Search Documents

By John H. Ratcliffe, Hans T. Lundberg

In airborne gravity surveys effects of acceleration and irregular movements of the aircraft must be balanced out or overcome. The gradient of vertical gravity is recorded, therefore, by using two masses instead of one. As the amplitude variations are infinitesimal and difficult to measure accurately, at of gradient during flight is positive or negative. The positive portions of the pattern can then be indicated and contoured. Even with these simplifications, the source of energy must be exceptionally stable. General Principles: In the conventional gravimeter the weight of a standard mass is determined at a number of selected points within the survey area. In most systems weight is determined by comparing the gravity pull with extension or torque produced in a wire spring. The instruments employed are sensitive to the slightest movement; they cannot be used on a moving platform unless velocity is kept strictly uniform.

Jan 8, 1959

By Phil Hulse

The Atlanta mine is located in east-central Nevada, approximately 360 km (225 miles) from Las Vegas. It lies in Lincoln County, 116 km (72 miles) south of Ely and 80 km (50 miles) northeast of Pioche. The property is currently operated by the Standard Slag Co. under a joint venture agreement with Bobcat Properties Inc, of Fort Lauderdale, Fla. Operations began in May 1975, and the mill is currently processing 109 000 to 122 500 t/y (120,000 to 135,000 stpy) of gold- and silver-bearing ore. Open-pit mining takes place in a breccia zone that occurs between Ordovician limestones and dolomites on the footwall and Tertiary rhyolites on the hanging wall. The quartz breccia ore is among the most abrasive in the world-shovel teeth must be replaced every week, 19-mm-thick (3/4-in.) steel chutes last about a month.

Jan 9, 1978

By Dadan Munawar, Benny Gunawan

Blasting at Sebesi in Central Tutupan Pit area in South Kalimantan, Indonesia is planned to be using emulsion, where used oil makes up 50% of the total emulsion fuel. The significant amount of used oil from various mining operation units had been of deep concern since it might be reused to implement environmental programs by substituting 50% of fuel with used oil in emulsion, thus decreasing fuel consumption and increasing efficiency by reducing fuel cost. Used oil must pass laboratory test to meet the Indonesian National Standards (SNI) No. 7642:2010 of used oil specification. Other considerations include the location which is adjacent to the mine office facilities with a radius of <1,750 meters (5,741 feet). Thus, appropriate methods must be performed to meet the SNI No. 7571:2010 of vibration threshold in order to implement safe blasting technique and prevent potential damage.

Jan 1, 2015

By Franco Chiesa, David Levasseur, Bernard Duchesne

A 500kg aluminium AlSi7Mg03 casting has been poured and the metallurgical quality at different locations inside the casting has been thoroughly investigated. It included measuring the local tensile properties (YS, UTS, El) in the T6 condition, the dendrite fineness (DAS) and the level of microporosity. A correlation was found between the microporosity level, the local solidification time and solidus front velocity; this correlation allows to predict the porosity level in large aluminium castings (solidification times between 20 and 200 minutes). Quite expectedly, properties varied widely within the casting and the actual mechanical properties were much less than the "textbook values" based on measurements carried out on separately cast standard specimens. A correlation between the secondary dendrite arm spacing (DAS) and the local solidification time was in keeping with previously published data. Finally the conditions to obtain an acceptable finish on machined surface were determined.

Jan 1, 2014

By David B. Plumeau

The Cayuga Mine, a deep rock salt mining, operation, changed from a standard room and pillar mine design to a yielding pillar/pressure arch design five years ago. In general the roof conditions improved. However, entries adjacent to the abutment pillars continued to fail. It was noticed that where abutment pillars were accidentally "notched" (by driving cross- cuts one cut into the pillars), the abutment entries had better roof conditions than where there were no "notches". Experiments with intentionally notched abutment pillars showed that notching did improve abutment entry conditions. During the past four years notch configuration has been varied to suit local ground conditions. Recently, "pre-cutting" of notches has proven itself as a means of protecting abutment entries under severe ground conditions. As an added bonus, the notches improve productivity by providing more places to work and reduce costs because it is not necessary to bolt the notches.

Jan 1, 1981

By V. Sovmen

The gold-ore Olympiada deposit is located within the Yenissei range (Krasnoyarsk Region, Russia). Primary sulphides ores are metasomatic changed rocks, mica-calcite-quartz structure with impurity amphiboles, chlorites, carbon, the rare thin grains of sulfides (up to 3%~5%) and native gold. The structures of ores are fine-grained, prevailing texture of ores - interspersed, vein-interspersed, band-interspersed, veinlet. The most important minerals in the deposit are: gold, arsenopyrite, pyrrhotite, antimonite, Sb-sulphosalt, quartz, muscovite, calcite, siderite, titanium minerals, chlorite and minor sulfides like chalcopyrite, galena, sphalerite, etc. A common problem in mineralogical studies applied to mineral processing (concentration, cyanidation, etc.) is the characterization of gold in ores and technological products. This paper discusses the behavior of minerals during technological process at operating factory in Olympiada Mine and gold distribution in the ores and products. For the mineralogical characterization of minerals ? combination of analytical techniques was used. Gold is encountered in the primary ores as free grains among rocks, growth with sulfides and nonmetallic minerals, inclusions in sulfides, sulphosalt, and nonmetallic minerals. The gold-sulphide ores of Olympiada deposit can be quite complicated for enrichment. With the purpose to increase the extraction of metal from concentrates by liberating the dispersed gold, forming inclusions in sul-fides, there is used technology of biooxidation of flotation concentrates in Olympiada Mine. Gold and the basic ore-forming minerals in the ores feed, sulphidic concentrates, biocakes, tailings of concentrates of flotation and products of hydrometallurgical leaching have been studied in the mineralogical research. During researches it is established that pyrrhotite was completely oxidized while arsenopyrite was oxidized almost completely in the bacterial oxidation process. Pyrite and antimony minerals behave similarly and were oxidized only partially. The main oxyhydroxides in the bacterial oxida-tion process are goethite, limonite and jarosite. The results of mineralogical researches showed reasons of losses of gold during hydrometallurgical enrichment.

Jan 1, 2014

By Marcelo Mourao, Adolfo Pillihuaman, Alberto Nogueira, Cyro Takano

"The self-reduction is an alternative and promising process for production of pig iron because offers decisive benefits such as enhancing the reaction kinetic with decrease in fuel consumption and C02 emissions. The self-reduction mixture of iron ore fines, carbonaceous reducer and additives for slag forming components, without agglomeration, was tested in a laboratory rotary kiln. The additives for slag were defined for presenting two different estimated liquidus temperatures (1623 Kand 1773 K) to verify the effect of these temperatures on the iron-carbon nuggets coalescence process. These mixtures were tested at 1673 and 1773 Kin an experimental rotary kiln. After reduction-melting and coalescence processes the samples were disaggregated and the iron nuggets were classified by size. It was considered that nuggets larger than 7,93mm would be a good reference for coalescence index. Low liquidus temperature slag presented 37% of this larger fraction against only 13.5% for high liquidus temperature one. The low liquidus temperature slag would facilitate contact between the particles of iron-carbon in a rotary kiln, enhancing the coalescence.IntroductionThe slag composition usually depends on the reducer ash composition, the ore gangue, the binder composition and any fluxing material [l], and the mechanism of carbon transportation in slag that contains iron oxide reducible by carbon can be explained by the oxide reduction and the metal carburization. During carbon transportation, the carburized particle is transported to slag-metal interphases by the gravity effect, being assimilated by the metallic phase [2]. When the slag's iron oxide comes in contact with the solid carbon, it is immediately reduced, forming Fe particles and CO bubbles as it is shown in the figure l(a). The Fe particles are carburized by carbon particles; they are liquefied simultaneously in the carbon-slag interphase. The Fe-C liquid particles are transported from the slag-carbon interphase to iron-slag interphase as a result of slag flow, based on the surface tension difference (Marangoni effect), figure l(b). The Fe-C liquid particles coalesce on the iron surface and the carbon is immediately diffused in the iron as it is shown in figure l(c). The reduced iron is carburized continuously by repeated sequences [3]."

Jan 1, 2013

By K. Zhang

Real option value (ROV) method is considered to be more practical and advanced compared to net present value (NPV) method in evaluating a mining project, in particularly when there is substantial uncertainty in the commodity market as well as possible operational flexibility embedded in the project. Usually, it may take months or even years for the commodity product to be available in the market after the mining activation decision is made. The impacts of postponing the delivery of commodity product on the mine?s ROV and NPV are assessed based on the proposed real option method. Postponing the delivery of the products leads to declined NPV and ROV compared to the non-postponing scenario and extended postpone results in higher lost values in NPV and ROV. For a mine with lower mining cost, by postponing the delivery, the exercising threshold of commodity price is lower because the mine owner anticipates that commodity price may rise during the time of postponing. A mine with higher mining cost requires a higher exercising price threshold to ?lock up? the profit when there is ambiguity of market situation due to the postponing of the delivery.

Feb 23, 2014

By C. E. BOCKUSD

WHEN Mr. Bain asked me to lunch with you he requested that I say a few words as to how the Institute could be helpful to the bituminous coal industry. I feel like saying, "Thank you, what have you?" I do not want to trace in detail the story that is old already to many of you. On the other hand it does take some little stage-setting to illustrate what is the matter in the bituminous coal industry, a trouble that must some day be cured. There has been something over a century of bituminous coal production as a real business in this country. True, Joliet and Marquette discovered coal in Illinois in 1673, according to published accounts of their travels, and shortly thereafter Father Hennepin also found Illinois coal in 1689. Coal was mined near Richmond in 1750, and Richmond shipped coal to New York and Philadelphia in 1789. But it was not until 1838 that the production of bituminous coal in this country totaled a yearly output equal to the minimum for one class A mine today, for that was the first year that production exceeded 200,000 tons.

Jan 1, 1930

By Sanna Mustonen, Seppo Mellanen, Mellanen, Pekka Kantia

In Finland Posiva Oy (Company) is responsible for implementing the final disposal programme for spent nuclear fuel of its owners. Company is preparing for the geological disposal in Olkiluoto crystalline bedrock. Excavation will be executed using drill and blast method. Method unavoidably causes variable excavation damaged zone (EDZ) on tunnel surfaces. The EDZ constitutes a risk for long term safety and therefore good control methodology of the blasting technique is required. The thicker the EDZ, the greater is the likelihood for detrimental transport pathways for ground water to transport radio nuclides, should those be present.

Jan 1, 2016

The Ural Mountains, which were formerly the dividing line between Asia and Siberia, area chain of low mountains, the highest peaks reaching only a little over 5000 ft. The country has been much eroded and the mountains now appear as rounded hills. In the central and northern parts turf swamps abound. The range is covered with forests except at the extreme southern end. The trees are mostly pine. Birch grows on cut-over areas, but never to large size. The rivers are small or the fall is slight, so no large water powers are available. A series of rivers with a north and south course, and which are navigable for long distances, furnish cheap transportation during the summer months. Railroad communications are very insufficient. The first active exploitation of the mineral wealth was initiated by Peter the Great, who sought iron and copper for use in his wars against the Swedes. He selected a blacksmith named Demidoff to supervise operations and gave him rights to most of the Ural and to the Altai. The Nijni Tagil Estates are still in the possession of the Demidoff family. The original large grant was subsequently subdivided through inheritance and marriage, but the Ural is still a country of very large estates, some of them held as leases only and some of them by actual ownership.

Jan 6, 1919

By Cam Thomas

The initial application for reflectorless laser technology was for profiling rock faces to determine front row burden and improve flyrock control and airblast. Over the past fifteen years a number of laser systems have been developed for general ground modeling purposes and GPS offsets, but these advances have yet to gain common acceptance in construction, mining and quarry blasting. This paper will outline a number of applications for reflectorless laser technology, including the latest method for rock face profiling, mapping, and 3-D modeling to calculate available and excavated rock volumes. Drilling deviation measurements will be presented in conjunction with rock face profiling to demonstrate how this information can be used to improve blast results. In complicated excavations, the actual quantity of rock excavated for payment purposes and the amount of overbreak can be very controversial. Procedures to calculate these volumes using laser technology will be outlined and comparisons will be made between these results and traditional techniques.

Jan 1, 2003

Meeting of April 24, 1914.-President Thayer announced the appointment of the Committee on Safety and Sanitation. The Committee on Nominations for officers for 1915 was appointed, as follows: William J. Cox, Chairman; H. Poster Bain, Joseph Daniels, Charles E. Mills, R. V. Norris, E. Gybbon Spilsbury, and Herbert A. Wheeler. The request of twenty residents of Salt Lake City and vicinity for permission to establish the Utah-Nevada Local Section was granted and R. C. Gemmell was appointed Chairman of the Committee on Organization. The following resolution was adopted: Resolved: That under authority of Article V, Section 7, of the Constitution, a special Committee be and hereby is appointed, to consist of the President and six other members of the Institute, to be named by him, Who shall be authorized to appear before the proper authorities at Washington and urge that Mining Engineers be appointed upon the proposed Commission for revision of the Federal Mining Laws. Further Resolved: That the activities of this special Committee be restricted to the authority given in this resolution.

Jan 6, 1914

By Liu Z. C

Evans&apos; theory for chisel shaped picks is well known in the field of rock cutting technology. It has been widely accepted as a good mathematical description of how coal and other rocks break under the action of a simple wedge or chisel. Subsequently, Evans proposed a corresponding theory for pointed shaped picks. Theory along with experimental evidence from the laboratory has consistently shown that chisel picks are more efficient than pointed picks. However despite such evidence, pointed picks continue to be the preferred shape in most practical cutting applications. Evans&apos; theory for pointed picks was developed in an attempt to shed light on this apparent incongruity. The theory although predicting forces of the right order was found to be deficient in several respects. This paper examines Evans&apos; theory for pointed picks and proposes changes to it, which brings the theory much more into line with measured data. The issue of the relative efficiencies of chisel and pointed shaped picks is also examined on a theoretical basis and the apparent incongruity is Resolved.

Jan 1, 1995

By Walter O. Snelling

IN combating mine-fires the use of carbon dioxide as a means of producing an atmosphere in which combustion cannot be sustained, has been many times suggested and frequently tried, generally with a fair degree of success. The carbon dioxide is produced by acting on limestone with dilute sulphuric acid, large wooden boxes being used to hold the limestone, and arranged in such a manner that one box may, be cleaned and refilled with blocks of limestone while another is being used in generating the carbon dioxide. The gas is led by means of pipes of large diameter to the location of the fire, tight brattices having been previously put up as close to the fire as possible on every side, so as to limit the space to be filled with the .gas to the smallest possible volume. The cost of producing Carbon Dioxide has been, however, a decided draw-back to the use of this method, and the danger of producing carbon monoxide by the reduction of the carbon dioxide by heated carbon, and consequently bringing about an explosion, has also tended to prevent the application of this method. The use of sulphur dioxide in combating mine-fires has not, I believe, been previously suggested or tried, and yet the method presents such decided advantages over the use of carbon dioxide that it seems proper to suggest the advisability of considering it as a cheap, convenient, and safe means of fighting stubborn mine-fires. 1. Cost, Preparation, etc.-One ton of brimstone, costing from $20 to $30, will produce about 25,000 cu. ft. of sulphur dioxide gas, and allowing for all sources of loss it is probable that sulphur dioxide gas can be produced for about $1,300 per 1,000,000 cu. ft. For carbon dioxide gas, produced by the action of sulphuric acid on limestone, a good estimate would be $4,000 per 1,000,000 cu. ft., provided that sulphuric acid

Sep 1, 1908

By Robert R. French

Beneficiation of low-grade nonmetalliferous mineral deposits by electronic color sorting is currently undergoing a period of rapid development. For those deposits in which the specific gravity, strength, soundness, and electric and magnetic properties of the ore and gangue are similar, the possibility of separation by color, reflectivity, or fluorescence offers hope for the utilization of much poorer quality ore than previously thought possible. For those ores in which consistency of color is required or for which a dry process is preferred, the electronic color sorter is particularly adaptable. Tests performed late in 1966 and reported herein are the result of continued interest in the dry beneficiation of gypsum and the development of higher capacity color-sorting machines. These tests should be considered only as an indication of the efficiency of the process and only with respect to the low-grade, untreated ore tested. Although most of the ore mined in Martin County, Ind., is of acceptable quality, a few thin carbonate strata and irregular nodules of dolomite and limestone are present within the main evaporite bed (Fig. 1).

Jan 1, 1969

By Walter D. Holland

This is one of a series of instruction guides developed to help instructors present health and safety training courses to workers in the metal and nonmetal mining industry. This course is intended for training those, usually the safety officers, who perform surveys for inhalation contaminants in above ground work areas. The handbook entitled ?Handbook for Surveys of Inhalation Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas? is used as a manual for the course and as a prime reference when performing the actual surveys or interpreting the sampling results. There are six experiments for the students to perform during the course to familiarize them with the sampling devices routinely used during the surveys.

Jan 1, 2011

By Ronald M. Fedrick

The microtunneling project for the State of Hawaii&apos;s Natural Energy Laboratory (NELH) facility in Kona, Hawaii, was awarded to Nova Group Inc., Napa, California. Nova has developed both microtunnel and deep pile cofferdam experience. Both of which would be required for this project. The project was designed by Makai Ocean Engineering of Honolulu as a continuation of the Ocean Thermal Energy Project (OTEC). The world&apos;s first OTEC plant has been successfully operational at NELH since 1982 netting approx 50 kw of usable electric power from a gross generation of 210 kw. A second plant designed to draw 39°F cold water from 3,000 ft below sea level and produce a gross output of 1 mw with a net 500 kw of usable power required 2 - 54 in. finished diameter pipelines. An ongoing problem with earlier offshore pipelines has been the damage to the near-shore pipes within the surf zone. The necessity for a deeper connection between the land based pipe and submerged sea pipeline was obvious. Earlier pipelines had been drilled and shot through the shoreline. This process was only practical at shallow depths. Makai Ocean Engineering and the NELH scientists looked at different methods to get the pipeline through the shoreline at a depth of 80 ft below sea level. Initially, the direction drilling method was proposed as the most potentially practical method. A contract was awarded and various attempts were made to complete a successful

Jan 1, 1995

By Peter J. Clarke

Development of the mineral and energy resources of Afghanistan appeared to be a top priority of the Soviet-controlled Government in the country. In the Afghan Government&apos;s plan for 1980-81, the largest allocation in the development budget was for mines, industry, and energy (46.7%). In contrast, only 23.1% of the budget was allocated for agricultural development, despite the fact that the great majority of the population was dependent on farming. The mineral industry of Afghanistan consisted of the production of natural gas, cement, coal, fertilizer materials, and rock salt. Production levels for all of these commodities were down an average of 45% from those of 1978, before the Soviet invasion. Prior to the invasion, small quantities of asbestos, barite, and talc had been produced along with about 6,000 to 7,000 kilograms per year of lapis lazuli, a semiprecious gem stone. Afghanistan had supplied about 80% of the world&apos;s output of lapis lazuli. Following direct Soviet intervention, production of these minerals declined to near zero.

Jan 1, 1983

By Ze-Qiang Xie, Bai-hui Wang, Feng Chen, Ling-zhi Yang, Yu-feng Guo

In this paper, based on the big data in steelmaking process, equation about the relationship between steel composition (especially the oxygen content) and the element yield is established by using mathematical analysis method to analyze the factors influencing yield. Meanwhile, combining the alloy yield data-base that were established based on self-learning of historical data and computer technology in steelmaking process, a method of yield prediction of alloy elements is studied. To provide support for this method, alloying elements yield prediction software is developed to realize the rapid and intuitive site operation guidance, and to realize the precise control of dosage of alloy material.

Mar 1, 2017