Search Documents

By Grieve BL

For a blast to be successful both heave and fragmentation must be satisfactory. Amongst the major factors influencing blasting are rock properties. This paper considers the effect of rock density on fragmentation and heave and how better results can be achieved in dense ore. Patterns which increase the heave and give better fragmentation are examined and the application of theory to the blasting of the Dales Gorge Haematite, density 4.2 - 4.5 t.m.,3 is then discussed. The drilling of staggered patterns instead of square patterns and a shallower 'V' initiation system has given better heave and fragmentation. This practice has re- duced backbreak and improved toe conditions; these factors have resulted in increased load ing rates. There has been an increase in the lump/fine ratio which is consistent with the theory although other factors such as ground conditions could have contributed.

Jan 1, 1978

Grade control is an important factor in the on-going success of a mining operation. Grade control criteria will vary depending on the commodity being mined. Financial considerations determine the actual grade control criteria at any one mine site. Mining and metallurgical capital and operating costs are ultimately used in ascertaining cut-off grades employed in grade control. The metallurgical characteristics of the ore, and ultimately the equipment selection and design of the plant, are based on samples provided by the exploration geologist. Ore variability is an important factor in designing the process plant. Ore variations, outside of those catered for in the design, as well as large ore changes on a daily basis, will impact on the metallurgical performance, and hence the economics of a mining operation. Therefore good liaison between the grade control geologist and metallurgist will undoubtedly lead to a more consistent, and more profitable mining operation.

Jan 1, 1993

In the first half of 1987 two four metre diameter raise bore holes were drilled at the Olympic Dam Project for ventilation purposes. The first hole, 476 m x 4.0 m diameter was completed in 96 days, 35 days longer than scheduled. The second hole, 407 m x 4.0 m diameter was completed in 39 days, 2 days ahead of schedule. Both holes were drilled with a Robbins 121R rig using a Wirth head that consisted of 23 face cutters and 5 side cutters, supplied by a contractor. After the sites were located a grouting program was carried out to help seal off an aquifer between 160 and 180 m below the surface. Cavities discovered in the Andamooka Limestone were filled with concrete. Because of the overlying dune sands and clay both sites were pre-sunk to the competent Andamooka Limestone.

Jan 1, 1988

By Jones JJ

A laboratory study of size segregation is described using a model of a Paul Wurth hopper industrailly employed for blast furnace charg- ing purposes. Experimental charge materials used in the study were glass ballotin.i (1-4mm dia.) and sinter fines (0.25-4mm). The tracer material employed consisted of coloured glass beads. The results of the study show that the discharge stream from a Paul Wurth hopper is characterised by an initial negative segregation followed by a positive segregation and that this segregation pattern is a property of the hopper geometry and the filling conditions. A simple computer model based on experimental tracer concentration results is proposed. The measured segregation results and those predicted by the model show close agreement. Application of the results with special reference to the effect of size segregation on charge permeability in blast furnaces is also included.

Jan 1, 1984

By Bill Almdal

Today?s presentation ? Role of the Regional Issues Working Group ? What does RIWG do? ? How can RIWG?s work benefit Stakeholders? ? Review of forecasts vs. reality ? How have past investment compared to the reality? ? Risks to future growth ? The growth potential is very high and so are the risks ? Examples of outputs ? Housing needs ? Growth in population ? Tires for large trucks The Regional Issues Working Group ? Our vision ? To provide a proactive process which promotes the responsible, sustainable development of resources within the Regional Municipality of Wood Buffalo for the benefit of all stakeholders ? What we do ? Facilitate planning for growth ? Facilitate effective and efficient resolution of issues ? Involve all of the resource developers and affected stakeholders in planning ? Develop plans for sharing benefits with Aboriginal stakeholders ? Benefits for Stakeholders ? Our forecasts include up-to-date information from all developers ? including information on employment and housing needs ? Our forecasts are the basis of planning for many stakeholders ? and can assist in their development planning

May 1, 2002

By A. F. Alsobrook

Specialty silica materials, as defined in this chapter, are rocks that consist predominantly of silica (SiO2) and are produced as chunks, round pebbles, and sawed or trimmed blocks and other shapes for nonconstruction applications. The rock types include quartzite, sandstone, novaculite, flint, chert, and vein quartz. Other terms used commercially include jasper, silex, lascas, and rock crystal. In its publication, Minerals Yearbook, the US Bureau of Mines (USBM) reports the production and consumption of some specialty silica materials under several headings. Quartzite, sandstone, and novaculite used in abrasive applications are addressed by the USBM under Abrasive Materials. Lascas, a type of vein quartz used in growing synthetic quartz crystals and in fusing applications, is discussed under Quartz Crystal. Silica gravel used in manufacturing silicon metal and ferrosilicon, as metallurgical fluxstone, and as a filtration medium is covered under Industrial Sand and Gravel. Information on

Jan 1, 1994

By W. B. Hall, Joy D. Lewis

Mine-run ore is received at Vitro in gondola cars and fed directly to a Cedar Rapids impact crusher. Following screening, the undersize travels through a recently installed three-stage sampling plant where successive cuts are executed by conventional Geary-Jennings type cutters to produce a final sample of 1 lb per ton of raw ore fed. Crushed ore is transported to one of three storage silos or to stockpile, depending upon grade and type of amen- ability. This permits the blending of a mill feed with some degree of consistency. Final grinding is accomplished in one of two closed circuit ball mill-classifier systems allowing simultaneous processing of two basic types of ores. High acid consumers may be leached separately in the required environment. Part of the free acid remaining can then be utilized by an ore stream entering later whose component ores require much less free acid for leaching.

Jan 11, 1958

By E. P. Carman

In this report, the Federal Bureau of Mines presents a summary of the occurrence, properties, and uses of some natural bitumens, using the layman's or dictionary definition of bitumens - that is, naturally occurring hydro-carbons. Emphasis is on the less common solid and semisolid bitumens, particularly those occurring or used to some extent in the United States. This comprises data from many sources and references to these sources for more detail than is given in this summary. This paper was prepared primarily to answer questions about some of the less known bituminous materials. The word hydrocarbons could just as well have been substituted in the title for bitumens, but bitumens was used, since an abstract of the paper was presented at a meeting where the major emphasis was on bituminous materials. The reader will realize that coals, of which only the more unusual such as the cannel coals and torbanites are discussed in this paper, are primarily mixtures of bituminous materials and carbon. The amount of bituminous material, or volatile matter, in coals is greatest in the lower rank coals and the unusual types described in this paper, and decreases as coal rank increases. However, since no method other than destruction of the original coal substance by heat is known that will separate the volatile matter from the carbon, it appears reasonable to classify the coals with other bituminous materials, particularly since bituminous coal - the most widely used coal - by its name indicates the combination of bituminous materials and carbon.

Jan 1, 1961

By Brian W. Mackenzie

In this age of advancing technology, mining companies are confronted with increasing competitive forces. The depletion of high-grade deposits and the development of substitute materials are intensifying market competition. The accelerating activity of petroleum companies in mineral exploration is increasing competition for deposits. At the same time, the trend in government policy is towards a reduction in traditional mineral-industry incentives. To succeed, the mining company must respond to these changing economic conditions by developing a decision-making framework that can effectively contend with the new opportunities and constraints. What are the elements of such a decision-making framework?

Jan 1, 1970

By Isaac A. Zlochower, Michael J. Sapko, Ronald S. Conti

This paper describes a U.S. Bureau of Mines investigation of large-scale coal dust explosions in an experimental mine using a high speed electro pneumatic mechanism for the rapid grab-sampling of gases and dusts. This technique enables the monitoring of pyrolysis and charring in fuel dust particles, and the collection of gaseous combustion products, in both large and small-scale explosions. Data obtained from full-scale dust explosion tests at the Bureau of Mines Lake Lynn Test facility show the following: Rapid sampling appears to "freeze" the burned gas compositions at the flame temperature values. Gas samples taken entirely in the flame zone consist of pyrolysis and combustion products with very low residual oxygen. The particles collected in the flame zone show signs of extensive pyrolysis and charring. Measurements of gas concentrations and particle flame temperatures suggest that char burning may have occurred in the flame zone.

By Wesley Schmutzler

The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.

By Ralph Musick, Brian Briggs

The U1h Shaft Project is a design/build subcontract to construct one 6.1 meter(m) (20 feet [ft.]) finished diameter shaft to a depth of 321.6 meters (m) (1055 ft.) at the Nevada Test Site (NTS). Atkinson Construction was subcontracted by Bechtel Nevada(BN) to construct the U1h Shaft for the Department of Energy (DOE). The project consists of furnishing and installing the sinking plant, construction of the 321.6 m(1055 ft.) of concrete lined shaft, development of a shaft station at a depth of 297.5 m(976 ft.), and construction of a loading pocket at the station. The outfitting of the shaft and installation of a new hoist may be incorporated into the project at a later date. This paper will describe the design phase, the excavation and lining operation, shaft station construction and the contractual challenges encountered on this project.

Jan 1, 2001

By H. R. Butler

"The Ontario Division of Inca Metals Company, a Unit of Inca Limited, operates eleven mines, four mills, three refineries, one smelter and one iron ore recovery plant. All but one mine, mill and refinery are located within a fifty kilometer radius of Sudbury, Ontario. A mine-mill complex is located some 100 kilometers west of Thunder Bay on the shore of Lake Shebandowan and a nickel refinery at Port Colborne.During the past 10 years the use of recycled water in our milling operations has increased to more than 95% at each mill. This high degree of water reuse has reduced the (a) need for fresh water and (b) the contaminant level of the downstream aquatic environment. The aggregating of effluents in a common receptor provides a process water having a consistent quality thereby minimizing upsets in mill metallurgy while concurrently improving the operating economies and the downstream aquatic environment."

Jan 1, 1980

By N. A. C. Smith

During the past, six, years, the Bureau of Mines has made and. published several hundred analyses of typical crude oils and 'has developed a system of interpreting the analyses and of classifying crudes. This system is presented here with. It is apparently equate for classifying crude oils into four main groups and has also been found very convenient in studying the geological relationships between crude oils, and the probable refinery yields of valuable products from them. Crude petroleum is morn to be a very complex substance. An analytical statement of its properties must, therefore, consist of two distinct parts, - first, the report of the results of the determinations made by the analyst in the laboratory, - second, the proper arrangement, classification and interpretation of these results so that the analysis, as a mole, will indicate the meaning- and the relative- importance of the essential characteristics of the oil.

Jan 1, 1927

By S. W. Zoldok

"ERRATUMFor paragraph 1, page 1, read the following:The Cle Elum nickeliferous iron deposits occur on an unconformable contact between the serpentine and overlying Swauk sandstone formation and extend about 2 miles along the Cle Elum River in Kittitas County, Wash.The linear extent of the deposits and their proximity to a large source of,electric power and coal supply indicated that a development program was in order to determine the probable grade, extent of the ore bodies, and a suitable metallurgical process for recovering the iron, nickel, and chromium from the ore.The northern portion of the serpentine formation was investigated by the Bureau of Mines from August to December 1943 and from August to October 1944. The investigation consisted of road building, diamond drilling, sampling, and metallurgical tests.The Geological Survey assisted with logging of cores and made geologic and topographic maps."

Feb 1, 1948

By Clyde Longyear

DURING the last two years, the diamond core drill has come rapidly to the front as a very valuable auxiliary to the equipment of the exploration and production departments of oil companies. The diamond drill and the rotary oil drill work on the same general principles, the essential difference being that the diamond drill employs an annular steel bit set with black diamonds ("carbons"), instead of the fish-tail or other type of bit employed by the rotary drill. On account of the brittleness of the carbon and the danger of breakage if subjected to sudden blows or stresses, it is not practicable to attach a diamond bit and core-barrel to the end of a rotary drill stem. The operating mechanism of the diamond drill must be subject to much more sensitive control than the rotary drill. The bit must be rotated smoothly, without the jerks that are incident to the operation of the clutches and chain drives on the rotary draw works, and the feed must be con-trolled in a much more delicate manner than the mere action of a brake on a hoist. To accomplish this smooth rotation, diamond drills are usually built as a self-con-tained unit with the crank shaft of the engine geared direct to the drive shaft that turns the drill rods or stem. One or two hydraulic cylinders connected with a high-pressure pump control the feed so definitely that the bit can be raised or lowered at will, while the bit is rotating, by the simple operation of valves. The smaller-sized-drills for very shallow work usually have a screw feed control instead of the hydraulic feed. The principal uses of the diamond drill in oil work are three: 1. Reconnaissance or structure drilling; that is, the drilling of a number of shallow holes to ascertain the subsurface contour. 2. Scout drilling, or the drilling of holes of smaller diameter than is required for production, to obtain information as to the character of the oil sand and the quality of the oil. 3. Drilling producing wells.

Jan 5, 1923

By H. H. Lowry

SCIENCE attracts the attention and interest of an individual or an industry in general only in proportion to the apparent direct application to its immediate welfare or benefit. Engineering accomplishments, as applied science, therefore receive more recognition than the scientific discoveries on which they are based. Even self-evident truth needs endless repetition before recognition: engineering as applied science cannot advance beyond the science on which it is founded. Scientific research, and discovery, is sometimes forced by the limitations recognized by those active in its development for the use of society and industry and sometimes results from an apparently superficially illogical curiosity about natural phenomena. Research has received inadequate support except in industries born in the laboratory, the chemical and electrical industries, from which many lessons might well be drawn by their elder associates. The rapid growth of these industries has been largely due to close cooperation of scientists and engineers. Most rapid advance is made when the research worker and the engineer keep in close touch with each other's ideas and problems. Many of the developments of modern industry are based on dis-coveries buried for years in scientific journals because the "time was not ripe" at their discovery. The situation with regard to utilization of coal is quite the opposite. The fundamental facts in regard to the scientific aspects of the problem of developing the energy from coal are scarcely known. The engineer, without much scientific cooperation, has accom-plished much in increasing the number of kilowatt-hours per pound of coal from 0.31 in 1919 to 0.69 in 1934, in increasing the 1000 gross ton-miles of freight hauled from 6.1 to 8.3 per ton of coal in the same period, in fuel economy in production of coke, and in developing the production of motor fuel in Germany and England by hydrogenation of coal. This lack of scientific research on the utilization of our most important natural resource, coal, has been due undoubtedly in large part to the reluctance of investigators to study the interrelationships involved in, the complicated processes in which coal is used. These complexities are made

Jan 1, 1936

By R H. Sillitoe

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Geological concepts are employed routinely in porphyry copper exploration at the area selection, prospect appraisal and deposit definition stages. Regional, district-scale, deposit-scale and laboratory-based concepts can all play a role, with the resulting porphyry copper models providing templates for the integration of geochemical and geophysical responses and interpretations. Of the 19 concepts and parameters selected for brief discussion, those relating to subdivision of porphyry intrusions, understanding of diverse and commonly complex alteration-mineralisation patterns and lithocap characterisation are undoubtedly the most influential in exploration. Several of them are of particular importance because of their role in promoting grade development. Additional belt-, district- and deposit-scale features are currently little used but hold promise, whereas others have less practical value but help in underpinning the evolving porphyry copper genetic model.CITATION:Sillitoe, R H, 2015. Recent advances in porphyry copper geology and their exploration utility , in Proceedings PACRIM 2015 Congress, pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Jinjing Dua, Jun Zhua, Kuiren Liub, Bin Wang, Xiaolei Wua

V-Ti-Fe as hydrogen storage alloy was prepared by reducing metal oxides with a metallothermic reduction method. The deoxidation process of the V-Ti-Fe alloy was performed by electro-deoxidation and vacuum induction melting method, respectively. The results showed that the content of oxygen impurity can be controlled at about 0.2wt% after electrolyzing for 240min. Both the maximum values of hydrogen absorption capacity and the effective hydrogen desorption capacity are 2.65wt% and 1.01wt%, respectively. The deoxidization effect of vacuum induction melting process is more remarkable, with Ce as the reducing agent. It is found that Ce addition is beneficial for reducing the componential segregation, promoting the hydrogen absorption activation of V-Ti-Fe alloy. When m(Ce)/m(alloy) is up to 5%, the oxygen content has been reduced to 0.05wt% and the maximum hydrogen absorption capacity and the effective hydrogen desorption capacity are up to 3.36wt% and 1.85wt%, respectively.

Jan 1, 2015

By J. Sandford, S. Hennings

EXECUTIVE SUMMARY An approach borrowed from the petroleum industry was applied to the gas development evaluation for the Bulga underground coal mine in New South Wales, Australia. The results enabled the coal mine operator, Xstrata Coal, to systematically plan the extraction of gas in harmony with mine production planning of multiple coal seams. This has allowed for a more proactive approach in preparing the resources and infrastructure needed to capture the gas and accelerate coal mining while maintaining their high level of commitment to safety. Norwest has for decades used gas recovery simulation models to assist the petroleum industry and the coal bed methane (CBM) industry in understanding and forecasting fluid saturations and flow behavior. Norwest developed a similar process with Xstrata to migrate existing mine data at Bulga into reservoir simulation models to study various drainage alternatives. An interesting feature to the evaluation was also developing an understanding of test procedures and nomenclature from the mining industry to properly translate the data for input in simulators developed for the petroleum and CBM industries. The model was then calibrated to actual field data collected from drainage pilot tests that Norwest helped design and monitor at Bulga. The resulting calibrated predictions were then used to develop budgets, schedules, resource requirements, and alternatives for capturing the gas and delivering it to market ahead of mining. Increasing revenue, reducing emissions, improving schedules and cutting costs for the mining operations have all contributed to justifying this advanced approach at Bulga. It has also allowed Xstrata to expand their focus to the sizable gas reserves in seams not currently planned for mining. Several of these seams would be economic gas development targets once the gas recovery infrastructure is installed for the mine. The evaluation process was refined throughout this project and the resulting approach will benefit Xstrata with their broader strategic development of resources in the Hunter Valley and beyond to their worldwide operations.

Jan 1, 2007