Search Documents

By Thomas M. Barczak

Wood cribs are used extensively to stabilize mine openings by providing resistance to deflections of the immediate roof and floor and by supporting the weight of unstable rock masses. While the unit costs of these supports are relatively low, their extensive use results in significant costs to coal mining. The Bureau of Mines has developed a model that computes the load capacity of wood cribs as a function of the displacement of the crib structure induced by mine roof and floor convergence. This permits comparison of the loading characteristics of various crib constructions and enables systems to be designed with consideration of the load conditions imposed by the mine environment. The design method matches the stiffness, strength, and stability of the crib structure with expected rock mass behavior to determine a crib design and employment spacing that will provide the lowest cost support.

Jan 1, 1993

By P. S. Piper

In the 1960s it was suggested that the volume of stope convergence, and hence the rockburst hazard, could be reduced by the emplacement of backfill. Recent advances have facilitated the placement of large quantities of backfill underground, and a reassessment of its potential benefits as part of a regional support strategy is now timely. In this paper the principal criteria of effectiveness of backfill are taken to be its impact on face energy release rate (ERR) and average pillar stress (APS) levels, and maximization of acceptable ore extraction ratios. The possible effects of backfill on excess shear stresses (thought to modulate large seismic events) are also briefly reviewed. Analytic solutions describing backfill properties and their impact on ERR and APS in certain idealized geometries are also presented, and compared with the results of an extensive suite of computer simulations, in which parameter sensitivities are explored. Results indicate that a regional support strategy is required at depths exceeding 2 km in order to maintain acceptable levels of ERR, and backfill ribs can on their own fulfil this role at depths less than 3,3 km. At greater depths use of stabilizing pillars becomes imperative, but here too supplementary backfill ribs can reduce ERR and APS levels and permit significant increases in ore extraction ratios.

Jan 1, 1988

By Stavros A. Argyropoulos, Radhakrishna Valiveti, Bernard Closset

"The use of microprocessors in metallurgy is currently increasing at a very fast rate. A large number of companies are offering systems ""off the shelf"" which are aimed at the data acquisition and process control market. There are two main drawbacks to these systems: first, they are usually quite expensive, and second, they are not completely compatible with the target metallurgical application. An alternative is to develop a microcomputer-based system "" in lab "".A dedicated microcomputer system has proved to be very useful in many metallurgical research applications(1,2)). However, in this system the analog input signals had to be transferred over long distances , and significant noise was introduced despite the use of shielded cables. In order to overcome this problem a network of low pass-filter s was designed and built. The usage of the abovementioned system brought the need to digitize the analog signals in-situ and transfer the digital signals, which are much less susceptible to noise over very long distances. This distinctly different design philosophy has become a reality with the evolution of microprocessor technology over the last few years. This design philosophy is utilized in this development."

Jan 1, 1984

By R. P. Corbett

Since the beginning of operations at the Kelley mine in 1952, Anaconda has emplaced more than 150,000 cu yd of concrete underground. Concreting practices have changed over the years but the net result is still the same- lower costs along the line and more versatility.

Jan 7, 1961

By Koppe J. C, Dimitrakopoulos R, Costa J. F

Grade control and the delineation of ore/waste in open pit operations is traditionally based on the comparison of estimated grades with an economic cut-off. This paper deals with an alternative approach to grade control based on estimating gra

Jan 1, 1998

By Yoon R-H, Luttrell GH

A theoretical model has been developed to predict the probability of particle collection by air bubbles in a quiescent flotation pulp. The model considers the effects of both hydrodynamic and surface chemistry forces acting during the bubble-particle interaction. Hydrodynamic forces considered include the gravitational, buoyancy, streamline and film thinning resistance forces. The surface chemistry forces considered include the electrostatic, dispersion and hydrophobic forces. The hydrophobic force has been estimated from extended DLVO theory. The model is capable of predicting hydrodynamic and surface chemistry conditions under which bubble-particle adhesion is possible. Validity of the model has been verified experimentally.

Jan 1, 1993

By Morrison R. D, Kojovic T

Industry-sponsored research at the Julius Kruttschnitt Mineral Research Centre has produced models of high tension roll and electrostatic plate separators operating in mineral sands dry plants. The behaviour of mineral species has been characterised under a wide variety of operating conditions by extensive plant machine sampling and laboratory measurements. The effect of operating conditions on separator performance has been quantified by monitoring changes in the weight distribution of mineral species along the product splitter axis. The response of each mineral species has been modelled on a size-by-size basis using an average surface charge decay time and a variation in its surface properties. The models incorporate changes in machine, mineral and ambient conditions on the separation and predict all product flows, assays and size distributions. This paper outlines the structure of the models. These models are being implemented in JKSimSand, an user-friendly simulation software Package.

Jan 1, 1991

By Alan Peacock

Shield supports have been in use in the USA underground mines since 1975, and their development in the intervening time has been progressive and inovative. Specialized techniques are used to optimize their performance in a particular application and to design the component parts.

Jan 1, 1981

Tholeiitic metabasalts comprise at least five geochemically distinct mafic volcanic associations of Late Palaeozoic age within the Gympie Province, southeast Queensland. Geochemical features indicate that parental magmas of the various metavolcanic suites were generated in contrasting tectonic regimes, although each of the suites shows some affinities with eruptives from convergent plate margin settings.Basalts from the Highbury Volcanics of the Gympie Group are island arc tholeiites (IAT) formed during an immature stage of eruptive activity in an intra-oceanic arc. They are unique among the analysed metabasites in possessing high Zr/Nb (Zr/Nb - 30) and very high Ba/Nb, and as well as low Ti/V, Ti/Zr and Ti/Y. These features are explicable solely in terms of contributions from a depleted, convecting upper mantle source, and large ion lithophile element (LILE) enriched fluids ascending from subducted oceanic crust.

Jan 1, 1990

By Sims D. A

This paper primarily describes the application of geology to the different mining methods employed in a large underground mine. The steeply dipping stratiform Silver/Lead/Zinc mineralisation at Mount Isa include up to 28 mineable orebodies. The orebodiea are mined by cut and fill, sublevel benching and sublevel open stoping; the method chosen depending mainly on orebody geomechanics.The sources and methods of data collection, and the interpretation process undertaken, are described. The paper emphasises the different geological input required, by each individual mining method, to provide the necessary production and strata control. This input contributes significantly to the success and efficiency of the operations.

Jan 1, 1990

By Bhattacharyya A. K

A major constraint on sustaining high rates of production in the collieries of the Southern Coalfield of New South Wales is the inability to develop panels fast enough to match the rates of extraction. This inability is particularly crippling in the case of retreat longwall mining and is due to nearly half the time in roadway drivage being spent on strata control operations such as roof support.Increased rates of roadway drivage and significantly improved roadway stability can be achieved by the application of yield pillars between parallel roadways. These pillars are designed to yield immediately upon formation and transfer the damaging roof loads away from the immediate vicinity of the roadways. Since the width of the yield pillar is the key to their successful application, it was determined through the Yield Pillar Experiment conducted by Kembla Coal and Coke Pty Ltd at West Cliff Colliery.Three experimental headings, each nominally 5.5 m wide and 2.8 m high, were driven to form two tapering pillars. The width of these pillars progressively decreased from 24 m to 3 m over a length of 154 m. The convergence between the roof and floor of the headings measured at various cross-sections corresponding to predetermined widths of the pillars are analysed in this paper to evaluate the stability of the tapering pillars at the different widths.The width of the yield pillar in a three heading development layout at West Cliff Colliery was determined to be 7.5 m.

Jan 1, 1995

By Richard Turnbull

Maules Creek mine is an open cut coal near Boggabri in the Gunnedah Basin of New South Wales, Australia. The mine is currently operating at an annualised run rate of 9.5Mt of saleable coal. The plan is to ramp up production to 13Mtpa. Maules Creek has multiple seams each with varying depths; the inter-burden ranges from a few metres thick to greater than 30m (98ft). Due to this, Maules Creek mine is utilising truck shovel operations rather than a cast/dozer push operation.

Jan 1, 2018

By John E. Udd

The stability of a rock mass is influenced by the presence of discontinuities. In assessing stability, it is required that one should know the frictional and cohesive properties of these contained weaknesses. In the study performed by the authors, a number of samples of diamond drill core containing open discontinuities were tested in shear. The results obtained were compared with values which resulted from back analyses of instabilities in the field.

Jan 1, 1979

By Smallnone P, Walker B

Mining of the AKI lamproite pipe at the Argyle Diamond Mine (ADM) commenced in 1985. Originally designed to mine ore at a rate of 3.6 Mt per annum, the project has gone through two major plant expansions to a designed production rate of 8.7 Mt

Jan 1, 1998

By Leahey T. A

The variability of gold mineralization in the Warrego Gold Pod is described by classical statistical techniques using sample distrib- utions and analysis of variance; and by the use of geostatistical variogram analysis to define the spatial variability and anisotropy of the mineralization. Comparison is made between declared mine production from the Nineteen Stope and a series of ore reserve estimates derived by manual, numerical and disjunctive kriging methods.

Jan 1, 1979

By Jacque Turgeon, Gontran Foy

"The Mineral Research Centre of the Quebec Department of Energy and Resources has worked extensively on the development of a dry process to extract pure mica flakes from a phlogopite ore. The liberation of mica from the gangue is effected basically by impact crushing, and the ground ore is screened into several fractions, each having a fairly narrow range of grain size. Each sized fraction is then fed to an air separator where heavy grains are separated from light flaky grains. Heavy fractions are returned to hammer mills where gangue minerals are ground finer and blocky mica particles are exfoliated. A second stage of screening is performed and each fraction is sent to an air separator. This sequence is repeated until mica products are virtually free of gangue. These different fractions are then treated in a cage mill in which mica flakes undergo a more orderly exfoliation along cleavage planes. The ground mica is again submitted to a final screening stage, after which each fraction constitutes a final commercial product.This process permits the recovery of about 70% of the mica contained in the ore. The over-all process will be described along with technical details of each unit operation. Recent work on a wet grinding method to produce very fine mica will also be discussed.IntroductionRecords of production of mica in Quebec date back to 1886. Production has been more or less continuous since that time, with peak activity during the war years. Production was interrupted in 1966, but started again in 1972 when Marietta Resources and Laviolette Mining and Metallurgical Corporation started their joint operation in Canton Suzor, northwestern Quebec. Mica deposits of more or less importance exist in different parts of Quebec, of which three have attracted attention in recent years: the Canton Suzor deposit, the Canton Lamy deposit and the Canton Chasseur deposit. The Suzor orebody was first identified by Carl Faesler in 1936, who described the rock as ""brown biotite in flakes half an inch in diameter, with interstitial augite, apatite and feldspar""."

Jan 1, 1982

By R. E. Thill

The ultrasonic pulse measurement system described measures velocities of longitudinal (compressional) and shear waves in rock to give values that can be used with density values to determine the dynamic elastic constants of rock. A special feature of this pulse measurement system is its unique acoustical bench that minimizes errors in pulse transit times that are commonly associated with coupling, sample alinement, and sample orientation. Some special features of the acoustical bench are its highly versatile transducer cartridges, a pneumatic ram coupling device, an orientation mechanism, and a vacuum chuck sample holder. The lathe-bed-like construction of the acoustical bench assures automatic alinement of samples and versatility in accommodating samples of various shapes and sizes.

Jan 1, 1968

By Stephen J. Harven

Geologic conditions in eight northern operating sections of Jane Mine, Keystone Coal Mining Complex. Armstrong County, Pennsylvania are defined by utilizing drillhole data and underground geologic mapping. Three of the eight sections are experiencing difficult mining conditions in the Shelocta "0" coal seam (formerly the Lower Freeport). The five remaining productive sections will exhaust their reserves within one year. Coordinating mine planning with future production levels is aided by indicating areas that appear favorable and lack the geologic conditions that cause difficult mining. Roof rock 1 ithologies, lithologic variations in and below the floor, jointing, overburden thickness, coal splits, paleochannels. and clay veins are the principal geologic factors believed to influence mining conditions in Jane Mine. Careful definition of each cause allows for a reasonable assessment of future mining conditions.

Jan 1, 1987

By L. Cheng

This report presents the results of a Bureau of Mines laboratory investigation of the effect of water sprays in reducing respirable dust that escaped the face area of a full-scale wooden model of a mine en-try containing a wooden model of a ripper-type continuous mining machine and exhaust brattice. Areas examined were (a) the general effectiveness of a low-pressure water spray system mounted on top of the mining machine boom, a high-pressure spray system mounted under the boom, and the combined top-and bottom-spray systems, and (b) the effect of these three spray systems on the capture of coal dust particles of different sizes. Dust was injected into a sump cavity at the face. Airborne respirable dust concentration was mea-sured behind the brattice with a personal sampler and cyclone, and particle size distribution was mea-sured with a cascade impactor. When used alone, the top-spray system captured about 55 pct of the respirable dust in the face area and the bottom-spray system captured 60 pct; the capture efficiency of each system is decreased when they are used simultaneously. From a mass-concentration viewpoint, each spray system preferentially captures larger dust particles.

Jan 1, 1988

By N. Kumar Kittusamy

Operators of construction equipment perform various duties at work that expose them to a variety of risk factors that may lead to health problems. A few of the health hazards among operators of construction equipment are: (a) whole-body vibration, (b) awkward postural requirements (including static sitting), (c) dust, (d) noise, (e) temperature extremes, and (f) shift work. It has been suggested that operating engineers (OEs) are exposed to two important risk factors for the development of musculoskeletal disorders: whole-body vibration and non-neutral body postures. Method: This review evaluates selected papers that have studied exposure to whole-body vibration and awkward posture among operators of mobile equipment. There have been only few studies that have specifically examined exposure of these risk factors among operators of construction equipment. Thus other studies from related industry and equipment were reviewed as applicable. Conclusion: In order to better understand whole-body vibration and postural stress among OEs, it is recommended that future studies are needed in evaluating these risk factors among OEs.

Jan 1, 2004