Search Documents

By I. Stanculescu

The consolidation of thick and very compressible soil deposits by stone columns associated with cast-in-place plain concrete columns, has been performed for shallow foundations of some heavy industrial structures. The reduction of settlements and increase of soil bearing capacity were thus ensured as a result of soft soil interaction with stone and concrete columns. The results of model tests and in situ large scale applications are presented. A calculation procedure is also suggested for foundation bases improved by the proposed method.

Jan 1, 2010

By Lynn Alcorn, Jeffrey Shawn Peterson

Data collected by the Mine Safety and Health Administration (MSHA) has shown that roof bolting machine (RBM) operators are the second most likely type of underground mining machine operator to be are over exposed to noise, per the MSHA Permissible Exposure Limit. In response to this, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has initiated a project to develop engineering noise controls for roof bolting machines. Key to this research is an evaluation of the duty cycle of a typical roof bolting machine operation and this paper presents the results of such an exercise for data collected at two cooperating coalmines. The evaluation entails a time motion study of an operators' shift, logging each activity for time (e.g., tramming the machine, drilling holes, installing the roof bolt, etc.) and the noise levels associated with each task with a Larson Davis Spark 705+ dosimeter. NIOSH post processed the data to determine which tasks the operator devotes the most time to and the noise dosage accumulated during those tasks. These results provide insight into which portion of the operators' duty cycle is the most prominent contributor to noise exposure and thus, where research activities for the development of engineering noise controls should be focused. It was determined that the task of drilling holes is the most significant source of the operators' noise exposure and project research has focused on engineering noise controls to reduce the noise emissions generated during the drilling portion of the machine duty cycle.

By Deno Pappas, Chrisropher Mark, John Rusnak, Linda McWilliams

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as “The UCS” for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: • Brereton Limestone above the Herrin 6 seam (Illinois) • Turner Mine Shale above the No. 9 Seam (Kentucky) • Sandstone above the Eagle Coal (West Virginia) • Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechical exploration programs.

By G. Ahnell

Throughout portions of four (4) heavily mined Appalachian states subdivided by the Mine Safety and Health Administration (MSHA) as: District 3 -Northern West Virginia and Maryland; District'" -Southern West Virginia; District 5 -Virginia; and District 6 -Eastern Kentucky, active coal mine waste embankments associated with mechanical and/or chemical coal processing facilities of various levels of coal preparation were inventoried. For each site plant specifications, disposal techniques, embankments' characteristics, and coal source data were accumulated. Mapping at 1: 24, 000 and 1: 250,000 scale and Disposal Site Characterization forms were developed to present the findings. Associated abandoned surface and underground openings near each site were also indicated as well as locational data for each site and the areas environmental conditions - temperature, precipitation and vegetation types. A state-of-the-art review of coal preparation, waste disposal, and alternative uses of coal waste is also included.

Jan 1, 1982

By Son Hye Jin

Abstract ? KHNP is participating in the construction of Nuclear Power Plant both in Korea and UAE. ? We want to improve our construction project management process. ? So we are now developing the process model on nuclear power plant construction management. ? For the effective adoption of this process, we are planning to develop IT system. ? For the first step, we were established the Information Strategy Plan

Aug 1, 2013

By T. A. E. Breen

A new high intensity grinding technology has been developed and is now being commercialized by Hicom International of Australia. This has led to the development and manufacture of Hicom 120 grinding mills which are now being sold internationally for a range of mining industry applications. The first commercial process application has been for the diamond sector, where the ability of the mill to remove host kimberlite rock by attritioning, with no damage to the thereby liberated diamonds, is seen to be a most beneficial attribute. There are, however, many other mineral industry applications for this mill. The design of the Hicom mill is unique. Based on a high speed centrifugal motion of the grinding chamber, very high power intensity is delivered to the grinding process. Most significantly, a high acceleration field, 50 times stronger than gravity is produced, creating very high power input per unit of mill volume, and exceptionally fast particle breakage rates, typically 50 - 100 times greater than those in conventional tumbling mills. A mill developing such forces has significant implications to comminution technology and practice.

Jan 1, 1999

By R. L. de Beauchamp

A preliminary investigation was made of the extraction of chromium from ferrochromium by low-temperature chlorination in the 3400 to 5250 C range. The objective was to devise a method for separating chromium from iron in high-carbon ferrochromium produced from domestic chromite concentrates. The majority of iron was removed as a volatile chloride; chromium was contained in the residue as a nonvolatile chloride, which was separated from carbon and unattacked ferrochromium by dissolution. A small rotary chlorination apparatus was designed, built, and used for the chlorination tests, and samples of commercial-grade high-and low-carbon ferrochromiums were chlorinated for comparison of chlorination characteristics. Low-temperature chlorination of three types of ferrochromium resulted in the removal of 81.9 to 91.6 percent of the iron content as sublimed FeC13. Recovery of chromium in a leach solution of the reactor product varied from 82.4 to 93.1 percent.

Jan 1, 1968

In this study, a 3D model of the shovel motion based multi-body system dynamics in the Automatic Dynamic Analysis of Mechanical Systems (ADAMS) environment was developed. The kinematics model of the shovel was modeled as a multi-body system, which comprises the lower, upper, and the attachment mechanisms. The Euler-Lagrangian equations were employed as the computational framework to describe the dynamic behavior of the model. A virtual prototype of the shovel was built in the ADAMS software environment. This environment allows the visualization of a 3D motion of the general mechanical system and the prediction of interference of the moving components of the shovel. The numerical analysis and animation of digging, swinging and dumping motions for the shovel were performed. The superimposed display of the deployment for the shovel in three phases allows a detailed examination of the dynamic interference among assembly components. This research provides a solid foundation for further shovel dynamics performance studies. Keywords: Shovel, Spatial Kinematics, Virtual Prototype, Visualization

Jan 1, 2009

By M. G. Driessen, H. E. Criner

Possible applications of cyclone thickeners for: (1) clarification of the washery water and, (2) recovery of fine coal from the plant bleed. The paper shows: (1) that it is possible to remove all particles including the very finest, from the circulating water, thus obtaining a closed water system and, (2) that reduction of the ash content of the solids of the plant bleed is feasible by means of cyclone thickeners. Performance data for different size cyclones is given in the form of graphs.

Jan 1, 1950

By J. Desrosiers

"Minnova Inc. has five operating divisions thoughout Canada. One of them is Lac Dufault which was established in 1964.Lac Dufault is located 15 km north of Rouyn-Noranda, in what is known as Noranda volcanic centre, in northwestern Quebec. For more than 25 years, Lac Dufault has produced copper, zinc, gold and silver from four different mines: Norbec, Millenbach, Corbet and now Ansil.Ansil, officially in production since July 1989, is one of the deepest mines presently in production in Quebec. This high-grade copper, gold, zinc and silver orebody is being mined at a rate of 1200 tonnes per day with a total workforce of 200 employees.Of particular interest are the high mechanization level of the underground mine, technical innovations also underground, and computer applications throughout the division.IntroductionMinnova Inc. was formerly known as Corporation Falconbridge Copper until 50% of its shares were bought by Kerr Addison Mines Ltd . in 1986 and it became a member of Noranda Group of Companies.Minnova stands for mining innovation. It means Minnovaaims to use state-of-the-art technologies in mining and exploration to achieve maximum efficiency and cost effectiveness. It also means that they aim to use both proven and innovative management principles to the optimum benefit of their employees and shareholders. Minnova has operations across Canada. Presently four mining divisions produce copper, zinc, gold, silver and lead. Two are situated in Quebec: Lac Dufault (established in 1964) and Lac Shortt (established in 1985); one in Ontario; Winston Lake (established in 1988); and one in British Columbia; Samatosum (established in 1989).Minnova has an annual exploration budget of $15 million divided 60/40 between base metals and precious metals. Most of Minnova's exploration efforts are concentrated around their existing mines. Exploration is carried out from six regional offices located at Rouyn-Noranda and Chapais in Quebec; Thunder Bay in Ontario, Vancouver in British Columbia, Reno, Nevada in the United State and Panama City Panama. Each of the Canadian offices maintains close liaison with nearby operations.Lac Dufault Division is located in the Noranda mining camp, approximately 15 km north of the city of Rouyn-Noranda, in northwestern Quebec (Fig . 1)."

Jan 1, 1991

By V. G. Papangelakis, G. A. Moldoveanu

"One of the major commercially viable secondary sources of rare earths elements (REE) are the ion-adsorption ores, containing 0.05-0.3 wt% rare earth oxides physically adsorbed on the surface of clay minerals formed during weathering of lanthanide-rich rocks. Although ion-adsorption deposits are substantially lower grade than other types of rare earth sources, this is offset by the easier mining and processing costs and the low content of radioactive elements. The conventional extraction route involves ion exchange leaching with monovalent cation solutions (usually ammonium sulphate) under ambient conditions; during the process, the lanthanides are desorbed and transferred into solution, being replaced by the exchange cation. While ammonium ions are known to perform best, there is increased environmental motivation to investigate alternative lixiviants in order to minimize ammonium sulphate impact via reducing its use without considerable loss in rare earth recovery.The objective of the present research was to screen various cations salts (alkaline and alkalineearth metals present as sulphates, chlorides and acetates, respectively) in order to comparatively evaluate lanthanide desorption levels and provide a theoretical base of the observed behaviour. The overall aim is to gain a better understanding of how both cation and anion may affect the overall REE recovery from ores in order to provide alternative processing routes. The distinct exchange capabilities of cations were explained in terms of differences in cation hydration enthalpy within the same group, i.e. Cs+ > NH4 + > K+ > Na+ > Li+ and Ba2+ > Ca2+ > Mg2+. For the same cation, it was determined that REE extraction efficiency follows the order sulphate > acetate > chloride, based on dissimilarities in constants of formation values. Various process implications scenarios will be described based on using mixed cations and anion matrices."

Jan 1, 2016

By H. B. Pulsifer

.ABOut 1.5 varieties, or tnodifications, of the best rnagnesiurn available were prepared and subjected to etching tests, then examined for micro-structure. Of the 30-udd etching reagents that were tried, nearly half, mostly ammonium salts, etched the metal satisfactorily. The surfacing and etching of magnesium is shown to be a very simple and quick operation. The density and hardness of magnesium were determined. The most interesting new observations relate to the finding of the hexagonal etch figures, the crystal laminations, and the fact that the metal is plastic, cold, when restrained or quickly deformed. Under slowly applied pressule cold metal deforms slightly, then shears to fracture without plastic flow. The chief structural features of magnesium arc presented in two reduced photographs and 30 photomicrographs. Materials Tested There are only two sources in the United States from which new metal can be procured: the American Magnesium Corpn. and the Dow Chemical Co. No pronounced structural or property differences in the metals from these two companies were disclosed by the work of this investigation. The following materials were obtained from the manufacturers: 1. Massive crystals of distilled metal (American Magnesium Corpn.). 2. Rods of hot-extruded metal, ½-in. squares and 5/8-in. rounds (American Magnesium Corpn.). 3. Sheet magnesium, 0.005-in. thick (American Magnesium Corpn.). 4. Cast stick metal, 13/8-in. dia. (Dow Chemical Co.). 5. Magnesium-aluminum alloy, hot-rolled plate, ½-in. thick (American Magnesium Corpn.). From these materials, were prepared: 6. Sections from a furnace-cooled ingot made from clistilled crystal. 7. Cold-strained pieces from (6), (4) and (2). 8. Pieces cold-squeezed to fracture from (6), (4) and (2). 9. Hammer-struck pieces from (6), (4) and (2). 10. Steam-hammer struck pieces from (6), (4) and (2). 11. Sections from furnace-cooled ingot of the magnesium-aluminum alloy.

By Jack A. Caldwell

"This paper describes the nature of stage curves and the ways in which they have been used to study the construction sequencing of tailings impoundments. They provide a simple graphical method of representing the main aspects of an impoundment, studying the effects of different impoundment geometries, and predicting and controlling impoundment operations.IntroductionThe designer o f a tailings impoundment must, at all stages of design, examine the relations hip between the volume o r tones of tailings that will be deposited at the impoundment, the height to which the tailings will rise in a given time and that rate at which the various parts of an impoundment will be constructed. The operator, if he is to keep proper control of this impoundment, must be able to examine the effect of different deposit ion rates at the impoundment, and the consequences of placing more or less tailings at different parts of the impoundment. The operator must be able to see at a glance just how much higher an impoundment will be at the end o f the following yea r of deposition, and this he must be able to do in order to formulate his annual construction and operating plans.Stage curves are the best way o f modeling an impoundment. The simple impoundment model represented by the stage curves enables the designer and operator visually to examine the relationships between the various factors, such as impoundment volume, deposition rat e and construction rate, that dictate the essential features o f impoundment design and operation.A design model for a tailings impoundment may be formulated as in Figure 1. This involves the site selection process, the definition o f a geotechnical model, a water balance model and a height-capacity-production model."

Jan 1, 1983

By J. Geyer, B. T. Burton, H. W. Newcomen

For open pits developed in tropical climates the upper portions of the pit walls are often located in residual soils and weathered rock. Due to the presence of relict structures, and the relatively low strength of the residual soils and weathered rock, design slope angles in these materials have to be developed by blending the results of kinematic assessments of geologic structures with rock mass stability analyses and traditional soil mechanics. Background information on the engineering considerations of residual soils are discussed, and the results of geotechnical assessments for proposed pit design of the Brisas del Cuyuni Project, located in southeastern Venezuela, are presented.

Jan 1, 2000

By Kazem Oraee

In underground coal mining, particularly room-and-pillar methods, the coal pillars play a significant role in roof stability. If the pillar dimensions are increased, the pillar bearing capacity also increases, but more coal remains in the pillar and therefore the recovery of mining operation decreases. Therefore, determining the optimum pillar dimension based on technical, economical and performance parameters is important. In this paper, the coal pillar is designed by using the concept of ground reaction curve (GRC). For this purpose, the GRC for coal pillars is drawn and then the elastic and plastic zone of coal pillar behavior is determined. Based on elastic and plastic zone, different equations are presented to draw a pillar reaction curve and the process of coal pillar design based on GRC is explained. As a case study, this new technique is applied to study the coal pillar state in Tabas coal mine of Iran. The results show that the presented new approach is successfully used in the design of the optimum coal pillar dimensions, and also determines the elastic and plastic behavior limit, which is important especially for the logical design of yield pillars.

Jan 1, 2009

By Dennis Sánchez Mora, John Jamieson

INTRODUCTION Work by Humphris et al., (2002); Ondréas et al., (2009); Barreyre et al., (2012); and Escartín et al., (2015) has identified active and inactive hydrothermal sites along the Lucky Strike segment. The sites that contain the largest accumulation of known sulfides are located between the north and the southern zones (Figure 1), a vent site area that is referred to as the Main Lucky Strike hydrothermal field (Escartín et al., 2015). Hydrothermal fluid outflow has been linked to a shallow fault network (Barreyre et al., 2012). However, specific constraints on fault geometries have not been determined. Other off-axis sites at Lucky Strike, such as Capelinhos (high temperature vent), and Grunnus (inactive?), as well as a low temperature vent field (on-axis), Ewan, have been described by (Escartín et al., 2015). Given the spatial relationship between the Main Lucky Strike hydrothermal field (MLSHF), and the intersection of northern rift faults with the southern rift faults, a structural analysis of this area can provide insight into the fault controls on fluid flow that leads to hydrothermal venting and sulfide precipitation. METHODOLOGY Structural data (dip direction and dip) was determined using Leapfrog Geo 4.0 software. Bathymetric data was obtained from Escartín et al., (2015) and references therein. The bathymetry was imported into Leapfrog Geo (in UTM format) and, using the structural modelling tool, individual measurements with dip direction and dip data were collected with a focus on the northern volcanic rift and the southern central volcano (Figure 2a). All measurements were taken from what the authors consider as normal faults, and to aid the determination of individual measurements a “face dip” map was constructed, where the bathymetry is colored by slope angle (Figure 2b). All measurements are simultaneously plotted on a stereonet generated by the Leapfrog Geo Software. Data were divided into northern and southern, and western and eastern zones to determine the relationship between hydrothermal venting and the structural geometries at Lucky Strike (Figure 2c). Slip measurements for individual faults were determined along the dip of the fault with a measuring tool. Net slip, heave (horizontal displacement), and throw (vertical displacement) was calculated for each of the zones.

Jan 1, 2018

By E. E. Ungar

Criteria applicable to noise in coal cleaning plants are presented, and the generally applicable noise control principles and approaches are discussed. The operating characteristics and equipment of coal cleaning plants are described. Considerations entering in the selection and design of noise control means are delineated, and specific means for equipment noise reduction are described. The limited utility of acoustically absorptive materials in plant spaces is indicated, administrative means for reducing worker noise exposure are pointed out, and ear-protective devices are described briefly. The reduction of plant noise reaching nearby communities is discussed. Programs leading to quieter machines an coal cleaning plants are suggested.

Jan 1, 1974

By H. P. Stüwe

HE recent papers of Aust and Rutter112 have again brought to mind the importance of certain "special" orientation relationships between the lattices of two fcc crystals on the mobility of the grain boundary separating them. No theoretical treatment of this problem has been offered till now. The only principle published so far that has given an indication why certain orientation relationships should be "special" is the counting of "coincidence sites" according to the suggestions by Kronberg and Wilson.3 The "coincidence plots" published by these authors show, for instance, that two fcc lattices rotated by 38 deg around a common (111)-axis have 1/7 of their lattice sites in common. Such an orientation relationship is also characteristic for high boundary mobility. The accuracy of the orientation relationship needed for high mobility is not too rigid. Deviations up to 10 deg from the ideal orientation seem to be tolerable as can be gathered from the experimental data.'j4 The auestion arises, then. how the density of coincidence sites will be affected by a deviatioi from mathematical accuracy. This can be checked by a simple model. Two sieves are prepared, the arrangement of the holes corresponding to lattice sites on a (111)-plane in a fcc crystal. They are placed upon each other, Fig. 1. One is kept fixed, the other is rotated around an axis pushed through one hole in common to both. The light falling through holes of both sieves is then a measure for the density of coincidence sites. If the diameter of the holes is very small, light intensity is contributed only by holes the centers of which coincide "exactly." If the diameter of the holes is rather large, some intensity will be contributed by

Jan 1, 1962

Process mineralogy is an inter-discipline in the fields of mineralogy and mineral processing. As a predicting and trouble-shooting tool, process mineralogy helps address all mineralogical issues and problems related to mineral processing. It provides useful information on process design and optimisation, flow sheet development and cost reduction. As more and more complex and refractory ores are being discovered and processed, it is believed that process mineralogy will gain more attention and play a more important role in process design and optimisation. This paper will first discuss the scope of process mineralogy and mineralogical factors that may affect mineral processing of various ores, and then focuses on the application of process mineralogy in process design and optimisation through case studies.

Jan 1, 2008

A Robust Chemically Enhanced Electrostatic Separation Technology Physical separation processes such as gravity, magnetic and electrostatic separations are extensively used in heavy minerals separations. Electrostatic (aka High-Tension) separation facilitated by the conductivity differences, in particular, is used for separating rutile from zircon. Although electrostatic separation is effective, it is not efficient. It suffers from separation efficacy issues owing to sensitive variables such as humidity, surface contamination, particle sizes and the temperature of the feed and other equipment parameters. The variations in the process conditions especially with humidity, temperature of the feed and the mineralogy and surface impurities can cause significant reduction in the separation resulting in production rate losses and product quality issues. Cytec Industries has developed chemical enhancement technologies for electrostatic separation for rutile -zircon separation from the heavy minerals. The major advantage of our technology is its higher separation efficacy in the first pass, substantial energy savings and most importantly its ability to do separation at room temperatures. The bolt-on nature to the existing electrostatic also an added feature that reduces the capital expenditure significantly. The separation efficiency between rutile and zircon was increased as much as 8 - 11 per cent compared to control. It is possible to extend the chemical enhancer technology to problematic feeds and other mineral systems that are not easily amenable to conventional electrostatic separation.

Sep 13, 2010