Search Documents

During the development of Lorca tunnel project in the South-East of Spain, an in-site study has been done, with the purpose of obtaining the characteristics of the different lithological units through twenty-two parameters for the design of the tunnel excavation and support. In the paper both the different works developed and the different methods and criteria followed in the obtention of the parameters are described. The values of those parameters may be useful in similar cases. Also a summary-table of the parametrical characterization for the use in similar studies is given.

Jan 1, 1987

In most mines using presplitting the final excavated wall shows a zone of damage just below the crest and well defined presplit half barrels. The crest damage (surface dilation) zone varies and is added to by subsequent adjacent perimeter blasting operations. Keeping the preconditioning to a minimum is possible using the methods described in this paper, developed on several diverse and geographically distant mining operations to control crest dilation and preconditioning by presplitting in advance - not just laterally but vertically in advance. The first documented case (Delbridge, Marton and McSweeney, 2004) in the development of the concept was undertaken at AngloGold Australia Pty Ltd's Sunrise Dam Gold Mine (SDGM), located beside Lake Carey, some 730 km northeast of Perth, Western Australia. The mine had been developed in a series of cutbacks to a depth of over 300 m and began underground mining during the latter stages of open cut operations. This mine is fairly unique in that it utilised a single pass vertical presplit which initially extended over three bench heights and after the failure mechanisms were understood, over four benches. The presplit drilling for the three stacked benches started on the floor of the second bench so that any dilation was confined to the surface one bench above the crest and modified perimeter blasting was then developed to curtail damage from blasting adjacent to the new crest. The second case is based on a South African coal mine in the Witbank Coal Measures, 140 km northeast of Johannesburg, Republic of South Africa (RSA). It was important that blasting for optimal wall stability and minimal scaling was developed in advance. A dragline is scheduled to excavate the #2 seam midburden which is the lowest of the economically viable coal seams in the five seam Witbank Coal Measures. Mining of the overburden, coal and partings above the dragline midburden pass are by excavator and truck and each mining layer is individually blasted. The results of presplitting the midburden through the overlying coal seams and partings have provided a presplit with no surface dilation of the midburden crest and ensures any subsequent crest loss is solely due to blasting adjacent to the vertical presplit. Typical of all coal mines in South Africa only vertical presplits are used. Wall control is most commonly delivered by presplit blasting and one common sight after the dust clears is a ridge of broken blocks along the presplit row, usually with a main crack running between the presplit blastholes and often parallel cracks either side of the perimeter line. The surface rock strata or block structures have been dilated by the venting gases and shock waves. Decoupled, fully coupled, single or double deck charges are used depending on a variety of factors, anecdotal practices and perceived benefits. Preconditioning of the crest rock by blasting from above may not be visible to the naked eye (or non-existent in overburden in strip coal mines) but the high speed venting of explosives gases (and often the water in the presplits) preferentially follow existing cracks and structures because there is no developed presplit crack near the surface. This nearly always lifts, shifts and separates the surface structures and geological layers. Stopping the dilation by 'sacrificial' or 'in advance' presplitting has been shown to reduce the crest loss at both metal and coal mines. Drilling and presplit blasting through an upper level of bench or layer provides a degree of restraint to the target layer where the crest must be maintained and any damage caused by the venting gases will not cause concern as it is removed as planned, leaving a stable crest.

May 1, 2010

By D. G. Wymer, A. G. du Plessis, N. C. Joughin

The use of a dense hangingwal-support configuration extending right up to the face would enable greater levels of safety and productivity to be achieved in stopes, and becomes a practical proposition if water jets are used for stope cleaning. Such an arrangement opens the way for extending the use of water hydraulic power to the whole stoping operation. This, in turn, can provide further productivity benefits and significant savings in working costs. With al the necessary equipment being available, such a system could be introduced immediately, although the designs of props and rockdrills are not yet ideal.

Jan 1, 1989

By Peter C. Lighthal, Harvey N. McLeod, Iain G. Bruce

This paper describes the practical aspects of handling cyanide leach tailings. Alternative systems for cyanide destruction are briefly discussed. The provision of adequate retention time to allow natural degradation of cyanide during summer months is the most economical method of cyanide destruction. Cyanide in ground- water can frequently be both persistent and mobile, so that tailings basins should be designed to limit seepage. Common methods for limiting seepage are presented. Other aspects addressed are water balance, winter operation and abandonment of cyanide tailings systems. A case example of the Cheni Gold Mines Lawyers Creek Project tailings handling system is presented.

Jan 1, 1987

By Robert P. Kudlawiec

The use of Mobile Roof Supports (MRS) in pillar retreat mining has been a fairly recent occurrence in coal mining operations in the United States (1988). Determining the pillar block configuration, the crosscut and entry centers, the number of entries developed, the method of ventilation, and the type and mixture of equipment used arc all factors in establishing a successful pillar retreat operation. This paper will evaluate and report on the history of one coal company's relationship with MRS usage for pillar retreat mining and focus on the company's use of horizontal pillars (inverted-blocks) for the panel configuration.

Jan 1, 2000

By F. Raupp-Pereira, G. G. Cunto, J. A. Junkes, D. Hotza, V. P. Della

"The present work investigated the valorization of wastes as alternative raw materials for ceramic industries. Different industrial wastes based on the SiO2-Al2O3-CaO system and classified as non-hazardous were selected: sludge from varvite cutting process, sludge from gneiss breaks processes, sludge from filtration/clarification of potable water and a clay classified also as waste. All as-received residues were characterized by X-ray fluorescence, differential thermal analysis, thermogravimetry and particle size distribution. The applicability of these materials in ceramic formulations was then evaluated. The formulated mixtures were subjected to forming by pressing and extrusion followed by thermal treatment. After optimization of the processing conditions, the properties of the samples sintered at different temperatures were also evaluated. The waste materials studied proved to be alternative raw materials to natural mineral resources for the ceramic industry.IntroductionOne of the most important problems that have accompanied the humanity in recent decades is the environment’s degradation. In the same context, the natural resources exploration and technological development are phenomena which, if aren’t controlled, can cause ecological disequilibrium with unpredictable consequences [1]. It is in this perspective that recycling of various wastes assumes relevant importance.The recycling, understood here as the waste process reuse, is a common practice in the First World countries, where the raw materials have strategic aspects and the disposal techniques of solid wastes have considerable economic costs. In Brazil, the ecological conscience begins to be aroused due to, in the last ten years, the implementation of stricter laws for environmental control, in general, and licensing of waste generating from industrial activities, in special. The terms “residue” or “waste” are normally used to describe what remains of a production process; when an application for this material is not found. When wastes or residues are susceptible to be incorporated as raw materials or energy sources in a new material production, they can be understood as by-products [2].The valorization of industrial wastes is important, due to the need to pollute less and give an ecologically correct destination for wastes. The waste recycling, independent of its kind, presents several advantages in relation to using primary natural resources, such as reduction in the volume of raw materials extraction, lower energy consumption, lower levels of pollutant emissions and improvement of the health and safety of the population. The most visible advantage of recycling is the preservation of natural resources, extending its life and reducing the destruction of landscape and ecosystems [3]."

Jan 1, 2008

Gentlemen.-It is pleasant to be able to report that the year just closed has been a prosperous and successful one for the Institute. As is shown by the reports of the Treasurer and the Finance Committee, the business affairs of this organization are in excellent condition. With property valued at more than three-quarters of a million dollars, and with considerable sums in various funds and endowments, it is possible to spend on each member of whatever class $22.65 each year, more than the maxi- mum amount of dues received from any one, and substantially twice the average amount, $10.94, received from all. To do this has required close management and a strict regard for our limitations. In 1926, when the Budget was made up, the estimated expenditures for the work which it was felt the Institute must do exceeded the estimated receipts by some $14,000. At the close of the year, despite a number of unexpected decreases in receipts, it had proved possible to accomplish substantially all the work laid out and close the books with the usual transfer of initiation fees to the General Reserve, and still only reduce the cash balance $2,074.54. This was made possible by the hearty and loyal cooperation of the whole staff of employees and the extremely large amount of gratuitous service rendered by the officers, the members of the Divisions and technical Committees, and the membership generally. Even so it was impossible, because of limitations of funds, to undertake many things it is highly desirable for the Institute to do, and it was necessary to refuse the publication of important papers and committee studies, because of the lack of funds. PUBLICATIONS In an analysis of the income and expenses of the Institute published in the February issue of our Journal, MINING AND METALLURGY, it was pointed out that the largest item of expenditure is, as it should -be, for publications. Printing, binding, and distributing the various technical papers sent to the members cost in 1926 more than all the money received from dues, including the portion allocated as subscription to the magazine. Within the. year, the following volumes were printed and, with the exception of the second volume of TRANSACTIONS, which was mailed in January, were distributed : TRANSACTIONS, Volume 73, 1241 pages, covering papers on non-ferrous metallurgy, milling and concentration, non-metallic minerals, iron and steel, and the Institute of Metals Division papers read at the

Jan 1, 1928

By Kristian Drivenes, Steinar L. Ellefmo, Kurt Aasly, Ben Snook, Przemyslaw B. Kowalczuk, Rolf Arne Kleiv

"Since Ellefmo et al. (2014) published resource estimates of undiscovered seafloor massive sulfides (SMS) on the Arctic Mid-Ocean Ridge (AMOR), there has been an increased focus on establishing new knowledge about exploitation technologies for such deposits. This also includes understanding the process mineralogical properties of typical SMS deposits.The part of the AMOR that lies between Jan Mayen and the Svalbard Islands and is located within Norwegian jurisdiction and, as such, investigating the potential for mineral production from hydrothermal vent fields has been seen as strategic. The AMOR has been explored for active hydrothermal vent fields since early 2000s (Pedersen et al., 2010b). One of the active vent fields discovered, Loki´s Castle, is located in the northern part of Mohn´s Ridge. This vent field was first described by Pedersen et al., (2010a) and consists of two mounds, each approximately 100-150 m diameter and 20-30 meters high, hosting several active chimneys, up to 11 m high.Loki´s Castle has been selected as a case site in order to study the properties of typical SMS occurrences with respect to possible future deep-sea mining activities. As part of the MarMine cruise in 2016, the Loki Castle was visited and sampled for e.g. mineral characterization and mineral processing analyses. In total, more than 500 kg rock samples were collected using ROVs, and intended for further research (Ludvigsen et al., 2016). In addition to sampling mineralized rock fragments, survey data like bathymetry, magnetics and Underwater Hyperspectral Imaging (UHI) was collected using Automated Underwater Vehicle (AUV)."

Jan 1, 2017

By Dennis V. D’Andrea, Robert C. Steckley, William C. Larson, Richard A. Dick

A fragmentation experiment was performed in cooperation with Duval Corporation in a porphyry copper molybdenum deposit near the Sierrita pit south of Tucson, Ariz. A 10-hole test blast was detonated to establish relationships between blasthole spacing and the resulting fragmentation. Blastholes were 9 in. in diameter and 110 ft deep. The 10 blastholes contained a total of 17,400 lb of aluminized slurry blasting agent in 50-ft columns with 60 ft of stemming. Blasthole spacings of 25, 20, and 15 ft were tested. Diamond drill core examination was the primary method used to determine the condition of the rock before and after blasting. Topographic surveys were used to measure the rock swell produced by the blast and a fragment size distribution was obtained for the rubblized material on the surface. The rubble zone at the surface was ideal for in situ leaching. Fragmentation to depths of 110 ft was excellent from the 15- to 20-ft blasthole spacing patterns. Good breakage was also produced by the 25-ft pattern although the effects of the blast were not as obvious. In situ leaching tests were not conducted. However, based on size consideration only, all three blasting patterns produced adequate breakage for successful leaching.

Jan 1, 1974

By B. J. Moore

This Bureau of Mines publication estimates that U.S. helium resources as of January 1977 were 710 billion cubic feet. These resources are broken down into four classifications, as follows: Helium in measured natural gas resources and in storage, 201 billion cubic feet; helium in indicated natural gas resources, 150 billion cubic feet; helium in hypothetical natural gas resources, 175 billion cubic feet; and helium in speculative natural gas resources, 184 billion cubic feet.2 Most of the helium in natural gas is presently dissipated as natural gas is consumed as fuel and for other purposes. Helium resources of the United States may also be divided into three other categories: (1) Depleting and undiscovered natural gas resources, 589 billion cubic feet; (2) nondepleting natural gas, 83 billion cubic feet; and (3) storage, 38 billion cubic feet, of which 37 billion cubic feet is federally owned and 1 billion cubic feet is privately owned. The United States does not have any significant leasehold rights in the depleting fuel gas resources. However, through the Department of the Interior, it does have leasehold rights to about 70 percent of the helium found in nondepleting natural gas, and it owns over 90 percent of the helium in storage.

Jan 1, 1979

By P. Kovalchik

The Bureau of Labor Statistics (BLS) classifies hearing loss as a separate illness category. Hearing loss accounted for 11% of all illnesses in 2005 (U.S. Department of Labor Bureau of Labor Statistics, 2006a). According to occupational data for coal mining provided by the Mine Safety and Health Administration (MSHA) from 2000 to 2005, operators that exceeded 100% noise dosage were from only seven types of machines: auger miners, bulldozers, continuous mining machines, front end loaders, roof bolters, shuttle cars (electric) and trucks (Title 30 CFR Part 62, 2000-2005). Roof bolting machine operators rank second among all underground machine operators that exceed 100% noise dose. There are approximately 600 underground coal mines with 3,930 roof bolting machine operators (U.S. Department of Labor, Mine Safety and Health Administration, 2005; U.S. Department of Labor Bureau of Labor Statistics,

Jan 1, 2008

By M. Dworzanowski

The physical beneficiation of iron ore that has a wide particle-size distribution is problematic, regardless of the process applied, whether dense medium separation, gravity concentration, magnetic separation, or flotation. The problem of particle size is further compounded when there is a significant -10 µm fraction. Generally the approach to a wide particle-size distribution is to split into narrower size ranges and treat each separately. More often than not the -10 µm fraction is not treated but discarded. This approach results in a more complicated and expensive flow sheet and the loss of any potential value in the -10 µm fraction. Wet high-intensity magnetic separation (WHIMS) bench-scale test work was conducted on a haematite-rich material with a particle size of -200 µm. What made this material different was that it contained a 60% -10 µm fraction, hence discarding the -10 µm material was not an option. The objective of the test work was to determine how to maximize the recovery of the haematite across the full particle size range. Given the unusual particle size distribution, it was concluded that WHIMS would be the only practical beneficiation route. The -200 +10 µm and -10 µm fractions were treated separately and together under varying WHIMS conditions. For a given concentrate grade, the mass yield obtained was greater when the total particle-size distribution was treated. The inferred optimum conditions, using the same material, were tested on a pilot-scale WHIMS and similar results were obtained.

Jan 1, 2014

By R. S. Conti

The US Bureau of Mines (USBM) has developed an inflatable feed-tube seal (IFTS) for high-expansion foam generators. The IFTS is a lightweight, portable, rectangular inflatable bag that can be used by firefighters to rapidly seal large openings, such as those in underground mines, and to simultaneously provide a feed-tube for a high- expansion foam generator. Thus allows fire-fighting foam to freely flow to the fire site and control or extinguish the fire. Studies indicated that a high-expansion foam plug will travel 183 m (600ft) down an entry with a 4.5% rise in elevation, before leakage of foam from around the inflatable partition.

Much of the data required for the evaluation of mine design is obtained from bore cores. It is essential to collect data that is useful and not to overlook features which might have adverse effects upon the mining practices and which might not be readily discernible to the untrained eye when examining bore cores. Interpretation of the data has progressed from the use of single-value properties, such as ultimate compressive strength or Young's modulus, to the utilisation of most measurable quantities. The simulation techniques used employ physical and mathematical models for prediction of mining conditions or strata behaviour. The application and capabilities of these methods to mine design are discussed.

Jan 1, 1977

By R. V. Ramani, Christopher J. Bise, Robert Stefanko

Over 200 billion tons of coal reserves lie locked up in deposits west of the Mississippi River-and of this, well over 100 billion tons are recoverable only by underground mining methods. Yet, because of the associated problems of unfavorable economics and inadequate technology, western underground mines contribute less than 2% to the annual US coal production. In order to reach the billion-ton coal production level called for by President Carter, it a pears the majority of new coal development will come from the West. But for this to be possible, new mining methods and equipment must be designed to match the unique thick seam conditions.

Jan 10, 1977

By Leonid Bryner

For many years, geologists have inferred a connection between the evolution of the earth's crust and ore deposition, a connection coming under the heading of metallogeny. In recent years the concept of metallogeny has assumed major importance in the exploration planning of Russian geologists in their quest for new mineral sources. As defined by Radkevich, metallogeny is "the science which studies the laws governing the distribution of ore deposits in the earth's crust." However, since it can be argued that metallogeny does not contain enough certitude to be classified as a "science," it would be more appropriately defined as the study of metallogenic provinces, and metallogenic epochs.

Jan 6, 1963

By John Turney, John Gathje, Donald Gale

The Eskay Creek deposit, located in northern British Columbia, is a high-grade gold/silver ore associated with complex polymetallic sulfides. Process development began in 1989 and continued through 1993. Because of the refractory nature of the ore, options including roasting and smelting were investigated. The selected process of pressure oxidation was the basis for basic engineering design until a re-evaluation of economics and risk indicated a preference for toll smelting. Although well proven in many industrial applications, pressure oxidation of the Eskay Creek ore dictated several innovations to solve problems associated with silver jarosite formation, preg-robbing, and high soluble copper and zinc concentrations.

Jan 1, 1995

By R. Hogg

The mathematical description of solids transport in mills is an important aspect of the development of comprehensive models for the analysis, simulation and control of grinding systems. The basic mechanisms of particle transport and mixing, including gravity flow, carrier fluid transport, and "diffusion", are reviewed and their relative importance in wet and dry ball mills is discussed. Specific models for transport and mixing in dry, grate-discharge and wet, overflow ball mills are described. The limitations of the models, parameter estimation problems, scale-up criteria etc. are discussed and the conditions which lead to particle size dependent transport, and hence to internal classification in the mill, are described in detail.

Jan 1, 1984

By R. P. Killmeyer, B. S. Gottfried, J. T. Wizzard

The US Department of Energy's Coal Preparation Branch has developed a computer program to calculate the performance characteristics of coal washing devices. This program uses specific gravity analyses of the clean coal and refuse streams as input, and generates dependent and independent performance criteria for the washer. Partition curves are internally represented in a functional form by a Weibull function. Comparisons are made between performance criteria calculated by hand and the performance criteria calculated by the program for 120 different dense medium cyclone tests. Results show that the computer program gives results in close agreement with hand-calculated values while greatly reducing the amount of time involved in performing the analyses.

Jan 1, 1984

By Walter F. Gries

AN ounce of prevention is worth A a pound of cure' is an old proverb that has sometimes been forgotten in programs having to do with the health of workmen. Realization of the truth of this maxim is increasing, however, and today the iron-mining industry, with which I am particularly concerned, is becoming more alive to the prevention of illness and the conservation of health, thus decreasing the need for treatment after diagnosis has established its necessity. The healthy workman is the happy, efficient workman, and new programs tending to make him more health-minded are being put into operation. Preventive medicine is less costly than corrective medicine, to say nothing of the better results obtained. Periodic physical examinations, with close follow-up attention when required, have reduced the time lost because of illness, workmen's compensation costs, and group-insurance benefits for nonindustrial disabilities.

Jan 1, 1939