Search Documents

By D. A. Elgillani, M. C. Fuerstenau, J. D. Miller

Adsorption of lead and ferric iron on quartz and alumina is presented as a function of pH. Only the hydrolyzed species of these metal ions, FeOH++ and PbOH+, adsorb significantly on each of these minerals. Zeta potentials of quartz were measured as a function of pH in the presence of various additions of aluminum, lead, and magnesium salts. Sign reversal occurs at the pH values where significant concentrations of hydroxy complexes are formed. Models of adsorption are presented in the absence and presence of collector. The mechanism of adsorption of metal and collector species in the activation of nonmetallic minerals is still the center of considerable discussion in spite of the extensive study given this system. Until recently, the view was widely held that hydrated metal ions were responsible for this phenomenon. This fact is surprising, since it had been shown that the pH range in which flotation is effected corresponds to that in which metal ion hydrolysis occurs.' Additional support of this concept was pro vided by the work of Wolstenholme and Schulman in another system.' Later work has shown that hydroxy complexes of metal ions are the active species. These studies have also indicated that basic aqueous complexes of metal-collector may be necessary for flotation.3-7 Depending on the molecular weight of the collector, formation of these complexes may occur before or after precipitation of the metal-collector salt has occurred. Ion pair formation can occur when low molecular weight collectors are involved because relatively high concentrations of metal hydroxy complex and collector can be present in solution before precipitation occurs. This is not the case when high molecular weight collectors are used. A model of aqueous complex adsorption has been presented6,7 in which it has been assumed that adsorption occurs by the formation of water from adsorbed hydroxyl and hydrogen of the hydroxyl contained in the complex. Other authors8 have suggested that hy-droxy complexes are involved in these systems but that collector adsorption occurs by replacement of the hydroxyl of the adsorbed metal hydroxy complex with a fatty acid anion. All of these investigations have involved mineral surfaces that were negatively charged so that it is not possible to state with certainty whether hydrated metal ions or hydroxy complexes are the active species in this system. Use of a positively charged mineral should be helpful, however, since the hydrated metal ion will be repelled from this surface. On the other hand, if the hydroxy complex adsorbs by splitting out water, surface charge should have no effect because of the free energy decrease that the system will experience when water is formed. In this regard, sapphire is well-suited for study, since its surface is positively charged until approximately pH 9. Electrokinetic studies of quartz in the presence of various metal ions should also be useful in establishing the mechanisms of adsorption in these systems. That is, if the hydroxy complexes adsorb by water formation, drastic changes in the zeta potential should occur in the pH range in which hydrolysis occurs. In this view, adsorption of ions of widely different hydrolysis characteristics on both sapphire and quartz was measured. In addition, zeta potentials of quartz were measured as a function of pH in the presence of various metal ions and compared with flotation responses obtained under similar conditions. Experimental Materials and Techniques Reagent-grade aluminum, ferric and magnesium chlorides, and lead nitrate were used in this investigation. Adjustments in pH were made with reagent-grade HCl or KOH. Conductivity water, made by passing distilled water through an ion exchange column, was used in all of the experiments.

Jan 1, 1971

By John E. Rourke, O&apos

A survey of existing and developing field permeability test methods was conducted in order to identify and specify capable methods to be used in feasibility investigations or performance monitoring for in situ leaching of ore deposits. Geologic settings of leachable deposits are discussed, as well as representative techniques used for the in situ leaching operation. Subsurface investigation techniques including drilling, core recovery, and down-hole inspection methods relevant to field permeability investigations are discussed. Field experience is examined and capable field permeability test methods are identified. Specifications for test borehole preparation, test performance. and methods of analysis are given. The test methods are comparatively rated in a matrix with respect to costs ease of use, and data effectiveness' for a broad range of conditions. Well Pump and Packer test methods receive high ratings. Recommendations are made for needed developments in field permeability test methods and a comprehensive bibliography is given.

Jan 1, 1977

By Bruce Geller

The 2005 Prospectors and Developers Association of Canada (PDAC) convention continued the upbeat mood found in 2004. The global mining industry is booming due to higher commodity prices in nearly every sector. Other factors include low commodity inventories, China’s strong resource demands, the weak U.S. dollar, the very strong Euro, global uncertainties, an almost overripe investment climate for natural resources and the highest mining exploration budgets in seven years. Even unglamorous commodities, like iron, uranium and zinc, received copious attention in talks, the investors’ exchange, the core shack and in certain hospitality suites. The following impressions were gathered at the convention and enhanced by conference handouts and some abstracts that are available on the PDAC’s Web site, www.pdac.ca. At least 119 papers were presented, almost twice last year’s number.

Jan 1, 2005

By Gerald M. Ellis

ntroduction As the gold mining industry continues to develop in the Dominican Republic and Haiti, more deposits will undoubtedly be discovered that will be amenable to development. The Pueblo Viejo gold mine is currently in operation in the Dominican Republic. It has become an important component of that country's economy. Pueblo Viejo output is important to the government as a foreign currency earner. It is also said to be among the world's more successful gold mines. But, while Pueblo Viejo is successful, no other major gold discoveries have been made in recent years. Therefore, alluvial deposits of gold have caught the attention of geologists on the Island of Hispaniola. In the past four years, exploration and investigation of alluvial deposits have been initiated in both the Dominican Republic and Haiti. This type of activity is expected to continue over the next few years. Alluvial gold mining is rudimentary gold washing, done mostly by farmers. It is an old tradition, dating back at least 100 years, and is done by small, independent, or community farming villages in the mountains and plains of the Dominican Republic. Investigations in the DR Recently, alluvial gold investigations have been undertaken in well known locations of the Dominican Republic. One is in the Villa Altagracia area. Here, the terraces and gravels of the Haina River basin were examined, test-pitted, and assayed by Minera Altagracia, a local Dominican mining group. Results led to a new investigation by the state-owned Rosario Dominicana (RD), the company that mines the gold at Pueblo Viejo. Rosario tested areas previously investigated by Minera Altagracia. RD could not define the type of concentration that could justify an industrial-scale type of exploitation. The Haina River placers are located in the flats and valleys of Central Dominican Republic. They are classified as small-scale type of operations where local cooperatives can do the traditional gold washing. It is not now considered a dredgable project for a mining company. The next alluvial gold investigation was undertaken by the Dominican Department of Mines and others in an area of some 700 km2 (270 sq miles) in the northeast near Miches. Farmers have been washing gold in streams and excavating pits in various areas, particularly La Mina and have made a living. Government geologists panned several hundred streams and river tributaries. They also washed material from deep excavations. The results, however, were negative insofar as locating alluvial gold concentrations suitable for large-scale or industrial-scale exploitation. The most favorable locations were the terraces along the Jayán and Cuarón Rivers in the area of Miches. But the grade od concentration is poor. Actually, only traces of gold were found in these

Jan 8, 1986

By L. L. Newman

PUBLIC UTILITY GAS PRODUCTION IN 1802, William Murdock first used retort coal gas to light his house and the Boulton and Watt plant where he was employed. For the next three quarters of a century coal served as the principal raw material for the manufacture of city gas for general distribution. Coal continued to hold its predominant position for another half century after Prof. Thaddeus C. Lowe developed the first practical method of enriching water gas with cracked-oil vapors in an integrated operation. This position, however, was no longer maintained through the medium of direct carbonization of coal in retorts but as a result of using anthracite or coke as the generator fuel in carburretted water-gas machines. The early water-gas machines were extremely crude and the consumption of both oil and generator fuel was very high. However, the cost of installation was considerably lower than for any coal-gas system having the equivalent gas-making capacity, the labor involved was small, and the water-gas machine could be started up and shut down quickly. It thus proved very useful as standby equipment and in taking peak loads from the coal-gas plants. The flexibility of the water-gas machine, furthermore, made it possible to change the candlepower of the gas readily to suit the required conditions. Later, when calorific value replaced candlepower as the standard of gas quality, the water-gas machine was found to be equally flexible in keeping the city gas under complete and convenient control. No basic improvements were made in the Lowe carburetted water-gas process until 1898, when means were added to provide for regular reversals of the flow of steam through the fuel bed. By judicious proportioning of the quantities of up-run and down-run steam, it became possible for the operator to control the hardness and position of the clinker to a degree that previously had been unattainable. Also in 1898, the first by-product coke plant in America to supply city gas was built at Everett, Massachusetts. Later many other by-product plants, of greatly improved design and capacity, were built, but not primarily for city-gas production, chiefly because of the relatively high investment cost per unit of gas made. Cheaper plant construction has been the subject of serious study, and some progress is expected, but other factors, such as plant life,

Jan 1, 1953

By S. Torres, J. Álvarez, R. Castillo, R. Fuentes, C. Sandoval, R. Parra, Myakalwar A. K., M. Velázquez, J. Yáñez, D. Sbarbaro

Rapid analytical assessment in copper mining industry is a limiting factor for operational purposes and for the improvement of processes. The present work aims to review the analytical assessment in the copper industry utilizing emerging spectrochemical techniques such as laser induced breakdown spectroscopy (LIBS) and UV-Vis-IR Hyperspectral Sensing. LIBS is a plasma based spectroscopic method where the sample surface is irradiated by high power laser. The light emitted from the plasma contains atomic -molecular spectral information and can be detected using a simple CCD based spectrometer. UV-Vis-IR Hyperspectral Sensing is produced by the reflection of light from the sample’s rough surface in all directions and it can be collected by using an ellipsoid or paraboloid mirror arrangement. The electromagnetic radiation emitted by the samples in the UV-Vis, NIR and MIR region can be used for molecular characterization. The spectrometer splits different wavelengths through a CCD arrangement in 2D spatial and spectral dimensions, thus a hyperspectral cube of data is generated. Chemometric techniques such as principal component analysis (PCA), K- nearest neighbors (KNN), support vector machine (SVM) among others, can be applied to LIBS and Hyperspectral data for better classification and quantification purposes in copper ores. Real- time determination of elemental and mineral species used for online processing control will help to achieve the copper industry 4.0. INTRODUCTION The demand for copper mineral resources is intensely growing with the increase in population, per capita GDP, the development of new technologies and the increase in global living standard. With the rise in consumption of copper, it is important to optimize mining and metallurgical processes tending to the copper industry 4.0 (Ge, Song, Ding, & Huang, 2017). The real-time analytical assessment in the mining and metallurgical processes is a crucial part for allowing the global improvement in mining industry. The features considered for better analytical assessment are the instrumental automation and interconnection, real time results, low cost, quality in terms of accuracy and precision. Furthermore, improving recovery (extraction), timing and quality of final products avoiding environmental impacts. Some elements such as Cu, Fe, Ag, Au, Mo, S, As, Pb, Zn are important to be determined in the process control. Additionally, rapid mineral identification of few species such as CuFeS2, Cu4FeS5, FeS2, CuS, Cu2S, MoS2, Cu3AsS4, FeAsS, among other can be challenging.

Jan 1, 2019

By A P. Brown

Comparison of legal permits required for mining (as opposed to prospecting or exploration) inNew Zealand, under the Mining Act 1971 and the Resource Management Act/Crown Minerals Act 1991. Mining generally receives the same treatment as any other industrial or commercial activity.

Jan 1, 1995

By Mônica Aline Magalhães Gurgel

Este trabalho avaliou a evolução estrutural e mecânica dos ciclos térmicos realizados em uma chapa laminada a frio de aço baixo carbono com micro adição de molibdênio e nióbio destinado para a indústria automobilística, associado a classe dos aços bifásicos. Para realização do estudo foi feita a caracterização microestrutural e mecânica, por intermédio de amostras retiradas após a laminadas a frio produzidas em escala industrial, com auxílio das técnicas de microscopia óptica, e avaliação da dureza via Nanoindentador Instrumentado. Os ciclos térmicos foram feitos com o intuito de observar os processos de recuperação, recristalização, e transformação de fases no aquecimento e após resfriamento, com encharque em distintas temperaturas do campo intercrítico, via análise de dilatometria em um equipamento de análise termomecânica (TMA) em amostras extraídas da chapa laminada a frio “Full- Hard”.

Aug 16, 2017

By Juan Marcelo Rojas Arango

O refino de grão da estrutura bruta de solidificação da liga Cu-8%Sn com a adição de Cu-50%Zr (inoculante) foi estudado utilizando analise térmica e metalografia quantitativa. Os efeitos da adição de Cu-50%Zr foram analisados nas curvas de resfriamento, no tamanho do grão médio e no calor latente liberado durante a solidificação. Os resultados mostram que as curvas de resfriamento sofrem uma alteração significativa na região da recalescência com a adição do inoculante. Observou-se que adições que resultam em um teor de 0,009% de Zr na liga causaram uma redução do tamanho médio de grão de até 90%. Algumas evidências parecem indicar que o mecanismo de inoculação causado pela adição de Cu-50%Zr é o surgimento no banho líquido de partículas de ZrC, sobre as quais ocorre a nucleação heterogênea da fase Cu-a.

Aug 16, 2017

By F. P. Janse van Rensburg, P. J. Le Roux

"There are numerous factors that affect open stope stability and often result in falls of ground. These falls of ground can be attributed to factors such as beam failure due to a larger than normal roof area (hydraulic radius too large), adverse ground conditions, seismicity, the stress-strain environment, absence of support, and poor drill-and-blast practices. The effect of time on the stability of open stopes is sometimes underestimated and is relatively unknown, especially on Target Mine. Actual data was collected from open stopes at Target and analysed to show the effect of time on open stope stability. The benefits of this analysis will include improved understanding of time-dependent failure, which can assist in reducing dilution and the risk of sterilization of future mining blocks. IntroductionTarget Mine is situated adjacent to the town of Allanridge, some 20 km from Welkom in South Africa’s Free State Province, and is the most northerly mine in the Welkom Goldfields area (Figure 1). The mine consists of a single surface shaft system with a sub-shaft (Target 1C shaft) and a decline. Ownership was attained by Harmony Gold Mining Company Limited in May 2004 (Harmony Gold Mining Company Limited, 2010). Before discussing the selection of open stopes for the back-analyses, a brief explanation of open stoping as practiced at Target Mine will be given. The orebody is some 180 m in thickness and 270 m wide and comprises multiple reefs overlying one another. The 180 m thick reef package is termed the Eldorado Reefs, as shown in Figure 2. The Eldorado Reefs suboutcrop against the Dreyerskuil Reefs, as shown in Figure 3. The dip of the reef varies from as low as 10° in the west to 75° in the east.Compared with most Australian and Canadian open stoping mining operations, Target Mine is unique. In most Australian and Canadian mining operations the hangingwall and footwall of the open stopes comprise waste rock, and the orebody dips relatively steeply. Due to the depth of Target Mine, some 2300 m to 2500 m below surface, a destress slot (Figure 4) is mined to create an artificial, shallow mining environment whereby the field stress is managed and kept at values of around 60 MPa. The destress slot comprises a narrow tabular stope with an average width of 1.5 m, and is mined on the Dreyerskuil Reefs.At Target Mine the hangingwall, sidewalls, and footwall of the open stopes all comprise reef of different grades, except for the EA1, where the EB footwall is waste rock. If a stope, for example, is mined alongside an existing old stope, the western sidewall of this stope will consist of backfill. The general mining direction of open stopes is from the lowest position of the reef on the west, progressing up towards the east as shown in Figure 5."

Apr 1, 2019

By Dennis Molvik, Omar Fulton, Chris D. Breeds, Don Gonzales

This paper presents and describes the South Interceptor Parallel Phase III Contract C93012C, which involved construction of a nominal 2.7 m (9-ft) finished diameter sewer conveyance using both pipe jacking and conventional tunneling methods. Earth Pressure Balance (EPB) excavation was required to minimize the potential for settlement beneath a main rail line, overpass, sensitive wetland, areas of contaminated soils, and nearby structures. Ground conditions predicted in the Geotechnical Baseline Report included low plasticity, clayey silt (40 to 10%) and silty sand (60–90%) with pieces of wood such as logs, stumps, branches and other tree fragments. Soil cover ranged from 2.7 m (9-ft) to 5.4 m (18-ft) over the tunnel crown with a groundwater table between 1.5 m (5-ft) and 3.7 m (12-ft) deep.

Jan 1, 2003

By Andrew Thallisson de Souza

Os aços inoxidáveis ABNT da série 300 são ligas austeníticas Fe-C(< 0,08%) - Cr(18 a 20%) - Ni(8 a 10%) são muito aplicados, pois apresentam alta estampabilidade, alta soldabilidade, boa resistência à corrosão uniforme em vários meios corrosivos, no entanto, sofrem corrosão localizada (pites, corrosão sob tensão, fresta e corrosão intergranular). Os aços inoxidáveis da família UNS S32304, têm 23%Cr e 4%Ni. Por terem teor de carbono inferior a 300ppm (0,03% em massa) são resistentes à corrosão intergranular, sofrem pites e corrosão sob tensão (CST). Devido ao alto teor de cromo, o aço UNS 32304 apresenta boa resistência à corrosão uniforme, sendo que na corrosão por pites o mesmo apresenta um comportamento melhor que os aços ABNT 304 (sem Mo) e ABNT 316 (com Mo), de acordo com o Número Equivalente de Resistência ao Pite (PREN). O PREN dos aços UNS 322304 é 26, e para os aços ABNT 304 e 316 são 18 e 25, respectivamente. Este trabalho caracterizou os diferentes aços inoxidáveis química, metalográfica e eletroquimicamente em meios contendo íons cloretos. A partir de ensaios de caracterização eletroquímica, por polarização potenciodinâmica, verificou-se que o aço ABNT 304 apresentou potencial de pite inferior aos aços ABNT 316 e o UNS 32304, em soluções aquosas contendo 3,5% (massa) de NaCl. Verificou-se que estes aços sofreram CST empregando-se ensaios de deformação (corpo de prova em U) e carga constante (corpo de prova de tração liso) nos eletrodos em soluções aquosas contendo 42% (massa) de MgCl2 na temperatura de aproximadamente 143°C. Salienta-se que o comportamento em CST do aço ABNT 304 foi inferior aos demais. As amostras ensaiadas foram caracterizadas fratograficamente (macro e microfratograficamente - empregando-se microscopia eletrônica de varredura). Os corpos de prova que sofreram CST apresentaram facetas de clivagem e “marcas de rios”, características da fratura frágil.

Aug 17, 2017

By William A. Beck

This report describes the loading and transportation practices employed at the zinc-lead mines of The Eagle-Picher Co., Jo Daviess County, Ill., and Lafayette County, Wis. The report also gives a brief history of the Illinois-Wisconsin zinc-lead district and the operations of the company in the area. The diesel-powered, rubber-tired loading and haulage equipment is described and illustrated from the operational point of view only, and an analysis is made of the materials-handling system without going into health and safety Factors. The costs per ton of the various components of mechanical loading, underground haulage, underground crushing, and hoisting for fiscal year 1960 are tabulated.

Jan 1, 1964

By G. E. Blight

Wind erosion can be a major cause of the loss and dispersion of tailings material from a tailings dam into its surrounding environment. Such dust dispersion can be a serious nuisance, as well as a health hazard to inhabitants in nearby settlements, and can also damage the health of animals, degrade crops, making them less marketable, and cause soil and water pollution. The problem of wind erosion can affect tailings dams in all types of climate, but becomes worse as climatic aridity increases. Because clouds of dust are often observed billowing across the top surfaces of tailings dams in dry windy weather, there is a common misconception that the dust arises from wind erosion of the top surface. As a result, much effort and money is vainly spent on treating the tops of tailings dams to prevent dust generation, whereas the slopes of the dams are the true major dust source. This paper briefly reviews what is known of erosion of tailings dams and then proceeds to describe the mechanics of wind erosion in general, and how it affects tailings dams in particular. Finally, recommendations are made for mitigating wind erosion of tailings dams and the resulting blowing dust.

Jan 1, 2007

By Yan Beygelzimer, Alexander Spuskanyuk, Victor Varyukhin

"The main idea of the report is that the yield surface can be presented as thick, ""foamed surface"" with dimensionality exceeding two. By other words, perhaps, the yield surface is fractal, i.e. it belongs to the class of geometric objects with fractional dimensionality. Apparently, fractal structure of the yield surface is determined by the fractal structure of natural materials. ""Cloud of internal stresses"" term is introduced to describe the stress distribution in representative volume element. Its plastic flow is determined by the interaction of this cloud with the thick yield surface. Thick yield surface and internal stress cloud concepts allow to determine an additional correlation between micro mechanical models of polycrystals and phenomenological theory of plasticity.1. IntroductionClassical plastic flow models are not satisfying the modem requirements. There are two main directions in their development. The first, mathematical, is connected with the development of the general theory of rheological relationships; the second, physical, is connected with the development of the representative volume element (RVE) models which are based on specific ideas about deformation mechanisms. Within the framework of the first direction, the macroscopic experimental data is formalized; the second approach deals with the generalization of physical research results for the different scale levels that are involved in plastic deformation.These approaches have advantages and disadvantages. In phenomenological theories, the advantages are the mathematical simplicity and laconic formulation of constitutive relations, which allows using them in practical calculations. However, the mathematical models of this class can not be considered as general, they are useful only for the description of limited range of deforming processes. On the other hand, physical theories that are based on the description of real plastic deformation mechanisms are very explanatory and predictive, but they lack mathematical simplicity. The above circumstances lead us to the necessity of compromise that can be found in determining the constitutive relations for RVE, which structure and parameters would bear the information about rnicrolevel and mesolevel phenomena. In this synthesis direction, the fundamental role belongs to [1,2], etc."

Jan 1, 2001

By J. F. Curtis

In the synopsis, the author concludes that ?high levels of seismicity do not coincide with high rockburst rates?. Implicit to an appreciation of this statement is the necessity of a common understanding of what is understood by the terms: ?high level of seismicity? and ?high rockburst rates?. With respect to the former term there is no difficulty in that the level of seismicity is traditionally measured in terms of the Richter Scale. The latter term however presents a problem in that the author defines it as a particular sort of seismic event?viz: ?Rockburst? is understood as a seismic event that causes damage to an underground excavation with subsequent injury, loss of material/equipment or production shifts? (p. 322). No scale is given of the amount of: ?excavation damage ?level of injury ?material/equipment loss ?production shifts lost whether separate or cumulative, for a particular seismic event to be classified as a rockburst. A further difficulty arises in that in common usage the words ?rockburst?, ?seismic event? and ?earthquake? are all used to describe the same event.

Jan 1, 1999

As a bubble travels through the pulp region of a flotation cell, it will collect the most hydrophobic particles of an intermediate particle size range, this being the primary source of true flotation selectivity. Despite its role on bubble-particle attachment, however, particle hydrophobicity is still missing a mathematical definition that can be used for plant simulation. In this paper, particle hydrophobicity is defined in terms of the induction time necessary for attachment and then linked to the mass of collector adsorbed per particle. This allows particle hydrophobicity to be written as a function of density of collector adsorption as well as particle size and mineralogy. The model is calibrated from the experimental measurement of the flotation rate constant. Liberation data from an industrial flotation rougher is used for model validation. It is demonstrated that the model can describe a broad experimental dataset by means of a minimal number of parameters. Main industrial application is in simulating the effect of the chemical environment upon plant metallurgical performance.

Jan 1, 2006

By A. E. Wraith, N. J. Petch, J. D. Embury, E. S. Wright

The two most important parameters controlling the fracture behavior of a solid are its intrinsic properties, e.g.,grain size, and the operative stress system. The latter may be modified in laminates by the presence of weak interfaces. This is studied in notch-impact tests on a mode1 system of mild steel laminates containing a variety of interfaces. The effect of these is evaluated in terms of the ductile/cleavage transition. Two laminate geometries are distinguished, here called "crack-arrester " and "crack-divider". In both, cleavage is inhibited. This arises because of relaxation of a state of triaxial tension. In the crack-avrester laminates, cleavage initiated at a notch is confined to the layer containing the notch. In crack-cliuider laminates, a thick specimen behaves as the Sum of a number of thinner ones. Additional benefit may derive from improved intritnsic propevties of- the lanlinate layers arising from greater deformation in their manufacture. It has long been recognized that the two most important parameters controlling the fracture behavior of solids are their intrinsic properties (e.g., grain size friction stress,3 distribution of second phase particles4) and the operative stress system under which fracture occurs. In solids that show a ductile/cleavage transition, cleavage is favored by the presence of a notch. This is because triaxial tensions, generated by the localized plastic constraint at the notch, are operative when fracture occurs.= Anything that suppresses these triaxial tensions will be unfavorable to cleavage. Such suppression may possibly occur in laminates containing weak interfaces and the purpose of the present paper is to explore this possibility. Two basic laminate geometries, here termed "crack-avrester" and "cvack-divider", are examined. They are illustrated in Fig. 1. With the crack-arrester laminates, there is the possibility that, when the fracture crack approaches the interface, this, if weak, may delaminate due to the tensile stress acting parallel to the plane of the crack.= If this happens, energy will be used in delamination, the crack will be completely blunted, and the triaxial tension associated with the crack will be relaxed. To fracture the second portion of the laminate, crack reinitiation will be necessary and, because of the relaxation of the triaxial tension, this reinitiation will occur under conditions of nearly uniaxial tension, which are unfavorable to cleavage. Thus there is the possibility of cleavage suppression in the second and subsequent subunits of a crack-arrester laminate. With the crack-divider geometry, there is again the possibility of delamination at the interfaces. This will divide the crack into a series of cracks propagating through the individual laminate subunits. If these are sufficiently thin, the triaxial tension will be relaxed towards a state of biaxial tension in each of them. Thus, with the crack-divider laminates, there is again the possibility of cleavage inhibition. In the present work, these possibilities are explored using a notched impact test on mild steel laminates bonded with soft solder, silver solder or copper. Even if delamination does not occur, it is still possible that cleavage may be inhibited in laminates. With the crack-arrester geometry, the cleavage crack in the first layer may be blunted and arrested by plastic deformation in the laminate bond, if this is ductile. Partial relaxation of the stress transmitted ahead of the crack into the second layer will then result and this will reduce the significance of this stress in the fracture of the second layer. With the crack-divider geometry, there cannot be much effect in the absence of delamination unless a large amount of energy is absorbed in rupturing the ductile material. EXPERIMENTAL DETAILS The composition of the mild steel (wt pet) was: 0.04 C, 0.29 Mn, 0.01 Si, 0.006 P, 0.008 S. "As-received" plate was annealed for 2 hr at 900°C and slowly cooled to give a grain size of 0.04 mm. The laminates were made by brazing or soldering together mild steel plates 8 by 3 in. by various thicknesses. These were obtained from the annealed plate by machining, so that the intrinsic material properties were .kept constant. Laminates containing two to six steel layers were studied using standard Charpy V-notch specimens cut from the bonded plates. Standard homogeneous specimens from the annealed plate and subsize ones from the laminate components

Jan 1, 1968

By M. H. Childs, K. E. Merklin

Blast furnace feed specifications are being revolutionized because of the large increase in iron pellet production from low-grade ores of the Lake Superior region. Recent laboratory findings aimed at a better understanding of factors influencing the physical quality of pellets produced from taconite concentrates are reviewed. Tests for determining better product quality, the effects of additives, and production factors are discussed. The current revolution in specifications for blast furnace feed is typified to a great extent by the recent tremendous growth in iron ore pellet production from low grade ores of the Lake Superior region. Indeed, pellets are responsible, at least in part, for many of the stringent new requirements that are being placed on the suppliers of furnace raw materials. As the tonnage of pellets going to the steel mills increases, more and more attention is being turned to the detailed characteristics that make this product an ideal blast furnace feed. Control of quality in pellets is similar to that of any other product. A basic understanding of the factors that are encountered in their production, from the crude ore through to the finished product, is required, along with careful process supervision and frequent quality checks. Normally, chemical grade is not a problem. This usually can be controlled within the desired specifications by minor operating variations in the con- centrator. While future changes in requirements may result in the need for self-fluxing pellets1 or other chemical changes, today's quality demands center primarily around the physical characteristics of the pellets. It is in this area that many of the recent laboratory studies have proven helpful to the operating plants. A better understanding of the physical factors involved in pelletizing has provided the basis for a continuing program of quality improvement. Tigerschiold and Ilmoni2 and Cooke with various associates are responsible for the development of much of the basic understanding of the pelletiz-ing process. These earlier findings have served as a most useful background for this work. LABORATORY PROCEDURES Magnetite concentrates produced from eastern Mesabi Range magnetic taconites were used for all of the work reported herein. The sizing and chemical analysis of a random sample are shown in Table t Additives usually are mixed with the concentrates in taconite plants before pelletizing to improve the strength characteristics of the unfired balls. Ben-tonite, soda ash, and coal are in common use. The bentonite used in these studies was of the Wyoming sodium type; the soda ash was a standard commercia1 brand. Anthrafines were used where coal was called for. The procedure for making batches of balls at the Hibbing Laboratory is as follows: In an especially designed mulling equipment 2800 g of dry ore are mixed for 10 min with the desired additives. Water is added and mixing continued for 1 1/2 min. The charge is removed from the muller and put through a mechanical shredder to break down any lumps that may have formed. sixty previously formed seed balls are placed in the balling drum, which is in fact a 6 x 16-in. diam airplane tire turning at 53 Wm. Two thousand grams of the shredded concentrate and additive mix are fed by hand into the tire at a con-

Jan 1, 1961

By J. Gordon Parr, D. H. Polonis

IN a previous study of hypereutectoid Ti-Ni alloys' a substructure was observed in quenched powder specimens when the constitution was 100 pet retained ß body-centered-cubic phase. The alloy powders were quenched from 1000°C by a blast of helium gas and precautions already described were observed throughout the work, to minimize contamination. Ogden et al.2 have previously observed subboundaries in the ß phase of a Ti-Mn-N alloy; but this structure was attributed to nitrogen-rich a precipitation. The nitrogen content of the Ti-Ni alloys does not exceed 0.02 pet and the quenching rate was sufficiently rapid to suppress precipitation reactions. Since X-ray diffraction results have confirmed the absence of any second phase which might account for this phenomenon, it seems unlikely that this substructure is explicable in terms of nitrogen content. Fig. 1 shows the substructure in adjacent grains of 100 pet ß phase in a quenched 6 atomic pet Ni alloy. Fig. 2 shows adjacent ß grains in a similarly treated alloy; one grain contains marked intracrys-talline boundaries and the other is completely free from any substructure. The suberystals appear to have fairly regular shapes, suggesting a regular orientation relationship among them. Tempering the retained ß structure at temperatures below the eutectoid eliminates the substructure at an early stage of ß decomposition. At the present time it is possible only to guess at an explanation for this subboundary phenomenon, since very little work has been reported on substructures resulting from phase changes. It is believed that the present phenomenon is due to poly-gonization resulting from unrelieved stresses set up

Jan 1, 1957