Search Documents

By Matt Leeming

Several of the underground mines in the UK require a significant number of cable bolts to be installed, remedially, to control worsening roadway conditions. Often the access is limited and the only power source is compressed air. Machines for this duty are generally designed to perform with 100 psi but regularly only half of this is available. This paper seeks to outline the difficulties this situation causes the Rock Bolting Engineer, highlight the technical requirements for a machine of this type to succeed and detail a solution offered by our engineers.

Jan 1, 2007

By Martti Hagfors

Underwater explosions have been used as a test method for the determination of energy content of explosives for several decades. This is the only test method by which shock, gas heave and total energy values can be measured separately. The experimental data can be measured from the pressure-time curves measured by the pressure-recording unit. The shock energy is integrated from the shock peak area and the gas heave energy is calculated from the time interval between the primary shock wave front and the shock wave caused by the first bubble implosion. tb. Bubble period, tb, is the time of first bubble oscillation, the time which passes after the shock peak front to the first bubble peak. The total energy value is the sum of these two partial energies.

Jan 1, 2009

By Kush Patel, Gary Cavanough

Mining operations consume over 2.5 Billion Australian dollars’ worth of bulk explosives annually (Richardson, 2018). Despite the large volume of product used, current practices only conduct a cup density test of the product being used. Explosive products are made up of a number of components, each with an effect on the performance of the explosive. This paper presents methods currently available for the evaluation of bulk explosives and discusses the results of the evaluation of bulk explosives using each of the methods. Through the preliminary experimental analysis, wet chemistry and the Bulk Explosive Analyser were found as methods most suitable for the evaluation of bulk explosives. This paper also presents data obtained from the experimental comparison of the wet chemistry method and the Bulk Explosive Analyser. Through a total of 60 tests carried out on 10 different bulk explosive products the average error of each method was determined, the BEA presented an average error of 0.11%, whereas, the wet chemistry method presented an average error of 1.90%. This is a significant difference when considering the importance of formulation of explosives. Further investigation into the capabilities of the BEA are also presented in this paper.

By Dennis E. Bell

"This paper describes exploration and development to 1982 in the southern half of the northeastern British Columbia (Peace River or Northeast Block) inner foothills metallurgical coal belt. Gates Formation, Fort St. John Group, is the primary target; Gething Formation, Bullhead Group, is secondary. This part of the belt remains wilderness when compared to its other parts. Practical formational and structural mapping is described. A local problem known as the Secus Mountain or Mount Belcourt conglomerates is discussed. The three major explorers have been Denison Mines, PetroCanada, and Crows Nest Resources, all with partners. Initial mine construction and rail spur construction are continuing. The new town of Tumbler Ridge is being built. Introduction This paper describes exploration and development to 1982 in the southern half of the northeast British Columbia metallurgical coal belt. The area (Fig. 1) trends 120 km northwest from the Alberta border to the Wolverine River and Bullmoose Creek. The belt averages 15 km in width, and is 20 km at its widest. Physiographically, the area is dominated by rugged inner foothills, with relief to 1,500 m. The trend of the structures is transected by a dozen rivers flowing southwest to northeast away from the Continental Divide. The Rockies, lying immediately to the west, control the climate. One fact continues to colour all coal work in the area. When compared to the other parts of the western Canadian foothills and Rockies coking belt, it remains the least accessible and least mapped portion. Lack of access also makes all work expensive. Current activity centres about two mines in construction at the northwestern end of the area. Denison Mines and partners are developing their Quintette project, and Teck Corporation and partners are developing their Bullmoose project. PetroCanada and partners have intensively explored their Monkman-Duke Mounta,in project, but mine construction awaits better economic times. The rest of the area remains lightly explored, with the exception of some intensive work on particular structures by Denison and Petro-Canada. The focus of coal work has been metallurgical bituminous coal seams contained primarily in the Gates Formation (Fig. 2) and secondarily in the Gething Formation. These formations are found in generally en-echelon structures ranging to several kilometres in width."

Jan 1, 1985

By L. Franko, S. Klima

Wet-drum magnetic separators are used extensively for upgrading iron ore and for magnetite recovery in dense-medium circuits. In this study the performance of a continuous, laboratory wet-drum magnetic separator was evaluated with and without the application of ultrasonic energy when processing dense medium slurries. Test variables included magnetic-to-nonmagnetic ratio, solids concentration, and nonmagnetic materials. The results indicate that under certain conditions, the purity of the magnetic material increased after ultrasonic treatment.

Jan 1, 2001

By Loren R. Anderson

A probabilistic slope stability computer model was developed at Utah State University and independently evaluated by CH2M Hill Consulting Engineers as a design and analysis tool. Volume I of this report describes the model and Volumes III and IV are users manuals for the computer programs. This volume (Volume II) constitutes the report by the CH2M Hill. It includes a description of a field investigation and stability analysis of an existing tailings dam. Based on the results of the analysis, the tailings dam was evaluated for redesign using probabilistic considerations. Conclusions are made regarding the usefulness of the model as a design tool.

Jan 1, 1982

By M Zoorabadi

Overcoring is a common technique to measure in situ rock stress using the concept of stress relief. The strains measured during overcoring are used to calculate the stress tensor assuming continuous, homogeneous, isotropic and linear elastic behaviour. This approach does not recognise any effect of the thickness of the rock annulus produced during overcoring instead assuming that the stresses are entirely a function of the difference in strain between the start of the overcoring and the end with no regard to the transient strains produced. Three-dimensional numerical modelling was used to simulate the overcoring process and investigate the impact of core diameter on the transient stresses and strains during overcoring. This study showed that in thicker core, maximum transient axial stresses and strains occur when the drill bit approaches the measuring point and greater tensile axial stresses were produced when the annulus was thinner. CITATION:Zoorabadi, M, 2018. Numerical study of annulus thickness on overcoring stress measurements, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 274–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By B. Tiryaki

Performance prediction models for partial face mechanical excavators, when developed in laboratory conditions, depend on relating the results of a set of rock property tests and indices to specific cutting energy (SE) for various rock types. There exist some studies in the literature aiming to correlate the geotechnical properties of intact rocks with the SE, especially for massive and widely jointed rock environments. However, those including direct and/or indirect measures of rock fracture parameters such as rock brittleness and fracture toughness, along with the other rock parameters expressing different aspects of rock behavior under drag tools (picks), are rather limited. With this study, it was aimed to investigate the relationships between the indirect measures of rock brittleness and fracture toughness and the SE depending on the results of a new and two previous linear rock cutting programmes. Relationships between the SE, rock strength parameters, and the rock index tests have also been investigated in this study. Sandstone samples taken from the different fields around Ankara, Turkey were used in the new testing programme. Detailed mineralogical analyses, petrographic studies, and rock mechanics and rock cutting tests were performed on these selected sandstone specimens. The assessment of rock cuttability was based on the SE. Three different brittleness indices (B1, B2, andB4) were calculated for sandstones samples, whereas a toughness index (Ti), being developed by Atkinson et al.1, was employed to represent the indirect rock fracture toughness. The relationships between the SE and the large amounts of new data obtained from the mineralogical analyses, petrographic studies, rock mechanics, and linear rock cutting tests were evaluated by using bivariate correlation and curve fitting techniques, variance analysis, and Student?s t-test. Rock cutting and rock property testing data that came from well-known studies of McFeat-Smith and Fowell2andRoxborough and Philips3have also been employed in statistical analyses together with the new data. Laboratory tests and subsequent analyses revealed that there were close correlations between the SE and B4 whereas no statistically significant correlation has been found between the SE and Ti. Uniaxial compressive and Brazilian tensile strengths and Shore scleroscope hardness of sandstones also exhibited strong relationships with the SE. NCB cone indenter test had the greatest influence on the SE among the other engineering properties of rocks, confirming the previous studies in rock cutting and mechanical excavation. Therefore, it was recommended to employ easy-to-use index tests of NCB cone indenter and Shore scleroscope in the estimation of laboratory SE of sandstones ranging from very low to high strengths in the absence of a rock cutting rig to measure it until the easy-to-use universal measures of the rock brittleness and especially the rock fracture toughness, being an intrinsic rock property, are developed.

Jan 1, 2006

By M Barley, C A. RosiFre, L Lobato

The Carajßs iron ore deposits contain approximately 17.5 billion tons of ore with >64 per cent Fe and occur in the eastern part of the Amazonas Craton. They are hosted by jaspilitic banded iron-formation (BIF) of the Carajßs Formation which, together with metavolcanic rocks, comprise the ~2.75Ga Grpo Parß Group of the Itacai·nas Supergroup in the ~1000 km long, E-W trending Carajßs Synclinorium. The Carajas Formation comprises discontinuous layers and lenses of partly dolomitised BIF (17 - 43 per cent Fe and 35 - 61 per cent SiO2) and lenses of high-grade iron ore, cut by mafic sills and dykes. The high-grade iron ores occur as large tabular bodies of friable (soft) hematite with smaller lenses of hard (compact) hematite. The hard hematite ores typically occur at the contact with the underlying volcanic rocks and are surrounded by an aureole of hydrothermal carbonate alteration. BIF that has been overprinted by dolomite and magnetite crystallisation has recently been discovered at depth in the N4E Mine. With increasing amounts of carbonate, the original lamination (microbanding) and other fine primary structures in the BIF have been progressively obliterated resulting in alternating carbonate and iron oxide mesobands. The friable hematite ore that is characteristic of the Carajßs deposits results from ongoing weathering and leaching of the carbonates from this type of altered BIF. The hard hematite ores probably result from more extensive early oxidation. The association of both carbonate-altered and jaspilitic BIF with the N4 Mine is similar to that observed at the Mount Tom Price deposit in Western Australia, where carbonate-altered BIF occurs below massive hematite ore with a jaspilitic halo developed above the orebody. This indicates that as at Mount Tom Price, hydrothermal carbonate alteration and associated loss of silica from BIF may be an important step in the formation of these giant hematite deposits.

Jan 1, 2002

By D. Izerdem, S. L. Ergun

"Beneficiation of the finely disseminated valuable minerals has been an important issue in the mineral processing field for decades. Treatment of the fine materials becomes difficult with using traditional gravity concentration equipment. To investigate particles behavior in a commonly used conventional gravity concentration equipment, a comprehensive study was undertaken in a plant, which only consists spiral concentrators as concentration units. Spiral concentrators require relatively coarse material to effectively concentrate valuables as well as offering greater simplicity for especially higher grade feeds. In the current work, chromite ore (d80 = 290 µm) was treated using spiral concentrators and the performance of spiral concentrators was examined. The design of the separation circuit comprised of rougher, cleaner and scavenger stages. The resultant fractions produced by each separation unit and feed samples were analyzed to identify the particle sizes, mineral liberations and chromite content. Grade and recovery comparisons were presented in size-by-size manner and the separation tendency of the particles were determined in varying feed rate conditions. The overall results indicated valuable mineral loss of the plant and alternative suggestions were pointed to reach the target values.INTRODUCTION Spiral concentrators are simple low energy consuming devices, which are generally used for pre-concentration of the minerals. They are cost efficient equipment separating minerals mainly based on density differences of the minerals. The adjustable splitters remove the concentrate as the remaining stream continues to move down the spiral. Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational force, centrifugal force, hydrodynamic drag and Bagnold force (Atasoy and Spottiswood, 1995; Burt, 1984). Since the classification in a spiral concentrator depends on particle specific gravity and size, the operation of spirals can be analyzed using size recovery or partition curves (Bazin et al., 2014). Spiral concentrators possess multiple design parameters for a variety of applications. The design parameters that govern the performance of the spiral can be identified as the diameter, number of turns, slope, pitch and the profile of the trough. For an efficient separation on a spiral concentrator, the properties of the slurry flowing on a spiral, ore texture, percent solids and flow rate play important roles."

Jan 1, 2018

By N. Kumar Kittusamy

ALTHOUGH MANYSTUDIES HAVE SHOWN an association between operating heavy construction equipment and symptoms of musculoskeletal disorders (MSDs), little research has been performed that systematically characterizes the exposure of operating engineers to ergonomic hazards. This study evaluated: 1) vibration at the seat/operator interface;2) transmissibility of vibration in the Z-axis; 3) psychophysical ratings of vibration level and vibration discomfort; and 4) postural requirements of the job. Results indicate that the digging operation had higher levels of total weighted acceleration than high- or low-idling conditions. Transmissibility data showed that the seat amplified vibration, particularly in the lower frequencies. Seats demonstrated that they may not be sufficient in protecting operators from long-term effects of vibration exposure. High positive correlation was found among subjective ratings (vibration discomfort and vibration level), but moderate positive correlation was found between subjective ratings and quantitative vibration levels. Postural evaluations revealed that the operators were required to assume awkward postures of the neck, shoulder and trunk while performing their jobs. Work-related injuries and illnesses pose a continuing threat to the health and well-being of American workers. The construction industry has been historically recognized as having higher rates of fatality, injury and illness than other industries (McVittie285+; BLS). In 1994, an estimated 218,800 lost-work-day injuries were reported in the construction industry (BLS). Construction also had the second-highest incidence rate for sprains and strains. Although the industry has made progress since then, injuries and illnesses, including MSDs, continue to because for concern.

By C. E. Golson

The preparation of aggregates is a form of mineral processing which has been taken for granted for many years, mostly because of its lack of glamour when compared to the winning of metallic minerals from their ores. Many of the processes and equipment now used in the metallic mineral processing industries originated in the more prosaic preparation of aggregates. 'Their adaptation to metallurgical processes has led to developments both in their design, and in their use. Modern practice, has been so exacting in its demands that, in many cases, this improved technology is finding new applications in the very industry in which it originated the mineral aggregate industry, The low cost requirements, large tonnage capacities and complex specifications which govern the acceptability of its products have node modern aggregate processing a much different art than it was one or two generations ago. The basic conditions which govern the type and quality of mineral aggregates were presented in an addendum to a paper given at the San Francisco Meeting in 1959 by one of the authors.

Jan 1, 1961

By Karsten Zimmermann

Surface deformation monitoring is required all over the mining industry. For example oil and gas companies need this information to support exploration and production activities and to detect impacts from surface subsidence of existing hydrocarbon fields. Also opencast mines require large area information of subsidence due to dewatering of the overburden. Because of this, a lot of surface deformations measurements with GPS or traditional geodetic measurement techniques have been conduced during the last decades. This paper presents the actual capabilities to analyze GPS data using the state of the art Bernese GPS Software for GPS post processing. A new way of monitoring subsidence is a combination of GPS and satellite InSAR data. Considering this it is hoped that a combined strategy will permit receiving overall more information by integrating high point density of InSAR and accuracy of GPS. DMT is one of the leading actors on GPS services especially for monitoring surface movements from underground activities e.g. mining, water pumping or oil and gas exploitation. The paper will discuss preferences and problems of this approach on results of a current project of DMT.

Jan 1, 2008

By Don W. Deere

Faults under high rock cover represent some of the most severe ground conditions a Tunneler can encounter. High ground water pressures and flows are usually associated with mountain faults. Ground behavior can range from blocky ground to flowing sands and squeezing clays. Sticking a IBM within a fault zone for many weeks, with the disastrous financial consequences, is still a common occurrence. Interpreting the geology and detecting the location of a fault prior to penetrating it is a fundamental step to successful tunneling. Ground water control through predraining or pre-grouting is the second fundamental step. This paper discusses techniques applied for detecting and crossing mountainous fault zones through the use of case histories across the globe.

Jan 1, 2007

By A. G. Sciulli, G. P. Ballock, K. K. Wu

Waste disposal underground is the most effective method when viewed from an environmental aspect. As costs of other methods of disposal continue to escalate, the cost effectiveness of underground disposal during the mining cycle becomes increasingly attractive. The use of concrete for sealing abandoned mines has proved to be suspect when associated with a relatively incompetent adjacent strata due to its shrinkage characteristics. Complete failure of the plug has been known to occur in some instances. A more effective, cost competitive seal can be obtained using pneumatically stowed material and incorporating a polyurethane grout, which has greater adhesion characteristics than concrete. Injection of the surrounding strata and of the stowed material helps to ensure an impervious barrier and prevent the plug from moving when subject to high pressure heads. When properly placed, impervious seals cause the old workings to flood, raise the mine pool level, and thus eventually eliminate the potential for oxidation, which is the primary cause of acidity in the water.

Jan 11, 1986

By Khaled Morsy

In the past two decades, high horizontal stress has been attributed to many ground control failures. Most believe that entries parallel to the high horizontal stress is most stable and least stable when perpendicular to it. Entry stability decreases when the angle between entry and horizontal stress increases. The concept of 2-D stress shadow has been proposed for selection of proper panel orientation, often with mixed results. In this paper 3-D finite element modeling was used to analyze the stress distribution at the headgate of a longwall panel subject to high horizontal stress at various angles. It was found that the directions of induced principal stresses at the longwall face and headgate are independent of the panel orientation. The induced principal stresses concentrate or relief at headgate based on the panel orientation with respect to the directions of the induced principal stresses. Accordingly, only 3-D modeling can fully account for the effects of high horizontal stress on panel orientation. The paper illustrates in details the changes in orientation and magnitude of all three principal stresses around the longwall face and T-junction area as panel orientation changes.

Jan 1, 2006

By Steve Signer, Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs, Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads, Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. 'These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

By J. K. Lemley

The human element in large measure dictates success in contracting relationships. Because of our professional backgrounds, we view contracts primarily as either engineers, contractors or owners. A beneficial contractual environment--one in which decisions, risks and benefits are shared--demands equal consideration of all three points of view. Most of the older cities in the United States, for example, suffer from bad contracts--generalized, patched-together documents that represent an accumulation of modifications originally written to compensate for specific situations that have occurred over the years. Because such documents lack coherence, they often present conflicting instructions which lead to defensive, ultimately destructive attitudes among the parties involved in the day-to-day administration of the project. Good contract development begins with a strong central philosophy to which the details of the contract can be related. First, the owner should establish a comprehensive philosophy in which risks between the parties are identified. Following this, a specific contract document can be written to satisfy this established philosophy. The contrast between two opposed contractual situations, NYC Water Tunnel Number Three and the Seabrook Nuclear Power Plant Cooling Water Tunnels, illustrates how comprehensive, well-written contracts--contracts which share both risks and benefits--provide the basis for achieving quality construction that will reward engineer, contractor and owner.

Jan 1, 1983

By A Rantala, K Aberkrom, O Haavisto, P Blanz

More complex ore bodies with lowering grades increase the challenges of maintaining high throughput, energy efficiency and required particle size for optimal downstream processing in grinding circuits. Continuous and often rapidly changing characteristics of the mill feed requires constant focus to operate the circuit at optimal level. Modern process instruments, on-line analyzers, monitoring and process control systems provide attractive and managed options to increase the circuits’ capability to respond to the challenge, often in phases and in rather short time period. Furthermore, well instrumented and performing base level automation in the grinding circuit enables advanced process control (APC) strategies that utilize measurements from the whole circuit to stabilize and optimize production. In this paper alternatives for incorporating process measurements and controls to typical grinding circuits are proposed. The expected benefits to throughput, availability, energy efficiency and particle size stability are described in recent case examples.CITATION:Rantala, A, Blanz, P, Aberkrom, K and Haavisto, O, 2015. Increasing grinding circuit robustness with advanced process control, in Proceedings MetPlant 2015, pp 129–141 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Edward Halse, Puerto Berrio, Colombia, So. Amer. (communication to the Secretary*): The Taviche mining-district is generally known as " Taviches," being named from the two villages called respectively San Pedro Taviche and San Jero-nimo Taviche. It is so called by Jose G. Aguilera, in his paper on the Geographical and Geological Distribution of the Mineral Deposits of Mexico;' and in published reports by the late N. W. Rudston Read ;2 and by Juan de Dios Villarello3 The region is a large one, measuring about 24 miles long and 7 miles wide. Dr. Chance, in his interesting paper, tells us very little about the nature of the ores, and, with regard to the geology of the district, contents himself with observing that " the country, as a rule, consists of eruptive rocks; and no evidences of sedimentary strata appear near the mines." The latter part of the above statement is hardly correct. The formation is mainly

Jan 1, 1906