Search Documents

The basic methods to remove material from underground mines are to: convey continuously, batch in trucks, or batch in a shaft hoisting system. A critical aspect in shaft hoisting is accurately batch loading the conveyance or skip. During the 20th century, the almost universally accepted method of loading was via a measuring flask. A measured quantity of material was filled into the flask as the conveyance traveled through the shaft and then, when the conveyance arrived at the loading position, it was ædumpedÆ into the skip for hoisting. Two skip loading conveyor systems have been developed in Australia: BHP BillitonÆs Cannington Hoisting System, installed in 1996, is believed to be the first conveyor loading system designed for two skips. Two parallel conveyors were installed with a two-way gate controlling feed onto each belt. Cannington was ideally suited to conveyor loading as the very high ore density and relatively low production rate required a relatively small volumetric storage capacity on the weighed belt. Newcrest MiningÆs Telfer Hoisting System, which is to be commissioned in 2005, consists of a single slewing conveyor loading each skip with 32 tonnes of ore. The development of this system eliminates the two-way transfer, improves the accessibility and minimises the excavation required. While every hoisting system must be considered on its merits, conveyor loading offers significant advantages to the Mining Industry in the 21st century.

Jan 1, 2005

By R. S. Rickard, B. Ball

INTRODUCTION Pyrite responds to the flotation reagents normally used in sulfide flotation systems. For example, it is well known that xanthates are good collectors for pyrite, and cyanide, sulfide and hydroxides are depressants. The particular response of pyrite to these and other reagents is used to advantage in several areas. By careful control of depressant and collector additions, pyrite can be separated from other sulfides by flotation. This is of obvious importance in base metal sulfide flotation where pyrite depression is often required to produce a marketable grade concentrate. Flotation of pyrite has long been employed in gold ore processing, and it appears that pyrite flotation from coal may become important in the future (1). It is probably a direct consequence of this relative ease of separation, plus the low economic value of pyrite, that detailed investigations on the chemistry of its flotation and depression are relatively limited. Gaudin (2, 3, 4) and others, in the mid-1950's published data on the flotation of pyrite, but detailed or consistent mechanisms were lacking. In 1955, Sutherland and Wark's book (5) was published, in which a large , amount of empirical information, especially earlier work of Wark and Cox, was presented. More recently, in 1968, significant contributions have been made by Fuerstenau et al. (6, 7) and Majima and Takeda (8). These papers introduced electrochemical explanations of the effects observed with xanthate and cyanide ions.

Jan 1, 1976

Develop a safe, efficient filter for removing diesel particulate matter (soot) from the exhaust of underground mining machines equipped with water scrubbers. Approach The Bureau of Mines and the Donaldson Company, Inc., jointly developed a low-cost, disposable, pleated-media filter (PMF) system. The system is intended for use on Part 36 permissible equipment or other machines equipped with water scrubbers. The PMF is installed downstream of the water scrubber to take advantage of the cool exhaust produced by the water bath. This demonstration system was tested on three Jeffrey 4114 Ramcars and a Wagner LST-5 scoop at Utah Fuel Company's Skyline mine near Scofield, Utah. Figure 1 illustrates a clean filter element being inserted into the canister on the Ramcar. How It Works The PMF system consists of a water trap, an optional over-pressure relief valve, filter canister, and PMF Under normal operations exhaust from a vehicle equipped with a water scrubber is heavily laden with water, especially on immediate startup of the engine. The water trap is designed to remove most of the water droplets from the exhaust before they enter the PMF, thus improving PMF performance. The over-pressure valve is designed to limit the exhaust backpressure by venting off some exhaust gas before the: filter. It is attached to the water trap upstream of the PMF. Figure 2 illustrates and shows a break out sectional view of the location of the PMF on the Ramcar.

Jan 1, 1991

By F. Cadena

HIWASSEE Dam, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are pres-ent in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about 1/4 in. maximum size, although the bulk of the deposit is medium grain. Exten-sive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chicka-mauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrange-ment of equipment if the optimum in flexibility and capacity is to be attained.

Jan 1, 1939

By R. S. Rickard, B. Ball

INTRODUCTION Pyrite responds to the flotation reagents normally used in sulfide flotation systems. For example, it is well known that xanthates are good collectors for pyrite, and cyanide, sulfide and hydroxides are depressants. The particular response of pyrite to these and other reagents is used to advantage in several areas. By careful control of depressant and collector additions, pyrite can be separated from other sulfides by flotation. This is of obvious importance in base metal sulfide flotation where pyrite depression is often required to produce a marketable grade concentrate. Flotation of pyrite has long been employed in gold ore processing, and it appears that pyrite flotation from coal may become important in the future (1). It is probably a direct consequence of this relative ease of separation, plus the low economic value of pyrite, that detailed investigations on the chemistry of its flotation and depression are relatively limited. Gaudin (2,3,4) and others, in the mid-1950's published data on the flotation of pyrite, but detailed or consistent mechanisms were lacking. In 1955, Sutherland and Wark's book (5) was published, in which a large amount of empirical information, especially earlier work of Wark and Cox, was presented. More recently, in 1968, significant contributions have been made by Fuerstenau et al. (6,7) and Majima and Takeda (El. These papers introduced electrochemical explanations of the effects observed with xanthate and cyanide ions.

Jan 1, 1976

By D Craw

The Hyde Macraes Shear Zone is a mineralised low-angle shear within the Otago Schist traceable for ~30 km with a NW strike. It is been actively mined along 12km of this strike, producing >6 Moz of gold. The shear zone consists of greenschist facies rocks with a mineralogy only subtly different from that of the host schist. Pervasive fluid flow has occurred along grain boundaries and within microshears which have been enhanced by the deposition of hydrothermal graphite. We model the development of these microshears using a threedimensional numerical code. For an inhomogeneous initial rock with lithostatic fluid pressures and a dynamic permeability deformed under dextral non-coaxial flow, deformation is distributed into weak shear bands. Graphite deposition and associated reaction-softening has a dramatic effect on the development of model shear zones. Graphite is deposited into a shear band, weakening it and further localising the deformation into that shear band, producing an anastomosing and interconnected shear zone structure such as observed in the HMSZ. The degree of graphite precipitation and graphitic-induced weakening are varied in the models. More graphite precipitation with a low degree of reaction-softening results in more diffuse shear bands. In contrast less graphite deposition but with a high degree of reaction-softening more leads to the development of more focused shear bands. Graphite deposition has clearly controlled the formation of the HMSZ structure, and is an important indicator of potentially mineralised structures elsewhere.

Jan 1, 2007

By David Conover

Knowledge of the magnitude and direction of the horizontal secondary principal stresses is a critical factor in designing the layout and mining sequence of underground openings. Typically, horizontal stress measurement has been accomplished using overcoring or hydraulic fracturing. Hydraulic fracturing can be accomplished from surface boreholes prior to development, but the technique relies on numerous assumptions regarding the rock mass and the stress field, and interpretation of results is somewhat subjective. Traditional overcoring provides a more precise measurement, but requires underground access. To allow for precise measurement of the horizontal stress field from surface boreholes, the In-situ Stress Tool (1ST) was developed by SIGRA Pty of Brisbane, Australia. Used in conjunction with HQ wireline coring, the 1ST contains a battery-powered data logger that records tool orientation and monitors six diametral deformations as the tool is overcored. The IST has been used successfully for several years in Australia, but has only recently been introduced in the United States This paper discusses how the IST was used to measure the pre¬mining horizontal stresses at a western U.S. coal mine. Seven successful measurements were obtained in two holes at depths ranging from 250 to 800 ft. Results were consistent, showing moderately biaxial stresses greater than those expected from gravity loading, but relatively low compared to rock strength. In addition to describing the overcoring equipment and procedures, various problems encountered during testing and the accuracy of the results will be discussed.

Jan 1, 2004

By M. C. Bétournay

Strainbursts are common in overstressed brittle rock around deep mine openings. Such failures are characterized by a biaxial state of stress in the plane of the opening boundary. A zone of compressive stresses imposes initial failures near or at the surface of the opening that results in spalling of thin slabs of rock roughly parallel to the free face. While the failure of rock under biaxial loading conditions is increasingly common in deep underground mines, only a few representative laboratory studies have been reported in the literature, without emphasis on rockbursting aspects, and none in the last decade. This paper presents the results of a testing program on a granite rock type. Biaxial testing, conducted on 100 mm cubic samples, was carried out to examine the influence of lateral confinement and loading rate on the rock’s ultimate strength. The paper reports the test results in terms of normalized biaxial failure envelope s1/sc-s2/sc. A discussion of the failure mechanisms observed is presented. Les coups de toits de déformations sont choses communes dans le rock cassant surcontraint en place autour des ouvertures minières profondes. De telles ruptures sont caractérisées par un état de contraintes biaxiales dans le plan de la périphérie de l’ouverture. Une zone de contraintes compressives impose des ruptures initiales à ou près de la surface de l’ouverture, qui produit des relâchements de minces plaques de roc plus ou moins parallel à la surface. Bien que les ruptures de roc sous des conditions biaxiales sont de plus en plus communes dans les mines à grandes profondeurs, il n’y a eu que quelques études représentatives en laboratoire de publiées, sans emphase sur des aspects de coups de terrains, et aucunes publiées depuis la dernière décennie. L’article présente les résultats d’une campagne d’essais appliquée à un type de granit. La campagne d’essais biaxiaux, sur des échantillons cubiques de 100 mm, avait pour objectif d’examiner l’influence du confinement latéral et le taux de chargement sur la résistance ultime du roc. Cet article fait part des résultats en terme de l’enveloppe de rupture biaxiale normalisée s1/sc-s2/sc. Une discussion sur les mécanismes de ruptures observés est présentée. Dehnungsbrüche findet man häufig in übergespannten spröden Felsen um die Öffnung von tiefen Minen. Solche Brüche sind von einer zweiachsigen Spannung in der Ebene der Grenze der Öffnung charakterisiert. Eine Zone von Druckspannungen verursacht initiale Brüche, entweder an der Öberflache der Öffnung oder in der Nähe. Davon scheiden sich dünne Felsplatten mehr oder weniger parallele mit der freien Wand. Obwohl Felsbrüche unter zweiachsiger Beanspruchung immer mehr häufig in tiefen Minen beobachtet sind, hat man über nur einige repräsentative Laborversuche in der Literatur berichtet. Diese Studien diskutieren das Thema ohne Betonung auf Felsbrüchen, und keine sind in den letzten zehn Jahren erschienen. Die vorliegene Arbeit gibt die Ergebnisse eines Testprogramms auf einem Typ von Granitfels. Durch zweiachsige Prüfungen von kubischen Proben mit Seitenlangen von 100 mm sollte man den Einfluss von seitlicher Ermittlung und der Beanspruchungsrate auf die Bruchfestigkeit des Felsen studieren. Man findet auch die Prüfergebnisse in bezug auf das normalisierte, zweiachsige Bruchkriterium s1/sc-s2/sc. Die beobachteten Bruchmechanismen sind auch diskutiert.

Jan 1, 2003

By Steve Griles

Mr. Griles did not make his speech available for reprint. Looking Down the Road: The Environmental Side of the 1990s and Beyond Environmental Social Responsibility Love Canal, Buffalo Creek, Widow Combs, Bohpal and Three Mile Island are familiar names to all of us-names which evoke memories of environmental tragedies. These memories, as well as memories of other environmental disasters, lead us to pose this question: What is the nature of the environmental social contact between industry and society? The manner in which one answers this question will. in large measure, answer the question of where one thinks environmental issues will go, or should go, in the 1990s and beyond. The history of the evolution of the environmental movement will be helpful in defining and under- standing just what society's environmental responsibility is and, perhaps, what it will be. To Define the Future Start With the Past The common law, which most of the United States adopted from the English system of jurisprudence, traditionally considered pollution control and other environmental issues to be a matter of determining the relative rights of private property owners and of individuals. Legal and equitable theories, such as nuisance, negligence, trespass and the law of riparian rights, were utilized to allocate responsibilities between parties under the common law. The discharge of pollutants into streams and into the air was by and large considered acceptable, at least up to the point that another's "reasonable" use of the same air or waterway was significantly impeded. Further, the judicial decisions interpreting the applicability of the common law to the protection of the environment generally reflected the social and economic pressures of the age. During the Industrial Revolution, the decisions and policies had a marked tendency to favor industrial development. Jobs and industrial growth are deemed as important, and in some cases more important, than the protection of people and property. Additionally, the idea of a social responsibility, beyond that owed to a competing land or water user, was nearly alien to the early common law.' One could even go so far as to say that, had there been a social environmental contract under early common law (which, of course, there was not); but if there were, it would have been to promote actions which facilitated industrial development, even at the expense of the environment. Post-World War LI industrial expansion brought with it a growing awareness of limits on the environment's ability to absorb increasing levels of pollution. Thus evolved an era of social and political adjustment, as society began to shift away from supporting big business and industrial development and toward supporting domestic government programs and limits on industry. States gradually stepped in with efforts to address environmental issues. The Pennsylvania Clean Streams Law and the West Virginia Surface Mining Act of 1939, while lax in comparison to today's standards, nevertheless marked definitive efforts toward altering the balance between industrial development and environmental protection Pollution control continued to be viewed as a state responsibility through the 1950s, until Congress began, for the first time, to allocate funds for federal research on air and water pollution and to implement

Jan 1, 1988

By A. H. Daane, W. J. Wunderlin, B. J. Beaudry

The solid solubility of holmium in copper, silver, and gold, determined using metallographic techniques, was found to be a maximum of 0.06, 2.4, and 3.2 wt pct, respectively, nt the eutectic temperatures. The temperatures of these eutectic horizontals, determined by differential thermal analysis, were found to be 868", 787", and 778"C, respectively. The first compound on the silver-rich side of the Ag-Ho system was found to be A&Ho2. In a study by Gold et al.,' on the effect of small amounts of soluble impurities on the electrical resistance and thermoelectrical properties of copper, traces of iron were shown to have drastic effects on the thermoelectric power due to the magnetic scattering of the conduction electrons. Since little is known about the state of the iron ion when dissolved in copper, Gold had hoped to repeat these experiments using certain rare earths as the magnetic scattering centers; because of the tightly bound 4f electrons it is not expected that their spectroscopic state would be affected by alloying. In such an experiment the sole role of the trace rare-earth impurity would be to magnetically scatter the copper conduction electrons without producing appreciable distortions in the otherwise pure copper matrix. Since holmium was chosen for such a study because of its high magnetic moment, it was necessary to establish precisely its solid solubility in copper. The study was extended to include the solvents silver and gold, so that an evaluation of the data using classical solubility parameters could be made. No previously reported work on the systems of holmium with copper, silver, or gold was found in the literature. Information on the solubility of other rare earths in these three metals is also very meager. The solubility limit of yttrium in copper was reported as less than 1 wt pct2 and the solubility of praseodymium in gold as 0.35 wt pct,3 while no references were found on solubility studies of rare earths in silver. EXPERIMENTAL Materials. The materials used in this investigation were distilled holmium prepared in this Laboratory, OFHC* copper, electrorefined silver (99.9 *OFHC = oxygen-free high conductivity. pct), and gold with the analyses given in Table I. Sample Preparation. Samples weighing 1 to 2 g were prepared by arc-melting the components together on a water-cooled copper plate under purified argon atmosphere. The samples, turned and remelted at least five times to ensure homogeneity, showed weight changes of less than 0.1 wt pct after melting. Samples containing less than 0.7 wt pct Ho were prepared by diluting 1 to 2 wt pct Ho alloys with the pure solvent, while samples with concentrations greater than 0.7 wt pct Ho were prepared directly from the metals. The samples were wrapped in tantalum foil, sealed in outgassed Vycor tubing under helium, annealed at the desired temperature for at least 24 hr, and then quenched by shattering the Vycor tube in cold water. Metallographic Methods. Standard mechanical polishing methods were used in preparing the silver and gold alloys for examination, while the copper alloys were electropolished using a 40 pct solution

Jan 1, 1963

Coal is a very versatile resource, having variable characteristics and having potential for a wide variety of mar- kets. Australia has extensive deposits of black coal, although they are concentrated mainly in Eastern Australia. Assessments of the currently known reserves are related to the qualities of these reserves. Markets available to black coal fall into the broad groupings of metallurgical, fuel, conversion and miscellaneous markets and the requirements of these markets are related to coal characteristics. Market trends in Australia and on the export market are discussed and projected forward. By the end of this century Australian consumption of black coal could well be 100 million tonnes per annum, and, in the absence of any export restriction, a similar amount is likely to be exported. Currently defined black coal resources in Australia will last at least 600 years at these projected rates of consumption. Although the position appears satisfactory in considering the projected life of the black coal resources, there is a serious lack of detailed information on reserves, mining and preparation yields, quality and possible environmental restrictions. Action is required on three parallel courses: (1) a consistent, systematic and extensive survey of current coal resources in Australia, (2) accelerated exploration activity to define poorly prospected and potential areas, and (3) regular updating and extension of the knowledge of Australia's coal resources. This information would be of tremendous assistance for the formulation of a national energy policy on coal.

Jan 1, 1975

By Stanko Nikolic

Ferrous calcium silicate slags are potentially important for future practice in copper converting operations and processes and can be described by the ?Cu2O?-FeO-Fe2O3-CaO-SiO2 system. Despite its industrial importance the phase equilibria in this system have not been fully investigated. Characterization of this slag system is necessary to improve the design and optimization parameters of new processes, including fluxing and operating temperatures. Experimental methods have been developed to investigate the phase equilibria of these slags at copper saturation and without copper. This technique involved equilibration of samples at a fixed oxygen partial pressure, rapid quenching, and analysis of the compositions of phases using electron probe x-ray microanalysis (EPMA). Liquidus and solidus data are reported for the primary phase fields of spinel, wollastonite and tridymite at 1250oC and an oxygen partial pressure of 10-6atm. The resulting data has been used to construct liquidus isotherms in the ?FeO?-CaO-SiO2 system both in equilibrium with and without molten copper. The experimental results were compared with the predictions of a thermodynamic computer package utilizing a self consistent thermodynamic database. The predictions of the model were in good agreement with the experimental isotherms when projected onto the FeO-CaO-SiO2 section, however the copper concentrations in the liquid phase at copper saturation were lower than predicted using the current database of the model.

Jan 1, 2006

By A Specht, A Müller, V Montenegro, S Winkler, E Klaffenbach, A Schmidt

In the process of primary copper smelting in flash smelting furnace (FSF), the ratio of iron to silica (Fe/SiO2 mass ratio) primarily determines the slag viscosity and magnetite formation. Viscous slag does not only cause difficulties in daily operation, such as in tapping, it also increases the copper losses to slag. Thus, keeping the Fe/SiO2 mass ratio at the desired level is an important aspect of FSF and slag cleaning furnace (SCF) operation. In this study, the improvement of the Fe/SiO2 mass ratio was conducted in two steps: First, the optimal Fe/SiO2 mass ratio was derived based on thermodynamic data. Based on this analysis, appropriate control limits were determined. Second, this range of favourable Fe/SiO2 mass ratios was implemented into operation by an advice-based control system, which suggests the addition of silica based on the analysis of SCF slag. As this approach was successful, the same advice-based control system principle was adapted for the coke addition to the SCF. After testing the new advice-based control for several months, the production data confirm the predictions by thermodynamics: since the prediction was implemented as an advisor, the copper and magnetite content in SCF slag is significantly reduced and viscous slag is reported less often by operations.

Aug 21, 2024

By R. S. Montgomery

Laboratory experiments simulating rock drilling were conducted on a number of commercial grades of tungsten carbide in order to determine their wear rates when they are used as inserts in percussive rock drill bits. The test rock was Barre granite and tests were made at conditions similar to those of the carbide buttons near the periphery of a large, down-hole, button bit. In addition, some wear rate measurements were made at a low blow energy. Wear rates of these carbide buttons were an extremely sensitive function of their cobalt contents and hardnesses and were proportional to e-°.57Hup to a hardness of about 91 RA. The point of minimum wear rate, which occurs at about 92 RA, corresponds to the point of maximum compressive strength. Modern percussive rock drill bits have inserts of cemented tungsten carbide on their wear faces. These inserts have drastically reduced bit wear in comparison to that of earlier all steel bits. The most common cemented carbide grade used in percussive rock drill bits contains about ten weight percent cobalt, although grades containing more or less cobalt are also used. Contrary to the case with carbide in metal-cutting tools, alloying materials are rarely used in mining grades. There are a number of designs of rock bits in current use. The most common form is an X bit which has four chisel-form radial wings. The button bit is another important design and one which has been recently developed. This design uses a flat steel face studded with relatively small hemispherically tipped carbide buttons. These types are illustrated in Fig. 1. Studies have been made of the sliding wear of cemented tungsten carbide on rock 1-4 and multiple-impact fracture', 5-6, b~t there has been comparatively little published on the percussive wear of this material although the wear of the impact face is the most important. There is some available data on the rate of dulling of rock bit inserts in actual drilling 7 but no laboratory studies. Sliding wear studies are useful for understanding the wear of coal and mineral cutting tools and gauge wear of percussive drill bits. but the

Jan 1, 1970

By Steven G. Vick

Effects of the August 1995 failure of the Omai tailings dam in Guyana continue to be felt throughout the mining industry. This article is taken from the final report of the independent body of experts commissioned by the government of Guyana to establish the cause of the failure. It explains what happened, why and how to avoid it in the future. Despite environmental, health and safety effects that were negligible by any objective measure, the failure has received wide international attention. Coming on the heels of the shift in exploration targets and development opportunities to developing countries, it has intensified interest in tailings dam safety and environmental management issues. An informed understanding of the nature of the failure and its effects is key to responding to these concerns.

Jan 1, 1996

By Alan Jorgansen, Dave Hummer, Scott Scovira

Kennecott Energy's Colowyo Coal Mine is the largest open pit coal mine in Colorado and produces 5.5 MM tons per year. Colowyo uses the terrace mining method to recover up to seven seams of rolling coal ranging in thickness from 5 to 20 feet. Draglines are used to strip overburden ranging from 60 to 120 feet thick off two coal seams. These two seams are characterized by soft and fold fractured coal and in past practice cast blasting caused excessive coal damage. As a result, to ensure minimal coal damage and high coal recoveries, the overburden was excavated in two passes. The first pass removed the upper overburden to within 10 to 20 feet of the coal seam. The second pass removed the remaining overburden above the coal. Two-pass mining was effective in controlling coal damage, but also carried significant additional costs.

Jan 1, 2003

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rockmass strength. Past studies have largely used arbitrary scaling approaches to produce rockmass strength from laboratory rock tests. This paper proposes a stochastic approach to produce rockmass strength from laboratory rock tests. Based on the laboratory data, MATLAB with an extreme value stochastic model generated a database for each physico-mechanical property of the rock. Then finite-difference software FLAC2D simulated laboratory-sized rock specimens. Random material properties in MATLAB were generated using the grids developed in the numerical model. The random properties were then applied to the final FLAC2D model. Model runs simulated the approach performed in the laboratory. The results from the model indicate that a stochastic approach produced compressive strengths that were lower than those from the deterministic approach. Failure modes for each specimen were different from those observed in the laboratory. In addition, random density also influenced the failure mode, highlighting the importance of stochastic analysis in rocks.

By Edward L. McHugh

The Thousand Lakes Wilderness has no known economically significant mineral resources. However, the geologic setting of the Wilderness indicates a potential for the discovery of geothermal resources. INTRODUCTION The Thousand Lakes Wilderness occupies 16,335 acres (6,611 ha) in eastern Shasta County, California. A mineral resource study of the area was authorized by the Wilderness Act of 1964 (Public Law 88-577). Mining records and published information were examined, and field investigations conducted in 1979. The Wilderness is about 50 miles (80 km) east of Redding and 12 miles (19 km) south of Burney, California. It lies in the Cascade Range of California. Relief is more than 3,000 feet (910 m); elevation is greatest at the summit of Crater Peak, 8,677 feet (2,645 m).

Jan 1, 1982

By D A. Cuello, G B. Sharrock

The Prince Lyell orebody at Mount Lyell Mine has a rich mining history commencing with the open pit in 1935, which transitioned underground in 1972. Between 1972 and 2014 a total of 64 Mt was mined underground as the mine extended from 210 m to 1100 m below surface. As the depth increased, three separate transitions in the mining method occurred to meet the changing geotechnical conditions, ore grade, mining costs and metal prices. The first was open stoping with pillar recovery in 1972, followed by front caving and longitudinal sublevel caving (1995), and finally transverse sublevel caving (2004 to 2014). This paper provides an overview of key geotechnical and planning milestones relating to the evolution of the mining method including underground stability, gravity flow, cavability and subsidence. Key aspects of the mine design, geotechnical parameters and rock mass response are described and critiqued with reference to observational, numerical and empirical methods.CITATION:Sharrock, G B and Cuello, D A, 2016. Geotechnical milestones at Mount Lyell Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 427–438 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By W. A. Naismith

On 16 July 2004, at 07:10 a collapse of about 1.8 million m3 (about 4 ½ million tons) took place on the north wall on Nchanga Open Pit. This collapse was the result of a developing instability that was first identified when the benches in this area were exposed during September 2002. The NOP geotechnical and survey departments closely monitored the development of the failure. Control measures were implemented to reduce risk to men and equipment. These measures were continually improved and adjusted in reaction to observations and changing conditions. The purpose of this paper is to describe in detail the monitoring results that were obtained both by traditional methods and the novel slope stability radar system (SSR). Difficulties encountered in establishing critical deformation levels and deformation rates that can be used to predict the onset of collapse are described. Details of the monitoring and control measures, which led to the successful completion of mining in the area, are also described in this paper.

Jan 1, 2005