Search Documents

By Robert Bakish

VARIOUS aspects of structure-sensitive corrosion of single crystals and polycrystalline aggregates of Cu,Au have been presented in papers by the author, in association with W. D. Robertson. Prompted by some observations in the course of these studies, a new approach to the problem was undertaken. Results of these new experiments are reported here. Thin slices, less than 2 mm thick, were prepared from single crystals 3.5 mm in diam grown by the Bridgman technique. The crystals were homogen- ized for 300 hr at 850°C. Crystals with no deformation, crystals deformed in tension to the yield point, and crystals deformed 20 pct in excess of the yield point were used. Crystals of several different orientations were studied. Slices were immersed for one month in 2 pct aqueous solution of FeCl3 and, subsequent to this immersion, were subjected to bending. Immersion and bending were carried out at room temperature. The size and geometry of the crystals did not permit accurate data on the loads involved. A most unexpected result was obtained in the process of bending these slices of Cu3Au crystals normal to the (110) plane. Completely brittle be-

Jan 1, 1958

By Harrison Schmitt

IN the practice of ore finding the geologist is continually confronted with the question of oreshoot extension, so that the general problem seems worthy of systematic investigation. This problem appears when the reserves are estimated and when the advisability of deepening the shaft comes up. Moreover, there is need for lower development cost to keep pace with cost reductions in other departments, or even to offset a rising cost of ore finding or ore following. This can be gained by close geologic control of the development; and much of the geology involved is that bearing on the downward, upward, and horizontal extensions of shoots. Furthermore, the purchase of a mine or prospect often depends directly on the question of shoot extension; because it is seldom that the ore is fully developed and the purchase price is almost invariably based largely on "possible" and geologically prospective ore. Most current methods for estimating "possible" and the more nebulous classes of ore are crude and indecisive. In the following pages the extension of oreshoots is the major theme, although the more basic subject, the general art of ore finding, is given some space.

Jan 1, 1929

By J. Shibata

The recovery process of valuable metals, such as Ll, Mn, Ni and Cr from a waste lithium battery was developed n this study. Lithium and Mn are selectively leached from the battery by using dilute mineral acid. Main part of the battery comprises stainless steel, and Fe, Ni and Cr are easily leached by the mixture of dilute HCl and HNO3 Lithium and Mn are precipitated as metal carbonates from the? individual leached solution with sodium carbonate solution. The solution containing Fe,Ni and Cr Is treated by solvent extraction to separate NI and Cr from the leached solution. The experiments are carried out for leaching and separation steps. According to the experimental results, the flow. sheet for a recovery process of valuable metals from a waste lithium battery has been established.

Jan 1, 1995

By K. Takahashi, I. Iwasaki

The methyl stretching vibrations for a series of normal xanthates, isoxanthates and normal amines were determined with the aid of an infrared spectro-photometer, and the results were compared with published information on the corresponding alcohols. The frequency shifts of methyl stretching vibrations may be attributed to the inductive effect of polar groups. The hydrogens in the shorter chain alkyl groups are somewhat polar and can be expected to interact with water molecules by hydrogen bonding. Contact angle, surface tension lowering, solubility, and critical micelle concentration appear to be related to the induced polarity of the alkyl groups. Traube's rule states that in homologous series of compounds solubility decreases and surface activity increases regularly with the size of the hydrocarbon group. Analyzing the work of transfer of a solute from solution to surface, Langmuir' interpreted this rule to mean that each CH2 group added to a molecule produced its effect independently of the others. It is also well known2 that the maximum equilibrium contact angle with sulfhydryl collectors is independent of the polar groups and of the sulfide minerals, and that it increases to a certain limit with the number of carbon atoms in the alkyl group. This observation is thought to demonstrate the orientation of the collector molecules at the sulfide surfaces. The dependence on the hydrocarbon chain length is usually explained as due to the screening of the force field of polar mineral surfaces.3-5 Here again, Langmuir's principle of independent surface action appears to be implied. Heteropolar compounds consist of nonpolar and polar groups, the former being the hydrocarbon group and the latter containing such electronegative atoms as O, N, S, P, or halogens. According to Palit6 the hydrogens in the alkyl groups are more electroposi- tive than in the paraffins owing to the negative inductive effect of the polar groups and a possibility that a hydrogen bond with water molecules ensues. Goto and Takenaka7 provided direct evidence of the inductive effect by measuring the shift of the C-H stretching vibrations of alcohols, acids, and alkyl bromides with an infrared spectrophotometer. Their approach appeared to be directly applicable to the studies of surface activity both at air-water and water-mineral interfaces encountered in flotation systems. The present article attempts to relate the C-H stretching vibrations of alkyl xanthates, alcohols, and amines with such flotation chemistry parameters as contact angle, surface tension lowering, solubility, and critical micelle concentration. MATERIALS AND METHODS Normal xanthates from methyl to octyl inclusive and the isopropyl, isobutyl, and isoamyl xanthates used in this investigation were prepared in the usual manner.8 Normal amine hydrochlorides with carbon chain lengths of 1, 2, 4, and 6 were from Distillation Products Industries, of 8 from Archer-Daniels-Midland Co., and of 10, 12, 14 and 16 from Armour and Co. Normal propylamines, pentylamines and heptylamines from Distillation Products Industries were used both as received and as hydrochloride formed by converting the amines according to the procedure described by Li9 Perkin-Elmer Model 521 and 621 infrared spectro-photometers were used to investigate the spectra in the frequency region of 3050 to 2800 cm-' with frequency scale expansion. The accuracy of the frequency readings was within + 1 cm-1. The KBr micropellet technique was used to prepare the xan-thate samples for measurements, and the halocarbon mull technique was used for amines and amine hydrochlorides. EXPERIMENTAL RESULTS Fig. 1 shows the CH3 asymmetric stretching vibrations as a function of the number of carbons in the alkyl group for normal xanthates, isoxanthates and amines. Also included in the figure are data for normal alcohols and isoalcohols taken from the article

Jan 1, 1970

By Franklin J. Hill, Theodore D. Tiemann

Sized fractions of Wisconsin Gogebic taconite were reduced with hydrogen over the temperature range from 600° to 1000°C. In general, the degree and rate of reduction increase with temperature. Particle size has no observable effect except in the smaller fractions at 900°C and above, where reduction is impeded, possibly due to the siliceous nature of the ore. Gaseous diffusion appears to be significant as a rate controlling factor at certain stages. THE depletion of high grade iron ore reserves in the United States has established the need to utilize all available iron ore deposits, both in long range planning and from the viewpoint of national emergency. This has led to extensive research and development in this field. The beneficiation of Wisconsin Gogebic taconite ore has been previously studied by investigators at the University of Wiscconsin, 1 the United States Bureau of Mines,, Battelle Memorial Institute, 3 and others. Methods investigated have included concentration by flotation processes, magnetic and gravity separation, magnetic roasting and various combinations of them. The foregoing studies have been concerned with the production of an enriched ore suitable for blast furnace use. If the ore could first be reduced to metallic iron and then beneficiated, the product could be used directly in the open hearth or electric steel-making furnace. The by-passing of the blast furnace should enhance the economic feasibility of the beneficiating process. The work reported here,4 was undertaken to establish data on the hydrogen reduction of Wisconsin taconite that would eventually lead to the development of an economic direct reduction process for this and perhaps other low grade siliceous ores. The volume of work on direct reduction can be judged by the fact that 240 direct reduction processes were patented in the United States alone up to 1951, 5 and numerous additional processes have since been developed. Some of the factors contributing to direct reduction development are: 1) The increasing capital cost of the blast furnace and its accessory equipment. 2) The decreasing availability of high grade domestic ore. 3) The high cost of steel scrap for use in the open hearth and electric furnaces. In general, direct reduction processes can be divided into two types; those using a solid reductant (coal, peat, lignite) usually carried out in a kiln, and those using a gaseous reductant (H2, CO) in a shaft furnace or a fluidized bed retort. As there is no low cost coal readily available in northern Wisconsin but natural gas could be quite easily obtained, it is believed a gaseous reductant process would offer the greater feasibility for use on Wisconsin taconite. It is hoped that this preliminary work will beof interest to other investigators in this increasingly important field. TACONITE ORE The ore used in the investigation was obtained originally from the U. S. Bureau of Mines, and consisted of a representative composite made up from trench samples of the Norrie, Pabst, Plymouth, Pence, and Yale members of the Wisconsin Gogebic range iron formation. Chemically, the ore contains approximately 52 pct SiO, and 30 pct Fe. X-ray diffraction and other studies indicate the principal minerals to be quartz (SiO2), hematite (Fe2O3), and goethite (Fe2O3. H2O). Minor amounts of iron containing silicates, siderite (FecO3), and magnetite (FeO-Fe2O3) are present. The iron minerals and quartz are so finely disseminated that the ore requires grinding to less than 200 mesh (74 µ) for essential liberation.l,2 The iron content of each of the several size fractions studied is shown in Table I. EXPERIMENTAL METHOD The method used throughout the investigation was based on that developed by the U. S. Bureau of Mines in Minneaopolis6,7 in which the course of reduction is followed by the loss in weight of the ore sample. More specifically, a 100-g sample of the size frac-

Jan 1, 1962

AT THE beginning of September, the French eased their pressure against Germany and allowed the latter to, be granted an arrangement for its reparation payments in kind according to the Lubersac-Stinnes agreement. The whole arrangement as to the German reparations is, however, but temporary. The Greeks suffered a disastrous defeat at the hands of the Turks in Anatolia, which rapidly resulted in the expulsion of the Greeks from Asia Minor, the Turks occupying Smyrna about Sept. 10. A few days after entering Smyrna the Turks sacked the city and finally set it afire, creating one of the most terrible destructions in history. At the same time their advance on Constantinople, together with their demands on the Allies, brought them directly in, con-flict with the latter and Great. Britain prepared for a new war, with doubt as to the support of France, whose political interests in the Near East are as different as their economic interests with respect to ;Germany. The Turkish situation became thus a threat against the peace of Europe. A revolution in Greece, followed by the abdication of King Constantine and the return of Venizelos to a function in the Government was one of the conse-quences of the defeat in Asia Minor. Civil war continued in Ireland, with more or less -bloodshed. Economically there has been no change for the better in Europe. In Great Britain there, are no signs of an -important trade revival. In Germany and Austria things are worse. French, Italian and Spanish affairs continue in a bad way. In the United States business is represented as "booming," but many people are inquiring where is the boom? About the middle of September Congress passed the tariff and the soldier bonus bills. The President signed the former and vetoed the latter, with a strong message that won praise among people who understand condi-tions. Congress tried to pass the bill over the veto, but failed. The President signed the tariff bill, which became effective Sept. 21. A severe handicap was thus imposed on American economics.

Jan 10, 1922

By Martin C. Kuhn, Lawrence G. Stevens, J. Mark Richardson

The majority of the world's known and anticipated reserves of nickel ores are lateritic deposits At present, there are several different process alternatives for recovering nickel and other desired metal values from laterite ores An overview is given of the selective reduction roast/ammoniacal leach process, one of the processes in commercial operation.

Jan 1, 1981

Procurement of uranium is vital to the future of the Nation. Its utilization for atomic energy can destroy mankind or raise an unsurpassable civilization-the problem of the statesmen. Uranium poses a challenge to the mining profession. Evanescent in occurrence, its discovery and mining can mean substantial profits, plus safeguarding the future of the Nation.

Jan 9, 1951

By James H. Boettcher

In the second quarter of 1979, ASL Inc. inquired whether Crocker National Bank ("CNB") would provide $4 million in term loan financing to help ASL acquire the outstanding shares of the S&S Coal Company in West Virginia. ASL had, prior to approaching CNB, sought financing with the assistance of a financial advisor from a number of commercial banks without success. A summary of the initial terms requested by ASL is shown in Table I compared with the actual terms the transaction closed with. It is not difficult to note that the two sets of terms differ significantly. This is often the case when financing requests based on the expectations and vision of a mine developer are juxtaposed with more pragmatic requirements of a commercial bank. The "art" and fun of structuring financing plans for mining ventures (highly leveraged acquisitions or grass roots) comes in working with mine developers to arrive at a final financial structure that meets their objectives and constraints as well as those of the bank or other financial institution providing much of the financing. This article briefly describes the process we went through with ASL beginning with the terms they requested initially and ending with the ones on which the transaction was finally closed.

Jan 1, 1981

Jan 1, 1969

Beneficiation Studies of Dolomitic Rock Phosphate in Pursuit of Zero Waste Technology - A Case Study

Sep 13, 2010

By A. K. Csazar, L. W. Holm

This paper describes our investigation of a post-water-flood, oil recovery process which consists of injecting a slug of propane followed by water. Also described are the results obtained by applying a modification of the process in which gas was injected ahead of the water. Under the conditions of the latter experiments, misci-bility was not achieved between the propane and gas. Preliminary experiments or) uniform, watered-out sandstone cores showed that an oil bank could be formed and produced by applying this recovery process. However, since reservoirs are not uniform in structure, the process also was applied to porous media containing irregular porosity and to stratified sand systems. As a supplenzerrt to the experinlental work, a mathernatical procedure was developed for calculating the performance of the recovery process in a bounded, layered, porous system with crossflow between layers. As a specific example, the method was applied to predict the perforrnance of the recovery process in a 6-ft long, two-layer, stratified, unconsolidated sand model for comparison with experinlental data. The calculations were programed for the ZBM 704 computer. The equations and calcula-tional procedure presented can be extended to systems containing any number of randomly distributed permeability variations or any number of parallel layers. INTRODUCTION The problem of recovering the oil that remains in a reservoir which has been waterflooded is receiving considerable attention now as an increasing number of water floods reach an economic limit. A large number of the waterflood projects are in shallow reservoirs which are at pressures below 1,000 psi. It has been demonstrated in the laboratory that post-waterflood oil can be recover-ered by miscible displacement, but the LPG-gas, miscible flood and the enriched gas drive cannot be applied effectively at pressures below 1,000 psi. Only a few reports have appeared in the literature2-4 on low pressure, partially miscible recovery methods. However, it is possible to use LPG in a partially miscible displacement process in a reservoir where pressures of 200 to 1,000 psi can be achieved. Under these Pressures and at normal reservoir temperatures, propane is miscible with the oil; but, of course, gas or water used to drive the propane slug would not be miscible with the propane. Because of the lack of complete miscibility, it has generally been concluded that excessive amounts of propane would be required to recover oil and that such a recovery method would not be economical; however, we have found that under conditions present in certain reservoirs, an imrniscible recovery process can be applied effectively. The oil saturation in reservoirs at the economic limit of waterflood projects is usually in the range of 20 to 35 per cent of the pore space." A certain portion of this oil is left trapped by water in various size pores of the rock, but a good part of this so-called "residual" oil can be present in the less permeable lenses or layers of the reservoir rock which were by-passed to some degree by the water. The oil in these permeability traps can be produced only if favorable pressure gradients are formed in the reservoirs between adjacent zones of high and low permeabilities. A low viscosity liquid, miscible with the oil in place, which is driven by water through a stratified or heterogeneous porous system can aid in the development of these favorable pressure gradients. The oil that is released thereby from the permeability traps can be recovered by the subsequent water flood. Studies were made to determine how much oil could be recovered from homogeneous and stratified cores and models, which had been water flooded, by injecting a slug of propane and driving it with water. The effect of injecting a slug of gas ahead of the water was also determined. Most of the work described herein was done with the propane-water combination; unless otherwise specified, no gas was injected. The principal objectives of the investigation were to determine (1) if an oil bank could be formed and (2) what ratio of oil recovered to propane injected would be obtained. A further objective was to develop a method for calculating fluid-flow performance in stratified systems which would account for fluid transfer between zones in hydrodynamic communication but of different permeabilities. THEORETICAL ANALYSIS In a theoretical study of the recovery process, analytical expressions were derived to calculate the pressure distribution, the fluid flux in longitudinal (parallel to layers) and transversal (across the layers) directions, and the fluid distribution at any point in the system. The equations were developed for a two-layer porous system in which it was assumed that the fluids in the system were incompressible and that capillary and gravity effects were

By J. R. Low, M. Gensamer

During the course of an investigation into the drawability of automobile-body sheet steel, it became apparent that certain advantages would be possessed by a deep-drawing steel with a very low yield strength, but almost normal tensile strength, provided a reduction in yield strength could be accomplished without sacrifice of ductility and fine grain size. It would also be desirable to have this steel free from strain-aging; that is, free from the tendency for the yield point to return after it had been eliminated by straining. It was known that, wet hydrogen treatment acted to eliminate aging, but as carried out by other investigators, at relatively high temperatures, this treatment resulted in grain coarsening. It has been established by some of the experiments reported in this paper that all of these objectives can be accomplished by treatment in wet hydrogen at a low temperature, in the neighborhood of 72o°C. The time of treatment is relatively short (about 3 hr, to completion with 20-gauge sheet) if the water content of the hydrogen atmosphere is made fairly high, say aimost 30 per cent by volume. At this temperature. the grain size remains fine in the time required. After this treatment sheet reduced the usual amount by cold-rolling has a grain size of about A.S.T.M. No. 7. The yield point is completely eliminated, and the yield strength is reduced to a very low value, in the neighborhood of 15,000 lb. per sq. in. The stress-strain curve departs gradually from the straight-line elastic part after the fashion of nonferrous deep-drawing alloys. This elimination of the yield point is accompanied by a verv low indentation hardness; for example, 32 Rockwell B or even lower. There is no aging as measured by increase in the yield strength upon aging at room temperature or for 3 hr. at 200°C., after stretching about 10 per cent in tension. Tensile strength is only slightly less than the box-annealed sheet, seldom dropping much below 40,-ooo lb. per sq. in. Elongation is practically unchanged, or increased slightly. The term yield point, as here used, refers to the phenomenon of heterogeneous deformation occurring at a substantiallv constant load, observed principally in annealed low-carbon steels. If such a steel is loaded in tension, the load increases steadily with elastic strain, suddenly falls, fluctuates slightly about some constant value for a time and then begins to rise again as deformation proceeds. The maximum initial load before the sudden drop is generally called the "upper yield point"; the value of the load where deformation proceeds at a

Jan 1, 1944

By J. R. Low, M. Gensamer

During the course of an investigation into the drawability of automobile-body sheet steel, it became apparent that certain advantages would be possessed by a deep-drawing steel with a very low yield strength, but almost normal tensile strength, provided a reduction in yield strength could be accomplished without sacrifice of ductility and fine grain size. It would also be desirable to have this steel free from strain-aging; that is, free from the tendency for the yield point to return after it had been eliminated by straining. It was known that, wet hydrogen treatment acted to eliminate aging, but as carried out by other investigators, at relatively high temperatures, this treatment resulted in grain coarsening. It has been established by some of the experiments reported in this paper that all of these objectives can be accomplished by treatment in wet hydrogen at a low temperature, in the neighborhood of 72o°C. The time of treatment is relatively short (about 3 hr, to completion with 20-gauge sheet) if the water content of the hydrogen atmosphere is made fairly high, say aimost 30 per cent by volume. At this temperature. the grain size remains fine in the time required. After this treatment sheet reduced the usual amount by cold-rolling has a grain size of about A.S.T.M. No. 7. The yield point is completely eliminated, and the yield strength is reduced to a very low value, in the neighborhood of 15,000 lb. per sq. in. The stress-strain curve departs gradually from the straight-line elastic part after the fashion of nonferrous deep-drawing alloys. This elimination of the yield point is accompanied by a verv low indentation hardness; for example, 32 Rockwell B or even lower. There is no aging as measured by increase in the yield strength upon aging at room temperature or for 3 hr. at 200°C., after stretching about 10 per cent in tension. Tensile strength is only slightly less than the box-annealed sheet, seldom dropping much below 40,-ooo lb. per sq. in. Elongation is practically unchanged, or increased slightly. The term yield point, as here used, refers to the phenomenon of heterogeneous deformation occurring at a substantiallv constant load, observed principally in annealed low-carbon steels. If such a steel is loaded in tension, the load increases steadily with elastic strain, suddenly falls, fluctuates slightly about some constant value for a time and then begins to rise again as deformation proceeds. The maximum initial load before the sudden drop is generally called the "upper yield point"; the value of the load where deformation proceeds at a

Jan 1, 1944

By W. C. Peters

From the time of its beginning in the mid-19th century, the American barite industry has had its major development in the eastern and central states. Geologic and economic factors serve to maintain Arkansas, Missouri, and the Southern Appalachian states in the lead position. In earlier days, the major markets for barite were in paint, chemical, and glass manufacturing, and the favored deposits were those which were close to eastern industrial areas; furthermore, the eastern deposits were cheaply mined and required little or no beneficiation. In the last few decades, the use of barite as a weighting medium for muds in rotary oil well drilling has caused a great expansion in the industry, but the marketing picture is still centered outside of the western states-now on the Gulf Coast area where high pressures are common in oil wells. Low cost imported barite, readily available on the East Coast and Gulf Coast, has always been a major marketing factor in the industry. The major barite producing state is Arkansas, with the industry centering about the Magnet Cove area. Missouri ranks second, with production mainly from residual deposits. Several Southestern states are actively producing from residual deposits.

Jan 9, 1958

The characteristics and causes of the spoil pile failures at the Goonyella Mine are described, and research results from investigations of spoil pile instability are discussed. Some effects on spoil stability of the development of deep strip mining projects are considered and recommendations are made for relevant research.

Jan 1, 1981

By F. Hassani, D. O’Donnell, M. Momayez, P. Guevremont

Shotcrete is a practical and economical support system in many Canadian underground mines. Although shotcrete technology has gained acceptance in the mining industry, there are some problems that have emerged with respect to quality assessment and thickness measurement of the liner. This paper presents recent tests performed with miniature seismic reflection technology (MSR) developed and patented at McGill University primarily for thickness measurement of this heterogeneous liner. MSR is also capable of providing information regarding the quality of shotcrete in terms of its mechanical properties such as modulus of elasticity and Poisson’s ratio. Work was performed on site in an underground mine in Ontario, Canada. This paper also presents the results from laboratory tests performed on fiber-reinforced and non-reinforced shotcrete panels that were used to assess the P-wave velocity in both materials. The results of these tests were used in a second site investigation. The NDT thickness measurements showed good agreement with direct thickness measurement such as coring. In addition, the MSR technology has the advantage of being more accurate and more affordable compared to other non-destructive testing (NDT) systems in the market.

Jan 1, 2002

By Stephen R. Iverson

Manganese deposits exist in the Wonder Mountain RARE II area (fig. 1). The manganese mineral is primarily bementite, a silicate. It occurs with Jasper and manganese oxides in tabular or irregular lenses along the contact between red limestone and basalt. There are about 11,000 tons (10,000 t) of indicated sub-economic resources in the northeast part of the study area. Of this, 10,700 tons containing 27.1 percent manganese is at the Apex Prospect and 300 tons averaging 24.8 percent is at the Brown Mule Mine (fig. 1). Another 1,000 tons (900 t) containing 27.0 percent manganese is at the Steel Creek deposit 0.5 mi (0.8 km) west of the area (Wiebelt, 1942, p. 1, 2). Each of these deposits is subeconomic due to small tonnage and high estimated recovery costs. They are in a regional belt of manganese occurrences trending northwesterly through the area. Pardee (1921) reports that manganese ore was shipped from the Triple Trip (Brown Mule) Mine in 1916.

Jan 1, 1982

By Lo-Ching Chang, J. Chipman

The perennial and increasing interest in the chemical behavior of steelmaking slags has led to numerous attempts to formulate the thermodynamic properties of these solutions. The classical view is that of a solution of the component oxides in which certain acidic oxides are more or less completely held in combination with basic or metallic oxides, the nature of the interoxide compounds being derivable from the chemical behavior of the slag or from the mineralogy of a solidified specimen. The known electrical conductivity of slags has pointed to the existence of ions in the solution and a number of attempts have been made to account for the observed facts of slag behavior on the basis of a theory of complete ionization of the solution. It is the purpose of this paper to examine, in the light of ionic theory, a number of recently published series of data on slag-metal and slag-gas equilibria, with the purpose of obtaining a more complete or more satisfactory generalization than has been possible on either of the single bases of simple compound formation or complete ionization. The attempt to formulate the ionic constitution of a complex solution is fraught with many uncertainties. An ion is not something that can be plucked from the solution and examined in detail, nor can its true formula be determined with certainty by any single experimental method. In attempting to express the composition of a slag by various ionic formulas it can be expected that alternative hypotheses of essentially equal merit will present themselves. In the present state of early development of the ionic theory of slags, it may be necessary to make some rather arbitrary choices of ionic formulas in the absence of su- cient information to yield complete certainty. Acids and Bases The classification of slag-forming oxides as acidic or basic apparently dates back into the days of Berzelius. It is difficult to see how the concept could have originated in the early twentieth century when it was fashionable to define an acid or a base as an aqueous solution containing hydrogen or hy-droxyl ions. It is, however, entirely consistent with the modern and more general theory of acids and bases. In this theory, as originally formulated by G. N. Lewis,' a basic molecule is one that has an electron pair which may enter the valence shell of another atom thus binding the two together by the electron-pair bond. An acid molecule is one which is capable of receiving such an electron pair into the shell of one of its atoms. The acid, the base, and the product of neutralization may be either ions or neutral molecules. The product of such a reaction may itself be a base or an acid if it is further capable of giving or accepting an electron pair. Thus a base is a donor of electrons, an acid, an acceptor. In oxide slags the typical and ever-present base is oxide ion, 0-—. In behavior and in importance it is analogous to hydroxyl ion, OH-, which is the typical base of aqueous solutions. There is nothing in the chemistry of slags which is quite analogous to the acid H30+ in aqueous solutions. This is not surprising for in slag systems there is nothing which can be designated as a solvent and no ubiquitous positive ion. The chemistry of slags is in fact more complex than the chemistry of aqueous solutions and the concepts which must be evoked in its study are correspondingly broader. In seeking a basis for a classification of slag-forming oxides as basic or acidic it must be remembered that these terms are not absolute but relative. A substance which acts as a base toward a second substance may act as an acid toward a third. This is less likely to happen among strong bases or acids than among the weak ones; there are numerous examples of weak acids which under the influence of a stronger acid behave as weak bases. Such substances are called amphoteric. A classification of the glass-forming oxides has been proposed by Sun and Silverman² and further developed by Sun3 in which the oxides are arranged in order of decreasing acidity or increasing basicity, each substance being potentially capable of acting as an acid toward substances below it in the list and as a base toward those above it. It is based upon the relative strengths of the metal-to-oxygen bond as determined by the energy required to dissociate the oxide into its component atoms.' Data are available for computation of this energy, at least approximately, for the oxides of slags and glasses. In general those oxides from which it is most difficult to remove the positive atom are the strong acids while those in which it is most loosely held are the strong bases. It is in the latter, of course, that formation of oxide ion occurs most readily as, for example, in CaO which in solution ionizes to form the weak acid Ca++ and the strong base O—. The order of arrangement found by Sun is shown in the first column of Table 1, to which have been added the data for

Jan 1, 1950

By AIME AIME

I N JUNE, 1918, at a meeting of the American Society of Mechanical Engineers in Worcester, Mass;, a resolution was adopted for a committee to investigate the aims and organization of that society. This was followed subsequently by similar independent action on the part of the Society of Civil Engineers. The other two Founder Societies were approached and requested to appoint similar committees, the four committees to combine as a .Joint Development Committee, later called the Joint Conference Committee, to investigate what might be done in the way of coordinating those activities of the Founder Societies which ape of common interest, and which were then being pursued separately. The Joint Conference committee worked diligently -for almost. two years and. brought forth a tentative as outlined in its report which was published in full in MINING AND. METALLURGY, December, 1919. It recommended the formation of a nation-wide organization to be composed of representatives' of all of -the engineering societies, local, state, regional, or national, the object to be to further the interest of the public through the use of technical knowledge and engineering experience, and to consider and act upon matters common to the engineering and allied technical professions. Whereas the technical societies have large fields of endeavor in welfare work, and their prime. efforts are 'still in technical lines, this new organization was to be devoted entirely to service, looking to the welfare of the nation and the engineering profession, and to service for the public in local and state affairs.

Jan 1, 1920