Search Documents

By A. Bruynesteyn

It is well known that most North American gold deposits are of a hydrothermal origin and therefore they are often associated with sulphide minerals such as pyrite and arsenopyrite. When the precious metals in such ores are held captive inside sulphide crystals, the ores are called refractory because they do not respond to treatment by direct cyanidation. In these cases, it is necessary to recover the contained precious metals using high temperature treatments such as smelting or roasting, or high pressure leaching processes to break down the sulphide crystal matrices and thus liberate the precious metals for subsequent extraction by cyanidation. Sulphidic gold ores containing arsenic and/or antimony are considerably more difficult to treat because, in addition to their refractory nature, the arsenic and antimony content also prohibits treatment by direct cyanidation or amalgamation. These ores must be milled and their sulphidic gold values concentrated by flotation. The resultant concentrates must then be roasted to break down the sulphides before cyanide treatment can be applied.

Jan 1, 1985

By R. Y. Wan, J. D. Miller, P. L. Sibrell

Three different refractory carbonaceous gold ores from the Carlin operation in northeastern Nevada were investigated to characterize the effect of passivation treatments on the nature of the carbonaceous material. The carbonaceous material was chemically isolated from the ores and passivated residues, and examined by FTIR spectroscopy, elemental analysis, and gold adsorption capacity. The main component of the carbonaceous material in these ores was found to be a naturally occurring activated carbon-type compound. Hydro-carbons were detected on rare occasions, but no evidence was seen for humic acids. Ore samples were passivated by autoclaving, or by treatment with sodium hypochlorite or gaseous chlorine. In some of the passivation tests, a new peak was observed in the IR spectra of the isolated carbonaceous material, that was due to carbonyl functionalities. However, all of the passivation treatments tested decreased preg robbing significantly. This suggested that the appearance of the carbonyl peak was due to the severity of the conditions during passivation, rather than the method used.

Jan 1, 1990

By Norman Brown, J. V. Rinnovatore

Substructures in explosively deformed and annealed ß brass have been examined by electron microscopy. In the explosively deformed condition, the structure contains a large density of straight screw type dislocations. Subsequent annealing up to 300oC produces low angle boundaries, which are characterized by superlattice dislocations, and expanded and contracted nodes. Evidence is given where two a(111) superlattice dislocations combine to form two a(001) superlattice dislocations. It is also shown that annealing at 400°C the networks disappear and that quenching from 400" C produces square and circular prismatic dislocation loops that lie on (100) and (111) planes, respectively. THE purpose of this work was to determine the effects of explosive deformation and subsequent annealing in a superlattice using electron microscopy. One of the first observations of explosively deformed structures was made by Hornbogen1 on a iron. Hornbogen found that screw dislocations were most prominent in the explosively deformed structure. He explained this result by suggesting that the edge components of dislocation loops move with the velocity of the shock front leaving a trail of extended screw components. Kressel and Brown2 observed explosively deformed Fe3A1, which is basically a body-centered type of superlattice in terms of dislocation geometry, and found that, as in the case of iron, screw dislocations were most prominent. It was also observed2 that, in cold-rolled and explosively deformed nickel, screw dislocations did not predominate, but rather a uniform network of dislocations was present in which the orientation of the dislocations was random. (Cell structures also have been observed by Nolder and Thomas3 for copper and by Johari and Thomas* for nickel). Kressel and Brown2 discussed the difference between dislocation morphology for bee and fee metals in terms of dislocation mobilities. They suggested that edge dislocations have a greater mobility than screw dislocations in bee metals but not in fee metals. Thus, the idea offered originally by Hornbogen1 is not valid since it should apply equally to fee and bee systems but does not. The results of recent work by Mikkola and cohens on explosively deformed Cu2Au are consistent with other observations for fee metals. They found that dislocations were randomly arranged but there was no significant cell formation. At high shock pressures, deformation twins are produced in fee metals.' High pressures in bee metal should induce the bee — fee transformation while the metal is under pressure. EXPERIMENTAL PROCEDURE The Cu-Zn alloy used in this work contained 51.4 wt pct Cu. Specimens of 0.5 in. diam and 0.012 in.

Jan 1, 1968

Improve ground control in longwall gate entries by developing a practical method for evaluating longwall pillar designs. Background Longwalls have emerged as the most important technology to be applied to underground mining since the continuous mining machine. Longwall mines currently produce more than 30 pct of all the underground coal mined in the United States, up from less than 5 pct just 15 years ago. Safe longwall mining depends on maintaining ground control in the gate entries, the lifelines that provide access to the longwall face. In multientry retreat mining as practiced in the United States, rows of chain pillars are left to protect the gate entries (see figure 1). Chain pillars are subject to severe and complex abutment loads during the process of longwall panel extraction. The design of these pillars is often the single most important element in gate entry ground control and has been the subject of intensive Bureau of Mines research.

Jan 1, 1991

Minerals similar to the indicator minerals used in kimberlite exploration are widespread in the Cainozoic alkali basalts of north Queensland. Magnesian ilmenite, pyrope garnet, chrome diopside, chrome spinel, phlogopite and zircon were recovered from most of the localities examined. The occurrence of these minerals creates significant problems when indicator minerals are used for diamond exploration. Basaltic ilmenite is visually similar to kimberlitic ilmenite. Untransported grains are rounded and have pitted surfaces. Basaltic ilmenite grains often have exsolution lamellae and reaction rims of titanomagnetite. Although kimberlitic and basaltic ilmenite are chemically similar, basaltic ilmenite grains are usually less magnesian than their kimberlitic counterparts. Basaltic ilmenite contains very little Cr203. Pyrope garnet occurs as megacrysts and in a variety of xenolith lithologies in north Queensland basalts. Most basaltic garnet is Cr-poor and comparable with kimberlitic garnet from Groups 3 and 5 of Dawson and Stephens (1975). Wine-purple, chrome-bearing garnet is common in kimberlite but rare in basalt.

Jan 1, 1984

Iron Concentrate Synthesised from Waste Ferrous Sulfate Produced in Titanium White Preparation

Sep 13, 2010

By Hakan Gurgenli

Many coal seams have weak shale immediate roofs that cause ground control problems. Therefore, it is important to know the properties of these shales so that preventive measures can be developed in advance. However, it is sometimes hard to understand this rock type due to its unpredictable behavior. A good example of this situation is found in two shale coal mine roofs located in the Illinois coal basin (Herrin No. 6 seam). Although, these mines are located very close to each other, one of them has many roof falls, whereas the other has no measurable ground control problems. The aim of this paper is to explain why and how one shale roof behaves worse than the other. Laboratory tests, including point load strength index, slake durability index, moisture activity index, weatherability index, water content determination, swelling strain and x-ray diffraction tests were performed to analyze the shale properties. According to these analyses, some useful correlations were found between the engineering properties, moisture-sensitivity indices, and weathering properties. Finally, mine and support design considerations based on the test results were discussed and recommendations to prevent ground control problems were given.

Jan 1, 2006

By Jesús Ylazaca

El presente trabajo describe el método de control de calidad del mineral o el denominado "Ore control", realizado en la unidad minera Yauli, cuya finalidad es maximizar el valor del mineral minado para lograr una mayor rentabilidad. En este sentido, el "ore control" es la gestión que optimiza las diferentes etapas de la exploración, explotación y concentración del mineral para lograr una buena calidad de producto (concentrados), a fin de satisfacer las necesidades del cliente. Los controles involucran a la Gerencia y el total de supervisores y trabajadores de operaciones, quienes deben ser proactivos ejecutando acciones preventivas más que correctivas.

Sep 12, 2005

By Reuter M. A., R. D. van der Weijden, W. F. C. van Wageningen

"Copper(II) can be recovered or removed from acidic copper sulfate solutions as cuprite or metallic copper powder by reduction with carbohydrates. The copper powder characteristics, such as size and shape of particles, determine the tendency to adhere to reactor walls and to agglomerate. In order to make this process suitable for a commercial scale pipe reactor, process conditions and the reactor configuration were varied in order to influence the copper characteristics in a positive way. The aim was to achieve proper particle throughput in the pipe reactor and to obtain a well defined copper powder.In this paper the effect of both, chemical and physical parameters on the shape and size of particles were systematically studied in a number of autoclave experiments. These parameters include mixing, Cu(II) concentration, pH, temperature, seeding, use of additives and reactor materials. Additionally, Monte Carlo simulations of copper growth inside a Kenics static mixer were made. Results show that the use of additives and the use of static mixers influence particle characteristics the most."

Jan 1, 2003

By Launa G. Mallett, Charles Vaught

This report is intended to help mine safety trainers better prepare to teach the influx of new underground coal miners who are entering the industry. This is done by identifying two different approaches to instruction and discussing the ways they may affect how well prepared new hires are to deal with a dynamic and hazardous workplace. One approach is based on the use of a syllabus. Those using a syllabus are more likely to rely on lecturing or direct instruction. This is a good way to get across factual information, but does not provide a context within which miners can fit the discrete facts so that they form an integrated whole set of concepts, principles, and skills. The other approach is based on the use of a curriculum. Those using a curriculum may be more likely to help miners integrate concepts and skills that give them an overall picture of the complex mining environment and how they fit into the workplace. This will better prepare them for the decision-making and problem-solving activities that will help them work safely and productively

Jan 1, 2008

By A. C. Burrow, R. P. King

A dynamic model that predicts the variation of carbon content with time in the argon-oxygen decarburization (AOD) process has been developed. The model recognizes three distinct zones in the AOD vessel: the tuyere region in which the blown oxygen reacts very rapidly with the metal components in the molten alloy; a region in which bubbles of inert gas and oxide drop lets rise through the molten alloy; and a zone in which the slag layer can interact with the molten alloy. The process is dynamically controlled by the rate at which dissolved oxygen, produced on the surface of rising oxide droplets, and dissolved carbon diffuse through the molten alloy to react at the surface of the rising bubbles. The rate at which carbon and oxygen react on the bubble surface is assumed to be intrinsically very fast. Predicted decarburization rates compare reasonably well with rates measured in the AOD vessel at Middleburg Steel and Alloys. The model has been developed primarily to allow development of a time-optimal blowing stategy for the AOD vessel.

Jan 1, 1990

By Aspinall T. O

Draglines have found wide application in strip mining coal seams down to 60m depth. A research Project funded through NERDDC has been underway during the past two years investigating the application of large draglines loading overburden into hoppers feeding into conveyor systems or off-highway trucks. This paper presents the preliminary results of these investigations and covers overburden characteristics, bucket spotting con- trol, bucket design, conceptual hopper systems, system application at representative mine sites, and broad process comparison. The studies have initiated new concepts in the extended use of draglines at deeper strip- ping depths. Alternate arrangements for dragline bucket rigging and bucket control aspects of dragline stripping operations offer productivity improvements. Extended use of existing draglines includes, draglines dumping into hoppers which feed large trucks or conveyors, trigger dump buckets rigging arrangements, and rear dump dragline buckets with integral grizzly bars. The paper details these suggestions, and points to specific areas where the most productive applied research is anticipated. Mine planning considerations detail the factors involved in selecting dragline bench heights in association with hopper operations.

Jan 1, 1989

By B Wiggins, M Russell

Off-gas handling systems are a critical component of modern metallurgical furnaces and typically represent as much as 50 per cent of the total installed smelter capital cost. Inadequate off-gas system performance, due to insufficient exhaust flow or excess maintenance downtime, can present a serious process bottleneck and limit smelter production rate. Therefore, it is essential that the relevant performance issues are fully understood and considered in the design of these systems, particularly when combustibles produced within the furnace must be combusted or handled in the off-gas system. This paper examines the requirements, design issues, and conceptual design process for state-of-the-art postcombustion off-gas systems. The relevant design considerations of safety, environment, energy consumption, and maintenance are presented, and the relative importance of these key issues are compared and discussed. The benefits of using computational fluid dynamic (CFD) modeling in the design process at the conceptual design stage are also demonstrated. Finally, the design basis and performance of a recent Hatch-engineered system currently in operation is evaluated.

Jan 1, 2002

By Shosei Serata, Bruce Gardner

A system of three new field instruments has been developed to measure, in situ, the three basic classes of geomechanical parameters: material properties, stress state, and creep deformation. The significance of this development is that it represents a successful adaptation of recent computer technology to underground rock mechanics work, opening up new possibilities in underground mining methods. The system was developed to meet the application requirements of the stress control method of mining, a method which is based on the actual geomechanical conditions of the underground, rather than upon conventional linear-elastic, idealizations of ground conditions. These instruments enable in situ measurement not only of elastic, but also post-elastic, yielding, and failure conditions of geological materials, establishing the stress control method on a truly scientific foundation. In order to evaluate the present status of this field instrumentation system, case examples of underground mine openings designed with the stress control method are reviewed and analyzed, in terms of the effectiveness of the three instruments for informing and guiding the site-specific application of stress control design.

Jan 1, 1984

By Joseph A. Sutton

The prospect of utilizing bacteria in mining and metallurgical processes introduces a new and challenging area of investigation. Elements of bacteriology and metallurgy are discussed in connection with possible areas where biological science might be applied in extractive metallurgy. Bacteria may prove important in the selective separation of metals from ores and metallurgical solutions, the production of sulfur from gypsum or pyrites, and the production of sulfuric acid from elemental sulfur. A series of reports concerning the experimental applications of bacteria on minerals and metallic ores will follow this paper. For several years the Bureau of Mines has been investigating the action of bacteria in the oxidation of sulfide minerals and their potential uses in metallurgical processes. Primary attention has been given to the possible utilization of certain strains of autotrophic bacteria that live in industrial leaching solutions or fractures of mineral outcrops. The purpose of this paper is to acquaint the mining and metallurgical engineer with micro-organisms and some of their possible applications in the field of extractive metallurgy.

Jan 1, 1961

By David C. Laurence

in March 1999, the School of Mining Engineering at the University of New South Wales carried out a series of underground trials using " Evermine", a South African developed two-part water based polymer membrane. The aim of the trials was to determine the potential of a spray-on polymer membrane such as Evermine as an alternative to conventional rib support systems The mine selected was Angus Place colliery, reputed to have some of the worst ground conditions of any Australian underground coal mine. Ribs at Angus Place are supported by conventional pattern bolting supplemented by wire mesh. The trials indicate that there is significant potential for the introduction of polymer membranes into the underground coal minim; industry Initial results indicated that ribs that had been sprayed exhibited less displacement and spalling than unsprayed ribs. particularly when subjected to abutment loads from an approaching long-wall Further research will he required to conclusively rate the performance of Evermine in comparison to other products in the market and the long term performance of the product

Jan 1, 2000

By Robley D. Evans, Gerald L. Schroeder

Advanced techniques for control of radon (Rn) daughter product concenrrations (working levels, WL) in the uranium mines are discussed. Understanding the physical laws which govern the flux of radon into a mine, the growth and decay of the radon daughters, and the particulate nature of the daughters when suspended in air allows ventilation personnel to improve the quality of mine air with no increase in ventilation rate. The task of controlling, in a mine atmosphere, the short-lived nuclides produced in the decay chain of radon is a unique problem and as such should be approached with ventilation techniques specific to the problem. For most mines this has not been the case. Rather, procedures for removing these airborne radioactive nuclides have been borrowed directly from ventilation experience in mines where dilution ventilation was the traditionally accepted approach for air purification. With radon daughter products, this has often led to frustrating difficulties and expense. Primary origin of the airborne radioactivity is the a-ray-emitting noble gas, radon (222Rn, Rn), a nuclide formed by the decay of radium (226Ra, Ra). Radon, being a gas, may escape from its parent crystal and diffuse through the parent mineral into the interstices of the rock body. In a sandstone structure, about 20% of all the radon formed may find its way into the interstices of the rock. If a cavity such as a mine is nearby, the radon may diffuse through the rock interstices into the mine. While radium is usually highly concentrated in uranium ores, it is also found in varying concentrations in all minerals. Radon is therefore present in all minerals. In normal glacial till, the equilibrium interstitial radon concentration often equals 5000 pCi (picocurie, also uuCi) Rn per liter of pore volume.' In normal granitic rocks, the interstitial radon concentration often approaches 30,000 pCi per 1. Considering these typical, high-radon concentrations, radioactivity from airborne of daughter products is a potential problem unique not only to the uranium mining industry and should be considered as a potential hazard in all underground environments.

Jan 1, 1970

By Per-Anders Persson

This chapter deals with the concepts of shock wave8 and detonation wavea together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the context of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of an explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of thii chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1998

By M. Schwartz, S. K. Nash, R. Zeman

Knoop hardness in the rolling plane and in the longitudinal plane of hot-rolled and cold-rolled sheets of sublimed magnesiu?w was measured as a function of the angle between the long axis of the indenter and the rolling direction. These measurements were correlated with similar data taken on the (0001) and (1010) planes of a single crystal of magnesium where the hardness was measured as a function of the angle between the long axis of the indenter and the [1120] direction. The results were analyzed for compliance with the hypothesis of Daniels and Dunm to account for slip, and with a similar hypothesis to account for twinning. Some hardness anisotropy data are also presented for magnesium-indium and magnesium-lithium solid solution alloys. It is well known that the hardness of a crystalline specimen is different for its different surfaces, and also that the hardness is a function of direction within a single surface. Variations in hardness for single crystals have been found to be much larger than those for polycrystalline materials. Also, materials having low crystal symmetry were found to have a greater anisotropy of hardness than those of high symmetry. 0'Neill1 and Pfeil,2 using a 1-mm Brine11 ball, studied single crystals of aluminum and iron, respectively; and they found a variation of hardness of about 10 pct between readings taken along the principal crystallographic faces. Daniels and Dunn3 found that the Knoop hardness number varied about 25 pct as the long axis of the indenter rotated on the basal plane of a zinc single crystal. The variation on the (1450) plane was about 100 pct, and the average hardness on this plane was about twice that of the basal plane. They also studied the variation of hardness within the (loo), (110), and (111) faces of a single crystal of silicon ferrite and found variations of about 25 pct although the average values for these planes were almost identical. Single crystals of zinc were also studied by Meincke.4 He found that the Vickers hardness numbers varied about 30 pct depending on whether the axis of the indenter was parallel or perpendicular to the (1010) and (1110) planes. Mott and Ford,5 using a Knoop indenter, found a 25 pct variation in hardness on the basal plane of zinc. Crow and Hinsley6 studied heavily cold-rolled bronze, steel, brass, copper, and other metals. They found that the difference in hardness numbers based on the difference in the length of the diagonals of the Vickers indenter was from 5 to 12 pct. Some minerals and synthetic stones show a very large anisotropy of hardness. Robertson and Van Meter7 found the Vickers hardness of arsenopyrite to vary from 633 to 1148 kg per mm2. stern8 using the double-cone method on synthetic corundum found the hardness number to vary from 950 to 2070. And winchell9 reported a variation of hardness number from 184 to 1205 in kyanite. The variation of hardness as a function of direction in a given crystallographic plane in single crystals possesses a periodicity which is related to the symmetry of the lattice. Daniels and Dunn3 found a six-fold periodicity of hardness in the (0001) plane of zinc. They found that the hardness curves of silicon ferrite had a four-fold symmetry in the (100) plane, a two-fold symmetry in the (110) plane, and a six-fold symmetry in the (111) plane. Mott and Ford5 also reported a six-fold symmetry of hardness in the basal plane of zinc. And vacher10 found two-, four-, and six-fold periodicities of hardness in copper on the (110), (100), and (111) planes, respectively. The purpose of this paper is to report the results of an investigation on the anisotropy of hardness as a function of orientation in single crystals of mannes-ium, and samples of rolled magnesium, magnesium-indium, and magnesium-lithium solid solution alloys. The anisotropy of hardness of pure magnesium which had been hot rolled, and then cold rolled various amounts to fracture, was studied by means of Knoop indentation hardness numbers; and the results were correlated with the preferred orientation as determined by quantitative X-ray pole-figure data. A comparison was made of the hardness data obtained from the rolled sheets and those of single crystals of magnesium. In order to obtain a more fundamental understanding of the variation of hardness and of Knoop hardness testing, the data were analyzed by

Jan 1, 1962

By Charles E. Whieldon

Because of the importance of recovering more oil from known petroleum reserves, increased emphasis has been placed on the application of secondary-recovery methods. It is hoped that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases. Previously published reports3 4 5/ have described the results of water-flooding in Roane, Pleasants, and Wetzel Counties, W. Va. (fig. 1). This report describes the South Penn Oil Co. Yawkey waterflood property, Berea sand, Griffithsville oilfield, Duval District, Lincoln County, W. Va. (fig. 2).

Jan 1, 1961