Search Documents

The following pages discuss the objectives, the background, and scope of work of an industrial engineering analysis of far-,n haulage systems in underground retreat coal mining. This study ran concurrently with an existing industrial engineering study of methods of improving safety and production efficiency in underground pillar extraction. 1. OBJECTIVES The objective of this project was to provide basic data inputs that will inpart knowledge as to the major constraint to pillar extraction sections. Furthermore, the industrial engineering study will suggest ways to optimize haulage systems and to develop more efficient work practices and operational techniques that will maximize equipment utilization.

Jan 1, 1975

By J. P. Morris

The Bureau of Mines investigated the mechanics of fuming of iron-carbon melts during top-blowing with oxygen. Melts weighing 45 lb were prepared in an induction furnace and blown with oxygen by means of water-cooled lances. The rate of fuming was measured and correlated with the operating variables. The data showed that the primary cause of fuming was a boil at the bath surface in the impingement zone of the oxygen jet. Nucleation of the carbon monoxide bubbles producing the boil was apparently brought about by the precipitation of an oxide phase. The actual fuming mechanism involved partial oxidation and vaporization of bubble films and fine metal spray generated by the bursting of the bubbles. Bubbles that formed outside the impingement zone produced little fume. The distribution of trace elements between the metal and fume strongly indicated that the fume contained fine spray particles as well as particles that had condensed from vapor. The rate of fuming was found to be proportional to the carbon content of the metal) the concentration of oxygen in the jet) and the bath temperature) provided that a continuous boil occurred. In the absence of a boil) very little fume was produced.

Jan 1, 1967

By John W. Harshbarger

The Upper Santa Cruz Groundwater Basin lies in the drainage area of the Santa Cruz River in Arizona, and extends upstream from the community of Rillito to the international boundary, see Figure 1. The principal water use area lies between and includes the cities of Tucson and Nogales. A subsurface geologic barrier near Rillito provides a reasonable dividing line between the groundwaters of the Upper and Lower Santa Cruz Basins. The Upper Basin contains the Tucson and Sahuarita-Continental critical ground- water areas. The Tucson Water Use Area encompasses the Tucson metropolitan area and extends from the northern boundary of the Basin south to the boundary between the Tucson and Sahuarita- Continental critical groundwater areas near San Xavier. The San Xavier Use Area is the San Xavier Indian Reservation. The north and south boundaries of the Continental Use Area coincide with the limits of the Sahuarita-Continental critical groundwater area. The first study of groundwater in this valley was initiated by Dr. G. E. P. Smith in 1905 and the results were published in 1910, followed by a series of bulletins of the Arizona Agricultural Experiment Station, University of Arizona, covering the general field of groundwater development and utilization. Beginning in 1939, the Ground Water Branch of the United States Geologic Survey, in cooperation with the Arizona State Land Department and the Arizona Water Commission (AWC), have published a series of bulletins concerning groundwater occurrence and utilization in various areas of the state. In 1975 and 1977, the AWC published the "Arizona State Water Plan" (1), comprising a detailed inventory of water availability and use in the State of Arizona, and a study of alternative futures.

Jan 1, 1979

By Robin Phinney

Certain statements in this presentation may constitute "forward-looking" statements which involve known and unknown risks, uncertainties and other factors which may cause the actual results, pe1formance or achievements of the Corporation, or industry results, to be materially different from any future results, performance or achievements expressed or implied by such forward-looking statements. When used in this presentation, such statements use such words as "may", "would", "could", "will", "intend", "expect", "believe", "plan", "anticipate", "estimate" and other similar terminology. These statements reflect the Corporation's current expectations regarding future events and operating performance and speak only as of the date of this presentation. Forward-looking statements involve significant risks and uncertainties, should not be read as guarantees of future performance or results, and will not necessa1ily be accurate indications of whether or not such results will be achieved. A number of factors could cause actual results to differ materially from the results discussed in the forward looking statements including, but not limited to, the factors discussed in the Corporation's annual information form filed on March 9, 2011. Actual results could differ materially from those currently anticipated due to a number of factors and risks. These include, but are not limited to, the failure to obtain necessary regulatory approvals, including environmental approval, the failure to secure full project financing, the failure to implement the recommendations set out in the Technical Report, the failure to raise financing to implement the recommendations in the Technical Report, risks associated with the mining industry in general (e.g., operational risks in development, exploration and production; delays or changes in plans with respect to exploration or development projects or capital expenditures; the uncertainty of estimates and projections relating to production, reserves and resources, costs and expenses; and health, safety and environmental risks), decrease in potash prices and exchange rate fluctuations. Although the forward-looking statements contained in this presentation are based upon what management of the Corporation believes are reasonable assumptions, the Corporation cannot assure shareholders that actual results will be consistent with these fonvard-looking statements. These fon\?ard-looking statements are made as of the date of this presentation and are expressly qualified in their entirety by this cautionary statement. Subject to applicable securities laws, the Corporation assumes no obligation to update or revise them to reflect new events or circumstances. This presentation is a market update based on the Corporation's public disclosure and does not form a part of any offer of securities, or constitute a solicitation of any offer to purchase or subscribe for securities. Any purchase of securities in the company should be made solely on the basis of information contained in the Corporation's public record which is available on www.sedar.com .

May 1, 2013

By George Koenig

I have been granted the outstanding privilege... and pleasure to introduce you this evening to the Grand-Duchy of Luxembourg and to tell you in a few words how this country came into existence, how it managed to survive and what role it nowadays plays in the International Community. Luxembourg, situated between Belgium, Germany and Prance is a small, a very small country... just a dot on a map. After all, it is only a matter of 62 miles from top to bottom and 37 miles across at it's widest... barely covering some thousand square miles... so be careful about stepping on the accelerator... you might be in and out without having realized it... which would be a real shame as the Grand-Duchy enjoys a fairly unique geographical feature in so far as it provides the visitor with an outstanding variety of scenery concentrated in a minute spot.

Jan 1, 1987

By T M. Campos, J Silva, L M. Tavares, J Lichter, L P. Alves, B K. N Rocha, H D. G Turrer

The depletion of the richest ore deposits and the increase in number of mining projects involving deposits with complex mineralogy, higher competence and lower grade has led to an eminent need for improving understanding on multicomponent behaviour in mineral processing. One particularly relevant case is the ball milling of itabirite iron ores fed to the processing plant of Minas-Rio operation in Brazil. Dealing with the two main mineralogical components of the ore, namely hematite and quartz, the operation faces some challenges to improve understanding on how the two components behave in the process. Mathematical models have showed potential to give support in this task, but its applications to describe this type of industrial-scale grinding is still missing. The present work demonstrates the application of a multi-component ball mill model to simulate a closed ball mill circuit with hydrocyclones using the commercial software Integrated Extraction Simulator (IES). Model was calibrated on the basis of bench-scale tests and industrial surveys. Multi-component simulation results are then compared to those considering a single component in the feed, demonstrating the value and great insights that can be achieved by using the former in optimising plant operation.

Aug 24, 2022

By J Vann

The key functions of project evaluation are to assess potential profitability and to develop an effective operational design. For mining projects, design aspects include mining methodology, ore treatment methodology and production rates. All of these characteristics impact on project economics and overall value. Resource models, which form the ultimate basis of project evaluation, typically consist of tonnes above cut-off, grade above cut-off and the spatial distribution (connectivity) of tonnes/grade above cut-off, for one or more variables. Dilution, ore loss and metallurgical recovery are all modifying factors applied to the resource model during evaluation and determination of profitability. A key issue is: how is the value determined? In addition to traditional combination of in situ tonnes/grade, the following merit serious consideration: the concentration of deleterious elements, throughput rates, mining/processing costs and û importantly û metallurgical recovery. Geometallurgy is an emerging field targeted at integrating these issues by identifying either direct measures or proxies for throughput (hardness, grindability), recovery (liberation, mineral shape/texture, etc) and concentrate quality from easily collected macro-, meso- and microscopic data. These ægeometallurgical variablesÆ drive project costs and revenues in a fundamental way. For geometallurgical characterisation to have a real impact on business design, it must enable improved mine planning. When creating spatial estimates for such variables, it is preferable to find proxies that can be measured as close to the intact rock mass as possible. However, spatial estimation of proxies for geometallurgical properties and responses is complex and requires special consideration. Unlike grades, both proxies and absolute measures of geometallurgical variables are not necessarily linear or additive and therefore require very careful geostatistical consideration. In some cases, models must predict extreme values of geometallurgical attributes rather than averages. Incorrect characterisation of metallurgical recovery/throughput can (and has) led to misspecification of the scale of projects, and thus can be seriously value destructive. Aspects of geometallurgy have long been important in iron, bauxite, manganese and coal deposits and are increasingly on the radar for base and precious metal miners. However, as more metallurgically complex deposits are developed and mining of large-scale, low-grade deposits becomes more commonplace, the importance of characterising the metallurgical response in order to generate properly optimised projects will rapidly increase. It is possible that in many ætraditionalÆ (ie grades and tonnes) reserve models, the variables that drive the project are missing!

Jan 1, 2007

The key functions of project evaluation are to assess potential profitability and to develop an effective operational design. For mining projects, design aspects include mining methodology, ore treatment methodology and production rates. All of these characteristics impact on project economics and overall value. Resource models, which form the ultimate basis of project evaluation, typically consist of tonnes above cut-off, grade above cut-off and the spatial distribution (connectivity) of tonnes/grade above cut-off, for one or more variables. Dilution, ore loss and metallurgical recovery are all modifying factors applied to the resource model during evaluation and determination of profitability. A key issue is: how is the value determined? In addition to traditional combination of in situ tonnes/grade, the following merit serious consideration: the concentration of deleterious elements, throughput rates, mining/processing costs and - importantly - metallurgical recovery. Geometallurgy is an emerging field targeted at integrating these issues by identifying either direct measures or proxies for throughput (hardness, grindability), recovery (liberation, mineral shape/texture, etc) and concentrate quality from easily collected macro-, meso- and microscopic data. These 'geometallurgical variables' drive project costs and revenues in a fundamental way. For geometallurgical characterisation to have a real impact on business design, it must enable improved mine planning. When creating spatial estimates for such variables, it is preferable to find proxies that can be measured as close to the intact rock mass as possible. However, spatial estimation of proxies for geometallurgical properties and responses is complex and requires special consideration. Unlike grades, both proxies and absolute measures of geometallurgical variables are not necessarily linear or additive and therefore require very careful geostatistical consideration. In some cases, models must predict extreme values of geometallurgical attributes rather than averages. Incorrect characterisation of metallurgical recovery/throughput can (and has) led to misspecification of the scale of projects, and thus can be seriously value destructive. Aspects of geometallurgy have long been important in iron, bauxite, manganese and coal deposits and are increasingly on the radar for base and precious metal miners. However, as more metallurgically complex deposits are developed and mining of large-scale, low-grade deposits becomes more commonplace, the importance of characterising the metallurgical response in order to generate properly optimised projects will rapidly increase. It is possible that in many `traditional' (ie grades and tonnes) reserve models, the variables that drive the project are missing!

Jan 1, 2007

By C. W. Owings

A few of the more progressive mining companies have taken precautions to safeguard employees or man-trips. Specially constructed men-cars -have been provided with special devices or mechanisms to stop the cars on slopes, if the hoisting cable should break. Cars have been equipped with safety chains to connect and hold them together if a coupling should break. Steel frames covered with heavy wire netting have been placed over cars to reduce injuries to the riders from roof fails on slopes. A safety cable passing from the front car to a point above the cable socket on the slope hoisting cable is used frequently as a precaution in case the socket loosens o the main cable breaks at the socket. Such devices are commendable, but the percentage of man-cars and man-trips protected is relatively small - entirely too small. Man-trips that travel level haulage roads are rarely protected safety devices, and haulage roads are seldom inspected by mine officials to determine the condition of roof and ribs.

Jan 1, 1935

By S. C. Miller, R. D. Carter, H. G. Riley

A merhod based on theoretical considerations is presented for estimating srabilized performance of gas wells from data obtained from short-term flow tests. Calculated results are presented for II gas wells evaluated with four-to five-hour flow tests. For seven wells on which comparison war available, satisfactory agreement between measured and calculated performance was obfained. Although the final results are favorable, diflerences in flow capacity k,h obtained from flow tests conducted at different rates were observed. This inconsistency did not seriously affect the calculated results in the test wells. INTRODUCTION In order to negotiate the sale of gas from newly drilled gas wells and to plan otherwise for the orderly exploitation of gas reserves, it is necessary to predict the long-term withdrawal rates physically possible for each well. Since low permeability gas wells do not stabilize except after a lengthy period of flow, the operator is unable, without wasting large amounts of gas, to measure directly the stabilized performance prior to contracting for sale of the gas and connecting the well to a pipeline. This problem is not new, but is one which has recently received considerable attention because of the rising importance of natural gas in the economy and new emphasis on the development of gas reserves. Thus, a method is needed for estimating stabilized performance from information obtained from short-flow tests in which stabilized flow is not attained. Such short tests would be suitable for wells not connected to a pipeline since the tests require only small amounts of time, labor and production of gas. Other requirements of such a method are short calculation time and use of a model of the gas well and its reservoir drainage area which is as consistent as possible with present theoretical, experimental and field knowledge. The method presented herein was developed in an effort to meet these requirements. It has been named the "two-Row method". In addition to the section on the evelopment and description of the method, a description of field application of the method and a discussion of well test results are in- cluded. Finally, there is a section on an additional consideration prompted by some of the test results. The Appendix contains certain details of the derivation of the two-flow method and a sample calculation for Test Well 1. MATHEMATICAL DEVELOPMENT AND DESCRIPTION OF THE METHOD The method is based upon the following assumptions: (1) The system can be described as a finite cylindrical gas reservoir produced by a single cylindrical well located at the center of the reservoir. Flow is strictly radial. (2) Flow obeys Darcy's law except very near the well where a quadratic flow law is assumed. (3) The system is also characterized by a laminar flow skin factor. The use of a quadratic or turbulent flow term is more fully justified in Refs. 1 and 2. When such a system is opened at the wellbore to constant rate flow from an initial condition of uniform pressure distribution, the radius or drainage quickly passes through the non-Darcy flow and "skin effect" region imrnediately surrounding the well. After the drainage radius or "transient" has passed beyond this region and before it reaches the external boundary, drawdown can be expressed by'." After the drainage radius reaches the external boundary, stabilized flow exists and drawdown is given by'," Eqs. 1 and 2 form the basis for the method. The validity of these equations will now be examined in the light of some well test data previously available. It has been found by actual measurements on gas wells that the relationship between drawdown and flow rate, that is the performance curve, is closely approximated by' Eq. 3 is a straight line on log-log graph paper. Eq. 2 and, for any lixed value of time, Eq. 1 plot as a curve which is slightly concave upward on log-log graph

By Wei Lv, Gangqiang Fan, Xuewei Lv, Kai Tang, Yingyi Zhang

The EAF smelting process of ilmenite concentrate consumes large amounts of energy. Semi-melting reduction can lower the reaction temperature and separate the iron and slag more thoroughly. However, this needs additives and pre-oxidation to promote the reaction. In this paper, the pre-oxidized ilmenite powders were reduced isothermally with graphite and Na2SO4. The influence of reduction conditions on the metallization ratio of samples, such as reaction temperature, and sodium sulfate additive were investigated. The results show that additive such as Na2SO4 can significantly decrease the melting point of pre-oxidized ilmenite concentrate.

Mar 1, 2017

By Yoginder P.

ACKNOWLEDGEMENTS Authors sincerely appreciate the interest, cooperation and technical support of the coal company management and staff in conducting the study. Without their assistance this study would not have been possible. INTRODUCTION AND SPECIFIC OBJECTIVES An area in the midwest overlying abandoned room-and-pillar mine workings at, shallow depth has been experiencing subsidence movements with associated damage to surface structures. Other coal companies in the area have also been having similar experience. A 16 - month cooperative study between a mining company and the Department of Mining Engineering at SIUC was developed with the following objectives. 1) Determine the extent to which surface and subsurface movements were complete in the area, 2) Identify the mechanism(s) of subsidence in the area, 3) Determine the influence of geology and hydrology of the area on subsidence movements, 4) Observe the conditions of abandoned underground workings with a borehole TV camera, 5) Characterize the extent of damage and monitor possible progressive damage to selected surface structures, and 6) Make recommendations to a) minimize further damage to surface structures in the area, b) identify future areas that may be affected by these movements and c) modify mining systems to minimize these movements.

Jan 1, 1986

By W. J. Houk, F. C. Hull

To clarify interpretations of grain structures and to assist in calculations of spatial grain size distributions, plane distribution curves have been determined for random sections through four regular polyhedrons approximating the shapes of metal grains. The characteristics of the distribution curve for the average metal grain are predicted. IT was realized early in the history of metallurgy that metals are polycrystalline aggregates and that the size and shape of crystals affects the properties of the material. Reaumur1 in 1722 employed the microscope to examine the fractured surfaces of steel and of white and gray cast iron and suggested a polyhedral arrangement of the crystals. The first extensive investigation of the form of crystal grains was carried out by Desch.2 He examined the disintegrated grains from a ß brass sample and noted that the number of faces per grain ranged from eleven to twenty and that the number of edges per face varied from three to eight and the maximum occurred at five. While it has been found practical to examine isolated grains only in exceptional cases, it is always possible to make a plane section through the metal and examine the shape of the grain sections on the plane of polish. Desch2 tried to determine the relation between the form of a polyhedron and that of its plane sections for comparison with distribution curves of numbers of sides per grain section of actual metal samples. The polyhedrons investigated were the rhombic and pentagonal dodecahedrons and the orthic tetrakaidecahedron. However, the frequency distributions of the number of sides of plane intersections were not sufficiently characteristic to decide which polyhedron most closely approximated the average grain in a metal. Determination of Statistical Shape of Grain in Space Scheil3 was interested in the problem of calculating the distribution of grain sizes in space from the easily measured distribution of grain section sizes on the plane of polish. Assuming that the grains were spheres and using the plane distribution curve for a sphere shown in Fig. 1, he employed a successive subtraction method to calculate the spatial distribution. In order to evaluate the accuracy of these calculations, Scheil and Wurst4 determined the actual distribution of grain sizes in space in their sample of ingot iron by polishing off successive layers and following every individual grain in a series of micrographs. From curves of mean radius of intersection of a given grain vs thickness of metal removed in polishing, Scheil and Wurst attempted to derive the statistical shape of a grain in space. Their calculated plane distribution curve for this shape is compared with the distribution curve for a sphere in Fig. 1. A table of values based on this curve was prepared for calculating spatial distributions of grains. The calculated and measured spatial distributions of their sample then agreed much better than when a spherical shape had been assumed. In the present paper, an attempt has been made to learn something about the average metal grain by studying in detail the effect of the shape of regular polyhedrons on the plane distribution of areas and shapes of areas produced by random sections through them. From the data presented below, it can be concluded that the plane distribution curve for the average metal grain differs in three fundamental respects from the curve derived by Scheil and Wurst. Polyhedrons Selected for Study The polyhedrons selected for the statistical study are illustrated in Fig. 2 and consisted of a cube, a figure formed by cutting off the corners of a cube at the midpoints of the original edges, a tetrakaidecahedron, and a pentagonal dodecahedron. The length of edge on any one figure is a constant. For the above models the edge lengths were 3.50, 4.00, 2.00, and 2.08 in., respectively. A cube was selected for one of the polyhedrons because of its simple geometry, because it is a form that by repetition can completely fill space, and because it represents a convenient degree of departure from compactness beyond which the shape of

Jan 1, 1954

By Arthur C. Pincomb, Alan R. Shapiro

A public awareness of and commitment to abate pollution of water, air, and soil continues to stimulate demand for industrial minerals and rocks capable of neutralizing strong and weak acids. The role of acid neutralizing agents is 1) to treat acidified water and soil until the desired pH is attained and 2) to remove acid-forming compounds from industrial processes to mitigate the formation of acidic discharges. Environmental applications for these agents include: acid rain mitigation, neutralization and prevention of acidic industrial process discharges, and treatment of acid mine drainage and coal refuse. Desulfurization of industrial flue gases involves removal of sulfate compounds capable of combining with hydrogen to form acids. Details of flue gas desulfurization are covered in the previous chapter on Flue Gas Desulfurization. Ideally, the neutralization of acids results in an upward adjustment of effluent pH 7, or neutrality. The final pH value for many acid treated wastes, especially industrial discharge streams, is commonly over neutralized to pH 8.5 to 9.5. The Clean Water Act sets the upper discharge limit at pH 9. ACID NEUTRALIZATION REAGENTS Acid neutralization is accomplished by adding alkali metal and alkaline earth metal compounds to acidic water or soil until the desired pH is attained. The commonly used alkali ions are calcium (Ca), magnesium (Mg), sodium (Na), and potassium (K). Sodium hydroxide, high calcium and dolomitic hydrate, high calcium and dolomitic lime (quicklime), high calcium and dolomitic limestone, soda ash, and magnesium oxide are the compounds most commonly applied to raise the pH of acidic waters or soils. Limestone and dolomitic limestone, which are calcium and magnesium carbonates, and their equivalent oxides and hydrates formed by calcination, are the industrial materials most commonly used in the manufacture of reagents for acid neutralization. Approximately 327 kt of high calcium and dolomitic lime were consumed for acid neutralization purposes in 1988. Magnesite and brucite are industrial minerals that compete with dolomitic limestone for the magnesium-oxide market. Production of caustic calcined magnesia for neutralization purposes exceeded 6 kt in 1990. Soda ash is an industrial mineral gaining increased acceptance in the neutralization of acid waste discharges. Approximately 182 kt of soda ash were consumed in 1990 for acid waste treatment or acid prevention by flue gas desulfurization. Other mineral products either consumed in minor quantities or receiving attention as future neutralizing agents include zeolite and hectorite. In some cases, waste products have been found to be suitable and cost effective for neutralization of acids. Common wastes gaining acceptance include basic slag, phosphate mining refuse, cement kiln dust, fly ash, and mine tailings.

Jan 1, 1994

By J. P. Dai

The Fankou Mine in Guangdong province, China, processes a polymetallic ore containing averagely 4.2% Pb, 8.5% Zn, and 90 g/t Ag. The main metal minerals including sphalerite, galena and pyrite are very finely disseminated and unevenly occurred in the ore, making it difficult to liberate them from each other. This paper presents the processing technology of the Fankou plant and the characteristic features of the novel technology applied.

Jan 1, 2014

By Gene D. Clayton, Robert R. Dimock

A time-consuming and expensive preshearing program to minimize the adverse effects of blasting on slope stability at Kennecott Copper Corp.'s Ruth Pit in east-central Nevada has been eliminated in favor of down-the-hole, nonelectric delayed blasting which can produce a smooth wall effect and improve blast fragmentation. The new blasting approach resulted from a Kennecott engineering investigation aimed at improving the stability of the extremely variable rock conditions found throughout the pit by reducing the vibrational energy imparted to the walls with conventional bench blasts.

Jan 4, 1977

By J. P. Newell, R. W Storey

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. AUGER mining is a form of continuous mining in that it completely replaces with a one-cycle operation the older conventional cut, drill, shoot, and load method of mining. Relatively new, having been utilized only within the last few years, it is even more continuous in its production of coal than some other forms of continuous mining being practiced in this country today. There are at present coal recovery augers in operation working along strip-mined highwalls from the outside. This paper will deal with underground mining, specifically with an experiment which was carried out with a machine developed for this purpose. The location of this experiment was in Pike County in eastern Kentucky in the upper split of the No. 3 Elkhorn seam. Coal height was 32 in. and roof conditions were very bad, with 10 in. of soft draw slate coming down with every cut in conventional mining. The coal is high-grade bituminous, excellent for metallurgical coking. Underground auger mining fills a need for a method of recovering coal in thin seams, under bad roof conditions or in split seams. In many cases it might save money by eliminating the handling of excessive quantities of rock. In fact, if the coal can be recovered, as in the case of this experiment, without mixing with any impurities outside the seam, it may be possible to load or ship a satisfactory product with little or no preparation or cleaning expense. The need for some economical method for recovering coal from thin seams is becoming more pressing as the more profitably mined seams are exhausted. Basic Principles of Auger Mining The principles of the auger, or screw conveyor, have long been used in drilling small diameter holes for blasting and other purposes. These same fundamentals apply to large diameter drilling. However, considerably more attention was given to designing a cutting head that would not pulverize the coal and consequently would require a minimum of power to drive it. The head, as designed for this job, consists of a cylinder 25 in. in diam with steel bits set in 3 positions spaced around the forward rim. A conventional coal drill bit, at the head of a bursting cone in the center of the cylinder, trails the forward rim slightly, see Fig. 1. The bursting cone and auger connections are anchored to the cutter barrel by 3 arms spaced at 120". This head design proved to be very satis-

Jan 1, 1953

By J. P. Newell, R. W. Storey

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. AUGER mining is a form of continuous mining in that it completely replaces with a one-cycle operation the older conventional cut, drill, shoot, and load method of mining. Relatively new, having been utilized only within the last few years, it is even more continuous in its production of coal than some other forms of continuous mining being practiced in this country today. There are at present coal recovery augers in operation working along strip-mined highwalls from the outside. This paper will deal with underground mining, specifically with an experiment which was carried out with a machine developed for this purpose. The location of this experiment was in Pike County in eastern Kentucky in the upper split of the No. 3 Elkhorn seam. Coal height was 32 in. and roof conditions were very bad, with 10 in. of soft draw slate coming down with every cut in conventional mining. The coal is high-grade bituminous, excellent for metallurgical coking. Underground auger mining fills a need for a method of recovering coal in thin seams, under bad roof conditions or in split seams. In many cases it might save money by eliminating the handling of excessive quantities of rock. In fact, if the coal can be recovered, as in the case of this experiment, without mixing with any impurities outside the seam, it may be possible to load or ship a satisfactory product with little or no preparation or cleaning expense. The need for some economical method for recovering coal from thin seams is becoming more pressing as the more profitably mined seams are exhausted. Basic Principles of Auger Mining The principles of the auger, or screw conveyor, have long been used in drilling small diameter holes for blasting and other purposes. These same fundamentals apply to large diameter drilling. However, considerably more attention was given to designing a cutting head that would not pulverize the coal and consequently would require a minimum of power to drive it. The head, as designed for this job, consists of a cylinder 25 in. in diam with steel bits set in 3 positions spaced around the forward rim. A conventional coal drill bit, at the head of a bursting cone in the center of the cylinder, trails the forward rim slightly, see Fig. 1. The bursting cone and auger connections are anchored to the cutter barrel by 3 arms spaced at 120". This head design proved to be very satis-

Jan 1, 1953

By R. H. Cox, A. S. Allen, James Paone

The southwestern Illinois communities of Belleville and Maryville lie within the greater metropolitan area surrounding St. Louis. Missouri. They also lie within that part of the Illinois coal basin where the Number 6 coalbed has been mined for more than a century. About half the coal was left as pillars to support the ground surface. Years later, however, damaging movements are affecting buildings, streets, and public utilities in some areas. They are generally believed to be related to abandoned mine workings. The threat of continued or increasing incidence of damage raises the need to explore other subsidence-control measures for protecting affected areas with high population density. Because of experience gained in a subsidence-control program of backfilling abandoned coal mines in the Applachian region and in Rock Springs, Wyoming, the Bureau of Mines was called upon to investigate the subsidence occurrences at Belleville and Maryville, and recommend protective measures. Funds ware appropriated for the Bureau to initiate subsidence-control projects at two residential sites in Belleville and one in Maryville. Subsurface investigation of the sites by diamond core drilling revealed two conditions that differ from those encountered at most sites of previous subsidence-control projects. The mine workings were found to be dry and the mine floor consisted of soft underclay which characteristically loses strength with increase of moisture. It had been anticipated that water would have percolated into the mine workings at one .or more of the sites through cracks resulting from subsidence. Under such conditions Bureau engineers believed that injection of mine waste by the pumped; slurry technique3 would provide support and stabilize any movements initiated by the softening of the clay. With discovery that the underclay deposits at the three sites have apparently not been exposed to water since the mines were operating, hydraulic backfilling of any type was considered inadvisable on the basis of present knowledge. To avoid introducing water, a portable pneumatic system is being devised for injecting minus 0.01 27 m (1/2 in.) mine waste into the mine workings. Machines for pneumatic backfilling have been used in Europe not only for subsidence protection but also for strata control, for reducing spontaneous combustion and methane accumulation, and as a means of waste disposal. The Bureau experimented with a pneumatic machine in the Northern anthracite field of Pennsylvania in the 1950's. Previously pneumatic machines have been installed in active mine workings discharging from horizontal pipelines which conveyed air- borne material into rooms to be filled. In the present adaptation to abandoned mines, the machine and air compressor will be operating at the surface, to impel material vertically down injection boreholes with sufficient air pressure to disperse fill material laterally in mine workings at the base of injection holes. Large diameter access and ventilation boreholes will be provided at one site for entry into mine workings to observe backfilling progress. The Belleville and Maryville projects are part of the Mined Land Demonstration Program of the Bureau of Mines. The Illinois State Geological Survey and Department of Mines and Minerals are furnishing technical support.

Jan 1, 1979

By H. Kohno

The Onahama No.3 tankhouse started commercial operation in early 1973, with the capacity of 8,500 metric tons per month. When the No.3 tankhouse was constructed, the starter sheet stripping section was rebuilt at the No.2 tankhouse and electrolyte purification section was expanded. The previous AIME paper in 1976 described the design principles of the No.3 tankhouse and its layout, This paper describes the starter sheet stripping machine in the No.2 tankhouse and the electrodes handling system in the No.3 tankhouse and all these equipments were developed for the operation of the No.3 tankhouse. A Hazelette continuous casting machine was also introduced in order to cast thin anodes with accurate shape. Owing to the adoption of thin anodes, gold, silver and copper inventory is reduced by 40%. Jumbo tanks and newly developed mechanical equipments were adopted and no work on cells during pulling up operation was achieved. Using thin anodes with accurate shape, inspection work was completely abolished while maintaining high current efficiency and high cathode quality. Labor cost was reduced by 70% and only six operaters can produce? 8,500 metric tons of cathodes per month. The same new electrolysis process is appreciated and has been used as a newly built independent tankhouse by Kidd Creek Mines Ltd., in Canada in 1981 with excellent results

Jan 1, 1987