Search Documents

Early in 1940 the development and sampling programmes in hand on the North and British Sections of North Broken Hill Limited were such as to necessitate the drilling of a large number of drill holes ranging up to about thirty feet in length. On the British Section, one purpose was to test the existence, width, and value of narrow lodes believed, for geological reasons, to occur in the walls of the existing workings. Another object was to definitely disprove the existence of payable shoots of ore in certain largerhodonite and quartz-garnet ("garnet sandstone") pillars which had been formerly left as unpayable.On the North Section, the main purpose of the short holes was to delineate the ore-body boundaries by drilling laterally from drives in ore, and thus enable level layout to be planned in advance of sill stoping. It was also desired to test the walls of stopes in those portions of the mine where the economic limit of mining is not rendered obvious by a clear-cut wall, but should be determined by assay. In these latter cases it was hoped to eliminate "prospecting by stoping," a procedure by which any doubts as to the existence of further good ore behind the low-grade walls were settled by continuing to stope laterally until all chance of such an occurrence was removed.LONG HOLE ROCK DRILLINGFollowing an investigation of recorded instances of similar practice elsewhere it was decided to use the rock drill for a series of trial sample holes. A 3-in. drifter was used. This was selected from those in use underground, and was given a special overhaul; had a new machine been purchased, a 4-in. type would probably have been obtained as being more suited to the work. The rods were H in. hollow round steel with a type "1" Jackrod thread. Couplings were of chrome steel, and were H in. in diameter, and 2 in. long. Jackbits (type "1" thread) in sizes from 2 in. to 4 in., with 1-in. gauge changes, gave a range of nine bit sizes. They were resharpened by hot milling, and were not milled to a definite gauge size.After sharpening, bits were sent underground without sorting into sizes, the drillers selecting the next bit with callipers. In view of the small scale of operations, it was not considered worth while to adopt special measures, such as the cold grinding of bits, which might have given a better product. Later, however, new bits were used exclusively, the idea being to accumulate enough blunt Jackbits to warrant a thorough treatment of the sharpening...

Jan 1, 1941

By Tom Gonzales

At San Manuel, AZ, Magma Metals Co. operates an Outokumpu flash furnace, four Peirce-Smith converters and two anode casting wheels that are supported by six anode vessels. Process gasses from the flash furnace and converters are treated in a two-train/ double-contact sulfuric acid plant. The plant captures 98% of the sulfur. A new flash furnace was commissioned in July 1988. It has since processed more than 2.7 Mt (3 million st) of sulfide concentrate without a major rebuild. The company has gained unique experience in the operation of the flash furnace at high oxygen enrichments with low off-gas dust loadings. New procedures have been developed to maintain secondary material generation at equilibrium and for maintaining metallurgical control of operating parameters. Process flow description At Magma's San Manuel plant, concentrates and other copper-bearing material are blended and conveyed from two separate areas of the plant to three 420 t (465 st) capacity wet charge bins located above the rotary dryer. Flash furnace silica flux is conveyed to a 227-t (250-st) capacity fine flux bin located adjacent to the wet charge bins. The concentrate and flux are blended in controlled amounts and fed into a 168-t/ h (185-stph) gas-fired rotary dryer. The wet charge enters the dryer at 8% moisture and is dried to 0.2% moisture. The dried charge is pneumatically conveyed to a 580-t/h (640-stph) dry charge bin located above the flash furnace. Flash furnace charge is drawn from the bin by two drag conveyors at a concentrate feed rate of 145 t/h (160 stph). The charge is mixed with enriched combustion air and injected into the furnace reaction shaft. In the reaction shaft, the charge is oxidized to form matte, slag and a rich SO, off-gas.

Jan 1, 1992

By W. C. Meyer

Surface tension and its control are important in the concentration of ores by froth flotation, both in terms of producing the proper bubble size distribution and to render the ore surface of interest hydrophobic such that adhesion to a bubble will take place. The influence a substance has on surface tension has traditionally been measured using static, equilibrium techniques. Yet many applications such as flotation involve rate-related effects of surface tension where equilibrium values are not reached. In the time frame of 1 - 300 seconds, aging effects have been noted for bubbles formed in dodecylamine acetate solutions; a slow decrease in surface tension occurs until an equilibrium value is reached, as studied by Finch and Smith (1972). Since stationary bubbles do not exist in flotation cells because of the turbulence generated by agitation and aeration, it is more likely that the chemical composition of the bubble is determined during its formation, under dynamic conditions. The chemical composition is extremely important because the induction time required for a particle-bubble entity to collide and adhere to each other is augmented by favorable surface tension (wetting) proper- ties between the surface of the particle and the bubble air-water interface or envelope, as considered by Mackenzie and Matheson (1963). Finch and Lyman (1976) have established that the probability of a "permanent" attachment taking place during this contact time is aided by the ability of an oil droplet (viz. bubble) to relieve non- equilibrium surface tension effects which are involved in the water-thinning process. This Maragoni effect, or surface elasticity, can be considered in the context of particle agglomeration addressed by Kao and coworkers (1975). Water drainage leads to the formation of a collector-frother meniscus appearing between the colliding entities, arising from their combined partial immiscibility in the water phase and promoted by hydrophobic bonding within the interface. Together they constitute a liquid bridge whose force of attraction drawing the particles together is proportional to the interfacial tension existing between the water phase and liquid bridge. This adhesive force shows an approximate linear decrease with separation distance until rupture occurs, that is, FX = Fmax (1 ? X/Xr) (1) for a distance of separation X and rupture distance G. The greater the surface elasticity of the bubble, the greater will be the rupture distance and the better will be the force of adhesion. Since van den Tempel (1965) has related surface dilational properties of bubbles to the elasticity, E, of the film as

Jan 1, 1983

By J Hall, A Gallardo, M Strizek

Mineralogy and coproponents Sino Iron, International Minerals and Austeel are in the process of developing four world class magnetite iron ore mines with multiple open pits along a 25 km strike length of Brockman Iron Formation to the south of Cape Preston on the West Pilbara coast. The close proximity of the proposed pits raises some challenging project approvals and environmental management issues relating to the impacts of dewatering at individual projects and the cumulative impacts of progressive development on local and regional groundwater resources, which includes a large fresh water aquifer system in the Fortescue River alluvium.This paper presents an outline of the hydro-environmental impact assessment process adopted and the key result that the cumulative impacts of dewatering at all four projects on the local brackish groundwater system in the basement rocks is only marginally more than the impact of any one project on its own, and that the impact on the Fortescue River alluvium aquifer is negligible. The paper also presents an outline of the proposed integrated water management approach that will involve coordinated monitoring, ongoing impact assessment and management, and reporting programs for all projects.

Jan 1, 2009

By Carole L. B. Mitchell

The South 180th Street Grade Separation underpass in Tukwila and Renton, Washington, USA, permits vehicular traffic to pass beneath Burlington Northern Santa Fe and Union Pacific railroad tracks. The railroad tracks were temporarily relocated onto a shoofly crossing while the permanent bridges were constructed. The maximum underpass depth is approximately 25 feet (7.6 meters [m]). The majority of the sidewalls are supported using alternating reinforced and unreinforced secant pile walls. Temporary and permanent struts brace the top of the excavation. Because the groundwater is about 15 feet (4.6 m) above the base of the excavation and the subsurface materials are loose to medium dense fill, alluvium, and soft flood plain organics, the base of the excavation was strengthened and sealed using wet cement deep soil mixing (CDSM) methods. During construction, CDSM-treated ground temporarily acted as part of the railroad shoofly shoring while the remainder of the underpass was excavated on either side of active railroad tracks. The combination of secant pile sidewalls and CDSM bottom seal allowed for easy excavation, even during wet conditions. Using a 35-foot-thick (maximum) (10.7-m) CDSM layer both to act as a bottom seal and to resist uplift pressures is a unique, dual-purpose application of CDSM technology in the United States.

Jan 1, 2004

By George K. Burke

Single axis soil mixing is a mechanical method of blending soil in situ with a reagent binder to achieve improved character. Generally this achieves a design compressive strength or shear strength and/or permeability, but can be used to immobilize and/or fixate contaminants as well as a treatment system for chemical reduction to a more "friendly" substrate. The reagent binder can be a variety of materials, including cement, fly ash, slag, lime, and an assortment of additives. Usually this reagent is delivered in a slurry form (combined with water), but the Dry Mix Method uses pneumatic conveyance.

Jan 1, 2001

It has been thought in the past that New Zealand had ample coal reserves, able to provide fossil fuel supplies well into the future. Such is not the case and every effort must be made to achieve the highest possible extraction rate in all new coal mining ventures. While the relative cost and availability of completion or fuels has been largely responsible for the slow growth of coal production in the past, a world shortage of fuels has given coal a new importance and required better utilisation of coal reserves. New mining ventures in thick-seam coal deposits cannot be planned and designed without geotechnical investigations designed to provide information required by the mining engineer and analyst. Finite element analysis of mine workings may provide essential information on the optimisation of mining techniques and the design of underground support and roadway shapes.

Jan 1, 1976

By L Singheiser, W. Willenborg, M. Mueller, K. Hilpert

The limitation of fossil fuel resources and the necessity of reducing CO2emission require an increase of the efficiency of power plants by using combined cycle power systems. Pressurized Pulverized Coal Combustion (PPCC) is a potential concept to realise these objectives. The direct use of hot flue gas for driving a gas turbine requires a hot gas cleanup to achieve corrosion prevention of the turbine blading. One of the main problems is the alkali release during the coal combustion process. Molten coal ash slag has a high potential for alkali retention which depend son the alkali oxide activity in the slag. Knudsen Effusion Mass Spectrometry (KEMS) was used to determine thermodynamic data of alkali gas species over molten coal ash slags and of alkali oxides in molten coal ash slags. The main interest of the investigations focused on the structural dependence of the thermodynamic properties of the alkalis. It was found that there is a strong correlation between the thermodynamic properties and the ratio of nonbridging oxygen to tetrahedral oxygen (NBO/T). An increase of the polymerization of the slag results in a decrease of the alkali oxide activity in the slag and thus a decrease of the alkali partial pressure over the slag. Keywords: coal ash slag, structure, alkali oxide activity, alkali vapour pressure, PPCC, KEMS.

Jan 1, 2004

Previous published papers by Fraser (1), Hey (2), and Stillwell (3), have given respectively, details of:-1. The practice in the pilot plant operated at Zeehan for the treatment of ores from the Rosebery field.2. The design, based largely on the experience gained at Zeehan, of the concentrator built at Rosebery.3. The nature of the orebodies of the zinc-lead lode at Rosebery.Changes and developments, at the Rosebery concentrator, since operations commenced, are now described with particular reference to recent practice.Three concentrates are produced, viz.: a copper, a lead, and a zinc concentrate. The current flow-sheet is shown in Fig. 1. Typical concentrate assays are...THE OREThe ore treated is derived from the Rosebery and Hercules Mines and is, milled in the ratio of, approximately, two parts of the former to one of the latter. The ores from the two mines may be considered as being similar in general character, although the Rosebery ore contains more pyrite. It is from this mine that any increased tonnage is expected. The ore is a mass of fine-grained, intimately associated sulphides, with practically no coarse...

Jan 1, 1949

"Prior to the publication of the General Report of the Miners' Phthisis Prevention Committee of South Africa in 1916 little attention was paid to the dust hazard and the necessity for its suppression in the underground workings of the Broken Hill mines. Such precautions as were observed for the elimination of dust were related rather to the prevention of lead poisoning, which, in the early days of Broken Hill when large tonnages of lead carbonate ore were being won, was rather prevalent. Ventilation and hygiene followed the general practice in this and most foreign countries.This paper covers incidence and action since 1918, considering medical aspects and operating aspects. "

Jan 1, 1947

By Enver Alan, MerkeziYapı

People are migrating because of economic, social, natural and political reasons. These natural and humane factors effects the distribution of populations. The need for tunnels has grown in order to provide a comfortable life and reduce losses such as waste of time, labor, energy, efficiency and so on. It is inevitable to carry out excavations in rock tunnels (shears, platforms, lines, connections, wastewater, distribution, energy, transportation etc.), that will be built by excavating with conventional method, by controlled blasting regarding with constrains. In this study of applied explosives engineering the blasting applications are evaluated, which were carried out for research and development purposes at Yenisahra Station tunnels in Kartal Formation which was built with the aim of solving İstanbul's transportation problem within the framework of the Kadıköy-Kartal Metro Project. Twenty-four shots were made by using explosives in 60 blastholes that were drilled in the tunnel faces, which were located between and outside of two different faults. Six microphones were used to measure the air shock and eight geophones were used to measure the parameter values of the vibrations (particle velocity, frequency, displacement, acceleration, amplitude, wavelength etc.), which were placed at predetermined points of the surface, occurred during the blasting applications. Data from the geophone and microphones were recorded on six seismographs. The coordinates and the distances between the shot points and the measurement stations are determined by an electronic theodolite. The total number of seismic records, recorded in seismographs, is 118. The number of records of vibrations that crossed the faults is 42 and the number of records of vibrations that did not cross the fault is 76. The particle velocity, frequency, amplitude, acceleration, displacement and wavelength were measured in transverse, longitudinal and vertical directions. The total number of measurements is 354. By evaluating all seismic records, the effect of delay intervals, faults and scaled distances on the particle velocity, frequency, amplitude, displacement, acceleration, wavelength and air shock were investigated. When the vibrations formed during the Research & Development (R&D) blasts were examined, it was determined that the parameter values of vibrations that crossed the faults are lower than the ones that did not cross the faults. In addition, when the particle velocity values of all vibrations are examined according to the present circumstances, it is determined that the waves did not cross the fault in all delay intervals are superposed in all directions, and that the least superposing occurred in the 50 ms delay range.

Dr R. E. Robinson, Pr. Eng., obtained a B.sc. (Chem. Eng.) cum laude from the University of the Witwatersrand in 1950 and a Ph.D. (Eng.) from the same University in 1953, where he was awarded the Haikes Memorial Medal for Industrial Chemistry. Professor G. G. Garrett was appointed Professor of Physical and :Fabrication Metallurgy in the Department of Metallurgy at the University of the Witwatersrand in June 1980, and in January 1984 he became Head of the Department. Mr P. A. van Wielligh, Pr. Eng., climbed the mining ladder in the hard way, starting as a Mine Surveyor in 1936 and working his way up as Chief Surveyor, Underground Manager, Mine Manager, and Consulting Engineer, to Executive Director, including the intermediate steps. Mr H. E. James, Pr. Eng., is a graduate in Chemical Engineering from the University of the Witwatersrand. Both his B.sc. degree (1961) and his M.sc. degree (1964) were obtained on bursaries, the former from Gold Fields of South Africa and the latter from the Atomic Energy Board. Mr G. Pienaar, Pr. Eng., obtained a B.Eng. (Met) in 1967 and an M.Eng. in 1973, both from the University of Pretoria. Dr A. K. Haines, Pr. Eng., obtained all his degrees from the University of Natal, finishing with a. Ph.D. in 1971. Mr B. C. Alberts, Pr. Eng., obtained his academic training at the University of Pretoria, where he was awarded B.sc. degrees in both agricultural engineering (1963) and mining engineering (1965). Mr H. C. van Zyl, Pr. Eng., holds B.sc. degrees in mining engineering (1968) and civil engineering (1972), both from the University of Pretoria.

Jan 1, 1984

By H. Fayed

Two-phase (water and air) flow in a self aerated WEMCO flotation machine has been investigated using computational fluid dynamics (CFD). A 0.8 m3 model is considered. The flow is modeled by Euler-Euler approach, and transport equations are solved using a commercial software ANSYS-CFX5 [1]. Because of the lack of circumferential periodicity in this machine, the entire machine is modeled and unsteady simulations are conducted in the whole volume of the bulb. Uniform bubble diameter is specified, and the effects of bubble diameter are determined by conducting simulations for three diameters of 0.5, 0.7, and 1.0 mm. The unsteady air flow rate through the machine is predicted as an outcome of the simulations. Air volume fraction contours and velocity field in different parts of the machine are presented and discussed.

Jan 1, 2012

By S. Nakajima, H. Okazaki

Quantitatiue studies of the deformation texture in drawn tungsten wives were made by the X-vay dif-fractottletetr. Experimental results show that the diffraction Intensities are equal to tilose pvedicted from the (1 10). fiber lexlure but the angxla), spreads of. diffraction peaks in the pole distribution curres are different for different diffraction planes and directions. For this reason a modified (110) fiber lextuve model, in which a kind of anisotropy is assumed, is proposed to explain the results. According to this model the poles lying on a line directing front the (110) to the (110) poles in the (1 10) standard stereograpllic projection should show spreads which are different from those lyitlg on a line directing from the (001) to the (001) poles, which is confirmed by the experiments. The anisolvopy and the spveads of the pole positions are large at the outer part of the wires and decrease gradually lowards the inside of the wire. The possibilily of occurrence of such anisolropy in irrelals with fcc stvuctures is discltssed. THE deformation texture of drawn tungsten wires has been assumed by different investigators to be the simple ( 110) fiber texture.' Recently, however, Leber2,3 has shown that a swaged tungsten rod has a cylindrical texture. It changes gradually to the (110) fiber texture by drawing through dies. However, even after drawing to 0.25 mm in diam, the cylindrical texture can still be found in wires together with the (110) fiber texture. This was deduced from the pole figures obtained from the longitudinal section of these wires. Use was made also of quantitative measurements of the pole distribution curves. Leber stated that the angular spread of the pole distribution curves (henceforward called dispersions) are quite different for (400) 45 deg and (400) 90 deg: the former is always larger than the latter. This inequality is accompanied by deviations of the diffraction intensities from the theoretical values for the ( 110) fiber texture. Bhandary and cullity4 have reported similar results on iron wire and explained them by assuming a cylindrical texture. Both Leber3 and Bhandary4 used only the results of the (400) reflection for the determination of the dispersion. The pole figures found by Leber3 and by Rieck5 are largely different. The model given by Leber to explain the effects is in the authors' opinion in some respects unsatisfactory, especially if one looks at other than the (400) reflections. Intensities and dispersions of diffraction peaks are conclusive factors for the determination of the fine structure in wire textures. For this reason we studied them extensively to come to a model which is more suitable to fit the facts. In the following, after giving the experimental set-up, we report about measurements of X-ray diffraction on drawn tungsten wires. Different models to describe the experimental results will be discussed. EXPERIMENTAL GO-SiO2-A12O3 doped tungsten wires drawn to 0.18 mm in diam were used for the measurements. The wires were chemically etched to various diameters down to 0.03 mm. Measurements were carried out for the different wires in order to determine the dependence of the texture on the radius. The wires were cut to pieces of 10 mm length and fixed with paste closely against each other on a flat, polished glass plate. Parallelism of the wires with the surface of the glass plate should be adequate. For the diffraction studies three different X-ray sources were applied, respectively, giving the CuK,, FeK,, and FeKp emission. The measurements were carried out with a diffrac-tometer with a GM counter. The latter was fixed to a certain diffraction angle 20hkl and the diffraction intensity was recorded as a function of the angle of rotation of the specimen around the axis, lying in the specimen surface and perpendicular to the wire axis, as shown in Fig. 1. Measurements were also done with the detector at angles slightly deviating from the diffraction maxima The measured intensities in this case were taken to be equal to the background level. The deviations were chosen as small as possible but large enough to eliminate the influence of the diffraction maxima. The useful range of the rotation angle x of the specimen is generally limited by the wavelength of the X-rays. We have: where and cp is the angle between the wire axis and the normal of the diffraction plane. Intensity measurements were made to find the necessary corrections for counting loss of the GM counter and for distortion resulting from such effects as absorption of X-rays and from inclination of the reflection plane under study with respect to the surface of the specimen. The counting loss was esti-

Jan 1, 1968

Kinetic Study on the Leaching of Vanadium from LD Converter Slag Using Sulfuric Acid In order to reduce the environmental impact due to land disposal of LD (Linz-Donawitz) converter slag from steelmaking plant and to valorise this waste material, an acid leaching study was carried out to assess the effect of several parameters on the kinetics of vanadium dissolution. The characterisation and morphology of the feed investigated using XRD, XRF. The factors influencing leaching vanadium such as particle size, temperature, slurry density and the concentration of sulfuric acid were investigated and optimised. The maximum vanadium recovery about 95 per cent achieved at 70¦C, S/L: 1/15, acid concentration: 3M and for 150 minutes of leaching time. The dissolution of vanadium in sulfuric acid shows that there are two stages in the kinetics of leaching. At the first 15 minutes, there is a sharp increase in the amount of vanadium extracted and at longer leaching time, the extraction increase slightly. In the present work, the shrinking core model (SCM) was used to describe the acid leaching of vanadium compounds. A summary of the controlling regimes in the SCM are examined below for short time (less than 12 min.) and long time (more than 30 min.) stages. So, it was found that the kinetics of leaching in both stages is controlled by solid product diffusion regime.

Sep 13, 2010

By G. M. Cresswell

The 2 360 t/h two module Phola coal preparation plant represents anew era of large plant in the Witbank coalfield designed to extend its life to 2020 and beyond. The plant uses the optimum processing model for Witbank coals, receiving a feed coal size of -50 mm, wet screening it into coarse and small coal fractions 50 x12 and 12 x0.63 mm before processing them in parallel through two primary DM cyclone sections, in order to make a 27.5 MJ/kg export floats product. The sinks are processed through a common high density DM cyclone section to produce a 21.5?23 MJ/kg thermal coal middlings product. The plant design incorporates the largest size DMS equipment used to date in South African coal preparation plants, i.e. 1 150 mm large diameter pump fed DM cyclones and 4.2 m width banana screens. The fine coal is conventionally processed by spirals, whereas the raw coal slimes are filtered using automated plate and frame filter presses and added to either the middlings or discards depending on its quality. The paper describes the database, innovative design concepts, construction, and commissioning.

Jan 1, 2010

An examination of the Census of Fatal Occupational Injuries (CFOI) data for the period 1992-1995 shows that 659 fatalities occurred in the mining industry as defined by the SIC. Oil and gas accounted for slightly more than one-half of all fatalities (figure 1-1). The coal industry had the highest fatality rate for the 4-year period, with 35.6 deaths per 100,000 full-time workers, followed by metal (23.1 per 100,000), oil and gas (23.1 per 100,000), and nonmetal (20.1 per 100,000). The fatality rate for all U. S. industries during this same period was 5.1 per 100,000 full-time workers. Figure 1-2 compares the fatal injury rates by year for the four major industry sectors of mining to the fatality rate for all industries combined. Figure 1-3 compares age-specific fatality rates in the mining industry to those seen for U. S. industry as a whole. Fatality rates for all industries combined were lowest for young workers and steadily increased in relation to workers' ages. In the mining industry, fatality rates by age group show a U-shaped curve. Young workers under 20 years of age had the highest injury rate (54.6 per 100,000), followed by workers aged 20-24 (50.8 per 100,000) and workers over age 65 (37.7 per 100,000). Table 1-1 shows the distribution of injuries by type of injury event. The mining industry, in comparison with all industries, had a considerably larger proportion of fatalities classified as caught in or crushed by collapsing materials (9.1% and 1.9%, respectively) and fires and explosions (10.0% and 3.1%, respectively). Transportation events comprised the largest proportion of fatal injuries in both the mining industry and all industries. Within the mining industry only, transportation accounted for the largest proportion of fatalities in all mining sectors except coal. A more detailed examination of the transportation events within the mining industry showed that highway incidents (50.5%) were the most common, followed by nonhighway incidents (22.2%), pedestrian incidents (10.6%), and those incurred during rail, water, and air transport (15.7%). Incidents involving caught in or crushed by collapsing materials comprised a higher percentage of injuries in the coal and metal sectors, while fall-from-height incidents were more frequent in the oil and gas sector. The classification system used in CFOI for type of injury event is not compatible with any variables contained in the MSHA data; therefore, direct comparisons are not attempted. [ ]

Jan 5, 2000

WMC was a late entrant into Indonesia in mid-1996, but had considerable experience and success in exploring in Asia, particularly the Philippines since 1988. Given the geological similarities to the Philippines and IndonesiaÆs superior æcradle to graveÆ Contract of Work (CoW) tenure system, the entry into Indonesia was a logical decision but nonetheless a result of detailed planning. At the time of WMCÆs entry, Busang in Kalimantan was still a 60 moz wonder and the euphoria of this apparent discovery had overflowed into every aspect of exploration. Many junior mining companies and tenement speculators were clamouring for properties in Kalimantan, whilst other serious and capable explorers had to compete for properties and exploration personnel in an era of high and often unrealistic expectations. The picture in late-1998 and through 1999 is dramatically different, as the worldwide downturn in the price of most metals coincides with financial and social crises throughout most Asian countries. The impact of this has been particularly severe in Indonesia and when coupled with the negative sentiment of the Busang fraud has resulted in an exodus of junior companies and also some of the majors. This is understandable given the much publicised social unrest, uncertainty of government, mooted changes to the eighth generation CoW, increasing illegal mining and heightened community expectations. The reality however is somewhat different and although clearly a crisis in many respects, it is also a time of great opportunity.

Jan 1, 1999

Mining companies in order to compete and succeed in being viable business propositions must look to the future and select mining methods which guarantee improved efficiency and productivity as well as lower costs. A mining company in adopting a method of mining must now select the equipment most compatible. To some mines compatible equipment may mean the use of drilling jumbos to replace hand held rock drills or the use of load haul dump units to replace scrapers. To other more mechanised mines compatible equipment may mean the use of raise borers and road heading machines. The right decision will be where equipment compliments method in such a way that the working environment is improved, productivity is maximised, cost if reduced and all profit opportunities are optimised. An example of such is where the use of improved mining techniques in underground operations may see cut off grades reduced. By selectively mining these lower grade orebodies, smaller operation's ore reserves improve and the capacity for continued growth is enhanced.

Jan 1, 1990

This paper describes the excavation of No. 1 Power Station Lift Shaft at the Kiewa Hydro-Electric Project. The advantages and limitations of the borehole method are outlined, and general principles of plant design are discussed.INTRODUCTIONFor many years, attempts have been made to reduce mine development costs by various methods. Some of the, techniques of tunnelling have been adopted in horizontal headings, and in main vertical shafts, mechanical plant has displaced hand labour with notable success. However, in the field of small rises and winzes, improvements have largely been effected by attention to details of procedure. The most promising avenues for' substantial reductions in cost relate to:(a) Long-hole drilling(b) The borehole method(c) Calyx drilling.Whilst each of these methods has its peculiar advantages, the borehole rising method is probably most useful, and capable of wide application.In brief, the borehole method of rising requires a, drill hole parallel to the axis of the rise. A hoisting rope is passed through the borehole, and is attached to a platform on which the rising crew are raised with their equipment to the drilling position in the rise.When properly planned, the method is particularly safe, and has generally received the approval of mine inspectors and safety authorities. Rising work is generally hazardous, even when special timbering methods are used. In...

Jan 1, 1959