Search Documents

Mond gas-producer tar, and, in fact, all tars obtained from the retorting of coal where steam and air are admitted to the retort, are of entirely different chemical composition to the ordinary coal tar made in the gas or coke works. These tars contain none of, the aromatic hydrocarbons - benzene, toluene, naphthalene, and anthracene, sought after by the ordinary coal-tar refiner.The distillation of Mond tar shows it to consist of phenols of high molecular weight, unsaturated hydrocarbons of high gravity and low viscosity, paraffin wax, and resinous substances of whose composition little is known.The physical properties of Mond producer tar are also peculiar. It has a "short," granular texture when cold, which might be likened to candied honey. It "dries" (hardens) when exposed in thin layers to the air, and, for a coal tar, it cannot be considered sticky. This latterò property, combined with the short texture, prevents its being used successfully for road-making or macadamizing.The drying properties and the paraffin wax contained in: this tar cause it to hold up large percentages of water, probably in the form of emulsion. When containing as much as 10% to 15% moisture it appears to be quite dry.

Jan 1, 1918

By Larry D. Wayland

Almost 100 sedimentation ponds were conceptually designed for a large surface mining study area in northeast Texas. An approximate procedure was developed to economically estimate construction quantities in order to predict surface water control costs. This procedure utilized site-specific empirical relationships developed from detailed analyses on a representative number of proposed sedimentation ponds. Use of these equations provided earthwork volumes, and spillway pipe lengths. The procedure developed for this study is presented along with the results of a verification analysis.

Jan 1, 1983

By Harry H. Power

WHILE the attention of all engineering branches is focused today on changes and improvements in the several curricula, we are concerned here with the many questions arising in industry and college concerning the preparation for the petroleum engineering profession. The succession of problems confronting the petroleum engineer demands a degree of versatility not ordinarily encountered in other professions. As a consequence, the student cannot acquire mastery of all the several engineering branches represented in field practice, and as an alternative, he has learned to appreciate the value of thorough training in the basic or fundamental sciences as a preliminary foundation for professional work. While our attention is directed primarily to the training of engineers in educational institutions, it is necessary that the ultimate education of the professional engineer be kept in mind. It is apparent that his success as an engineer is limited not only by his educational and job experience, but by his native endowments: mentality, personality and health. The engineer's lack of job experiences often proves as much a handicap as the lack of adequate college training. If the final product proves to be satisfactory, both industry and technical institutions are to be congratulated. However, if the product is found wanting, the one most responsible should be apprehended. FITNESS FOR PROFESSION For the most part, students of engineering colleges have had their interests in applied science awakened at a relatively early age. Many of them entered college as a convenient means of acquiring a technical education, but undoubtedly would have had better prospects in a shorter program offered by institutions of noncollege grade. The activating motive of practical interest is also strong in students suitable for college training, but in many cases an intellectual interest must be awakened in order that it may survive graduation. Numerous engineers believe that this progressive process of selection and determination of career aims is one of the essential services rendered by the engineering colleges. Industrialists, who are more interested in quality than quantity of petroleum engineering graduates, have pointed out the good that should result if more emphasis were given to the work of eliminating the misfits. They also point out the protective measures that have been taken by other professions for the betterment of professional standards. Mention has been made of the beneficial results to be obtained by collective determination of the market for the products of engineering schools, particularly in that the students unsuited to the profession would have an opportunity to prepare themselves for employment more suited to their personalities and other qualifications. In the event that such a system of coordinated personnel direction is developed by the

Jan 1, 1941

By Lucien Weber

In the Shanghai area, the soil conditions are such that bearing piles have become an essential foundation part of the new highrise buildings. In order to reduce the settlements under the high working loads of about 2300 kN/pile, the Chinese building authorities require the pile tip to penetrate into the compact sand layer, situated at approx. 60-70 m depth. No H-piles have yet been tested under these conditions in Shanghai. This paper describes the driving of 8 H-bearing piles with 4 different shapes and with lengths varying from 45 to 75 m. Dynamic measurements are performed during driving and after a wait time of approx. 40 hours in order to assess the change in bearing capacity in function of time and in order to get an idea about the resistance distribution along the piles by using a stress wave analysis program (CAPWAP). One pile is equipped with channels between the flanges for executing verticality measurements with an inclinometer. However, this test has not yet been performed. One month after driving, two piles of 75 m length are statically loaded both in vertical and in horizontal directions.

Jan 1, 1987

By Darelle T. Janse van Rensburg

Some of the more recent developments in Paint Technology are solvent free materials. These coatings have mainly been formulated to overcome the negative attributes of solvent-based coatings, i.e. environmental, safety and health risks, potential for solvent entrapment and osmotic blistering, as well as the formation of micro-pores during the curing process. Two solvent free liquid epoxy coatings have been used extensively on power generation plant. However, very little is known regarding their long-term performance under different exposure conditions, as well as whether these coatings actually perform better than their solvent-borne counterparts. In addition, solvent free materials are generally used where outage periods are restricted and coatings need to be applied within a very short period. Though these materials have reportedly much shorter curing times than other conventional solvent-borne coatings, little is known regarding their limits with respect to maximum film thicknesses and being put into service while still being wet/partially uncured. The latter has become common practice at many power stations in the past two years or so. In addition, the application and curing methods of solvent free materials are different to that of solvent-borne materials, and may require equipment and application process changes. This paper covers the application and performance properties of solvent free coatings in comparison to solvent-borne materials primarily intended for immersion service. Numerous coatings were evaluated under immersed static and cyclic hydrostatic pressures. Other tests included short curing / early immersion tests, dry-to-touch and dry-through curing times, adhesion tests, surface tolerance tests, etc. The results show that the solvent free materials have clear benefits with respect to safety, health, environmental and long-term performance, but will be more difficult to apply compared to solvent-borne materials.

Jan 1, 2006

By B. N. Das, P. A. Beck

THE o phases have a complex tetragonal structure with Lo/ao = 0.52 and 30 atoms per unit cell.1 A large number of such phases are now known to occur in various binary systems of the transition elements and they exhibit the following typical features: 2,3 The composition of binary o phases is variable, ranging from approximately A4B to ABI. With only a few exceptions, in the o phases the A-ele-ment comes from the V- or Cr- group of the periodic table, while the B-elements are from the Mn-, Fe-, Co-, or Ni- group. In the first long period the corresponding o phases of the V- and Cr-series have approximately the same compositions. However, as the B-element changes from Mn to Fe to Co to Ni, the mean composition shifts monotonously toward higher A-contents.2-4 For example, if the mean compositions of the various o phases with vanadium are compared with each other, the composition shift mentioned above becomes plainly visible: V 30Mn0 80 Vo.45Feo..,, Vo .,Coo. 45 and Vo.5Nio.3. Similiar composition shifts, although not the same composition values, were observed in u phases formed by second and by third long-period transition elements.3'4 This behavior, very characteristic of o phases, is in rather sharp contrast to the usually quite well-behaved stoichi-ometry of the Laves phases. In the latter, the AB2 stoichiometry predominates, with A the large atom and B the small atom.= The p phase occurs in the four binary systems of Mo or W with Fe or Co. On the basis of their crystal structure determination, Arnfelt and westgren6 ascribed to the p phase in the Co-W system the ideal composition W,Co7. Since all four binary pphases have nearly the same composition, it would seem quite plausible that some definite stoichiometry such as A6B7, might be characteristic of this phase, as AB2 is of the Laves phases. On the other hand, it has been noted,7 that the phases occur at average electron concentrations near to those at which the various cr phases are found. Also, it has been pointed out by Shoemaker and associates8 that structurally the a phases and the p phases are somewhat related to each other; both of these structures may be described in terms of suitable stackings of quasi-hexagonal layers'of atoms. By studying a suitably chosen ter- nary phase diagram, one might expect to be able to find out which one of the two conditions, the analogy with the o phase or the constant ratio between the number of large atoms and the number of small atoms in effect governs the behavior of the p phase. Several isothermal sections of ternary systems containing o phases have been investigated. In all cases where two binary o phases occur, these were found to be connected b a more or less straight ternary o phase field.7' '10 Such elongated o phase fields were also found in ternary systems in which only one of the limiting binaries is known to contain o phase. In this manner a latent o forming tendency could be detected and the virtual composition of a "binary o phase", which does not actually occur as such was approximately determined by extrapolation. The behavior of the phases, including their composition shift, is analogous to that of the classical electron compounds, as described by Hume-Rothery.11 In order to decide whether the p phase is essentially a "size compound" like the Laves phases, where a fixed stoichiometric ratio is quite generally maintained between the "large atoms" and the "small atoms", or whether the p phase is typically an "electron compound" in the same sense as ois, it was decided to investigate an isothermal section of the Mo-Mn-Co system. The Mo-Co system12 and the Mo-Mn system13 each are known to have a binary o phase. It could be therefore expected that a ternary o phase field will connect these two binary cr-phase fields. The p phase is known to occur in the Mo-Co system. If the p phase should turn out to form an elongated phase field extending deep into the ternary system, the following considerations mighto apply. The atomic radius of manganese (1.314for C.N.12) is between the va,lues for Mo (1.40Afor C.N.12) and for Co (1.26Afor C.N.12). If it is assumed that p is a "size compound", and that Mn is substituting for the smaller Co atoms in the p-structure in the ternary system, the y-phase field might be expected to extend parallel to the Mn-Co binary line. If Mn is substituting for the large Mo atoms in the p-structure, the p-phase field may be expected to extend parallel to the Mn-Mo binary line. On the other hand, if the p-phase turns out to be an "electron compound" like o, the ternary p-phase field should extend parallel to the ternary o -phase field connecting (Mo,Mn)owith (Mo, Co) a

Jan 1, 1961

By R. D. Saltsman

This report is in fulfillment of Contract No. H023001.5 awarded to Bituminous Coal Research, Inc., on November 15, 1972. The scope of the work under this contract was to perform a two-phase survey for the purpose of determining the status of work in the following specific areas of industry needs under the Technology Transfer Program and to increase industry's awareness of research efforts under the Federal Coal Mine Health and Safety Act of 1969 6f (P.L. 91-173): 1. Research and development of respirable dust sampling instruments which will more accurately collect the respirable Cuss as defined by the Federal Coal Mine Health and Safety Act of 1969. 2. Development of a better means of control of respirable dust and float dust.

Jan 1, 1973

By Karen Dawson, Qiang Li

Unreinforced displacement augercast piles, or rigid inclusions (RIs), were installed for foundation support of a combined sewer overflow treatment building. The RIs penetrated loose silty sand and soft silt and terminated in medium-dense to dense silty sand, approximately 40 ft below grade. The building houses water-holding basins and level-sensitive weirs and equipment. Strain gage-instrumented static axial load tests and low strain pile integrity tests (PIT) were conducted on the RIs as part of quality control for this technology. Strain gage monitoring continued during the installation of the remaining production RIs, construction of the building, and water preloading of basins and channels within the building. While the composite RI-reinforced ground and load distribution mat system performed as expected for settlement control and was not needed for lateral support, RI fractures as observed by PIT in this project might need to be controlled in other situations. Case history information regarding the subsurface fill and deltaic deposit character, RI installation production rates, RI testing procedures and results, and construction settlement monitoring are presented.

Oct 31, 2023

By R. W. Drier

THE conductivity of copper wire is of prime importance to the electrical industry and consequently to the copper refiner and wire manufacturer. Annealed copper wire has a higher conductivity than hard-drawn wire, but, on the other hand, its tensile strength is lower. In an attempt to explain the reasons for these changes in property or at least to study the conditions existing in these two types of copper wire, the experiments described here were carried on in the Department of Metallurgy of the Michigan College of Mining and Technology. This is only a partial and preliminary report on some of the work done to date on a research program of which the object is an intensive study of copper. It is offered with the hope that, though it is not an exposition of the most rigorous of conclusions, the general trend of inferences which may be drawn will be of value and interest.

Jan 1, 1929

By W. A. Heitbrink, J. D. Ashley, R. E. Gresh, J. A. Organiscak, A. B. Cecala

Many different types of mobile equipment used in surface coal mining utilize enclosed cabs to protect equipment operators. The overburden removal process is extremely dusty and can cause excessive exposure to respirable dust, especially crystalline silica. After equipment is used for years, many components of the enclosure deteriorate and its effectiveness is greatly reduced. This report discusses a cooperative research study performed on an Ingersoll Rand DM45E surface drill, retrofitted with a new Sigma pressurization and filtration system. Respirable dust concentrations were substantially reduced from 0.64 mg/m3 during pre-testing to 0.05 mg/m3 during post-testing with the new system, representing a 92% reduction in dust levels in the drill cab. This new system appears to be a very well-built and sturdy device, well-suited for the mining industry.

Jan 1, 2002

By Javier A. Llano

GPS, wireless communications and on-board and off-board computing capabilities provide today’s mining companies with unprecedented process improvement and cost reduction opportunities. All aspects of the operation from engineering, surveying, drilling, loading, hauling and support can benefit from products like CAES and Drill Monitor. These technologies, which have been working at world class mines around the world in some cases for over three years, are helping customers achieve new lows in cost per ton. Manually intensive and time-consuming processes like in field surveying are replaced by timely mine status information wirelessly transmitted from the machines to the office.

Jul 17, 2000

By George D. Raitt

Anyone who has spent any time in and around the drilling and blasting profession knows that probably the most critical part is the drilling portion. A blasthole is nothing more than a cylindrical vehicle designed and strategically situated to hold and contain an explosive charge so that it can be detonated in the most efficient and optimum manner possible. It matters very little if the latest “State-of-the-Art” explosive or detonation system Is employed if the hole is poorly placed; i.e. excessive burden and spacing, sized incorrectly for desired results, insufficient in depth etc.. This is not to mention that the drilling phase is the most expensive, requiring sizeable initial outlays and upkeep. It’s also true that improper drilling can cause costs to skyrocket throughout the remainder of the work cycles such as excavating and hauling, crushing, screening and so on.

Jan 1, 1990

By R. Grant, C. Bazin

"Brunswick Mining has investigated grinding media optimization for the purpose of improving the flotation feed and regrind product size distributions to enhance metal recoveries. This paper presents the findings of on-going testing of various sizes and shapes of grinding media. Plant observations combined with estimated breakage rates demonstrate the importance of appropriate selection of media sizes on the milling operation.IntroductionBrunswick Mining and Smelting is located near Bathurst, New Brunswick, and operates one of the world's largest lead and zinc mines. The ore mineralogy and processing flowsheet have been described elsewhere (Petruk and Schnarr, 1981; Shannon et 01., 1993). Despite the 25 years' milling experience, there has been considerable disagreement as to the required grind size (Grant et 01., 1991). Since 1964, fineness of the flotation feed ranged from 60% to 80% passing 400 mesh (37 um) and averaged slightly above 71% in 1992. Results from mineralogical analysis (Petruk and Schnarr, 1981), laboratory and pilot plant experiments, as well as plant sampling (Grant et al., 1991; Hendriks and Ounpuu, 1985; Shannon et al., 1993) indicate that improved metal recoveries can be achieved by an increase in the fineness of grind, and more specifically by maximizing the amount of material in the 15 urn to 25 um range.This paper shows the results obtained so far from the evaluation of the effect of grinding media size and shape on grinding mill efficiency. The problem of finding optimum grinding media size, shape and composition has been recogrtized since the early 19405. The main criterion for the selection of media size is the size of the material to be ground (Bond, 1958). Although several relationships have been proposed to assist in the selection of grinding media size, none of them are entirely satisfactory (Wills, 1988). Other approaches using the breakage rates and process simulators were developed to help in the selection of grinding media size (Austin et al., 1976; Lo and Herbst, 1986; Concha et 01., 1992; Samskog et al., 1990; Martinovic et al., 1990). Although considerable effort was put into the analysis of grinding media size, very little information is available on the effect of grinding media shape (Norman and Decker, 1985, p. 3C-4). Norris (1952), Kelsall et al. (1973) and Herbst and Lo (1989) have shown that balls are more efficient than other shapes of grinding media including truncated cones and cubes."

Jan 1, 1994

By M. E. Holuszko

Although there is no widely accepted rigorous definition of handleability, the handling coal characteristics often referred to as handleability define whether a coal has the ability to flow unhindered through the processing and transportation systems. The handleability may be severely affected if fine coal particles tend to aggregate. In the pelletization process, the rolling action of the drum is applied to bring the individual particles into proximity with each other so that they can aggregate and form pellets. Because of apparent similarities between these two processes, the pelletization tests are carried out in parallel to the handleability tests in this project, and the pelletization results are used to explain coal handleability properties.

Jan 1, 2004

Case I- Timber Pile Test- 4 pages describe the pile driving record, the pile load test and the boring log. Case II- 24 inch square prestressed concrete pile-5 pages give details about the pile driving, the boring log, the pile driving record, and the pile load test. Case III- 12 inch square prestressed concrete pile- 5 pages describe the compilation of SPT blow counts for the whole project, the pile driving record, the pile load test and the detailed boring logs. The 70 foot long pile was driven by a Vulcan 08 pile hammer. Case IV- 12 BP 53 Steel H pile- 3 pages give the pile load test, the pile driving record and the nearest boring log. The 64 foot long pile has its tip at elevation 908 ft. and the ground is at elevation 972 ft. The contractor augered to elevation 959 ft. before driving the pile with a Conmaco 08 single acting pile hammer. The hammer had an 8000 pound ram, a rated energy of 26,000 ft-1b., and a 7 1/2 inch thick asbestos cushion. Dynamic measurements were made during driving of the test pile and measured a hammer energy equal to 12,500 foot-pounds.

Jan 1, 1988

The design of excavations in high displacement mining environments requires consideration of both the load and displacement capacity of the ground reinforcement and support systems. This paper is a case study on the design of point anchored rebar bolts using laboratory tests and field trials at the Ridgeway Deeps block cave. A laboratory testing program was carried out to measure the mechanical properties of the Strata Control Systems R27 Secura resin bolt which is currently being installed on the extraction and undercut level at the Ridgeway Deeps block cave. The aim was to quantify elastic, plastic and energy parameters for various bolt, mesh and plate systems. Experiments were performed on bar segments, bolt/plate systems, and bolt/plate/mesh/resin systems. The mechanical properties were calculated from tensile tests with a 500 kN Avery machine. Load-displacement data was collected from four different testing configurations. The laboratory results are compared with underground measurements and observations of bolt performance.

Nov 25, 2010

By Rômulo Albertini Rigueira

A fratura por fadiga é a forma mais comum de falha estrutural e, atualmente, é um problema desafiador no projeto de componentes mecânicos. O objetivo desta pesquisa foi modelar matematicamente as curvas de crescimento de trinca por fadiga em função do fator de intensidade de tensão de uma junta de aço 1016 obtida pelo processo de soldagem GMAW. Os resultados obtidos no estágio II da curva de propagação de trinca por fadiga mostraram que o material respeita a equação de Paris para solicitação no sentido longitudinal. No entanto, verificou-se uma correlação linear entre os parâmetros. Esta correlação deixa de existir quando se trabalha com o modelo de Bergner. Não houve variação no crescimento de trinca por fadiga na direção TL, analisado segundo o modelo de Bergner e na região fundida.

Aug 16, 2017

By Jayna Kátia Dionisio dos Santos

Os materiais compósitos tornaram-se ao longo dos últimos anos, essenciais ao surgimento de novas tecnologias. Para tanto, é imprescindível que alguns cuidados sejam considerados ao desenvolver estes materiais, como o uso do processo de fabricação adequado e a aderência fibra/matriz, sendo este último um fator preponderante na resistência mecânica final do produto. Também se torna cada vez mais necessário o desenvolvimento de materiais com capacidade de utilização ecologicamente correta. Diante disso, foi fabricado um compósito parcialmente ecológico, utilizando como reforço um tecido de sisal, e como matriz resina poliéster. Ainda, buscando a melhoria da aderência fibra/matriz foi efetuado um tratamento com Hidróxido de sódio (NaOH) a uma concentração de 3% no reforço de sisal. Para a caracterização mecânica do compósito, foram realizados ensaios de tração uniaxial nas fibras tratadas e não tratadas, bem como nas lâminas que utilizaram estas fibras como reforço, mediante a norma ASTM 3039. Quanto a esta propriedade mecânica, foi observado que o tratamento químico superficial diminui expressivamente a resistência à tração da fibra e, em contrapartida, aumentou a resistência do compósito polimérico quando comparado ao que utilizou fibra não tratada, confirmando assim o efeito positivo do tratamento na superfície do reforço de fibra natural.

Aug 8, 2018

By S. Al-Hassan

The deposit has been exploited for Mn oxide and carbonate since 1916. Known reserves of MnO, however, are almost depleted and the survival of the mine will depend on the exploitation of the carbonate. Kriging, inverse distance weighting (IDW) and cross-sectional methods have been applied to the evaluation of the carbonate resources and reconciliation of the estimates obtained shows that kriging and IDW give almost identical block values. A comparison using conditional probability indicates that there is virtually no difference between the global reserve estimates derived from the cross-sectional and kriging methods. The physical causes of these similarities are highlighted and the problems of dealing with multimodal distributions are discussed together with the difficulties of semi-variogram modelling

Jun 19, 1905

By Jan M. Peter

Many of the Pb-Zn massive sulfide deposits of the Bathurst area in northern New Brunswick, Canada, are intimately associated with laterally continuous iron formation (IF) (Figure 1). This IF is a fossil laminated, exhalative, chemical sediment. Together, the IF and the Brunswick #12, Brunswick #6, and Austin Brook deposits (rightmost discontinuous horizon on Figure 1) are collectively referred to as the "Brunswick Belt". To date we have only studied the Brunswick Belt and have not examined the horizon along which the QSR, CNE and Flat Landing Brook deposits lie. The Bathurst area is underlain by the Tetagouche Group (Figure 2), a Cambro(?)-Ordovician sequence of metasedimentary and bimodal metavolcanic rocks that was intruded by mafic to felsic plutons and subsequently deformed during the Taconic Orogeny. The stratigraphic sequence consists of shales and greywackes that are overlain by carbonaceous shales and felsic volcanic and volcaniclastic rocks; these are in turn overlain by mafic volcanic and sedimentary rocks. The massive sulfide deposits and IF occur within the upper portions of the felsic volcanic rocks in close association with carbnaceous metasedimentary footwall rocks (Figure 2).

Jan 1, 1993