Search Documents

By Gligorije Stankovic

This paper describes the fluo-solids roaster and acid plants at the new 40,000-TPY Trepca electrolytic zinc plant. The electrolytic zinc plant units were constructed to the design of Singmaster and Breyer, New York and began operation in mid-1967. The fluo-solids roaster plant, constructed according to the design of Dorr-Oliver, Paris, includes concentrate handling and storage facilities; two independent concentrate roasting circuits, each with a 110 to 155 TPD fluo-solids roaster; waste heat boilers; cyclones; electrostatic precipitators; calcine coolers; and calcine conveyors. The acid plant uses the "Petersen system" contact process. The plant has one acid circuit with a capacity of 230 tons of monohydrate per day. Gases for the acid plant are obtained from roasting zinc concentrates. When the roaster plant is operating at maximum capacity, excess SO2 is used in two other Petersen System circuits in the near vicinity.

Jan 1, 1970

By Foster Fraas

In this Bureau of Mines report, use of the photoemission of electrons to produce electric charges for the electrostatic separation of sonic dispersed minerals, which had previously been ground to pass a 43µ-opening sieve, is demonstrated. It appears that many of the oxides, carbonates, sulfides, and arsenides will respond to photoemission. Minerals least responsive are the oxides of silicon, the oxides of aluminum, and minerals that have a high concentration of these oxides. Although several synthetic ore mixtures did not yield to complete separation in a one-stage operation, it is probable that preliminary neutralization of the initial electric charges produced by powder dispersion will provide complete separation. That the separation can be carried out in air and without the use of reagents or heating, which are required in the present practice of electrostatically separating coarse granular feeds, is of special significance.

Jan 1, 1972

By Wolfgang Pietsch

Direct Reduced Iron is a product obtained during solid state reduction of iron oxides into metallic iron. General chemical and physical characteristics of all direct reduced iron materials result in a noticeable reoxidation tendency and a relatively low ignition temperature. As most of the chemical reactions are exothermic, normally heating occurs and if water is present hydrogen evolves. Dry direct reduced iron deactivates quickly in air but is still reactive if it comes into contact with moisture. Because of these characteristics, special requirements are necessary for safe storage, shipment, and handling. In an effort to improve this situation passivation techniques were and still are being developed. The paper discusses the properties of direct reduced iron, presents past experience with storage, shipment, and handling of MIDREX® Iron, a direct reduced iron material produced in the MIDREX® Direct Reduction Process, and evaluates benefits derived from different passivation techniques.

Jan 1, 1978

By Manuel Gomez

A general prediction model for the Hardgrove grindability index was constructed from 735 coal samples using the proximate analysis, heating value, and sulfur content. The coals used to develop the general model ranged in volatile matter from 12.8 to 49.2 percent, dry basis, and had grindability indexes ranging from 35 to 121. A restricted model applicable to bituminous coals having grindabilities in the 40 to 110 range was developed from the proximate analysis and the petrographic composition of the coal. The prediction of coal grindability within a single seam was also investigated. The results reported support the belief that mechanical properties of the coal are related to both chemical and petrographic factors of the coal. The mechanical properties of coal may be forecast in advance of mining because the variables used as input to the prediction models can be measured from drill core samples collected during exploration.

Jan 1, 1970

By T. Negeri, A. O. Orumwense

Microwave pretreatment is one of the emerging technologies which have been reported as having potential economic benefits for the processing of amenable ores. The application of microwave pretreatment to the processing of refractory and finely disseminated ores is of great interest as the technology can potentially reduce high comminution costs and improve mineral liberation. Sized ore samples were subjected to microwave irradiation at power levels varying from 1 to 5 kW over exposure times of between 1 and 6minutes in order to determine the influence of heating rate on mineral transformation, ground product size distribution and mineral liberation. The microwave irradiated samples were ground and subsequently floated. A comparison is made with non-microwave treated samples. Flotation grade and recovery show a strong dependence on the microwave absorption characteristics of the mineral components of the ore, in the following decreasing order -sphalerite, galena, and lastly chalcopyrite.

Jan 1, 2003

By M. Isac, R. I. L. Guthrie, S. Ge

The Al-Mg-Sc-Zr alloys have shown exceptional potential as structural materials for transportation applications. These alloys have proved to be good candidates to be processed as thin strips via the Horizontal Single Belt Casting (HSBC) process. The HSBC process is a near-net-shape casting technology, which involves casting molten metal directly into thin strips, close to the final product thickness, at high cooling rates. It offers an efficient, economical and environmentally-friendly approach to the production of metal strips. Fluid mechanics and associated heat transfer are important aspects of any casting process, and the novel HSBC process is no exception. Three dimensional Computational Fluid Dynamics (CFD) simulations using ANSYS FLUENT 14.5 were performed, in order to assess the importance and effects of the various operational conditions of the HSBC process. This enabled process parameter optimization. Numerical predictions were validated against experimental casting results.

Jan 1, 2014

By Zheng Wei, Jian Cheni, Zhenliang Weng, Wei Liang, Hongbo Zhu, Jinhui Peng, Linqing Dai, Qianxu Ye

"By testing the dielectric constant and the dielectric loss factor of concentrated Dahongshan, mill scale, anthracite and light-burned dolomite in different frequency and temperature, and by studying the temperature-rising characteristics of the materials in the microwave field of 2.45GHz in frequency, the research in the paper shows that to reach at 1250°C under the same condition -2KW the microwave power and 30g the mass --the time concentrated Dahongshan takes is 330s, whereas the millscale is 855s and the anthracite is 820s. About the last one, the higher the temperature is, the stronger the absorptivity is. After the temperature has rose to 400°C, the anthracite's absorptivity increases dramatically. The result of the research would serve as the foundation of the further study on making direct reduced iron by microwave heating.1. IntroductionUnder the microwave fields, materials' dissipation of dielectric bodies would generate thermal effect. Therefore, the dielectric constant and the dielectric loss factor are closely related to materials' ability of absorbing microwave energy-the larger the dielectric constant and the dielectric loss factor are, the stronger the material's ability of absorbing microwave energy is, and the better the thermal effect would be[1-2]. In order to research how to make reduced iron from iron ore fines by microwave heating deeply and systematically, the test of raw materials' dielectric constants and dielectric loss factors are of the essence. What's more, because a mineral' conductivity is influenced by its components and crystal structure[3], it is necessary to study different materials' different temperature-rising characteristics; hence such studies would provide theoretical foundation of further research."

Jan 1, 2012

Discussion of the paper of HENRY M. HONE and ARTHUR G. LEVY, presented at the New York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 587 to 600. J. E. STEAD, Middlesbrough, England (communication to the Secretary*).-As I have not personally studied the question of quenched and distorted manganese steels I cannot give any information of my own on the subject. The question as to whether certain indications in strained manganese steel are "slip bands" or "twins" might be settled, I think, by heat tinting-a method I have applied with success to certain meteorites and other alpha irons in which there were undoubted twins. After polishing and very slightly etching with picric acid in alcohol, and then "heat tinting," the colors assumed by the twinned strata and the adjoining metal are different. The reason of this, as I have proved repeatedly, is that different faces of the iron crystals are differently attacked by oxidizing and other reagents, and consequently some of the faces take temper oxidation tints more rapidly than others. This simple method enables one to determine with certainty whether the "twins" are actually, twins and differently oriented from the bed in which they are found. After correspondence with Dr. Howe, I think we both agree that Neumann lines should not be called "lines" but "bands" or "strata," preferably the latter term, as I have found that they are more or less continuous throughout the crystals, and it would be just as improper to call the edges of cementite plate by the term "lines" as to call stratified twins by the same term.

Jan 5, 1915

Committee on Reduction and Refining of Copper............ 3 A.I.M.E. Officers and Directors.................... 4 Preface. By C. R. Kuzell....................... 7 Career and Achievements of James Douglas. By Arthur L. Walker. . 9 PAPERS Smelting 1. Reverberatory Smelting Practice History of Reverberatory Smelting in Montana, 1879-1933. By Frederick Laist..............................23 Reverberatory Smelting of Raw Concentrates at the International Smelter, Miami, Arizona. By P. D. I. Honeyman (With Discussion)...... 88 Development of Gun-feed Reverberatory Furnaces at Garfield Plant of American Smelting and Refining Company. By R. A. Wagstaff (With Discussion)........................99 An Experimental Combination of Shaft Roasting and Reverberatory Smelting. By Frederick Laist and J. P. Cooper (With Discussion).... 104 Forms of Copper Found in Reverberatory Slags. By Royal B. Jackman and Carle R. Hayward (With Discussion).............111 2. Converting Practice Development of Copper Converting at Butte and Anaconda. By William Kelly and Frederick Laist...................122 Developments in Converting Lead and Copper Matte at Tooele. By B. L. Sackett.............................132 Messina Stationary Basic Copper Converter. By R. G. Knickerbocker (With Discussion)........................140 Smelting Copper Concentrates in a Converter. By George E. Beavers. 149 Sulfuric Acid from Converter Gases. By George E. Beavers......151 Development of Monolithic Tamped Periclase Converter Linings at United Verde Copper Company Smelter. By F. H. Parsons (With Discussion) . 153 3. Descriptions of Plants The Noranda Smelter. By W. B. Boggs and J. N. Anderson......165 Smelting Operations at Roan Antelope Copper Mines, Limited. By Charles R. Wraith.......................202 4. Waste-heat Boiler Practice Copper-refinery Waste-heat Boilers at Great Falls Reduction Department, Anaconda Copper Mining Company. By E. S. Bardwell......225

Jan 1, 1934

Coal slurry pumping was introduced into the U.K. in 1973. Gateside packs were prepared in areas of containment using R.O.M. coal and a special fast setting cement. The packs restricted roadway convergence and moderated spontaneous combustion risks, but costs were high and alternptives were sought. A similar system using OPC and an accelerator had limited success. Much more successful was the Aquapack process which used dilute slurries of a special OPC based cement and an accelerator based on sodium carbonate and bentonite pumped simultaneously into la fabric packbag. The Tekpak system using HAC and a much modified calcium sulphate mixture superceded Aquapack on the grounds of improved cement pumping life lower alkalinity and lower costs. A further modification of this system gave a cement with a 24 hour pumping life thus obviating flushing out pipe ranges except at the week-ends, improved packbags also increased the efficiency of the process. The hazard of spontaneous combustion can be inhibited if air supply channels across the waste can be located and plugged. Using gas samples from pack pipes to locate the heating and injecting a special grout, formulated from bentonite, sodium silicate and thixotroping agents. into the waste on the intake road has proved a successful method of controlling heatings. Mine' roadway and face cavities are being safely and successfully filled with cementitious foams produced in a novel placer machine. The foams are based on fast setting cements with specialised foaming agents. Up to 13 cu. metres per hour of fast setting thixotropic foams can be produced and their use is now widespread throughout U.K. coal mines.

Jan 1, 1986

By Mark Zablocki, Dakarai McCoy

Ground vibrations are an unavoidable effect of driving piles and may pose a risk to nearby infrastructure and the comfort of adjacent occupants. Driven-pile-induced ground vibrations are known to vary widely based on ground conditions, pile material, and installation means and methods. A monitoring sensor to record ground vibrations during pile driving is necessary for understanding potential impacts to sensitive infrastructure and should be considered when implementing a monitoring program anticipating ground vibrations. The implementation of a vibration monitoring program historically relies on experiential-based decision-making, which may result in the costly vibration monitoring of low-risk infrastructure. Prior understanding of anticipated ground vibrations is necessary to create an appropriate monitoring program. A framework is proposed for organizing data from past monitoring programs and quantifying the anticipated risk of driven-pile-induced vibrations. An example of risk quantification from data imported to ]a cloud database is presented by comparing driven steel H-pile and prestressed precast concrete vibration monitoring measured and collected by Haley & Aldrich between 2010 and 2020. The methods presented within the example can be applied to quantify a first order approximation of risk for ground vibrations at proposed driven pile sites based on the measured performance of previous sites with similar ground characteristics and pile installation methods. The presented novel data managements tools allow for a quick aggregation of vibration data with similar site conditions.

Sep 8, 2021

By D. L. Kuck

Water ice pillars far underground mine roof support can be frozen and/or maintained and/or melted on demand. The system to do this consists of a refrigeration brine chiller, brine circulation system and disposable plastic containers. Fusion expansion, resilience to dynamic loads, plastic deformation under stress, and non-contamination of coal or ore are unique properties of ice. Lower labor and material costs are economic advantages of ice far mine structural support. Ice brattices can become ice pillars on retreat. For safety, ice pillars can be placed (by remote control, if necessary) in hazardous sites without human entry.

Jan 1, 1988

By Frank C. Greene

The year 1941 was uneventful in oil and gas development in Missouri. No new pools were opened and several areas with promising structures, in the northwestern part of the state, were disappointing when drilled. In looking for an explanation of these failures, it is suggested that it will be necessary to find areas in which the lower beds of the Mississippian are upfolded, in order to obtain production in northwestern Missouri. To do this, geophysical exploration or test drilling far enough into the Mississippian beds to get cores or cuttings of definitely established age appear to be the best methods. Although not leading to new production, drilling in Missouri established two new state records, one for depth and another for the amount of rotary drilling. An important well† in sec. 24, T. 19 N., R. 11 E., Pemiscot County, in the southeastern corner of the state, was drilled with a rotary to 4740 ft., several hundred feet deeper than any previous hole. The total footage drilled by rotary rigs of various types was 31,135 ft. and that by cable tools, 29,166 feet. The total number of completions was 85, of which 18 were gas wells with an initial open-flow capacity of 12,528,000 cu. ft., and 67 were dry holes. Of the latter, 19 were drilled into Mississippian or older formations. Table I gives a summary of activities by counties.

Jan 1, 1942

By Frank C. Greene

The year 1941 was uneventful in oil and gas development in Missouri. No new pools were opened and several areas with promising structures, in the northwestern part of the state, were disappointing when drilled. In looking for an explanation of these failures, it is suggested that it will be necessary to find areas in which the lower beds of the Mississippian are upfolded, in order to obtain production in northwestern Missouri. To do this, geophysical exploration or test drilling far enough into the Mississippian beds to get cores or cuttings of definitely established age appear to be the best methods. Although not leading to new production, drilling in Missouri established two new state records, one for depth and another for the amount of rotary drilling. An important well† in sec. 24, T. 19 N., R. 11 E., Pemiscot County, in the southeastern corner of the state, was drilled with a rotary to 4740 ft., several hundred feet deeper than any previous hole. The total footage drilled by rotary rigs of various types was 31,135 ft. and that by cable tools, 29,166 feet. The total number of completions was 85, of which 18 were gas wells with an initial open-flow capacity of 12,528,000 cu. ft., and 67 were dry holes. Of the latter, 19 were drilled into Mississippian or older formations. Table I gives a summary of activities by counties.

Jan 1, 1942

New York, March 18, 1913. MR. CHARLES F. RA ND, President, New YORK, MARCH American Institute of Mining Engineers. Dear Sir: In connection with the official notice of Dr. Raymond's unanimous election by the Directors as Secretary Emeritus, we wish to place upon record certain statements concerning his services to the Institute which we think have not been published., and may not be generally known to the majority of our fellow-members. When the Institute was formed in 1871, Dr. Raymond acted as Secretary of the Founders' Meeting, and became the first Vice-President of the Institute, and, by request of the aged and beloved David Thomas, who was the first President of the Institute, Dr. Raymond discharged all the duties of the office of President, to which he was later formally elected in 1872, and which lip held for three years. During that time, he visited Europe, and through his acquaintance and reputation abroad, established those international relations of the Institute which proved so important in later years. He also enlisted the support of the mining engineers and metallurgists of the Pacific Slope, who would not otherwise have been disposed to join a society originating in the East. And for twelve years he attended; at his own expense, nearly every meeting of the Institute, wherever held, giving to it without remuneration his best service, and sacrificing for it many professional and private interests.

Jan 4, 1913

By P J. A Lever

This paper presents details of CRC MiningÆs work with waterjet assisted blasthole drilling. The objective of this work was to investigate techniques that reduce the cost and increase the productivity of blasthole drilling. The focus is on a technology that uses a high pressure waterjet to assist the conventional rotary rock cutting action of a tricone drill bit. The potential benefits of this technique are increased productivity, reduced drill bit wear and reduced hole deviation and hence improved quality of drilling. This paper describes the results of a laboratory based experimental program comparing conventional tri-cone drilling performance to the proposed waterjet assisted approach. Additionally, work has been completed looking at the more practical issues around the collection and sampling of drill cuttings and water recovery (recycling) when drilling with a waterjet. These studies have demonstrated that waterjet assisted drilling can significantly increase the rate of penetration over conventional rotary drilling. For the best-case experimental result, the relative improvement was over 40 per cent. More importantly, it is a starting point for examining alternative uses of the additional drill productivity obtained from waterjet assisted drilling. For example, increased drill productivity could be used to improve rock fragmentation by drilling a tighter blasthole pattern in the same time period. an existing drill fleet, then the drill fleet size could be reduced, or improved rock fragmentation could be achieved by drilling a tighter blasthole pattern within the same time period.

Jan 1, 2004

By Pertti Pekkala

Outokumpu has 25 years of experience in the SX area. The development of the solvent extraction plants responds to an ever increasing demand for lower operational costs wd for adaptability to process disturbances with minimized risks. In this paper the features of the VSF ("Vertical Smooth Flow") SX technology are described, such as the separated pumping and mixing, the homogenous gentle mixing, the droplet coalescence and the ultra pure settling. A major advantage of the mixing technology is the high stage efficiency of above 99 per cent. The connection between this and some features of the settler front section is clarified. The present design of VSF plants is based on experience of existing operations at, for example, Zaldivar, Radomiro, Morenci, Kokkola and Harjavalta. These production plants cover a unit capacity range of 60 to 3,600 m3/h expressed as a total flow. It is evident that there are no restrictive factors to increase the total flow up to 5,000-6,000 m3/h by introducing the VSF technology. The copper SX technology has a long history reflecting many individual features of the separate copper SX plants. Still it is necessary to verify all actual running parameters by pilot tests taking into account impurities, chemicals used etc. The design of SX plants is not only about the delivery of equipment but also a process concept, and it is best tailor-made and adapted to specific local requirements.

Jan 1, 1999

By D. E. Munson, H. J. Sutherland

Empirical methods for describing the shape of the subsidence trough over coal mines in Europe are tested against field measurements of subsidence over longwall panels in the United States. The graphical methods developed by the National Coal Board in the United Kingdom do not correlate well with the U.S. measurements; however, the profile functions typically used on the Continent give quite acceptable fits to the data. In the case of two longwall panels mined at Old Ben No. 24 in Illinois, a trigonometric profile function appears the best choice; in the case of two longwall panels mined at York Canyon in New Mexico, an error integral function is somewhat superior. Analyses of subsidence development curves show that rate effects occur. A comparison of fitting parameters establish influence functions as an important methodology for future analysis. In conjunction with the evaluation of empirical methods, an analytic model based on material failure and bulking was developed. A key element of the model is the void-volume distribution function which establishes a mechanism for transfer of significant amounts of the mined volume to the surface. Preliminary calculations demonstrate the features of the model and illustrate close correlation to physical observations in the field. Moreover, centrifuge models simulating the subsidence process have been used successfully to demonstrate the dominant or key failure modes necessary to the analytic model. General features of the centrifuge simulations and model calculations correlate well.

Jan 1, 1982

By G. R. Hopkins, E. W. COCHRANE

According to reports received by the United States Bureau of Mines , Department of Commerce , as of January 1 , 1930 , there were 412 completed refineries in the United States with a daily crude oil capacity of 3,755,585 barrels . This compares with 413 refineries of 3,509,540 barrels capacity on January 1 , 1929 , which indicates that whereas the number of refineries was practically unchanged , the total capacity increased 8 per cent during the past year . Of the completed plants as of January 1 , 1930 , 358 plants , of 3,634,825 barrels total capacity , were operating and 54 , with a capacity of 130,760 barrels , were shut down . Compared with a year ago , this indicates a decline in the percentage of the total refinery capacity that is inoperative . There has been a decided decrease in the number of shut-down plants since 1924 and 1925 , when one plant in every three was inoperative . Many of the inoperative plants of 1924 and 1925 were constructed soon after the boom times of 1920. Some of these were operated for a time but were unable to show a profit during 1923 and 1924 , when an overproduction of crude petroleum was accompanied by demoralized markets for refined products . Prices for refined products improved in 1925 and 1926 , but only a comparatively few of the shut -down plants , then partly obsolete , were able to obtain or renew their crude connections and compete successfully with the larger , more firmly established refineries . After five years or more of continuous idleness , a refinery would be rendered practically useless through corrosion and obsolescence . Consequently , most plants now being carried as " shut -down " have operated intermittently since 1923 . struction . A material change occurred in 1929 in the matter of plants under con- On January 1 , 1929 , there were 14 plants under construction , with a potential capacity of 99,000 barrels per day , whereas on January 1 , 1930 , there were only eight plants of 37,200 barrels capacity being built . This decline was due to the fact that the construction program in west Texas , which was at or near its height on January 1 , 1929 , was completed prior to January 1 , 1930 .

Apr 1, 1930

By Meyer C. F

The increasing use of continuous miners in the extraction of high coal seams has amplified the need for enhanced ventilation systems in the headings. Owing to larger face dimensions and higher production rates, more ventilating air is required to effectively dilute liberated methane to acceptable concentrations. However, the increased air quantities raise and entrain greater amounts of dust, to which the operator is subjected. Various methods (eg sprayfans, on-board scrubbers and jet fans) are used in various configurations and combinations to ventilate the headings. These arrangements generally result in a complex air flow pattern, which complicates achieving an optimum balance between diluting methane and minimising dust capture. In order to cost effectively investigate and propose solutions to this problem for the South African coal mining industry, the Division of Mining Technology has embarked on an extensive work program to evaluate various ventilation methods presently in use. Four currently generic ventilation patterns in various heading scenarios have been simulated using the Computational Fluid Dynamics (CFD) computer program. Evaluating these outputs against a predetermined set of criteria allows the best system for a particular situation to be chosen. The program also facilitates fine-tuning of an adopted system without incurring the cost and inconvenience of doing such tests in situ. This process not only provides solutions at significantly reduced costs, but also yields deeper insights into the factors affecting heading ventilation than hitherto possible.

Jan 1, 1995