct Ir-79 pct 0s alloy. The results indicate an appreciable solid-solu-bility range of osmium in iridium as was reported by Zvyagintzev.' The solid-solubility range of iridium in osmium is more restricted, apparently less than 21 pct Ir. This implies a large range of composition in which two phases can coexist that was not reported by Zvyagintzev.

Jan 1, 1955

By Francis Church Lincoln

"INTRODUCTION During the period from September 18 to November 27, 1944, the Bureau of Mines conducted an investigation and exploratory churn-drilling program in an area immediately north of the Crow Branch Diggings, a district lying approximately 2 1/2 miles southwest of the town of Livingston in Grant County, Wisconsin.The work was undertaken as part of a general Bureau of Mines investigation of the zinc-producing area of southwestern Wisconsin at a time when all effort was being made to increase the production of metals important to the Nation's war prrgram.Although no mining has been done in the district in recent years the Crow Branch Diggings were an important source of galena and may be found today in the dumps remaining from old surface-mining operations.The Bureau of Mines undertook an exploratory churn-drilling program on the northwestern projection of the general strike of the digging in a zone where subsurface,lead and zinc mineralization had been reported from drilling done in the early 1900's."

Feb 1, 1947

By Peter Lighthall

What is an engineering firm?s role? ? The ideal situation is a life of mine service alliance with the owner ? Engineering firms are long term custodians of information ? Maintain consistency with established closure objectives, adjust closure plans to meet changing situations and technologies ? Develop range of solutions and present owners with risk profile The mine closure planning process ?new mines ? For metal mining, geochemistry is the issue ? The planning process: ?Sampling ?Waste characterization ?ARD prediction ?ARD control strategies ?Life of mine waste management planning ?Assessment of residual impacts ?Development of strategies for dealing with residual impacts ?Estimate closure costs ?One time decommissioning and reclamation costs ?Ongoing treatment/maintenance costs

May 1, 2006

By Gordon Fletcher

Pacific Rim countries currently have plans to import about 100 Mt/a (110 million tpy) of steam coal by 1990. Due to its close proximity, Powder River Basin coals offer a long term economic and dependable source of supply to the Pacific Rim. In existing boilers, Powder River Basin coals can be blended with Australian, South African, or Canadian coals. For new units, Powder River Basin coals are very competitive on a total evaluated cost basis. The advantages of using Powder River Basin coal include: assurity of supply, consistent coal quality, stable labor force, and attractive mining economics. (NOTE: PAPER NOT RECEIVED IN TIME FOR PUBLICATION.)

Jan 1, 1982

By Kousuke Takahata, Hirofumi Yoshimura, Jun Nakahigashi

Studies of a protium treatment for grain refinement of a + ß type titanium alloy are reviewed and recent experimental results are introduced. Protium treatment consists of the following three processes: (1) protium absorption, (2) martensitic transformation and hot working, and (3) final treatment for protium desorption and recrystallization. A combination of these processes results in the ultra-fine grains of 0.3 to 0.5 µm in diameter with high angle boundaries. The ultra-fine-grained material exhibits superplastic elongation of over 9000%. Superplastic forming was successfully used to fabricate a denture base. These materials may be widely applicable as biomaterials in various medical industries.

Jan 1, 2004

CANADA, which appears to be growing into one big mining camp, may soon be the background for another impressively large iron ore development. And again it will be Fenimore Iron Mines who will be the motivating force. Dr. J. A. Retty, Fenimore president, who was one of the important figures in the development of Labrador iron deposits, predicts a great future for property on the west coast of Ungava Bay in deep northern area of New Quebec. Fenimore properties consist of a 200 sq mile concession in addition to several hundred claims over about 112 miles along the Labrador trough, mainly in the Ungava Bay region.

Jan 5, 1953

The October meeting of the Mining and Geological Society, Lehigh University, was held in the Eckley B. Coxe Mining Laboratory, and was called to order at 8:15 p. m., by President R. L. McCann. After the reading of the minutes of the previous meeting, a short business session was held, for the purpose of electing a Vice-President to succeed G. S. Borden, who has left college. Nominees for the office were: H. J. Sloman, P. S. Justice, L. Sargeant. Dr. F. F. Hintze, of the Geology Department, was elected a member of the Advisory Committee, which now consists of the President-

Jan 12, 1916

By Fred C. Bond

SIX years have passed since the last grindability table was published.1 In that time the list has been increased with many new tests, and the development of the new Third Theory of Comminution2 has made possible the reduction of all results to a consistent work index value. In this tabulation all grindability and crushability test results are given in terms of the work index, with formulas for reversion to the older units if desired. The average values for 57 different classes of materials are listed in Table I. The total number of work index values listed is 1211, and the overall average work index is 14.42.

Jan 3, 1953

By J. G. Peacey, P. Hancock, R. -Q. Li

A pyrometallurgical process for the direct recovery of zinc from zinc concentrates and zinc/iron residues has been proposed and tested extensively by Noranda. The process consists of smelting bone-dry zinc containing materials (sulfide concentrates and secondary zinc/iron materials) in a molten iron oxysulfide bath to volatilize metallic zinc into a SC^-free offgas. Sulfur contained in the feed materials is fixed as an iron oxysulfide matte for disposal. Thus, this process not only is capable of treating zinc sulfide concentrates and secondary zinc materials simultaneously, but also eliminates the need of sulfuric acid production. Detailed thermodynamic analysis and experimental test work are described in this paper.

Jan 1, 2000

By T. F. Torries

The primary criteria used by the mining industry to judge the merit of a project is internal rate of return (IRR) rather than net present value (NPV), although NPV is favored by academicians. This paper discusses the problems of IRR and NPV and compares the multigoal nature of the decision¬makers and their need for informa¬tion having the characteristics of NPV and IRR. The conclusions reached are that both NPV and IRR can be used for investment ranking, that NPV suffers the same multiple root problem as does IRR, and the use of conventional incremental IRR to reach NPV¬consistent project ranking is mis¬leading.

Jan 1, 1999

A new approach to strategic planning, the Life of Business Optimisation System (LOBOS) optimises production systems from the scale of stopes in a single mine to an entire business strategy consisting of multiple mines and products competing for capital and processing capacity. LOBOS has optimised cash flow for a wide variety of operations, including large metalliferous or coal mines and as an aid to high-level strategic business optimisation solution to multi-mine/processing/product complexes. This paper discusses the application of optimisation technology to strategic planning with an emphasis on project evaluation with examples on the application of LOBOS to a variety of recent projects.

Jan 1, 2007

By Launa Mallett, Charles Vaught, Michael J. Brnich, R. Lincoln Derick

After thoroughly covering the health and safety training subjects required under Title 30, Part 48, of the Code of Federal Regulations (CFR), mine operators often find themselves with little or no time left in the class schedule for other important topics. This paper discusses a technique developed in partnership with RAG Twenty mile Coal Co., Oak Creek, CO, for incorporating employee participation at all levels in fire prevention and safe equipment operation training outside of traditional classrooms. The process involves development of training modules consisting of short, 5- to 7-minute videotapes coupled with toolbox talks that ground the content of the videos within the context of a miner’s workplace.

Jan 1, 2002

By M. L. Smith

A new approach to strategic planning, the Life of Business Optimisation System (LOBOS) optimises production systems from the scale of stopes in a single mine to an entire business strategy consisting of multiple mines and products competing for capital and processing capacity. LOBOS has optimised cash flow for a wide variety of operations, including large metalliferous or coal mines and as an aid to high-level strategic business optimisation solution to multi-mine/processing/product complexes. This paper discusses the application of optimisation technology to strategic planning with an emphasis on project evaluation with examples on the application of LOBOS to a variety of recent projects.

Jan 1, 2007

By Ryan CG, Ramsden AR, Sie SH, French DH, Griffin WL

Proton microprobe and electron microprobe analysis are being used in combination for in situ determination of the trace element contents of oxide, sulphide and silicate minerals in a sample of the Merensky Reef. Initial results indicate that chromites contain only Ni, Zn, Ga, Zr ar d Nb. Platinum-group elements, if present, are at concentrations less than 2 to 6ppm. Ru, Rh and Pd are the only platinum group elements to be consistently detected in the sulphides. PentLindite is the most important host for these elements with the concentration of these elements being dependant upon the mineral association in which it occurs

Jan 1, 1989

By T. Tamagawa, I. Iwasaki, N. X. Fu, M. Kobayashi

A three-stage fluidizing-bed process consisting of chlorination, selective oxidation and sulfur chloride conversion was tested for processing chalcopyrite concentrate. It was found that the use of excess oxygen was essential for the stable operation of the oxidation reactor. The excess-oxygen gas inevitably causes the oxidation of the sulfide concentrate in the chlorination and sulfur chloride conversion reactors. A new flowsheet is proposed to separate the chlorination and selective oxidation steps with separate flow paths of the fluidizing gases, thereby, preventing the passage of excess-oxygen gas in the chlorination and sulfur chloride conversion reactors. The feasibility of the proposed flowsheet was demonstrated in a laboratoryscale fiuidizing bed setup.

Jan 1, 2002

By S. Chander, V. N. Sharma

Nickeliferous laterite ore from Sukinda, Orissa (India), consists of very fine particles agglomerated into larger aggregates. The ore is chemically and mineralogically complex and presents many characterization and beneficiation problems. In this study the results of a detailed investigation to characterize the ore by several techniques are discussed. Various techniques used for characterisation include elemental analysis, electron microscopy, electronspectroscopy for chemical analysis, x-ray and electron diffraction, differential thermal and thermogravimetric analyses, EDAX analysis, Mössbauer and infrared spectroscopy. Generally one method compliments the other and it is shown that a combination of several techniques is necessary to fully characterize the ore. The scope and limitations of the techniques are also discussed.

Jan 1, 1980

By J. B. Stockton, D. J. Robbins, E. T. Woodburn

Batch flotation data in an equilibrium cell show that beneficiation improves with froth drainage. The limiting lamella thickness in a well- drained 3-phase coal froth appears to be determined for ultra-fine particles (-45µm) by the d90 particle size. The froth stability is considered to depend on the existence of a very thin liquid film between the outer surfaces of the d90 particles and the bounding bubble interfaces of the lamella in which the particle is held. The dependence of the coalescence rate of bubbles in these froths on the residual surfactant concentration in the lamella liquid is then consistent with stability analyses for two-phase foams.

Jan 1, 1988

AXTAT is a computerised system developed by the Western Australian Department of Minerals and Energy in conjunction with the local mining industry for recording and retrieving information about fatalities and work related injuries. Since its inception, the system has gained considerable recognition by consistently demonstrating its usefulness as a tool, not only to the Department, but for the entire industry nationwide. AXTAT has played an important role in the continuous improvement process in management of occupational health and safety in the Western Australian mining industry with gains in both human and financial terms, by regularly providing timely and accurate statistical feedback on fatalities and lost time injuries to industry.

Jan 1, 1996

By Johnston RRM

There have been many published mathematical models that, to varying degrees of sophistication, attempt to describe dynamic thickener behaviour. CSIRO has undertaken to develop a model under industry sponsorship. Recently developed instruments such as the floc density analyser and natural gamma-ray gauge have enabled new data to be collected from plant thickeners for model validation and development. The principles behind the use of the natural gamma-ray gauge are described and the possibilities for its use as a control instrument in the bed have been examined. A simple nomograph illustrates how the gamma-ray gauge data can be used to predict steady state underflow consistency and bed Position.

Jan 1, 1991