Search Documents

By Peter K. Achireko, Samuel Frimpong

Design and optimization of open pit limits are of paramount importance because they provide information for evaluating the economic potential of a mineral deposit and for developing short and long range mine plans. Many algorithms and their modifications have been used to design and optimize open pit limits. These algorithms have provided mine planning engineers with pertinent information in designing, optimizing and extracting ore reserves by open pit technology. However, they do not address the random field properties associated with the ore grades and reserves and commodity prices, and thus, fail to yield the truly optimized pit limits in any time horizon. In this paper, a new algorithm, MCSIMFNN, which overcomes these limitations is proposed and used to optimize open pit limits. The random field properties of the ore grade and reserves have been modelled using the modified conditional simulation based on the best linear unbiased estimation and local average subdivision techniques. Artificial neural networks are used to classify the blocks into classes based on their conditioned values. The error back propagation algorithm, in the neural networks, is used to optimize the pit limits by minimizing the desired and actual outputs error in a multi- layer perceptron under the pit wall slope constraints. The optimized pit value obtained by this algorithm has been compared to that from the Lerchs-Grossman's algorithm in a case study. The results are the same, but in random multivariable states, the MCSI MFNN algorithm is the most suitable for pit optimization. The method is also fast since it mimics the operation of the brain in the solution of the pit optimization problem.

Jan 1, 1996

By Gustavo G. Pilger, Jair C. Koppe, João Felipe C. L. Costa

Information for mine planning requires to be close spaced, if compared to the grid used for exploration and resource assessment. The additional samples collected during quasi-mining are frequently located in the same pattern of the original diamond drill holes net but closer spaced. This procedure is not the best in mathematical sense for selecting a location. The impact of an additional information to reduce the uncertainty about the parameter been modelled is not the same everywhere within the deposit. Some locations are more sensitive in reducing the local and global uncertainty than others. This study introduces a methodology to select additional sample locations based on stochastic simulation. The procedure takes into account data variability and their spatial location. Multiple equally probable models representing a geological attribute are generated via geostatistical simulation. These models share basically the same histogram and the same variogram obtained from the original dataset. At each block belonging to the model a value is obtained from the n simulations and their combination allows one to access local variability. Variability is measured using an uncertainty index proposed. This index was used to map zones of high variability. A value extracted from a given simulation is added to the original dataset from a zone identified as erratic in the previous maps. The process of adding samples and simulation is repeated and the benefit of the additional sample is evaluated. The contribution of an extra sample was evaluated locally, globally and in terms of variation in total measured resources. The procedure showed to be robust and theoretically sound, mapping zones where the additional information is most beneficial. A case study using coal seam thickness illustrates the method.

Jan 1, 2002

By J. H. Archibald

"This paper describes the use of vector analysis for determining the intersection of mineral deposit veins. The mathematical evolution of the analysis is outlined.IntroductionMany mineral deposits can be characterized by sets of intersecting veins. Often a vein will have a steep dip and may intersect with another similar vein. Finding the intersections of these veins is usually done by graphical means. Structural geologists, by the methods of descriptive geometry, can usual ly predict where intersections of veins will occur. This method normally requires accurate drafting and layout of the problem and does not always lend itself to solution in the field.Another method for solving this problem involves the use of vector analysis, which is easily adapted to hand-held programmable calculators. It is assumed at the outset that the reader is familiar with the dot and cross products used in vector analysis. Two excellent references are cited at the end of this note for convenience.A plane, in general, is defined by three points. The points of interest here are the points where three vertical drillholes penetrate the vein, or plane, in question. The elevations of these three points are best referred to sea level. This requires knowing the elevation of the collar of the drillhole above sea level and the drillhole depth from the collar to the vein. The elevation of the intersection point is then found by subtracting the hole depth from the collar elevation. These three points now define the plane of the vein. A similar set of three points will define a second vein, and it is our object to show analytically their intersection if it exists."

Jan 1, 1983

By T. Vasilos, J. T. Smith

THE mechanism of pressure sintering, or hot pressing, for ceramic materials, has been investigated by several researchers.1-8 Plastic flow has been suggested as the rate-determining mech-anism1,2 while grain boundary sliding3,4 and fragmentation processess have been found controlling in other studies. Vasilos and Spriggs5,6 have reported that pressure sintering occurs by a diffusion-controlled mechanism. For the pressure sintering of metals, investigations with lead7 and with tin6 have not identified the operative mechanism during consolidation of these powders. This note reports the results of a pressure sintering study initiated to determine the mechanism controlling the densification of spherical copper powder. Temperatures of 300°, 400°, 500°, and 600°C at 2500, 5000, 7500, and 10,000 psi pressures were investigated. The copper powder for this study was obtained from Metals Disintegrating Co., Elizabeth, N.J. The minimum purity was reported to be 99.9 pct. The powder size was -325 mesh and a lineal analysis showed the average size to be less than 1 p. An alumina die body and punches were employed. Graphite spacers were placed between the copper powder and the punches before pressing. It was expected that the graphite would form carbon monoxide with any entrapped air and form a reducing atmosphere within the die cavity. This condition was generally realized during pressing although a minor amount of oxidation occurred at 500" and 600°C. The oxide particles were located randomly in the pressed samples and were not considered to influence the densification process. Calibration tests showed the temperature of the copper pellet to be about 20°C less than the die wall temperature, probably resulting from heat losses through the punches. This difference was compensated during the experimental pressing operations. The hot pressing equipment employed for this work has been described by Spriggs et a1.9 and was calibrated with a Baldwin-Lima-Hamilton load cell. Travel of the punches was monitored with a dial indicator showing increments of travel to 0.0005 in. Relative density was calculated at selected time intervals for a known copper weight, punch travel, and die diameter. The accuracy of this calculation was *1 pct. Average grain size after hot pressing was obtained by lineal analysis. Typical densification curves are presented in Fig. 1 and Fig. 2 where relative density is plotted vs log time as a function of applied pressure for the 300" and 600°C pressure sintering temperatures, respectively. The curves for 400" and 500°C were similar to those at 300°C and consequently are not shown. The curves at 300°C as well as 400" and 500°C do not show an end-point or limiting density for a particular applied pressure. At 600°C, a density in excess of 95 pct of theoretical has been reached such that further densification is extremely slow for the 5000, 7500, and 10,000 psi pressures. It is suggested that further densification at these pressure levels may be retarded or prevented by discontinuous grain growth, by entrapped gases, and by other microstructural limitations as described by Cob1e.10 The curve for 2500 psi hot pressing pressure is a straight line over the time interval although a slight change in slope may be occurring at the last time intervals. The plastic flow models,1,2 derived for hot pressing, predict the existence of an end-point (or limiting) density dependent on the yield point of the material at the temperature of interest. The yield stress of copper at a 0.005 strain level has been

Jan 1, 1965

Shoveling ore cost so much at Tyrone during the year 1917 that it was deemed advisable to conduct tests to see where the fault lay. These tests were in the nature of time studies and extended over a period of very nearly a year. No data were available on this work to supply a starting point, so it was necessary to begin in a very elementary way, to find out the capacity of the average Mexican laborer. To' obtain a basis for comparison, it was necessary to determine the capacity of various types and sizes of shovels, so as to know whether the 21-1b. (9.5-kg.) load was the best load underground as well as on surface. A list of essential factors influencing shoveling was also made out during the course of a short series of preliminary time studies, and the motions involved in shoveling were analyzed and subdivided for convenience in studying. The necessary forms and record sheets were also decided upon at this time. A second short series of tests was then conducted on the surface, so as to be able to estimate the negative effects of underground work on the shovelers, and to minimize, as far as possible, the need for studying obviously poor types and sizes of shovels under the difficult conditions to be encountered in the mine. The test work underground consumed by far the greater proportion of the time and was divided into three series: Shoveling directly into a chute; shoveling into a wheelbarrow and tramming to a chute; and shoveling into a car and tramming to a chute. In each series the following points were determined for various lengths of time worked: Number of shovelfuls handled per minute, effect of distance thrown on shoveling speed, amount of rest required, amount of time consumed in tramming and dumping, proportion of working day occupied in shoveling, total tonnage handled during various working periods, effect of distance on tonnage handled during the day.

Jan 2, 1919

By Y Potvin

Risk assessment in the mining industry is currently a topic of great interest with risk methodologies being increasingly applied beyond the traditional areas of finance and feasibility to analyses of risks due to various physical hazards including chemical, electrical, mechanical and geotechnical sources. The application of risk analysis and evaluation techniques to the management of personnel safety is being promoted by both industry and regulators but, particularly for geotechnical hazards, often there are inadequate databases for a meaningful quantitative calculation of risk. In Western Australia over the decade 1987 - 1997, the annual fatality rate for underground mining has averaged at approximately 1.3 in 1000 employees with rockfalls/rockbursts accounting for over half of these deaths (Prevention of Mining Fatalities Taskforce, 1997). Recent improvements have been made since this time, perhaps halving the annual fatality rate, mainly due to industry improving ground control measures and implementing various recommendations from the Prevention of Mining Fatalities Taskforce (1997). However there still remain a large number of unknowns when trying to address the complex area of geotechnical risk in mining. Risk calculations require information about the source of the hazard, the people or assets exposed to the hazard (the æelements at riskÆ) and the effects on these vulnerable elements if the hazard actually occurs (the potential consequences). To date, little information has been available on the exposure of mining personnel and equipment to underground hazards other than occupational safety studies on chemicals, heat, dust, etc. This paper concentrates on underground geotechnical risks and presents a data collection and rating system for the exposure of both the underground workforce and equipment to rockfalls and rockbursts. The methodology considers exposure times, personnel protection levels and hazard proximities to give exposure ratings for the major underground mining activities and hence rate different locations within a mine. This exposure methodology is then applied to the workforce and production/ development cycles in an actual WA underground mine, creating a snapshot map of differing levels of personnel exposure across the mine.

Jan 1, 2003

By W. A. Wood, H. L. Wain, R. I. Garrod

The mechanical behavior of recrystallized chromil~m of high purity has been studied, principally in torsion and to a lesser extent in tension, at temperatures between —196oand 350oC. Depending upon the conditions of test, the material may show brittle or ductile behavior or an intermediate or subduc-tile state having some of the characteristics of each. This latter state existed at temperatures between approximately ±50°C and was characterized by a) extensive creep at stresses well below the normal fracture stress, b) nonelastic loading/unloading effects during creep, c) strain softening under cyclic loading, and d) final failure of a brittle type. Suggestions are made on the dislocation processes and interactions which give rise to subductile behavior The ductile-brittle transition in bee metals has been studied mainly by tension and bend tests. These methods, however, favor crack propagation which may follow too closely on initiation for detailed study of the transition itself. For work of this nature, therefore, other modes of deformation less favorable to crack propagation may be preferable. This paper describes a study of the ductile-brittle transition in chromium which is based mainly on torsional testing although a few subsidiary experiments were made in tension. It appears to reveal at the transition an intermediate state that cannot properly be described as either brittle or ductile. Torsional tests on chromium have been made by other workers1 but not, as here, primarily for study of this intermediate state. EXPERIMENTAL The chromium, in the form of swaged rod, was prepared by techniques already described.' The particular material used was one in which the main impurities were 0.03 wt pet 0 and 0.006 wt pet N and one in which transition from ductile to brittle states in torsion conveniently fell at about room temperature. For torsion, test specimens were from 5/16-in.-diam rod to provide test portions 1-1/4 in. long by 7/32 in. diam, a twist of 1 deg thereby corresponding throughout this paper to 0.0015 surface shear. The specimens before test were annealed for 2 hr at 1200°C in vacuo, which left them with a re-crystallized grain size of about 0.01 mm, and then electropolished. They were tested under dead-weight loading in an apparatus in which they could be surrounded by a furnace or cooling chamber, tests in practice being made at various temperatures between -196" and +350°C. For tension tests, cylindrical specimens were prepared in a similar manner and tested at room temperature under dead-weight loading. RESULTS (TORSION) Subductile State. The state described above as intermediate between brittle and ductile may be perhaps best defined by reference to torque/twist curves at various temperatures. These are grouped in Fig. 1. Below about -50°C the material was brittle, in the sense that it exhibited little plastic deformation under stress and fractured by cleavage along planes of maximum resolved tension, which in torsion produces the well-known helical type of fracture. The deformation is typified by the curves for -196" and -150°C in Fig. 1; it shows a slight but progressive deviation from linearity above a certain torque, here about 50 lb-in., until fracture occurs at about 95 lb-in. A feature to which it is desired specially to call attention is that under none of the loads did the specimens show significant creep.

Jan 1, 1964

By R. E. Phillips, L. A. Cramer, R. T. Jones

Atomaer (Pty) Ltd is a technology-driven company with interests in Western Australian nickel. Atomaer (RSA) Pty Ltd is a process technology company operating in Southern Africa. It is a subsidiary of Atomaer Holdings Pty Limited (Atomaer), which has operating companies in Australia, Africa, South America, and Europe. In addition, Atomaer has substantial shareholdings in Braemore Resources Plc, a nickel company with interests in sulphide nickel projects in Western Australia and Southern Africa listed on the Alternative Investment Market of London Stock Exchange (AIM); Mintails Limited, a gold company with interests in gold operations in South Africa listed on the Australia Stock Exchange; and Brinkley Mining Plc, a uranium company with interests in Southern Africa listed on the AIM. Independence Platinum Limited (IPt) has been formed by Atomaer to undertake the commercial development and exploitation of Mintek's ConRoast technology with the strategic objective of providing independent smelting and refining facilities with lower capital and operating costs for the treatment and processing of platinum concentrates, including those with high chrome and/or nickel and/or low platinum group metal values, for the development of platinum projects by junior resource companies in South Africa. The platinum mines of South Africa have traditionally exploited the Merensky Reef of the Bushveld Complex for platinum production. However, the mining of this reef is reaching depths that require significant vertical shaft systems and costly refrigeration for access to the ore bodies at deeper levels. In the past decade, all of the platinum producers have begun to mine the UG2 reef because of its cheaper mining costs. UG2 ore usually has lower platinum group metal contents and higher chrome values. The new junior resource companies have gained access primarily to UG2 reefs. Consequently, platinum mining is becoming more UG2-based and the resulting concentrates contain high levels of chromitite. UG2 concentrates are difficult to smelt in the current six-in-line submerged arc furnaces, and this leads to increased capital and operating costs for those smelting operations. The platinum mines of South Africa produce the majority of the world's platinum metal used in automotive catalysts and jewellery. As the platinum market is forecast to grow at a healthy rate into the future, the SA producers Anglo Platinum, Impala, Lonmin, and Northam are planning to expand mining operations in the next decade. Furthermore, a number of smaller new producers who are accessing other mineral resources are entering the buoyant market and will produce platinum concentrates for purchase or toll treatment. Hence, a shortage in both smelting and refining capacities is anticipated. Further smelting and refining facilities independent of the major platinum producers will be required in South Africa by 2010. Mintek's ConRoast technology is best suited to fill the need to treat a high proportion of UG2 concentrates in a cost-effective and technically efficient manner. Atomaer base metals technology has been developed for rapid leaching of nickel and other base metals from alloy. Significant reductions in capital and operating costs are expected from the combination of the two advances in process technology compared with that installed at the existing smelters and refineries that were established over 20 years ago. Independence Platinum will be listed on AIM and the Johannesburg Stock Exchange (JSE) in 2007, and developed as an independent, vertically-integrated platinum company using its independent smelting and base metals refining facilities as a strategic platform to promote the development and mining of platinum projects by junior resource companies in South Africa through technical co-operation, strategic alliances, joint ventures, off-take, toll-refining, and marketing agreements.

Jan 1, 2006

By Ulf S. Landergren

Diffusion coefficients and marker movements have been determined in brass using welded couples. Three different concentration ranges were employed at 750°C, while a fourth concentration range was measured at 500°, 600°, 700°, and 800°C. Marker displacements toward and porosity development in the high zinc side of the couple were observed in all cases. The results were interpreted as favoring a vacancy diffusion mechanism. IN the large amount of diffusion literature which has accumulated during the past half century, very few experimental data have been presented on body-centered-cubic metallic phases. The impressive combination of experimental and theoretical studies which has given the vacancy mechanism a fairly secure position as the preferred mechanism for most face-centered-cubic metals has no counterpart for body-centered-cubic phases, although the theoretical picture seems to be in a better state than the experimental work. The attempts to select diffusion mechanisms by the theoretical calculation of the activation energy for the various conceivable unit diffusion processes and the energy of formation of the type of lattice defect required have been based on models of two kinds. The first kind utilizes potential functions fitted for certain properties of pure crystalline copper; the second kind is fitted for sodium. The latter is an example of an open metal in which the metallic ion is small compared with interatomic distance,&apos; while the former is characteristic of the larger class of metals in which the ions have diameters about as large as the interatomic distance. brass should resemble copper in this fundamental property. It should be evident that results on the mechanism of diffusion obtained for one of these classes need not necessarily apply to the other. Huntington and Seitz, using a model of the copper type, showed that the activation energies to be expected for interstitial migration or a two-atom direct interchange were much higher than that for vacancy diffusion. Zener pointed out that a four-atom ring rotation would involve an activation energy considerably lower than the two unlikely mechanisms although still higher than the vacancy mechanism in the face-centered-cubic structure. Furthermore, he argued, the four-atom rotation would be relatively easier in a body-centered-cubic lattice and might be competitive with the vacancy mechanism. Paneth showed that a body-centered-cubic crystal-like sodium could form interstitial defects of special type, called a crowdion, by crowding an extra atom into < 111 > directions where the defects would affect a line of about eight atoms. The defect was constrained to move along the defining line. Unlike the face-centered-cubic case, therefore, the theoretical calculations for the body-centered-cubic mechanism do not provide a very clear-cut answer, and the absence of adequate experimental studies is the more serious. This investigation was undertaken for the purpose of obtaining useful information on diffusion in body-centered-cubic phases. brass was chosen for several reasons: 1—the phase field is sufficiently wide at high temperatures to permit the use of diffusion couples with adequate concentration ranges for satisfactory chemical analysis, 2-—thermodynamic activity data are available for the calculation of mobilities from diffusion coefficients, 3—the phase is as close to the theoretical model of the copper -type on which the calculations have been done as any body-centered-cubic metallic phase is likely to be. Measurements of the movements (if found) of inert markers during the diffusion process would indicate that a vacancy or Or mechanism played a major role in diffusion in brass. If no marker movement should be found, a ring mechanism would be indicated but not assured. Experimental Procedure The alloys used in these experiments, listed in Table I with analyses, were supplied by the Naval Research Laboratory. They were from ingots of 3x3 in. cross-section, heated to 760°C, reduced under a

Jan 1, 1957

By d&apos, D. L. Guernsey, J. C. Entremont, John Chipman

The reaction of aluminum with oxygen in liquid iron has been studied at 1740° and 1910°C. Interaction coefficients are very much smaller than those previously published. The equilibrium constant falls within the approximate range of earlier experiments and calculations. It is now well established that the "deoxidation constant" for aluminum in liquid steel at normal steelmaking temperatures is extremely srnall. Thus at 1600 the product [% Al] is of the order of 10- 14. At this temperature, therefore, great experimental difficulties are encountered in any attempt to obtain a direct measure of the constant. If the aluminum content of the metal is high enough to permit accurate analytical determination, that of the oxygen is too low. If the oxygen content is high, the aluminum is below the limits of detection. Our best values of the constant have come, therefore, from indirect calculations or by extrapolation downward from observations at higher temperatures.. For their studies in the range 1695° to 1866°C, Gokcen and chipman&apos; restricted their aluminum concentrations to less than 0.06 pct. Oxygen analyses were made by the vacuum fusion method which appears to be dependable at these low aluminum concentrations. Experimental results, even at the highest temperature employed, are extremely sensitive to small errors in the analysis of either element. The slight change in the equilibrium constant with aluminum and oxygen concentration was utilized in the calculation of interaction coefficients expressing the effect of aluminum on the activity coefficient of oxygen and the reciprocal effect of oxygen on the activity coefficient of aluminum. The range of concentration, however, was so limited that only a rough value for the interaction coefficient could be obtained. This value was much more negative than that found for any other pair of reactants. In view of the very limited range of concentration employed, the reported values have always been regarded as very questionable. A redetermination was the object of the work reported here. EXPERIMENTAL METHOD At high aluminum concentrations, the vacuum fusion method is susceptible to grave error due to absorption of gas by aluminum distilled from the sample. Since it was desirable to extend the study to at least as much as 1 pct Al, another method for analysis was sought. In steels containing more than a few hundredths of a percent aluminum and no other deoxidizing element, it is safe to assume that

Jan 1, 1963

By S. K. Sharma

The Bureau of Mines&apos; rapid method of dewatering fine-particulate slurries uses extremely high molecular weight polymers. These polymers form large, strong flocs which can be dewatered by sieving or sedimentation. However, sometimes these flocs deteriorate rapidly if water is not removed immediately. During field tests, clay slurries have been encountered that could have been dewatered economically if it were not for the rapid floc deterioration. A kinetics study was conducted to determine the rate of kaolin-PED floc degradation in which polymer addition, to bring the flocs back to their original condition, was used to determine the extent of floc decay. Results showed that the amount of polymer added, to replace polymer lost by spreading, was less for the lower PEO concentrations. For this clay-polymer system, floc breakage as judged by polymer additions followed first order kinetics. It was also found that the addition of fluoride ion stabilized the kaolin flocs.

Jan 1, 1992

By Neal P. Cochran

It is always a pleasure for me to address a group of mining engineers. I am doubly grateful when I am allotted sufficient time to describe the total Office of Coal Research program. My remarks are directed to our total program but I trust you will all understand my emphasis of the utilization aspect of our activities since that is my portion of the program. From its inception, the Office of Coal Research has sought out creative ideas for improving our national use of coal by developing new uses, improved mining procedures, lower costs, and appropriate studies with respect to the resource itself. Quite early in the game, our Economics and Marketing Division contracted for studies with respect to New England export market, Western coal, and similar items. Our Mining and Preparation Division has successfully developed a packaged coal-fired boiler and has partially developed a packaged fluid-bed type boiler as well. Our Mining and Preparation Division is working in such diverse fields as treatment of sewage with coal and the separation of coal into distinct-petrographic constituents so that all fractions of the coal can be put to the best possible use. We would like to be doing more work on improved mining methods, better preparation techniques, and any other mining improvement that will benefit the industry and our program. The synthetic fuel plants I will describe later will operate seven days per week, 24 hours per day. We would like the mine to operate on this same sort of cycle and are prepared to support research that will lead to this.

Jan 1, 1970

By W. V. Swarzenski

In its, effort to combat waterlogging and coil salinity, the later and Soils Investigation Division of WAPDA (West Pakistan&apos;s Water and Power Development Authority) has carried out an extensive program of test drilling and water sampling, since 1954. Data collected during the past ten years have permitted the delineation of fresh and saline ground-water-zones in the Punjab Plain. Fresh ground water containing generally, less than 500 ppm (parts per million) of total dissolved solids is found in wide belts paralleling the major rivers and in other areas of fresh-water recharge. Locally, fresh ground water extends to depths of 1,500 feet and more. Saline ground water occurs downgradient from sources of recharge, particularly in the lower central parts of the interfluvial areas and, presumably, underlies most of the Punjab Plain. The ground waters of the Punjab are characterized by their evolution from calcium, magnesium bicarbonate waters, near sources of recharge, to waters containing a dominant proportion of sodium. The highly mineralized waters of the Punjab are generally of the sodium chloride type, whereas in Dera Ismail Khan District sodium sulfate waters predominate. The pattern of distribution of saline ground-water zones and the observed gradual increase in mineral content, downgradient from sources of recharge, can be explained best by a hypothesis stressing the processes of evaporation from the water table and solution of minerals within the alluvial aquifer.

Jan 1, 1967

By Harry Tufft

FOR many years the treatment of mine timbers with preservatives was confined to a few pioneer plants in the United States, and it is only in the past few years that the practice has grown appreciably. In a field study of the mine timber situation in Illinois, Pennsylvania, and further study of the situation in the country as a whole, I found that most mine operators did not keep records on mine timber that would afford the necessary data for determining the possible savings from preservative treatment. Some primary questions the mining engineer should be able to answer before making his decision on preservative treatment. for a particular mine are: (1) Quantity and cost of timber going into permanent workings annually; (2) quantity and cost of annual replacements due to decay; (3) life of untreated timber in different places; (4) desired life of timber. With the necessary facts in hand, he can then con-fidently select a method of treatment and preservative that is best suited to his needs. In former years when timber was cheap and an abundant supply could be had close at hand, as was the case in the majority of mining regions, the mine op-erator did not concern himself much except to see that enough was supplied to keep the workings safe. The cost figure for timber and labor, distributed to cost per ton of ore, was all the bookkeeping necessary. With present costs of timber, labor, and increasing length of haul to the mine, many operators are paying closer attention to timbering costs and studying them in. more detail. Some of the larger and more progressive opera-tions now keep detailed&apos; figures that give information on all phases of their timber problems. However, at the majority of mines the data available do not permit such analysis. Checks as to where the different con-signments are placed, the date of setting, and the period

Jan 6, 1927

By A. C. Lane

Relations de la profondeur de plissement avec la gravita-tion et la hauteur des montagnes dans les Alpes. Par A. Heim (Zurich) 50me Anniversaire, Livre Jubilaire Soc. Geol. De Belgique, Rome, Fascicule 1, 17 to 28. Measurements show a negative anomaly, less densities of .the material below sea level. The author expresses it in terms of the thickness of rocks of an arbitrary density, 2.4, which might be considered wanting. The accordant heights of the summits, the depths of the folds, the deficiency in .gravity, and denudation he finds to be connected. The Alps float on the lightness of the folds of "sal" of weight 2.6 to 2.75 plunged into the heavier "Sima" according to a for-mula: P = h (2.7/2.8-2.7) where - P is the depth of fold-ing below sea level; 2.7 is the weight of the material accu-mulated in folding; 2.8 is the weight of the material dis-placed by it; and h is the mean height of the mountainous regions. For instance, between the valley of Saar and the Val de Bagne in Valais the depth of the folds according to Ar-gand&apos;s profiles is between 30 and 40 kilometers. The loss of gravity has been estimated in this region as 1450 X 2.4 = 3480 in units of weight. Obviously errors in the densities would profoundly affect the estimates of the thickness of folding, but his depths of folds are obtained from sections, and from them he works back to the densities. Of course other densities might be placed in the formula. Zur Dichte bestimmung von Tonen. By J. Koenigsberger, Berg u. Hüttenmannisches Jahrbuch, 75, I. Discusses Dr. B. Wilser&apos;s investigations as to the best way of obtaining the weight of rocks per unit volume. The use of mercury for rocks affected by water as there recom-mended may easily give too large volumes unless 1 to 3 atm. pressure is used. Thick machine oil is recommended for large lumps of clay.

Jan 4, 1928

By B. M. Sadashiva Murthy

Increasing quantities of nutrients and pesticides in agricultural runoff in recent years has caused the more developed western nations to become concerned about diffuse agricultural pollution. Thus, the problem of diffuse pollution is of greater importance and concern for any integrated water quality management programme. The above mentioned sources and activities causing pollution to groundwater cannot be completely avoided. The best solution is to entail a firm understanding of the principles of solute transport through porous media. The complex factors that control the movement of contaminants in porous media and the resulting behavior of contaminant plume are usually intricate to assess because of interaction of many factors such as dispersion, advection, sorption, degradation, volatilization, etc. As accurate quantification of solute under field conditions is inherently difficult, the fate of nitrate and phosphate have been analyzed in laboratory column and channel studies. From the analysis of the breakthrough curves, the dispersion co-efficient for nitrates and phosphates through sandy soil was found to be 0.262 m2/d and 0.114 m2/d for column studies, 0.321 m2/d and 0.231 m2/d for channel studies respectively. The column studies revealed that the concentration of nitrates and phosphates increased steadily in the first few days (around 5 days) and then it increased rapidly after 8 to 10 days. However, it attained equilibrium after 20 days. Similarly, the channel studies revealed a steady increase in concentration of nitrates and phosphates in the first few days (1 to 2 days) and rapid increase up to 15 days and there after it attained equilibrium. In the study, one-dimensional analytical model has been developed which include the advection, dispersion, and a characteristic term called ?total elimination rate?. The comparative study of column and channel studies, and model output (in which the term total elimination rate ?K? is considered as zero) exhibited a variation of 30 to 50 % in leaching characteristics of pollutants (nitrates and phosphates).

Jan 1, 2008

By Abdurrahman Tosun

It is very important for after blasting processes that muck pile fragmentation is predicted and controlled during blasting. Therefore, a significant research effort has been devoted to the development of mathematical equations that predict the value of average muck pile fragmentation. The specific charge parameter used in all of these equations is determined as the ratio of the total mass of explosives used to break a volume of rock. The length of blast surface and the row number of the blasthole are ignored in the calculation of the specific charge. However, in a blasting operation, blasthole geometry may result in additional material being impacted by a blasthole. This is due to effect shares of in both end sides of blastholes and the back region of blasting surface. In this study, a total of 14 blast tests, 8 at the first quarry and 6 at the second quarry of the Bati Anadolu (Western Anatolia) Cement Factory, were performed. In each study area blast tests were designed in the same direction continuously to provide stable structural properties of the rock. Therefore muck pile fragmentation depended on only specific charge values for each blast tests. Specific charge values were calculated according to both an average blasthole and also the total volume of material occurred as a result of blasting for each blast tests. During loading until the end of blasted material the front, the back, the arm off and the bucket off pump hydraulic pressure values occurred in hydraulic pistons of the loader were determined with a lot of data received for each blast tests. After that the relationships between specific charges values obtained according to two different methods and hydraulic pressure values of the loader were established with two correlations. The relationships between specific charges values obtained according to the total volume of material occurred as a result of blasting and hydraulic pressure values of the loader occurred as the best results especially the blasting operations that have the total length of blasting surfaces are short.

Aug 1, 2013

Meeting, Aug. 20, 1913, B te, Montana, at 12.45 p.m.-On, the written request of 27 members of oft Institute residing in Montana, the Montana Local Section was established, and the following Committee was appointed by the President of the Institute to complete the organization : E. P. Mathewson, Chair pan; Frank M. Smith, Vice-Chairman; D. C. Bard, Secre-tary, Montana State School of Mines, Butte, Mont., Oscar Rohn, James L. Bruce. The President reported the appointment of a Committee on Mining Law, the names of whose officers and members are given on page xxxv of this Bulletin, and these appointments were approved. It was voted: That the Committee on dining Law be requested to establish a Sub-Committee on Censorship, a majority of whom shall be lawyers; and, further, that no paper on mining law be recommended for publication to the Committee on Papers and Publications, unless it is previously approved by the Sub-Committee on Censorship of the Committee on Mining Law. The President reported progress in the matter of co-operation between the Institute and the United States Bureau of Mines, through Committees of the Institute. The President reviewed the history of plans for a union or affiliation with the Mining and Metallurgical Society of America, and the following minute was then adopted : " The Board of Directors of the American Institute of Mining Engineers has carefully considered for several months the question of union or affiliation with the Mining and Metallurgical Society of America ; and, while at an earlier time and under other circumstances, such. a union might have been accomplished, yet under present circumstances the Directors of the Institute deem such union inexpedient. "While thanking the Mining and Metallurgical Society of America for its consideration of the matter, we believe that further discussion of the subject will serve no useful end, and we conclude it best that the Society and the Institute continue their useful functions and friendly relations side by side, as heretofore."

Jan 10, 1913

By K Dudley, D Readett

The design of entrainment control processes in copper SX plants has been studied by use of models based on achievable plant performance. A number of alternatives have been assessed for their suitability in minimising the transfer of deleterious species from PLS into the electrolyte. The position of the wash (scrub) stage in the circuit, either before or after the loaded organic tank, has been the subject of considerable debate. The modelling shows that at ænormalÆ entrainment levels, the performance of the circuits are very similar. However at high entrainment levels the selection of the wash after the loaded organic storage has significantly lower transfer of contaminants. When considering the inclusion of a loaded organic coalescer the results of the modelling again show that the best circuit has the loaded organic storage/coalescer before the wash stage. The overall control of EW contaminants includes both a wash stage and an EW bleed flow. The total water use for these two flows is shown to go through an absolute minimum. The minimum flow rate is not greatly dependant on the total entrainment from the SX settlers. This can be a useful operating strategy if the quantity of high quality water for make up is limited by the capacity of the water treatment plant (eg RO). However the minimum cost option is to maximise the flow of water to the wash stage and minimise the EW bleed stream. The main driver for this is the cost of the cobalt sulphate contained in the electrolyte. Some results from the latest circuit modifications at the Nifty and Girilambone Copper Projects are presented to confirm the benefits of using both coalescing systems and a wash stage. The EW bleed has been reduced to a level that is less than the loss internally in the SX stage to stage entrainment. There has been an occasional need to add chloride to the EW to maintain sufficient concentration to act as a growth modifier.

Jan 1, 2002

By George W. Riter

A distinguished engineer, the active head of a large mining company, has said that surveying attains the dignity of a profession only in the hands of a few men—the few who know how to keep notes that will be understood by even a novice without further word of explanation. Of all mine-records, survey notes are perhaps the most important. The maps made from them serve as a working-guide, and as framework for other data; and when, from any cause, access to underground workings is shut off, the surveyor&apos;s record often becomes invaluable. So seldom docs a surveyor have a chance to check underground surveys by making a closure, that he is compelled to rely on the precision of each step of his work for the accuracy of the final result. When data are fully recorded on the spot, the notes, even in the hands of second parties, become evidence of the care and precision with which the surveying was done. It is worth a great deal to be able to pick up the work of a former surveyor where it was left off, and to be able to carry it forward without rctracing from the beginning. The purpose of this paper is to describe the survey-note system of a mine now under my direction, in which underground surveys had to be relied upon entirely for the proper division of rich ore-bodies between neighbors, thereby placing a premium on accurate surveying and permanent records. In survey-work, it soon turns out that paper is the least item of expense, and that little is gained by trying to economize note-book space. For many purposes it is best to record notes on cards or loose-leaves, which may be left in the office at the end of the day&apos;s work, and need not be carried into the mine again, there to become smeared with grime and grease. With the loose-leaf or card system, all notes relating to the same local-

Jan 1, 1911