Search Documents

By Lance Helwirg

New high and low double outfall bridge structures for a juvenile fish bypass system have been constructed on the Washington Shore approximately two miles downstream from the Bonneville Dam on the Columbia River. The high and low outfalls each extend approximately 400 feet into the river from the Washington shore and are designed to release juvenile salmon into the river at above-water discharge elevations for improved survival rates. The two outfall structures include post-tensioned concrete double box flume girders approximately 7 feet high by 13 feet wide, which will be submerged in river flows as high as 15 feet per second. Each of the 6 offshore foundation piers is composed of a single 10-foot diameter reinforced concrete drilled shaft with a permanent steel casing embedded into the river bottom approximately 100 feet. Challenging outfall design conditions included designing the entire structures to be submerged for long periods of time in 15-feet-per-second river water flow with a 60-foot cantilever at the end of each outfall, and with the superstructure 70 to 80 feet above the river bottom. Figures 1-1,1-2, and 1-3 show the high and low outfall structure overhead photos and elevation view.

Jan 1, 2001

By Terry J. Close

In 1986 and 1987, at the request of the U.S. Bureau of Land Management, U.S. Bureau of Mines personnel studied 7,040 acres of the 7,240-acre Sheep Mountain Wilderness Study Area (OR-006-003) in order to evaluate its identified mineral resources. The area studied is along the divide between the Snake River and Pine Creek about 1.5 mi south of the village of Oxbow in Baker County, OR. No mineral resources or mineral-related activities were identified in the Sheep Mountain study area. The basalt covering most of the study area has no known mineralized sites. However, it contains common agate and opal that is of limited interest to mineral collectors. This basalt (stone) could be used locally as construction material (crushed stone or fill); however, suitable material is wide spread in the region and more accessible to possible markets.

Jan 1, 1987

By Stephen H. Partney

Waste clay ponds are a necessary part of phosphate rock beneficiation. They are large, averaging 2.6 km2 (1 sq mile). They are unsightly in that they protrude 6 to 15 m (20 to 50 ft) above natural grade. Stabilization and reclamation is slow and they have had a history of catastrophic failure. Florida has never published a specific rule regarding the configuration or height of these ponds. But it has enforced several policies along these lines. The phosphate industry has been forced to make major monetary decisions that affect mine economics for decades. The Florida Bureau of Mine Reclamation believes that the direction of regulation has been solidified but changes are still anticipated. Phosphate rock has been mined in Florida since 1890 (Fig. 1). Three notable technological changes occurred in the industry that led to major shifts in mining technique and volume. By about 1915, hydraulic mining had been replaced by centralized washers. Hydraulic mines usually started at an outcrop in or adjacent to a stream of the pebble zone. Water was pumped out of the stream through high-pressure monitors and sand and clay were washed away from the pebble. Mobile grizzlies and screens were used in conjunction with animal and human labor to concentrate the pebble and haul it away. Populations were sparse and the clays washed into the stream were considered an acceptable price for the commerce. The clays were not voluminous because the pebble zone typically contained relatively small amounts of them. Machines largely replaced animals by 1910 and provided greater efficiency of production. Centralized washers replaced mobile trommels. They allowed greater ease of access to shipping routes by rail. Some clays were placed in mine cuts from 1915 to 1930. Some were dammed off to increase the capacity of a given site. Some of these also failed, leading to clay plumes that were visible all the way to the Gulf of Mexico. By concentrating the waste clays (slimes) in impoundments, the solids concentration had increased, making plumes persistent for long distances. There were complaints. But there was no litigation against the companies during that time. In 1930, flotation technology allowed the recovery of the phosphate from deeper zones. This was because the "concentrate" size phosphate rock was in the sand-size range and could not be screened out. Centralized beneficiation plants grew into a three-step process - washing and screening, feed preparation and flotation (Fig. 2). Reagent storage, safety and the flotation cell complex made the plants into large capital installations. Larger draglines were required to dig deeper into the matrix. These had dramatically larger production capacities, which were then figured into the overall material balance for a given plant. The number of operators shrank and the production per operator grew. Larger areas were being bermed off for waste clay storage. An economic incentive became apparent for storing as much waste clay as possible in each settling area. At the same time, the population was steadily growing and more eyes were watching the activities of the phosphate mines. Phosphate mining, focused on production and profit, was earning a bad name from its neighbors. When the subject of phosphate mining

Jan 1, 1998

By R. W. Raymond

In a former paper (Trans., xvi., 770) I gave the text of the archaic mining law of the State of New York, together with some comments upon its curious provisions. In that connection I pointed out two facts : first, that the law seemed to have originated in the schemes of private parties, who were satisfied with those parts of it which concerned them particularly; and secondly, that the remaining provisions had been hitherto quite inoperative, for the reason that mines of the character to which they referred had not been discovered in the State. Since 1888, when that paper was written, the New York Legislature has passed several acts relating to mines as follows: 1. Chapter 394, Laws of 1890. This provides for an inspection

Jan 1, 1895

Organization Place Date 1919 American Society of Civil Engineers..: Twin Cities, Minn. June 17-20 American Society of Mechanical Engineers Detroit, Mich. June 17-20 American Institute of Chemical Engineers Boston, Mass. June 18-21 American Drop. Forge Association Pittsburgh, Pa June 19-21 American Institute of Electrical Engineers Lake Placid, N. Y. June 24-27 American Society for Testing Materials Atlantic City, N. J. June 24-27 Society for Prom. of Engng. Education Baltimore, Md. June 25-28 American Chemical Society Philadelpia, Pa. Sept. 2-6 National Assn. of Stationary Engineers Huntington, W. Va. Sept. 8 American Peat Society.. Minneapolis, Minn. Sept. 22-24 American Iron; Steel Electrical Engineers St. Louis, Mo. Sept. 22-26 American Institute of Min. and Met. Engineers, Chicago, Ill. Sept. 22-27

Jan 6, 1919

By E. T. Turkdogan

This paper deals with an analysis of the conditions leading to the formation of blowholes and surface and subsurface defects in cast low-carbon steels. The theoretical analysis of the problem is based on the concept of the occurrence of deoxidation reactions during cooling of liquid steel and during its solidification. The reaction equilibrium data are given on deoxidation of steel by carbon, silicon, and manganese. The details of the calculations are given on the simultaneous deoxidation of steel by silico-manganese additions to produce a desired level of deoxidation at certain residual concentrations. Based on an idealized model, an attempt is made to calculate the enrichment of solutes in the solidifying liquid entrapped within the interdendritic cells which are known to be less than 200 µ thick. Formulae are derived for the calculation of the change in the residual oxygen content of the enriched liquid steel, controlled by Si/Mn deoxidation. It is shown that for every particular initial silicon, manganese, and oxygen concentration in steel (as residuals in liquid solution at the beginning of solidification) there is a particular carbon concentration below which carbon monoxide, leading to blowholes or pinholes, is not expected to form. There are a number of independent variables which have a decisive influence on the formation of blowholes. For example, it is shown that the position of the curve depicting the critical relation between initial silicon and carbon content for suppression of the evolution of carbon monoxide) can be shifted to lower silicon or higher carbon levels by: increasing manganese content; decreasing oxygen, hydrogen, or nitrogen content; or increasing external pressure on the solidifying mass. FOR the production of sound castings it is essential to prevent the formation of interdendritic worm-holes or pinholes brought about by gas evolution during solidification. Another major problem encountered in solidification of ingots is the formation of surface defects. These problems are thought to be closely associated with the deoxidation reaction occurring in liquid steel during cooling and subsequent solidification. As the liquid becomes richer in impurities during dendritic solidification of steel, a series of reactions may occur in the liquid phase trapped within the branches of growing dendrite platelets. Because of the strong interaction between dissolved oxygen and impurities in liquid steel, the reactions most likely to occur are of the deoxidation type. However, inherent to the extreme complexity of the problem in question, numerous simplifying assump-

Jan 1, 1965

By Ricardo Boullosa

El presente trabajo describe el sistema de bonificación como método de incremento de producción en el personal de la minería. El diseño de estos sistemas beneficia al trabajador y a la empresa, así como permite obtener ganancias sobre la base propuesta. Entre los sistemas de incentivos más conocidos figura el sistema de Halsey, Rowan y Barth. Asimismo, tenemos los sistemas en los cuales las ganancias varían en proporción al rendimiento y aquellos con ganancias variables a diferentes niveles de rendimiento como el de Taylor y Merrick. En ese sentido, la administración debe garantizar el apoyo necesario para el avance de incentivos, actualizándolos periódicamente.

Nov 8, 1982

By E. V. Deshayes, W. E. Young

"INTRODUCTION The Camp Bird mine was investigated by Bureau of Mines engineers 3/ September 22 and 24, 1942, and April 29 and 30, 1944. In a subsequent report and supplement, it was recommended that core drilling be done below the 14th. level to determine if commercial ore existed at greater depths, and particularly if ore existed in the vein or adjacent thereto where it passes into the sedimentary formations estimated to underlie the volcanics approximately 400 feet below the 14th level.Seven diamond-drill holes aggregating 3,956 feet were drilled. Four of these holes were under the Hematite ore body and three were under the Big Discovery ore body. Two holes under, the Hematite ore body wore directed at angles but little steeper than the angle of dip of the vein and penetrated the sedimentaries beneath the volcanics close to the vein. Enough low-grade ore was found at the base of the Telluride conglomerate to indicate the presence of a large body of low-grade zinc sulfide ore. Two holes were directed to crosscut the vein at a depth of approximately 125 feet below the 14th level. No commercial ore was cut, but the vein showed the average width and same general characteristics as at the 14th level. One hole under the Big Discovery ore body was directed to crosscut the vein and test the base of the Telluride conglomerate in the footwall block. No commercial ore was found in either the vein or the sedimentary horizon. One hole was directed to test the base of the Telluride conglomerate in close proximity to the vein in the hanging-wall block. This hole was lost approximately 100 feet short of its objective, and a third hole was drilled to accomplish this same thing. The third hole was stopped approximately 50 feet short of its objective when failure of equipment caused a recess of the"

May 1, 1948

A New Technology of Applying SLon-2500 Magnetic Separator to Recover Iron Concentrate from Abandoned Tails

Sep 13, 2010

Flotation of Composite Synthetic Particles

Sep 13, 2010

By Roshan B. Bhappu

The extraction of gemstones, except for diamonds, continues to be a more or less handpicking type operation all over the world. However, considering the physical properties of gemstones such as density (sp.gr.), color, size, shape, luster, brilliance, reflection of light and the like in contrast to the relatively ‘dull’ physical characterization of the associated gangue minerals, it should be feasible to recover several gemstones using modern mineral processing techniques. This paper illustrates the unique physical characterization of several gemstones and suggests appropriate mineral processing techniques that could be used to recover these precious stones. Special emphasis is placed on the versatility of the Heavy Media Separation (HMS) process for processing of the gemstones. Finally, a few examples of commercially viable operations involved in the recovery of emeralds and rubies are presented.

Jan 1, 2005

By John J. Gilman

BECAUSE of their layerlike structure, zinc crystals exhibit strong anisotropies for almost all physical and chemical properties. This should, and indeed does, greatly influence the plasticity of zinc for various crystal orientations. At low temperatures, the investigator of this plastic anisotropy is plagued by the great variety of deformation modes that operate. However, at high temperatures (250° to 419°C) only two deformation modes predominate: basal (0001) and prismatic (1010) glide. Furthermore, since strain hardening is virtually absent at high temperatures, the plasticity for these two modes of deformation can be very simply described by means of two equations of state. It is the purpose of this paper to describe the experimental behavior of basal and prismatic glide in zinc crystals, and to interpret this behavior in terms of other physical properties (in particular, the thermal expansion coefficients and the elastic constants) using the theory of dislocations. Fig. 1 defines the two planes of the zinc structure that will be discussed. Glide occurs very readily on the basal planes at all temperatures, and there is a very large literature on this subject. Much of the literature has been reviewed by Schmid and Boas;' it will not be reviewed here. Kolesnikovl was the first to show that if basal glide is circumvented by stressing a zinc crystal parallel to the basal planes (giving zero shear-stress on the basal planes) then, at temperatures above about 320°C, glide on the first-order prism planes occurs. His results have recently been confirmed by Cahn, Bear, and Bell." These previous workers have established the existence and crystallographic elements of prismatic glide; the present paper is concerned with the stress, strain rate, and temperature relations of prismatic glide as contrasted with basal glide. Experimental Methods The crystals were square ones, 6x6 mm, that had been grown in precision Pyrex tubes by a method that is described in detail elsewhere.' Most of the crystals were 99.999+ pct Zn (New Jersey Zinc Co. CP grade). Some were alloyed with 0.1 -+-0.005 atomic pct Cd, and chemical analysis showed that almost all of the added cadmium persisted through the crystal-growing process. For measurements of nonbasal glide, crystals were oriented with their basal planes parallel to both the rod axis and one of the flat faces of the square cross section. However, the orientation of the close-packed directions [1210] with respect to the rod-axis was variable. For basal glide measurements, the angle between the basal plane and the specimen axis was 35". The orientations were measured by the Gren-inger back-reflection X-ray method. The problem of finding a suitable method of gripping the crystals was the most serious experimental obstacle that arose. Because of the large plastic anisotropy of zinc, the usual gripping methods were unsatisfactory. Some methods that were tried were: high melting-point solder, making heads on the ends by locally melting a crystal, and electroplating nickel on the ends to form enlarged portions. For all these methods, the regions of the grips were weaker than the crystals themselves. Finally, two methods were decided upon: bend tests and direct machining of tensile specimens. In the bend tests, specimens were loaded as simple beams so that gripping was not a problem. The beams were 1 in. long and the axis of bending was parallel to the hexagonal axis of the crystals. For the crystals that were machined into tensile specimens, brass bars with slots in them were used to support the crystals, and thereby minimize the distortions due to machining. The crystals were glued into the brass bars with plastic cement which was later dissolved away with acetone. See Fig. 2, left. No clamps were used near the crystals and the machining was done using a milling machine with a fly-cutter. The tool bit was very sharply pointed to minimize burnishing. The feed was less than 1 mil per cut. The depth of cut was 2 mil for roughing cuts, and % mil for the finishing cuts. This machining method produced surface layers of tiny recrys-tallized grains only 2 to 3 mil deep, and the bodies of the crystals were not measurably disturbed. After the crystals had been machined and removed from the brass holders, they were chemically polished until about 5 mil had been removed from all their surfaces. The polishing reagent consisted of equal parts of concentrated HNO,, 30 pct H3O and ethyl alcohol; it is described in detail elsewhere." A typical crystal is shown in Fig. 2, right. The I-shaped faces are normal to the hexagonal axis of the crystal; otherwise the projections at the ends would simply shear off when the crystal was loaded. The cross section in the 2?-in. gage length is 0.215x0.115 in. It was found that the polished

Jan 1, 1957

By H. C. Schultz

CERTAIN local conditions were known to govern in large measure the successful adaptation of liquid-oxygen explosives to the large-scale blasting at Chuquicamata. The wide variation in hardness of the rock at this mine makes necessary the use of several types of explosives. A locally manufactured, relatively cheap black powder is used in blasting the softer waste and capping material, where a thorough displacement, breaks the ground sufficiently. Before the introduction of L. 0. X., an ammonia dynamite of about 65 per cent. strength was being used exclusively in the harder underlying orebody, where a strong disruptive as well as a displacement effect is required for breaking the ore. The L. 0. X., as developed for quarry work in the United States, has a practically pure carbon cartridge material, and the explosive has an extremely high rate of detonation, which should therefore cause it to usefully develop its full disruptive effect in hard ground. The individual blasts at Chuquicamata are large, black-powder shots which dislodge masses of rock averaging 250,000 tons each, and dynamite shots which dislodge masses averaging 80,000 tons each. It was desirable, therefore, to attempt to displace with L. 0. X. the faster, higher-cost ammonia dynamite used in the smaller blasts. It was not considered practical to attempt to displace the low-cost black powder with L. 0. X., as estimated costs showed no probable saving if this were accomplished. Since it was desirable to continue shooting relatively large blasts for effective operation, it was recognized that larger storage facilities than had been in use would be needed for the liquid oxygen. Because of the difficulty of transporting and discharging large storage containers of efficient design, the better plan appeared to be storage and discharge of the liquid at the place of manufacture, and transportation of the filled soaking boxes to the blast.

Jan 1, 1928

By J. A. Brierley, Roshan B. Bhappu, D. H. Reynolds, P. H. Johnson

Although the economic importance of recovering copper by leaching of mine work dumps from open-pit operations has been realized for some time, serious attempts to understand and to improve such operations through scientifi research has been made only in recent years. This progress report covers the results of chemical, physical, and biological studies pertaining to the dump-leaching process and discusses salient features and parameters that may be helpful in improving such operations. The dump leaching of low-grade copper ores, as an integral part of the open-pit mining operations in the Southwest, has been practiced for the last 50 years and is increasing in importance as one of the major sources of copper. The recent acceleration in dump leaching can be attributed to: (1) the greater tonnages of low-grade ores mined and dumped at newer mines as well as resulting from increased stripping ratios at the older mines, (2) the relatively small investment required for dump leaching facilities per pound of copper recovered contrasted with expansion of milling facilities to recover equal amounts of the metal by raising tonnage throughout, (3) low labor requirements needed for leaching, and (4) the simple and continuous nature of the process needing little close supervision of trained operators. In the past, the mining companies have not worried about efficiency in dump leaching but have been satisfied with whatever metal recoveries could be made without much effort. However, because of the huge amounts of metal accumulating in the low-grade waste dumps, compared to the relatively small amount recovered annually, an operator today cannot leave dump leaching to chance. What appears to be a simple, empirical process is actually a very complex one involving a large number of critical factors that encompass Several Scientific disciplines, such as physics, chemistry, geology, biology, and hydrology. It is imperative that

Jan 1, 1970

By Lionel Roberge, Borge J. G. Fredriksson

"Late in 1981, a six-rope friction hoist was installed in the Number 2 shaft at Les Mines Seleine Inc. on the Madeleine Islands in Quebec. This paper deals with the reasoning behind the selection of hoisting equipment from the economical point of view, safety point of view, future needs point of view, etc.After establishing the basic parameters for the hoisting system, features of the most common types of hoists (i.e. single-drum hoist, double-drum hoist, Koepe hoist) are briefly laid out. The reasons for selecting a friction (Koepe) hoist are summarized. However, why go for a six-rope hoist rather than the (in North America) more common four-rope hoist? As the subject hoist is the first six-rope hoist in Canada, this question is studied in more detail, covering initial cost, maintenance cost, etc., as well as practical aspects, such as safety, physical dimensions, etc.In summary, experiences from other multi-rope hoist installations world-wide are presented.BackgroundIn 1980, Seleine Mines Inc. was established as a subsidiary of SOQUEM. The new mining company was to develop and operate a salt mine and associated harbour on the Madeleine Islands in the Gulf of St. Lawrence. The Madeleine Islands form part of the Province of Quebec. The mine has a planned annual output of 1.2 million metric tonnes of salt, with reserves in sight for over 20 years. Mining will be by room and pillar, with an underground primary crusher and treatment plant. From the underground treatment plant, the salt will be transferred via conveyors to a 5.5-metre-diameter circular shaft and hoisted to the surface. Surface transportation to the warehouse will again be via conveyor, and a conveyor will also transport the salt from the warehouse to the point of shiploading."

Jan 1, 1983

By M. Mezzetti, E. Anders, O. Popov, P. Hoske, H. Lieberwirth, M. Voigt

"The material breakage induced by high energy electric discharges is known in general as electric impulse technology. This technology can be used for processing solid materials, such as rocks and ores. The electric impulse technology has been around for about 60 years, originally developed and intensively investigated by Russian researchers. However, the application fields have been limited to research and laboratory scale projects. Currently, there are new attempts to transfer this technology into practical industrial applications. Practical examples include drilling of deep geothermal wells with an electric impulse driven drill-head. Traditional comminution implies high energy consumption, hence, high costs. The Electric Impulse Technology is interesting for comminution of mineral and complex ores since it could allow improved recovery and energy reduction, thus resulting in significant savings. Another advantage is the dust free processing, which contributes to make minerals processing environmentally friendly. The use of electrical comminution for processing complex ores is investigated within the ELIZE research project funded by the BMBF (project No. 033R161 A) and industrial partners. The main objective is the development of an industrial scale electrical comminution machine. The first development stages include the investigation and characterization of the electric impulse induced weakening on rocks and ores. The characterization results of the preliminary trials at the microstructural scale on granite, skarn and greisen will be presented and discussed in this article. INTRODUCTION The pioneer work in the area of electric impulse technology was conducted by Russian researchers about 60 years ago [1]. While there have been some successful attempts to transfer this technology into practical applications, such as rock processing [2], laboratory processing of mineral ores [3–5], recycling [5] and geothermal drilling [6–9], the jump into practical industrial large scale application has not been accomplished yet. The Institute of Mineral Processing Machines of the TU Bergakademie Freiberg currently leads a project which can be seen as the next logical step for the technology transfer to industrial applications, namely, the development of continuously operating complex ore processing machines based on the electric impulse technology."

Jan 1, 2018

By R. E. Zimmerman

The separation of fine sizes of coal from its impurities by means of various flotation methods has become of increasing importance in the coal industry. This, no doubt, will be even more so in the future as the quantity of high grade coal is depleted, particularly that used for metallurgical purposes. The purpose of this paper is to describe and report the results of research work done under the auspices of the Pittsburgh Coal Co. to determine the amenability of their bituminous fine sizes of coal to flotation, to investigate the value of various reagents and factors affecting their use, and compare the results between froth flotation and bulk oil flotation. Compared with the preferential flotation of complex minerals, or ores, the flotation of coal is comparatively easy. However, this statement should not lull one into the feeling that there are no special problems involved. For instance, the separation of coal from pyrite in high sulphur coals is still far from being 100 pet successful. Size consist has considerable effect on reagent consumption and recovery. Other factors will be described and finally it must be remembered that in the flotation of coal a low priced material is being treated and thus economic considerations govern more closely its application than is generally the case in treating other minerals. As a result of the research work done by the Pittsburgh Coal Co. on the flotation of coal, it was concluded that it was practical to clean the —48-mesh coal commercially by froth flotation and after several different types of flotation units and circuits were investigated by means of pilot plants, large scale units were installed at their Champion Nos. 1, 4 and 5 Preparation Plants for the cleaning of —48-mesh slurries. These large scale operations have been recently described by D. H. Davis.' C. P. Proctor and C. B. Carlson2 in their chapter on Froth Flotation of Coal in the AIME Seeley W. Mudd series book on Coal Preparation describe some of the practical applications of our Pittsburgh Coal Co. laboratory work in actual plant practice as well as summarizing part of the investiga-tional work. The author presents this paper, however, as a supplement to their reports, and records the basic research accomplished in the laboratory investiga-tional work as well as the results of experiments using bulk oil flotation. In presenting this work the author wishes to state much more work must be done in applying the principles of flotation to cleaning coal, especially in view of recent studies and practices in other mineral beneficiation fields. Methods of Conducting Laboratory Tests The bulk of the research work was conducted in the laboratory of the Champion No. I Preparation Plant. This plant has elaborate facilities for sampling and analyzing coal and proved to be an admirable location for the investigational work. Four types of laboratory flotation ma-

Jan 1, 1949

By Hebert Arias, Christian Mendoza, Mervin Tapia

El Complejo Pasco —ubicado en la Cordillera Oriental de los Andes de la sierra central del Perú, en el distrito de San Francisco de Asís, provincia y departamento de Pasco— está constituido por las unidades subterráneas de Atacocha y Porvenir, la operación a tajo abierto Glory Hole y tres proyectos brownfield ubicados en la periferia de la concesión. Tanto Atacocha como Porvenir son depósitos tipo skarn, con mineralización distal de Zn y Pb(+/-Au) y proximal de Zn+/-Cu, asociados a cuerpos hipoabisales de composición cuarzoandesítica y andesítica. Estudios y exploraciones recientes muestran otros tipos de sistemas mineralizados, como brechas tectónicas con reactivación hidrotermal tardía, un sistema epitermal de sulfuración intermedia en vetas, cuerpos irregulares, entre otros, y un sistema tipo pórfido. La Falla Milpo-Atacocha, de rumbo N-S, juega un rol importante, ya que los intrusivos (Stock Milpo y Santa Bárbara) que generan la mineralización del tipo skarn están controlados por esta falla. Existe otro tipo de mineralización, asociado al sistema NW-SE (Falla 13): un sistema epitermal de sulfuración intermedia. Este trabajo pretende mostrar los últimos avances en las interpretaciones metalogenéticas, producto de un intenso programa de exploración (aproximadamente 80,000 m. DDH / 2018) y de un programa de recategorización de recursos (a través de 60,000 m. DDH), que permitirá hacer posible una operación sostenible de 12 años.

May 22, 2019

By R A. Binns, S Murao

The PACMANUS and Jade deposits are two active hydrothermal fields that are forming massive sulphide deposits at the Pacific rim margin. Both are associated with felsic submarine volcanic rocks and both occur in back-arc settings. However, PACMANUS is associated with almost sediment-free dacites and lies on the crest of a volcanic ridge, whereas Jade occurs in a heavily-sedimented tectonic depression associated with a basement of pumiceous rhyolite. The PACMANUS deposit is richer in Cu and Au, and Jade in Pb. Zinc, Ag, As and Sb contents are similar. Sulfide textures at PACMANUS suggest formation of Cu and Zn sulfides by simultaneous double-diffusion involving inwards-moving seawater mixing with outwards-moving hydrothermal fluid. By contrast, at Jade there is a more complex history of formation where initial growth of barite on the sediment surface, probably associated with microbial activity, formed an impervious cap which trapped higher temperature hydrothermal solutions.  

Jan 1, 1995

By Roussos Dimitrakopoulos

Conventional approaches to estimating reserves and optimizing mine planning and production forecasting result in single, often biased forecasts. This is largely due to the non-linear propagation of errors in understanding orebody attributes from a limited finite number of drilling data, throughout the chain of mine planning and mining. A new mine planning paradign is considered herein to include two interacting and potentially fusing elements: stochastic simulation and stochastic optimization. These two elements provide an expanded mathematical framework that allows the modelling of orebody uncertainty and its direct integration to mine design, production planning and valuation of mining projects and operations. This stochastic framework has shown to increase the value of production schedules in the order of 25%. In addition, case studies show that stochastic optimal pit limits are about 15% larger in terms of total tonnage, compared to the conventional (deterministic) optimal pit limits. This difference extends life of mine and adds approximately 10% of net present value (NPV) to the NPV reported above from stochastic production scheduling within the conventionally optimal pit limits. Furthermore, results suggest a potential new contribution to the sustainable utilization of natural resources.

Oct 1, 2009