Search Documents

By David Newman

In Eastern Kentucky, the Darby seam has had an extensive history of coal bumps and pillar bursts. The combination of high overburden, strong rock and coal, subjacent and superjacent mines, and retreat mining has produced incidences of violent pillar failure. The influence of these factors on pillar stability and the potential to bump is illustrated in two case histories. In the first case history, a bump occurred unexpectedly during the retreat mining of a five heading continuous haulage panel. Alternative cut sequences and pillar dimensions were analyzed to identify a geometry that would reduce the potential for future coal bumps or bounces during retreat mining. The viability of the alternatives was constrained by the reach of the continuous haulage system, the overburden depth, and the presence of thick sandstones in the main roof. Each alternative was numerically modeled cut-by-cut to examine the mechanism of stress transfer, as a pillar row is retreat mined. This approach highlighted which cuts were being made in highly stressed portions of a pillar and therefore more prone to coal outbursts. Validation of the numerical modeling was accomplished by comparing the cuts where bumps and outbursts had occurred underground to the highly stressed cuts shown within the models. Recommendations of the barrier pillar width between adjacent panels, pillar dimensions, and changes in the retreat mining sequence were proposed based upon the overburden thickness, geology, and the result of the numerical modeling. The second case history documents a nine-entry panel 3,600-feet long that was retreat mined a distance of 2,064-feet without a significant roof fall or roof-floor convergence. Mine management became concerned about the potential for a coal bump or a large roof collapse within the gob and the resulting air blast. The stress on the pillar line and within the remnant pillars in the gob was quantified through numerical modeling. Changes in mining practices on the current panel were implemented to avoid a bump in the active panel. A barrier was established between the current and the future panels to protect the future panel against abutment pressures from the void area. A change in pillar centers was proposed in the adjacent panel to absorb the side abutment pressure from the gob of the active panel.

Jan 1, 2008

By N. Kornelius

In recent years there has been an increased focus on corporate governance matters worldwide. The duties and responsibilities of directors of companies have come under close scrutiny, with shareholders increasing their demands for greater responsibility and accountability. Media attention and pressure groups have also had their effect. Governmental actions have supported these demands and directors have witnessed sweeping legislative changes imposing more onerous duties and liabilities than formerly imposed upon them at common law and in terms of the Companies Act. At the same time, the power of regulatory bodies has been increased to enforce this legislation and make someone pay to remedy an alleged infringement. Breach of such duties may incur personal or criminal liability, or both. Environmental protection legislation has become a particularly prevalent feature in this regard, and the number and complexity of statutes concerning the environment have increased over the past few years. Directors of South African companies will be familiar with relevant acts such as the National Environmental Management Act 107 of 1998; Conservation of Agricultural Resources Act 43 of 1983;Hazardous Substances Act 15 of 1973, as well as the National Water Act 36 of 1998. Now the directors of mining companies are faced with the Mineral and Petroleum Resources Development Act 28 of 2002.

Jan 1, 2003

Barrick Gold plans to have four new gold mines in production by 2006. Together, the mines would increase the company’s output by 40 percent. The projects include Veladero in Argentina, Alto Chicama in Peru, Cowal in Australia and Tulawaka in Tanzania. All of them are scheduled to begin production between the first quarter of 2005 and the first quarter of 2006. They are expected to drive Barrick Gold’s growth profile to a target of 211.5 to 217.7 t (6.8 million to 7 mil-lion oz) of gold production in 2007. The company’s projected output for 2004 is 152.4 to 155.5 t (4.9 million to 5million oz) in 2004. Overall, higher production and lower costs are expected in the early years from the new mines.

Jan 1, 2004

By J. C. Melrose, W. R. Foster, J. G. Savins, E. R. Parish

Many differences can be imagined between gas-oil flow in which the gas is supplied at the face of the core and gas-oil flow in which the flowing gas was originally dissolved in the oil. If capillary pressure characteristics and flow requirements control gas saturation distribution, the gas would be expected to be located at preferred sites within the porous medium as determined by pore sizes. On the other hand, during solution gas drive the gas first appears as bubbles through a nuclea-tion process. Nothing in self-nucleation theory specifies at which sites the first bubbles should be formed. In all probability they will be randomly distributed throughout the porous medium. Furthermore, it is not at all certain that even at low rates of production the gas will redistribute itself after nucleation to the channels normally occupied by gas in simple gas flow. Stewart, et at, have shown that at least for some limestone samples, oil recoveries could not be predicted for all rates of production using any one set of relative gas and oil permeabilities. An important factor in controlling recoveries during solution gas drive was the rate of bubble formation, higher rates giving higher recoveries. Stewart, et al, attributed the increase in recovery to a better distribution of the gas phase in heterogeneous limestone samples than is obtained by simple external gas drive. Differences in recovery from these causes were not reported for sandstone cores. In the experiments to be reported here, oil recovery, pressure and producing GOR history were measured during solution gas drive for a 5-ft sandstone core. The results were compared with predictions from the Muskat method for computing solution gas-drive behavior using external gas-drive relative permeability. The effects of changing the rate of production and oil viscosity were studied. At high laboratory rates of average pressure decline, two observations were made which would not have been predicted by Muskat's depletion theory: (1) oil recovery increased with increasing rate of production for a given viscosity oil, and (2) oil recovery increased with increasing oil viscosity for a given high rate of production. Both of these observations are explained as consequences of diffusion control of gas saturations superimposed on the normal gas-oil flow requirements, Fur- thermore, discontinuous gas phase flow appears to be significant during solution gas drive. The laboratory tests were performed at rates of average pressure decline many times greater than the maximum possible rate of average pressure decline in an actual oil field. It is, therefore, not possible to draw any direct conclusions regarding the effect of rate on recovery for the solution gas-drive mechanism under actual field conditions. However, at the lower laboratory rates, recoveries were nearly independent of rate and could be predicted by the Muskat method, using external gas-drive relative permeability data. These results suggest that at normal oilfield rates the effect of rate on recovery for the solution gas-drive mechanism is negligible. EXPERIMENTAL PROCEDURES The core material for the pressure depletion studies was Bandera sandstone from an outcrop in the Mid-Continent. This sandstone was selected because of its low permeability (about 10 md), which would permit the development of substantial pressure gradients in the corn at moderate flow rates. The core was 5-ft long and 2-in. in diameter. Its properties are listed in Table 1. Relative gas-to-oil permeability ratios were measured by an external gas-drive method2. The results are shown for a short 2-in. core and for the 5-ft core in Fig. 8. Oils used in the pressure depletion experiments were kerosene and a highly refined white oil (standard white oil No. 3) with gas-free viscosities of 1.8 and 25 cp, respectively. The gas was a naturally occurring methane from Gough field, Inglewood, Calif. The oil viscosities, gas solubilities and formation volume factors are plotted as functions of pressure at 75°F in Figs. 1 and 2. Methane viscosities and compressibilities were obtained from the literature"'. A core mounting was required which could withstand up to 2,500 psi internal pressure. This was obtained by first encasing the core completely in a plastic resin (Scotch Cast, manufactured by Minnesota Mining & Manufacturing Co.) The plastic covered core was then inserted into a steel pipe equipped with screw caps so that the plastic coating could be pressured from

By R. Macleod, G. G. Bursey, T. R. C. Aston, J. E. Gale

In 1991 the problems of water inflow at the mine were addressed by a three-phase study. A three-dimensional finite-element computer code, CFEST (Coupled Fluid, Energy and Solute Transport), was used to model the system of groundwater flow around the mine, allowing assessment of the nature of the hydrological regime and of the various recharge mechanisms and sources of inflow. A regional (111 km2) model was used to simulate conditions of low to average mine inflow and provide boundary conditions for the subsequent local (16.8 km2) model. The regional model produced inflows of 0.26 m3/s and the local model 0.25 m3/s. With the use of constant head conditions to simulate a saturated flood plain along the Gays River and on doubling the rate of surface recharge, the local model produced a maximum mine inflow of 0.255 m3/s, in contrast to a measured peak mine inflow of 0.37 m3/s. The discrepancy suggests that during periods of high river level surface water gains access to features with high permeability, such as sinkholes, that may be connected directly or indirectly to the mine workings. Improved simulation of high inflow conditions can probably be achieved by determining the hydraulic conductivity of the river-bed and flood-plain sediments and modelling known sinkholes as discrete units. Possibilities for controlling the amount of inflow to the mine include sealing the flood plain with dykes, checking regularly for new sinkholes, which should be filled and capped, maintaining adequate mine drainage, and monitoring well levels and pressures on a continuous basis.

Jan 12, 1993

By Mark Lawshe, Shosie Serata

The conventional method of mining underground, using narrow rooms and wide pillars, has proven to be poorly adapted to the powerful earth forces that act on underground openings. The high costs of roof bolting, timbering, steel arching, and other means of artificial roof support for both room-and--pillar operations and longwall gate roadways attest to the limitations of traditional mine design. Too often, productivity halts when corners buckle under "cutter roof' stresses, floors heave, and roof strata fall. In the 1960s, an entirely different approach to strata control was developed. The Stress Control Method (SCM) stabilizes failing roofs and heaving floors by removing the cause of failure - highly concentrated stresses around the openings. This is achieved by regrouping three to 10 rooms into a single entry where the rooms are separated by very narrow yielding but stable pillars. SCM employs a specified excavation sequence to redirect earth pressures away from the mine openings. The yield pillars act as scaffolding until a permanently protective secondary stress envelope forms around the entry (lower part of Fig. 1). The result is a dramatic improvement in roof stability and a significant reduction in artificial support costs. Some roof bolting must still be done, mainly to meet Mine Safety and Health Administration (MSHA) requirements. Potash, salt, coal mining The stress control method was first applied to the deep potash mines of Saskatchewan. The new SCM design actually increased room widths to enlarge the stress envelope, redistributing the stress concentration away from the entries (Serata and Schultz, 1972). This resulted in a turnaround from pervasive roof fall/floor heave conditions that threatened operations in the eight new mines opened in the Saskatchewan potash field during the 1960s. In addition to eliminating all roof bolting, SCM successfully stabilized ground conditions and substantially increased productivity over the original design (Serata, 1976, 1982). Similarly, the deep Boulby potash mine of Yorkshire, England, was about to close after various conventional means of combating roof failure had failed. An SCM test area was excavated that resulted in the ground quickly stabilizing without need o artificial support (Serata, 1982; Chilton and Laird, 1982). Another example is the Diamond Crystal salt mine in Louisiana. Here, multiple level mining was being extended from the third to the fourth level downward in the Jefferson Island salt dome. Extensive roof failure was occurring at 396 m (1300 ft) ii the third level. SCM design principles in creased the room size from 24 to 49 m (80 t( 160 ft) on the fourth level at a depth of 457 m (1500 ft). This unprecedented expansion of room width was first questioned and later ap¬proved by MS HA, which expressed satisfaction in seeing the improvement documented by field validation data in 1973. The most recent SUM application to salt mining has been in the Michigan Basin a: Goderich, Ontario. The anticipated abandonment of Domtar Chemicals Group/Sifto Salt Division's deep operation in bedded sale was prevented by a multi-year SCM implementation. The success of SCM in dry mining[lecc] to its application to solution mining of salt This adaptation of the method is now being implemented in bedded salt at Fort Saskatchewan, Alberta by Dow Chemical Co., and in St. Clair, MI by International Salt Co. Application of SCM to solution mining in a salt dome is proceeding at Napoleonville. LA by Dow Chemical. The same technology has also been applied to cavern design for the Louisiana Offshore Oil Port (LOOP), and the compressed air energy storage (CAES)

Jan 1, 1989

By W. W. Scott

The application of engineering methods to the problems connected with drilling and producing in the oil industry has led to the development of the science that is variously termed "petroleum engineering," "production engineering," "petroleum production engineering," and even Itpolitical engineering." It would require much detail to enumerate the qualifications of a petroleum engineer, just as it would for an engineer in any major industry. For those who have a genuine liking for the oil industry, there is a wide selection of pathways to achievement. The oil industry is now highly specialized. Its products are necessary to all civilized people and are indispensable in the security of our nation and also in the well-being of our families. The business structure of our country depends in a large measure upon oil, and the welfare of this group as individuals is certainly linked with the welfare of the oil industry. What Is the Trend of Engineering? The oil industry offers a fertile field of opportunity for engineering; probably more so than any other industry. The sciences of geology, physics, chemistry and mathematics are all used in some phase of the oil industry and to a very considerable extent in the production division, which embraces the geological, drilling and producing departments. In drilling and production alone, research programs of considerable magnitude are being carried on at this time, and no doubt the future will see a great deal more of this kind of work. Through the cooperation of the engineer, the equipment manufacturer, and the American Petroleum Institute, immense savings have been made by the standardization of drilling and production equipment. Drilling equipment in itself offers a wide scope for study, in that continued efforts are being made to improve the equipment so that it can be made to drill faster and to greater depths. The improvements in drilling equipment are required because new reserves of oil are being found at progressively greater depths. In order to produce such oil in competition with oil now being produced from reservoirs

Jan 1, 1937

By Eivind Grøv

"INTRODUCTION Tunneling and underground excavation is related to handling of uncertainties, risks associated with geological conditions are significant and ‘unexpected geological conditions’ often claimed. This fact was brought to the table long ago, and ITA (the International Tunnelling and Underground Space Association) published its 25 Recommendations on Contractual Sharing of Risks in 1988 (Ref. 1). This public-cation constitutes an important asset to the tunneling industry in terms of being a guideline for those working with contractual issues, even today almost 30 years after being published. A more recent document is the ITIG code of practice for risk management of tunnel works from 2015 (Ref. 9). Various countries or geographical regions have their own view and tradition on risk sharing and tunnel contracts. In Scandinavia unit rates contracts are most commonly used with bid-build model, it shares risk between owner and contractor, owner retains the risk for geological conditions while contractor carries risk for performance efficiency. Rock strengthening is determined assessing rock mass quality encountered at tunnel face. Grouting is applied to stem water. Actual quantities may differ from the contract’s BoQ but a flexible contract with remuneration is installed to enable adjustment of actual quantities. Variations of quantities involve a clause to adjust construction time. Unit price contracts deals with expected and foreseen still ‘unexpected geological conditions’, if the ‘unexpected’ element results in variations in quantities. Work activities have quantities and ‘standard capacities’ for regulation of construction time. Variations in quantities are expected in tunnelling and hardly deserve the term ‘unexpected’. If truly unforeseen geological features necessitate work not included in the BoQ, then the contract must be supplemented and can be said to be inappropriate. Fixed price contracts may not provide the intended predictable cost and is as such also inappropriate in the view of a risk sharing principle, once the geological baseline proves to be incorrect. ‘Adjustable fixed price’ contracts, combining unit rate and fixed price, may prove suitable."

Jan 1, 2016

By A. Gupta, S. C. Srivastava, K. K. Saroj

Bacterial degasification of methane and conventional methane drainage for generation of power have become accepted practice. Comparative economies of both the techniques have been described. Authors have discussed an alternative technique, involving complete methane biocycle. The first stage of the entire process involves gasification of coal using a consortia of bacteria to generate methane. The generated methane has been proposed to be pumped,as in conventional methane drainage. Technique described is basically similar to underground coal gasification, with the difference that in place of coal combustion, degradation of coal to lower molecular weight compounds by one set of bacteria and then methanogenesis by methanogens, producing methane have been described. Brief account of communities of bacteria that may be employed have been dealt with. Three arguments in favour of proposed technology as an alternative to conventional coal mining are: 1.Total elimination of hazardous operation. 2.Availability of power plants based on methane drainage, assuring comparative economies. 3.Possibility of utilisation of fuel cell technology for power generation giving higher efficiency. All the three phases of complete blocycle viz (1) methane generation from coal (ii) conversion of methane to hydrogen and oxygen (iii) conversion of products so obtained to methane, thereby completing the cycle have been discussed. INTRODUCTION Drainage of methane by conventional pumping process (Boxho,et.al.,1980) not only is helpful in maintaining safe extraction of coal, but with utilisation of extracted gas for power generation, also helps in over all economy of coal mining. This is gradually becoming standard practice for mining of coal in highly gassy mines. An alternative technique (Thakur et. al., 1991) of bacterial degasification of coal seams is also gradually gaining ground. The bye products of this process that is carbondioxide and water, do not contribute towards economy of coal extraction process. However the technique has its own advantage particularly in goaf area for avoiding fire hazard and drainage of methane from coal seams prior to initiation of mining operation. Either of these techniques could be applied in specific situations with success.

Jan 1, 1993

By George A. Roberts, Arthur H. Grobe

Tensile, hardness and density properties are presented for a new 18-8 stainless steel powder for the —50, —100, and —140 mesh cuts and also for a prepared blend containing 62 pct —325 mesh powder. The data were obtained for sintering temperatures of 2100° to 2350°F and for compacting pressures of 30 to 50 tons per sq in. A NEED has existed for a stainless steel powder of uniform composition from particle to particle, which could be readily molded and sintered, and which would yield moderate to high strength and ductility when processed into parts by standard powder metallurgy techniques. The literature reveals that previously available powders have been lacking in one or several of these desirable characteristics. Originally attempts to produce stainless steel powder by blending and diffusing elemental metal powders were unsuccessfu1.l A truly alloyed stainless steel powder reported by Dale in 1947 yielded reasonable mechanical properties but required an exceptionally high sintering temperature of 2400°F in pure dry hydrogen.' A later development reported in 1950 by Stern provided a stainless type powder of excellent molding properties' but this powder likewise required sintering at temperatures over 2350 °F and did not yield properties as high as those previously reported. The powder was not truly alloyed prior to sintering. A prealloyed stainless steel powder has been developed that is readily moldable at 30 to 50 tons per sq in., can be sintered at low temperatures (2100" to 2300°F), and which yields compacts with both high strength and ductility. The powder is prepared by the liquid disintegration method," direct from molten metal. Early attempts to make 18 pct Cr, 8 pct Ni stainless steel powder by this method did not produce a usable powder for pressing and sintering because of a preponderance of spherical particles with relatively high, surface oxide content. It was learned that silicon additions to iron alloys, powdered by this process, gave bright powder of low-oxide content and such additions were made to 18-8 stainless with similar results. An attendant change in particle shape occurred reducing the number of spheroids materially. The optimum composition which has been studied and is reported here contains approximately 2.5 pct Si. Silicon additions to stainless steel of the 18-8 type improve the resistance to high-temperature oxidation and promote the formation of ferrite. Corrosion resistance is, however, controlled by chromium content and even though ferrite may exist the corrosion resistance is not generally impaired.4 Experimental Procedure A detailed study of the 18-8, 2.5 pct Si powder has been made in accordance with the following outline: 1. Four blends a. — 50 mesh b. —100 mesh

Jan 1, 1952

By S. S. Clarke

THE sheet-ground deposits of the TriState district, because they are fairly uniform in thickness (7 to 11 ft.)-rather flat, with an easy dip to the west-and cover a large acreage, offered a problem of improved transportation. Heading advance in this kind of mine is very rapid and track haulage requires a larger crew of trackmen than do other mines, and a heavy investment in track. The use of some type of rubber-tired truck equipment for underground haulage was under consideration for some time by the Eagle-Picher Mining and Smelting Co. The nature of some ore bodies made them not adaptable to truck haulage and some mines that did offer possibilities were equipped with other types of haulage, and the expected savings by the use of trucks did not offset the loss of investment that would be incurred in discarding other equipment. The decision was made to sink a new shaft, designed for skip hoisting, on the Blue Goose ore body, and then develop truck equipment. DEVELOPING TRACTORS AND TRAILERS A study was made of internal-combustion engines for power units in the tractors, but the extreme difficulty of controlling air circulation, and the heavy cost of drilling large churn drill holes for blower installations, led to the adoption of a tractor with a storage battery. The storage-battery tractor that was on the market for mine haulage was impossible to obtain because all were needed for defense work. Several standard electric-truck chassis were purchased and rebuilt in the Eagle-Picher shops. The steering wheel was shortened and set vertical, permitting the driver's seat to be moved forward, and the frame was shortened enough to take the battery box and the fifth wheel support that carried the gooseneck of the dump trailer. The fifth wheel, or turntable, is of the ball and socket type. Fig. I shows the ball fastened to the gooseneck. The socket is split to permit introduction of the ball and is held by through-bolts, and the socket is welded to a ½ -in. plate, which in turn is attached to the tractor frame. Smaller wheels and tires were put on to reduce over-all height. If it had been necessary, the springs could have been reversed, or taken off entirely, to gain additional clearance. The tractors are equipped with 48-cell, 23-plate, 400-A.H. batteries. With the initial tonnage and mileage, the batteries were about 50 per cent down at the end of a shift. Tractors have truck tires 7.50 by 20, 8-ply, front and rear, the rear being dual. After four months of use, the tires are beginning to show signs of failure.* In

Jan 1, 1942

By D. A. Cormode

"INTRODUCTIONPine Point Mines, operated by Cominco Ltd., is located approximately 55 miles east of Hay River, N.W.T. by the southern shore of Great Slave Lake.The milling operation commenced in the fall of 1965 at a design capacity of 5,000 tpd. An addition which came on stream late in 1968 raised the nominal capacity to 8,000 tpd. Currently the milling rate is 11,000 tpd.The lead and zinc sulphides occur in dolomite host rock. Typical feed grades at present are 2% lead, 5.5% zinc and 5 % iron. When dolomite is present even in relatively minor amounts in the zinc concentrate, it presents serious treatment problems and causes inefficient operation of electrolytic zinc refineries.By 1972, it had become apparent that magnesium rejection in the form of dolomite was deteriorating because of increased plant throughput of less amenable ore. This paper will briefly outline the Pine Point zinc flotation circuit and will discuss the two phase program for reducing the magnesium level in the zinc concentrate. The program included changes and alterations to the flotation circuit and the construction of an acid leaching plant."

Jan 1, 1977

By Rossano Augusto Pilon Nunes

A pelotização é um dos processos desenvolvidos para permitir utilização dos finos (pellet feed) nos reatores de redução. O produto gerado denominado ‘pelota’ possui alto valor agregado e características físicas e metalúrgicas próprias. Dentro das características físicas temos as trincas que são defeitos internos e/ou superficiais que prejudicam o desempenho das pelotas nesses reatores. O estudo visou investigar as variáveis que mais contribuem para geração das trincas e em que etapa do processo a geração é mais significativa. A investigação avaliou duas usinas de pelotização de Tubarão, na geração de trincas e comparou as principais variáveis de processo segundo a literatura. Esta avaliação se deu em escala piloto utilizando um forno tipo pot-grate e mostrou forte influência das etapas de secagem descendente e pré-queima. O trabalho foi de suma importância para uma atuação mais direcionada em um futuro teste industrial.

Oct 30, 2017

By Lina Maria Varón Cardona

A utilização de briquetes de misturas de carvão fóssil e biomassa em substituição ao coque como agente redutor pode contribuir para a diminuição das emissões de CO2 à atmosfera no processo de fabricação de ferro através da substituição de parte do carvão fóssil por carvão vegetal. O objetivo deste artigo é identificar quais são as principais variáveis que influenciam a produção de briquetes de alta qualidade a partir de misturas de carvão fóssil e carvão vegetal. Os briquetes foram fabricados em matriz cilíndrica, compactados em prensa hidráulica e tratados termicamente em forno vertical aquecido com resistência elétrica sob atmosfera de nitrogênio. Foi investigada a influência da composição da mistura, da taxa de aquecimento e do tamanho de partícula do carvão fóssil. Os briquetes com composição na faixa de 10% a 15% de carvão vegetal moído e peneirado em partículas menores que 325 mesh apresentaram maior resistência à compressão. Foi observado que o efeito do envelhecimento do carvão influencia na qualidade do briquete, pois diminui sua resistência à compressão; as dimensões finais dos briquetes após tratamento térmico diminuíram quando a velocidade de aquecimento é menor; ao se aplicar maior velocidade de aquecimento os briquetes apresentam inchamento.

Aug 1, 2018

By Mariana Peixoto

Muitos componentes de ferro fundido ficam expostos a altas temperaturas quando em serviço, podendo ocorrer a decomposição da perlita através da difusão do carbono da cementita para as lamelas de grafita, resultando em alteração microestrutural e degradação das propriedades mecânicas. A influência que a temperatura e o tempo de exposição têm sobre a microestrutura de um ferro fundido cinzento foi avaliado em amostras de quatro ferros fundidos de mesma base, com diferentes percentuais de cromo e molibdênio. Ensaios de banho de sal a uma temperatura de 500ºC foram realizados em corpos de prova com diâmetro de 10 mm. Os ensaios foram realizados com tempos de exposição a esta temperatura, após homogeneização térmica do material, de 0, 1, 2 e 4 horas. As análises metalográficas evidenciam a ocorrência da decomposição da perlita. Adicionalmente foram realizados ensaios de microdureza, a qual se mostrou sensível às alterações microestruturais geradas pela temperatura elevada. O ferro fundido com maior percentual de cromo e molibdênio apresentou melhor estabilidade da microestrutura para as condições ensaiadas.

Aug 17, 2017

The Tasman Orogenic Zone is regarded as a single metallogenic province (the Tasman Province) with four SUb-provinces corresponding with its major tectonic components: the Lachlan, New England, Hodgkinson.and North Queensland orogenic provinces. Within the Tasman Province there are four main ore-rock associations.These are1. manganese and iron with sedimentary and basic volcanic rocks,2. zinc-lead-copper and copper with intermediate-acid volcanic sequences,3. minor chromium, platinum, and osmiridium with ultramafic complexes, and4. tin, wolfram, gold, and copper with syn- and posttectonic granitic intrusions.Whereas the ores of ultramafic and volcanic associations form geographically-restricted metallogenic districts, the ubiquitous granitic ores may be subdivided into twenty-one districts that cover almost the entireOrogenic Zone. The Tasman Province is notably lacking in uranium ores and Mississippi Valley-type deposits.There is a distinct tendency for ores of each association to be progressively younger to the east and north, thus paralleling the progressive growth and stabilization of the Zone. Similar ore-rock associations are present in repeated phases of mineralization from the Cambrian to the Permian-Triassic, reflecting the essential homogeneity of the Tasman Province, and the similarity of the successive tectonic cycles.

Jan 1, 1972

In This Chapter [Finding the dust source Ventilation and dust collector malfunctions Upgrading the dust controls Design stage ventilation planning ] This chapter explains how to reduce respirable dust76 in hard-rock tunnels during excavation by using tunnel boring machines (TBMs). The first steps in combating a dust problem are to take dust samples to pinpoint the source, check the ventilation system, and check the dust collector. If the ventilation system and dust collector are operating properly, then other dust controls such as water sprays and conveyor belt scrapers must be upgraded. For tunnels in the design stage, recommended air quantities are provided. FINDING THE DUST SOURCE AND LOOKING FOR VENTILATION MALFUNCTIONS [The first steps in fighting a dust problem are to take dust samples to pinpoint the source, check the ventilation system, and check the dust collector. Without knowing the exact source, efforts to reduce dust are hit-and-miss (mostly miss).] Taking samples to pinpoint the dust source. In tunnels with high levels of airborne dust, the first task is to pinpoint where the dust enters the airstream. Most dust originates from rock breakage at the tunnel face, but the location where this dust enters the airstream can vary. Dust can leak from behind the TBM face shield, from gaps in the ventilation duct, or from a mal-functioning dust collector. It can be entrained into the air from the muck on a moving conveyor belt. It can even be shaken loose from the underside of the belt as it passes over the idlers. As a start, to locate the dust source, dust samples and air quantity measurements should be taken at the following locations:

Jan 6, 2003

The National Institute for Occupational Safety and Health (NIOSH) has continued study of the Personal Dust Monitor (PDM) developed by Rupprecht & Patashnick Co. Inc. through a CDC contract and currently being commercialized by Thermo Fisher Scientific. This report examines the effect of oversize particles, cyclone inversion, and cleaning procedures. Clean and exposed filters were examined using light microscopy and particulates counted before and after various instrument manipulations. The data presented show that the dry cleaning procedures do not cause significant (greater than limit of detection) sample contamination by respirable or oversize particulates and that the cyclone is resistant to particulate carry over during inversion.

Jan 1, 2009

By S. G. Enns, E. W. Yarrow

"Situated about 200 km southeast of Juneau, Alaska, within the lower Stikine River region of northwestern British Columbia, the Galore Creek porphyry Cu-Au deposits are hosted by Upper Triassic to Lower Jurassic alkaline volcanic rocks and comagmatic syenite intrusions. Early and late breccias are also locally important host rocks for mineralization. Of the twelve identified Cu-Au deposits, the most important are the Central zone, Southwest zone and the Junction deposits with a combined resource of 284 million tonnes at 0.67 % Cu.The composition of the intrusive rocks is predominantly silica-undersaturated, alkaline, and metaluminous. Four intrusive suites are identified from field, petrographic and petrochemical data. Variation within suites or lineages can be explained by alkali feldspar fractionation. An oscillation between porphyritic and equigranular intrusions is suggested by the sequence of different intrusive lineages. The youngest intrusive phase is silica-saturated.A complex succession of intrusive and hydrothermal events is demonstrated at Galore Creek, with the most intense alteration and mineralization developing early in its history. In the Central zone, early Ca-K-silicate alteration, dominated by garnet, biotite, Kfeldspar, and anhydrite grades outward into K-silicate alteration. Both are locally overprinted by retrograde sericite± anhydrite± carbonate (SAC) alteration. The most intense Ca-K-si/icate alteration, a magmatic-hydrothermal breccia, and an early syenite intrusion are all coincident with copper mineralization in the core region of the Central zone. However, higher grade mineralization in the zone, exceeding 1 % Cu with more than 0.5 g/ t Au, is typically associated with intense biotite-rich, K-silicate alteration primarily hosted by altered volcanic rocks. The highest gold grades, commonly exceeding 1 g/t, are associated with bornite-rich mineralization situated in the northern and southern parts of the Central zone.Mineralization in the Southwest zone occurs as disseminated chalcopyrite within a late, diatreme breccia and adjacent K-feldspar porphyry. In the other satellite deposits, disseminated chalcopyrite and bornite occur in volcanic rocks with alteration that is similar to the Central zone."

Jan 1, 1995

By Phil N

A large number of experiments have been carried out by many workers on the recrystallization of deformed and subsequently annealed metals and alloys. Although observations on single crystals are of great importance in the study of the recrystallization textures of deformed and annealed metals, very little of this work deals with material in this form.Since, in deformed metals, the stress concentration is greatest at the grain boundaries and along the planes of slipping, it is to be expected that recrystallization will start in these regions. For example, in polycrystalline aluminium (1),:1: (2), copper (3), a-iron (4) and brass (5), (6), which had been deformed by cold-rolling, drawing, pressing or stretching and then annealed, the new grains first appeared in the boundaries of the original crystals, whilst in the case of cupronickel (7) and iron (8), recrystallization commenced along the slip planes of the deformed material. Deformed and annealed single crystals of aluminium (9) and cadmium (10) first start to recrystallize along slip planes and in deformation twins.The present work deals with the process of recrystallization of single crystals of lead after deformatjon by creep.Two factors enter into these experiments that were not met with in other work on this subject. Firstly, lead...

Jan 1, 1940