Search Documents

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

By S. M. Spottiswoode

Much as one hopes to predict whether damaging seismicity might occur somewhere in the next shift, this is not possible at present. Recently, an analysis of seismicity at two mines has shown that a small increase in seismicity occasionally occurs before both large and small events. This analysis is extended here to five mines, with the same results. Earthquake seismologists forecast hazard in terms of the average incidence of earthquakes over the last 50 years, adjusted on an hourly basis according to the possibility of aftershocks of events that have happened. The rate of seismicity in any area remains approximately constant when expressed as seismicity per area mined, or better still, per unit of elastic strain energy released. It is suggested that seismic hazard in mines be estimated using historical seismicity and forward modelling, adjusted according to the possibility of aftershocks. In summary, medium-term forecasting of seismicity is viable; short-term prediction of large events is not.

Jan 1, 2010

By Ron Frye, Carl Liibbe, Wayne Curtis, Julie Pecori, Dan Leach

Test work comparing the performance of a Low Density Porous Ammonium Nitrate Prill to regular Porous Ammonium Nitrate conducted in Pennsylvania and New York showed that less ammonium nitrate was required to perform the same work and that improved sensitization of an emulsion/ammonium nitrate blend reduced “orange fumes”. Fragmentation was similar in all tests with improved heave and throw experienced.

Jan 1, 1997

By Verya Nasri, Mehdi Bakhshi

"Fiber reinforcement has emerged as an alternative to steel bars in precast concrete segments due to advantages such as saving cost and reducing production time while developing a more robust product with improved handling and long-term durability. ACI recently drafted a new report as the first design guideline on FRC tunnel segments to provide specific guidance for this emerging technology. ACI document offers general information on the history of FRC precast segments from tunneling projects throughout the world; a procedure for structural analysis and design based on governing load cases, and a description of the material parameters, tests and analyses required to complete the design. This paper summarizes the design considerations in this ACI guideline prepared by the authors of this paper as the main contributors. Application of this guideline to design of a tunnel with an internal diameter of 5.5 m (18 ft) results in elimination of steel bars.INTRODUCTIONPrecast concrete segments are installed to support the tunnel excavation behind the Tunnel Boring Machine (TBM) in soft ground and weak rock applications. The TBM advances by thrusting off the completed rings of precast concrete segments that provide both the initial and final ground support as part of a one-pass lining system. These segments are typically designed to resist the permanent loads from the ground and groundwater as well as the temporary loads from production, transportation and construction. Tunnel segments are generally reinforced to resist the tensile stresses at both the Serviceability (SLS) and the Ultimate Limit States (ULS). With traditional rebar, a significant amount of labor is needed to assemble the cages and place the rebar, which results in higher production costs.Fiber Reinforced Concrete (FRC) can be used to enhance the production, handling, and placement of precast concrete segments. This is because of the uniform dispersion of fibers throughout the segment to include the concrete cover, which is very advantageous for resisting the bursting and spalling stresses. These stresses develop as a result of the high loads induced on the segments during the TBM jacking process. The presence of fiber in the concrete matrix helps mitigate against unintentional impact loads during segment handling and tunnel construction operations."

Jan 1, 2016

By L Matthews, D O’Dea, P C Hayes, J Manuel, B Monaghan, T Honeyands, D Pinson, J Leedham

Many different approaches have been used in the past to characterise iron ore sinter mineralogy to predict sinter quality and elucidate the impacts of iron ore characteristics and process variables on the mechanisms of sintering. Characterisation techniques include optical image analysis and point counting, X-ray diffraction and scanning electron microscopy. Each technique has its advantages and disadvantages depending on the objectives of the measurement. It is generally acknowledged that silicoferrite of calcium and aluminium (SFCA) is very important to the quality of the sinter produced; however, strict definitions of the phases and textures of SFCA are not generally agreed. This paper summarises the state-of-the-art in sinter characterisation applied in Australia by both academics and industrial researchers. The results from various techniques are compared and the relationships between the measurement results are discussed.CITATION:Honeyands, T, Manuel, J, Matthews, L, O’Dea, D, Pinson, D, Leedham, J, Monaghan, B, Li, H, Chen, J, Hayes, P C, Donskoi, E and Pownceby, M I, 2017. Characterising the mineralogy of iron ore sinters – state-of-the-art in Australia, in Proceedings Iron Ore 2017, pp 49–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Steve Kral

Improved metals and other commodity prices have caused the mining industry to open new mines, re-evaluate development opportunities at potential mines and increase production at existing ones. This sense of renewed optimism is being seen at operations and development projects around the world. Except in the United States. The regulatory structure there has not allowed the domestic industry to share much in mining’s resurgence. It can still take up to 10 years to permit a new mine. And, while Clinton-era regulations regarding mill sites have been put on hold, existing mines that wish to expand operations still face significant regulatory and environmental hurdles. But things may begin to improve in the United States.

Jan 1, 2005

By L. Nahai

Overall mineral industry productive activity in Europe increased in 1965, following general upward trends in gross national product and total industrial production4 recorded. The gross national product of non-Communist Europe in market prices in 1965 was estimated at $572 billion and that of Communist Europe at $409 billion. However, the extractive sectors of the mineral industries generally did not fare as well as the processing sectors. In fact, a number of countries recorded lower production levels in this sector in 1965 than in 1964 and most countries had a lower growth rate in extractive industry output than in overall industrial output. Among the non-Communist nations of Europe, a general decline in coal production and lower levels of iron ore output in France, West Germany, and Luxembourg contributed significantly to the smaller growth rates or declines in extractive indexes. Where higher indexes were registered, this generally resulted from the performance of the petroleum and natural gas industry; exceptions were Greece, Norway, and Sweden. The decline recorded for Czechoslovakia was attributable entirely to poorer performance by that nation's coal industry.

Jan 1, 1967

By W. B. Xie

The hardening behaviour and microstructure evolution of Cu-30Ni-30Mn alloys aged at 350 °C has been investigated utilizing optical microscope, scanning electron microscope, transmission electron microscopy and Vickers hardness tester. The results show that the discontinuous precipitation of NiMn phase results in a remarkably hardening effect in Cu-30Ni-30Mn alloy during aging at 350 °C. The maximum hardness (~494HV) is attained in the sample after aged for 48 h. The NiMn precipitates are ordered and have a face-centered tetragonal structure. The coherent orientation relationship between the NiMn precipitates and Cu matrix is (220)Matrix // (220)P, [1-1-2]Matrix // [1-1-2]P. In addition, there is a linear relationship between hardness and volume fraction of the discontinuous precipitation, which indicates that the hardness increment of Cu-Ni-Mn alloys aged at 350 °C is attributed to the microstructure characteristics of discontinuous precipitation. The high strength of discontinuous precipitation colony is caused by the formation of nanoscale NiMn precipitates with a lamellar structure in discontinuous precipitation. INTRODUCTION Cu-Ni-Mn alloys are attractive candidates for oil drilling, aerospace and energy applications due to their high elasticity, high strength and excellent corrosion resistance (Sun et al., 2009; Liu, Yang, Xia, Jiang, & Gui, 2016). The high strength of the Cu-Ni-Mn alloys is mainly attributed to the precipitation of NiMn phase (Shapiro, Tyler, & Lanam, 1974; Xie et al., 2015). The uniformly dispersed nanoprecipitates formed by continuous precipitation can impede dislocation movement, and thereby lead to a significant improvement in strength of traditional precipitation-strengthened alloys. However, it is reported that there are two precipitation types observed in Cu-Ni-Mn alloys, namely, continuous precipitation and discontinuous precipitation (Shapiro et al., 1974). The discontinuous cellular colony with a lamellar structure nucleates at grain boundaries, and progressively grows inward the grain on the process of discontinuous precipitation (Ng, Bettles, & Muddle, 2011). It is found that the discontinuous precipitation can occur in many Cu-based alloys, such as Cu-Ni- Mn alloy (Shapiro et al., 1974), Cu-Be alloy (Monzen, Hasegawa, & Watanabe, 2010) and Cu-Ni-Sn alloy (Zhao, & Notis, 1998). Many studies consider that the discontinuous precipitation results in a detrimental effect on hardness and strength, and the discontinuous precipitation occurring during aging treatment should be suppressed (Markandeya, Nagarjuna, & Sarma, 2004; Semboshi, Sato, Iwase, & Takasugi, 2016). The mechanical properties can also be improved by discontinuous precipitation in AZ91 magnesium alloy (Tamura, Kida, Suzuki, & Soda, 2009) and AM30 magnesium alloy (Saikawa et al., 2012). Jun (2017) found that the reduced interlamellar spacing of precipitate fibers in discontinuous cellular colony leads to a significant increase in hardness. Indeed, the strengthening contribution of discontinuous precipitation is similar to that of continuous precipitation in Cu-20Ni-20Mn alloy. Discontinuous precipitation of NiMn phase can provide a significant strengthening effect in Cu-Ni-Mn alloys.

Jan 1, 2019

The present work is mainly focused on developing intermetallic inert anodes for aluminum electrolysis. The anode alloy based on Al-Ti-Cu system was prepared by casting, followed by the application of a protective coating. Behaviour of corrosion and the passivation under anodic condition was characterized using the electrochemical and microscopic techniques. The results obtained clearly demonstrate that the oxide coating can provide good corrosion resistance via surface passivation of alloy anodes, rendering them inert in cryolite melt.

Jan 1, 2006

By Madan M. Singh

With the current emphasis on ecology, safety, and conservation of natural resources, some consideration should be given to methods of mining that reduce surface damage, make the mining of coal less hazardous, and allow exploitation of a larger percentage of the coal in situ. One method that can be helpful toward attaining these objectives is the use of packing or stowing. Stowing involves the replacement of the ore that has been removed by waste material obtained from within the mine or elsewhere. Evidently, it would be most beneficial if this waste for packing were available from the mine being worked, but generally this is not possible. If complete stowing is adopted, it is necessary to bring in packing material from other sources. Stowing tends to reduce surface subsidence, but not eliminate it. It enhances roof support and curtails accumulation of methane in the gob, making the mining operations safer. It may also allow one to obtain a larger amount of coal. Currently, in the United States, a substantial amount of coal is left in place as pillars, in the hope that it will support the overburden indefinitely. Some of these could be extracted with stowing. The mining of thick, steep, or contiguous seams would also be facilitated.

Jan 1, 1974

By Samantha Whisman, James R. Hein

Hydrothermal marine manganese-oxide deposits (HMMD) are cemented and variously replaced volcaniclastic and biogenic sediments that were mineralized by distal, low- temperature, hydrothermal fluids. HMMD predominantly form below the seabed as sediment-hosted statabound deposits but can also form on the seabed. These deposits form at oceanic and back-arc basin spreading centers, volcanic arcs, and mid-place hotspot volcanoes. HMMD have traditionally not been considered to have an economic potential because they were considered to be devoid of economically valuable critical elements. This contrasts with their non-hydrothermal counterparts, ferromanganese crusts and nodules, which are enriched in many critical elements. However, manganese is now one of the critical metals and HMMD have the highest manganese contents (up to 55% Mn, so- called battery-grade Mn) of all the types of deep-ocean mineral deposits. There is a growing demand for this critical metal and an upward trend exists in the price of manganese on the global market. Also, other critical elements can occur in high concentrations in some HMMD and their economic potential has not been considered, especially for lithium (up to 0.17%) and molybdenum (up to 0.24%), but also vanadium (to 820 ppm), chromium (to 346 ppm), and nickel (to 0.45%), among others. Which of these critical elements are enriched and their concentrations depend on the types of rocks leached at depth by the hydrothermal fluids, the composition of hydrothermal minerals precipitated in the higher temperature parts of the circulation system, and the types of sediments mineralized by the manganese oxides. For example, mineralization of a carbonate sediment resulted in the highest lithium contents, whereas leaching of ultramafic rocks at depth as a rule results in the highest chromium and nickel contents in the HMMD. These deposits are known to be widespread, especially in volcanic arcs, but their lateral and vertical extents and consequently size, tonnage, and grade have not been determined. Most samples of hydrothermal deposits have been collected by dredging and therefore the in situ relationships often are not known. One sample from the Mariana volcanic arc, west Pacific, was collected by ROV at 1274 m water depth from a layered outcrop 6.6 m thick that may be a sequence of pervasively mineralized volcaniclastic layers and offers the first clue as to the potential vertical extent that these deposits may attain. However, only the top ~0.4 m-thick layer was sampled, so it is not known whether the mineralization extents throughout the outcrop. Although large manganese deposits of various origins occur on the continents, they consist of manganese carbonates, silicates, or complex mixtures of manganese minerals. In contrast, marine hydrothermal HMMD exhibit relatively simple mineralogy that would make processing of this potential ore much simpler.

Jan 1, 2018

By L. Holappa

Ferroalloy production is an energy-intensive industrial sector with significant CO2 emissions. In this paper the current situation in ferroalloy processes is discussed from the standpoint of global environmental issues, trends and development. Progress and data of ferroalloys production are frequently compared with the steel industry, which is a closely related sector and the main user of ferroalloys. Emission factors of processes and electricity production are examined as well as possibilities and future scenarios of how to diminish CO2 emissions. As a part of this study a questionnaire was submitted to experts in the field of ferroalloys worldwide to survey opinions on the ferroalloy industry today and in the near future (2020). Eighteen questions concerning raw materials, energy, environmental aspects, by-products and economic aspects were responded to by seventeen experts, the answers were analysed and conclusions were drawn. Keywords Ferroalloys, energy, CO2 emissions, electricity, sustainability, questionnaire.

Jan 1, 2010

By T. A. Grammatikopoulos, B. Vasily, A. H. Clark

"The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoeshaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York, no carbonate protolith is preserved, and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560°C, or, alternatively, 550 MPa and ca. 630°C.Several high-grade zones, averaging >40% but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 cm to 5 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates.St. Lawrence compares favourably to other known prospects and operating wollastonite deposits: having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production."

Jan 1, 2003

By Patrick D. McLaughlin

Crater blasting techniques have had relatively little application in the surface mining industry. This is not surprising, considering the geometry required to efficiently use cratering. The more widely known blasting operations that employ some form of cratering are listed below.

Jan 1, 1992

By M. F. Vancas

The San Manuel oxide ore reserve ranges in depth from being exposed on the surface to lying 1000 ft. beneath a conglomerate layer all of which is confined in the subsidence zone of an active sulfide block caving operation. Present day recovery of the oxide copper values is either by open pit mining-dump leaching, or in-situ leaching of the oxide ore using dilute sulfuric acid solutions and solvent extraction/electrowinning processing of the pregnant leach solutions. Future plans are for continuation of leaching with expansion of reserves and increased processing rates. The state of the mining industry and copper in particular has not been good for a number of years. All of the producers that are still operating have made major adjustments in order to remain competitive. Magma Copper Co. is no exception.

Jan 1, 1987

By A. Vien, A. J. Neale, B. C. Flintoff, R. P. Edwards

Froth flotation is one of the most widely used and effective processes for mineral beneficiation. First introduced in 1911, flotation technology has seen many developments over the past 80+ years. Innovations in reagent chemistry, equipment design, process analysis and process control have given design and plant engineers a powerful set of "tools" for process optimization. However, it does not follow that all flotation systems are optimized. As Klimpel observes: "The problem with the industrial flotation process is that it is relatively easy to get reasonable results, and relatively difficult to get excellent results" Klimpel (I 988). While reasonable was sufficient in the past, competitive forces will make excellent necessary in the future. Judging by the activities in many Canadian plants this transition is already underway. This paper examines the role of some of the optimization "tools" in effecting this change.

Jan 1, 1994

By J. T. Shimmin

THE past twenty-five years has been a period of unparalleled improvement in all lines of mining and metallurgical equipment, but probably none has undergone greater refinement and development than the vacuum filter. Beginning a quarter of a century ago, there has been steady advancement in the art of vacu-um filtration until today its use has become virtually standard practice for dewatering throughout the entire metallurgical industry as well as in important parts of the chemical and industrial processing fields. The credit for the first successful application of vacuum filtration &apos;at the Consolidated Mercury mines in Utah in 1902 undoubtedly belongs to George Moore. There, it is said, his filter reduced the loss of gold in the slime and sand from $1.25 to 40c. per ton. Successful applications were subsequently made by Mr. Moore at the Liberty Bell mines, Telluride, Colo., the Lundberg, Dorr &Wilson mill at Terry, S. D., and elsewhere. E. L. Oliver is generally credited with, having done the most to work out the necessary continuity of op-eration exemplified in the well-known continuous vacu-um filter which bears his name. Others made improve-ments also, but in my opinion all the new ideas advanced in recent years are modifications of the fundamental principles originated by the two pioneers, Moore and Oliver. Considerable interest has been shown recently in the new type of continuous internal-type vacuum filter which is associated with my own name1. In response to frequent inquiries regarding it and the steps which led up to its invention, I am giving herewith a brief account of the early history of this development and some of the more important installations which have been made during the last year or so. A. M. Nicholas (now deceased), an Australian engi-neer, conceived the idea, several years ago, of manu-facturing a continuous vacuum filter with the filter medium applied upon the inside of the drum, as con-trasted with existing drum filters in which the medium is applied externally. Nicholas recognized that a ma-chine of this type would be simpler than one with a tank and would overcome some of the difficulties en-countered with tank filters on certain classes of pulps, and he appreciated the value of having filtration take place in the same direction as the gravitational settle-ment of the solid particles in the pulp, the pulp being retained within the drum instead of being held against the outside surface. The ease of starting up after a shut down was likewise realized by Nicholas. It was tried in the United States, but was not entirely success-ful primarily due to mechanical defects.

Jan 5, 1928

The re-use of waste water from coal preparation plant tailings is always desirable, but is generally problematic in terms of solid-liquid separation. Dewatering and disposal of coal slurry at a high percentage of moisture poses a major technological and environmental challenge to mining and mineral processing industries world-wide. Characterization and flocculation of these coal tailings reveals that the separation of fine coal tailings depends on factors such as size distribution, slurry viscosity, zeta potential, pulp density, circuit design, plant operating parameters, and the behaviour of solid particles in an aqueous medium. The present study was carried out on -600 mm coal tailings collected from a coking coal preparation plant of Jharia Coalfield, India, using anionic flocculent. Characterization studies revealed that the zeta potential was highest (-44 mV) at a pH of 9.0, the size range of the particles was 1.1?700 m, and the average ash content was 62.57%. Flocculation studies were performed at different solid concentrations, pH values, and polymer dosages. The results indicated an efficient settling rate of 178.15 mm/min at 8% solid (w/w) at a flocculent dosage of 32.50 g/t solid. The turbidity of the clear liquid obtained was 7.42 NTU.

Jan 1, 2014

By O. C. Blade

"An important function of the Bureau of Mines is promoting the conservation and more efficient utilization of a natural resource. Petroleum is such a resource, and its utilization depends to a considerable degree upon its characteristics. For this reason the Bureau of Mines, over a period of years, has analyzed many samples of crude petroleum by the Bureau of Mines Hempel method 3/ and published complications of crude-oil analyses. Among such publi¬cations are several reports presenting analyses of crude oils from fields in Oklahoma. The most recent of these relates to samples from southern Oklahoma. 4/ The present paper provides additional analyses of Oklahoma crude oils, largely from areas and formations not heretofore represented in published reports. The analyses of 248 samples from 153 fields are presented individually and collectively in the tables of this report.Crude oil has been produced in Oklahoma in commercial quantities since 1891, and peak production was reached in 1947. The State's cumulative production to January 1, 1944, is, according to the American institute of Mining and Metallurgical Engineers, 5,186,466,000 barrels. 5/ The annual production of crude petroleum in Oklahoma for each year from 1891 to 1943, inclusive, is given in table 1."

May 1, 1945

By Ogden Malin

IN conducting the manufacture of extruded brass rods and brass forgings it has been noticed that there is considerable variation in the physical properties, particularly the machinability of different rods and forgings, even though the composition, working temperatures and method of manufacture remain the same. It is the purpose of this paper to attempt to establish the cause and extent of this variation, and also to determine whether variations in composition within certain defined limits influence hardness and machinability to any marked degree. The writer believes that this variation probably is due to the variation in grain size of the metal, therefore the microstructure of several compositions under various conditions of working were examined in an effort to establish this as a fact.

Jan 1, 1932