Search Documents

By T. P. Meloy

Like our wives, the comminution of brittle solids is easy to recognize but difficult to describe. However, describing it we must. Describing the fracture mechanism of brittle solids permits the eventual mathematical quantification of the results, process optimization and control strategies. This paper presents a physical model of brittle solid comminution that explains why the slope of the log-log size distribution curves have a slope of one or less in the smaller particle sizes. To develop the hypothesis, modifications of the Gaudin Meloy physical model are made. In brittle solids, comminution takes place by cracks propagating through the material. These cracks may bifurcate as they move. Cracks may terminate either on the original surface of the material, or on a secondary crack within the material formed earlier in the comminution process.

Jan 1, 1994

By Paul Soros

The cost of shipping British coal by water to domestic and ex- port users has been expensive. The traditional transportation system functioned as follows: coal in up to 50 different grades was accumulated in railway cars at several loading ports; on the arrival of a vessel, cars were dumped in the desired order to produce the required blend. It was a direct rail- road-to-water interface. Railroad freight was high because of the poor utilization of the large number of small (14, 18 or maximum 28-ton capacity) hopper cars required. Ocean freight was high because the ships were small, mostly on the order of 1500-3000 dwt and even these took a long time to load. Assembling and loading larger cargo presented a challenge in logistics to the ports, the railways and the coal washeries. The accommodation of larger bulk carriers was hampered by a tidal range of up to 24 ft which led to the development of impounded harbors, with locks that limit the size of vessels.

Jan 12, 1973

By Dennis Wrixon

It was a little bit exceeded. The decision was the uniform settlement is measured at each one corner and the highest one corner is the important one. And in addition there is a differential settlement of 2.1 mm allowed. So we reached about 7.8 or 7.9 mm with the highest corner and in addition 2.1 so it was a little too much. But behind there is a very difficult calculation of the authorities where all of the displacements are combined together and there are of course some more factors of safety in these settlements.

Feb 10, 2003

By N. Kumar Kittusamy

By J. E. Gill, A. R. Byers

"The property of Sladen Malartic Mines, Limited, is in the northern half of Fourniere township, Abitibi county, Quebec. The group is large, but the part so far found to be of economic interest is a strip 3,200 feet long between the Canadian Malartic property to the west and the East Malartic and National Malartic properties to the east ( Fig. 1).The original claims were staked in 1923 and 1924 by St. B. Sladen and H. S. Kennedy because gold was known to occur on claims nearby. In 1928, detailed mapping of the Malartic Gold Mines property (now Canadian Malartic) showed the presence of an east-west gold-bearing zone traceable almost to the Sladen boundary. During the winter of 1929, a hand-driven drill was used to secure short sections of core through casing pipe sunk to bed-rock. This proved the existence of the main Sladen ore zone, but it was not until the price of gold was increased, in 1934, that serious work was attempted.Underground work was started in 1935 and milling in January, 1938. To the end of 1945, 168,882 oz. of gold were recovered from 1,641,974 tons of ore, an average of 0.103 oz. a ton.GEOLOGYThe bed-rock underlying' the Sladen Malartic property consists mainly of Precambrian greywacke and volcanics that appear to form a conformable series with a general northwest strike and vertical to steep northerly dip. Except where disturbed locally by drag folds or faults, tops face north. Intrusive rocks that range in composition from diorite to granite cut the sediments and volcanics. The basic types, generally quartz diorite and diorite, form dykes or sills in the volcanic rocks. The more acidic types, mainly quartz syenite and related porphyries, intrude the volcanics and the sediments in the form of dykes, sills, and larger, stock-like bodies.The orebodies are parts of slightly shattered or brecciated zones, mainly in greywacke, but partly in syenite, diorite, and volcanics, that have been more or less replaced by fine-grained quartz, pyrite, and minor amounts of sphalerite, galena, sylvanite, petzite, and gold."

Jan 1, 1954

One of the newest and most modern surface mining operations in the East is gathering steam at Mapco Inc.'s Martiki mine in anticipation of yielding 2.7 million tons (3 million st) of coal annually.

Jan 10, 1977

The influence of varying amounts of magnesia, silica, and alumina in iron ore sinter on its mineralogy, reducibility index (RI), reduction disintegration index (RDI), physical breakdown (AI and TI), and production properties (coke breeze rate) were examined. It was found that the mineralogy of iron sinter can more easily be predicted from its chemical composition than from the RI, RDI, AI or TI. Anticipating the consequence that varying amounts of MgO and SiO2would have on sinter properties is complex, and not necessarily predictable. High concentrations of Al2O3in the sinter result in high concentrations of the SFCA phase, but with drastically deteriorated properties. This study also confirmed that the form in which fluxes are added to the raw material sinter mixture affects the mineralogy and properties of the produced sinter.

Jan 1, 2010

By AIME AIME

COUNCIL. PRESIDENT OF THE COUNCIL. CHARLES KIRCHHOFF NEW YORK, N. Y. (Term expires February, 1912.) VICE-PRESIDENTS OF THE COUNCIL. BENJAMIN B. LAWRENCE NEW YORK, N. Y. JOSEPH W. RICHARDS SOUTH BETHLEHEM, PA. ALBERT SAUVEUR CAMBRIDGE, MASS. (Term expires February, 1912.) B. CHRISTY BERKELEY, CAL. W. A. LATHROP PHILADELPHIA, PA. GARDNER F. WILLIAMS WASHINGTON, D. C. (Term expires February, 1913.)

Sep 1, 1911

Caving of the second lift of the E26 orebody at Northparkes Mines was monitored with a comprehensive package of instrumentation, including an ISS seismic monitoring system. Seismicity was collected by an array of 19 triaxial accelerometers and 9 uniaxial geophones, giving a high quality seismic data set. The seismic response to block caving at Northparkes has been divided into two papers. The first paper focuses on the seismicity during undercutting. The second paper deals primarily with the seismicity during cave propagation during initial cave production. In this paper, traditional seismic monitoring concepts are applied to seismicity during cave mining. More than 40 000 seismic events were recorded during cave undercutting between February and January 2004. Events up to local magnitude +1.3 were recorded near the mine during undercutting, with event rates of up to 500 per day. Analysis of frequency-magnitude distributions, S-wave to P-wave energy, and temporal variations in event magnitude all gave insight into the seismicity recorded. In addition, a new technique, called apparent stress time history, was shown to be sensitive to stress change from undercut blasting, and useful to identify significant periods during cave development. A significant difference was identified between the cave back location and the halo of seismic events above the cave. Throughout the undercutting, the a seismic zone of loosening was typically 50 to 70 metres in vertical thickness. Based on the seismicity, a stress driven rock mass failure model is proposed. Early in the undercutting, seismicity and movements in the seismogenic zone were directly triggered by stress change from undercutting. Towards the end of undercutting, seismicity was virtually uncorrelated with undercut blasting, and likely due to the onset of cave initiation.

Jan 1, 2008

By W. P. Corking

"The purpose of this paper is to describe the relationship of the goldbearing ore to structure at the Pickle Crow mfoe. Information beyond this scope may be found in the reports and papers of Hurst( l), Bothwell(2), Thomson(3) , and Monette( 4).The property lies on Crow river, in Patricia district, 80 miles northeast of Allanwater, and about 125 miles northeast of Sioux Lookout on the Canadian National railway. From April of 1935, when the mill began operation, to the end of 1944, a total of 564,890 oz. gold and 49,275 oz. silver were recovered from 958,416 tons of ore.Mining on the property is at present carried on in two separate orebodies, the Howell and the No. 2 vein. Stoping has been carried on from every level on the Howell vein to a depth ot 2,450 feet below the surface and from several levels on the No. 2 vein through a mile long cross-cut on the 750-foot level to the Howell vein workings. A steadily increasing volume of ore is being obtained from the No. 2 vein.Each of the two orebodies consists of vein quartz with small amounts of other gangue minerals either in a single vein or a stockwork of veins. Both lie within sheared walls and carry gold in the free state. Fig. 1 shows the position of the veins with respect to the surrounding rocks. It will be noted that the delineation of the beds of iron formation shows that the lava flows and minor, interbedded sediments that make up most of the country rocks are areally folded and contorted.STRUCTURENearly all gold found to date in sufficient quantity and concentration to make ore in the Pickle Crow area is confined to these major quartz veins . Both strike a little north of east and dip north, and in both cases the attitude of the enclosing rocks is somewhat more north of east in strike and more steeply north in dip than that of the veins. As a result of this disposition both veins migrate across their enclosing rocks at a moderate angle in both dip and strike. (In this connection it should be noted that No. 2 vein dips at a considerably flatter angle than its host rock, but has a very pronounced rake to the northeast, effecting the same result as in the Howell vein.)"

Jan 1, 1954

The slags produced by the Imperial Smelting Process (ISP) are based on the system ZnO-?FeO?-Al2O3-CaO-SiO2. The slag chemistry is important to the process since it determines the fluxing practice and the operating temperature of the furnace required to produce fluid slag. The paper presents the results of the first systematic experimental investigation of these ZnO-containing slags in equilibrium with metallic iron, and provides information on the primary phase fields and liquidus temperatures in these slags over the range of compositions used in ISP practice. A feature of the slags is the presence of alumina, which has a major influence instabilizing the spinel phase. This information presented in the form of pseudo-ternary sections ZnO-?FeO?-(Al2O3+CaO+SiO2) enabling the data to be readily used by plant engineers. Keywords: liquidus temperature, ISP, EPMA, ZnO-?FeO?-Al2O3-CaO-SiO2, phase equilibria.

Jan 1, 2004

By Richard Curtis

Optimum Colliery is presently experiencing a shortfall of stripping capacity in order to meet its production requirements. Due to the long dragline procurement times, several alternative stripping methods were evaluated in order to alleviate this shortfall in the interim period. Based on the experience gained at the mine. The writer will discuss some of the important factors which influence dragline performance and show how these factors may by used in a theoretical approach to analyse various dragline applications.

Jan 1, 1990

By Leonard Greenburg

The analytical procedure necessary when using this new impinger•bubbler eil)paratus is almost identical with that em:r;,loyed with the Palm0r a:pp8.ratua. As sugar is not employei, the new apparatus por.;sesses the advantage over the eug.r tube method in having vsry low control errors, being, therefore, much simple in laboratory manipulation during analysis.

Aug 1, 1922

By D. Tao

More than 80 million metric tons of fly ash is produced annually in the U.S. as coal combustion by-product. Fly ash can be converted to value-added products if unburned carbon is reduced to less than 2.5%. However, most of fly ash is currently landfilled as waste due to lack of efficient purification technologies to separate unburned carbon from fly ash. A rotary triboelectrostatic separator has been developed and patented recently at the University of Kentucky with unique features. Several fly ash samples have been used to understand the effects of major process parameters on the separation performance. The results show that compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator has significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range. Key words: Coal, Combustion Waste; Fly Ash; Particle charging; Separation.

Jan 1, 2008

By John C. Schneider

During the past decade, operators and researchers have worked toward a better understanding of the mechanisms operating in flotation. As reported by W. J. Trahar in 1981, this work commenced with the operators determining a relationship between recovery and particle size. They defined three particle size ranges, that being fine, intermediate and coarse. It was noted that the fine and the coarse ranges had slower flotation rates than the intermediate range as demonstrated by their lower recoveries.

Jan 1, 1998

By CHARLES F. RAND

PRESIDENT CHARLES F. RAND,1 NEW YORK, N. Y. PAST PRESIDENTS CHARLES KIRCHHOFF,1 NEW YORK, N. Y. JAMES F. KEMP,2 NEW YORK, N.. Y. FIRST VICE-PRESIDENT BENJAMIN B. THAYER,1 NEW YORK, N. Y. TREASURER GEORGE C. STONE,1 NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER. W. RAYMOND, NEW. YORK; N. Y. SECRETARY BRADLEY- STOUGHTON NEW YORK, N. Y.

Jan 2, 1914

By Frank Rausche

Introduction and Background Testing -Pile Preparation -Data Processing -Data Interpretation/Case Studies Case Studies - Existing Piles Stories from around the world

Jan 1, 2001

By L. Lewczuk

A detailed mineralogical and liberation study was performed on the iron ore mill products from the Scully concentrator of Wabush Mines, Newfoundland. Automated image analysis techniques were applied to deter-mine grain size distribution and liberation of all mineral components of the ore. As a result of the study it was indicated that iron recovery can be improved and the Mn minerals reduced in the iron ore concentrate by (a) increasing spiral middlings, (b) regrinding the middlings, and (c) separating the Mn minerals from the iron minerals in the reground middlings.

Jan 1, 1988

By E Rubio

El imaginario común sobre la construcción de la minería a cielo abierto es que requiere de equipos pesados para obtener mayores producciones. Sin embargo, la aplicación de este método en los minados de vetas de plata en las minas de Julcani de la Compañía de Minas Buenaventura, resultó de gran aporte. En ese sentido, el presente trabajo describe el proceso técnico de este método de explotación en esta producción de plata, asi como señala los beneficios económicos para la pequeña y mediana minería.

Nov 20, 1972

By R. B. Yerxa, C. F. Green, H. O. Hofman

MASSACHUSETTS INSTITUTE OF TECHNOLOGY, In refining copper, the metal is melted down in a reverbera tory furnace in a more or less oxidizing atmosphere and then further subjected to an oxidizing smelting in order to eliminate the common impurities, most of which have a stronger affinity for oxygen than has copper. In these operations some of the copper is oxidized to cuprous oxide and dissolved by the metal bath. When the quantity of dissolved cuprous oxide has reached about 6 per cent, the metal is said to have been brought to " set-copper." A button-sample will show a depressed surface and, when broken, a single bubble at the apex of the depression; the fracture will be brick-red and dull. It is essential to carry the oxidation to this point in order to know that the impurities have been oxidized as far as it is possible under the given working-conditions. Nearly all the cuprous oxide of the set-copper is now reduced to the metallic state by poling, when "tough-pitch" copper will be obtained. A button-sample will show a flat surface. Upon breaking, it will be found that the former bubble has disappeared and that the fracture has become rose-colored and shows a silky luster. The quantity of cuprous oxide allowed to remain in the copper will vary with the impurities still present in the metal and with the degree of pitch that it is desired to reach. It is essential for the general physical and the mechanical properties of the resulting copper that such impurities as arsenic, antimony, bismuth, lead shall be present in the oxidized state, as they are

Jan 1, 1904