Search Documents

[ ]

Jan 1, 1991

The high cost of sampling systems is largely due to the fact that indiv- idual mechanical type sampling units must be installed at the discharge end of ore/pulp pipelines, that is, at points where the pipeline discharges into pump sumps or the like. A considerable economic advantage may be obtained in the use of a samp- ling device that can be installed at any point in the path of the trans- porting pipe line. Initial tests on a vertical line with an injection sampler using iron ore concentrates reveal the validity of this type sample versus that taken with a mechanical sampler. A descrip- tion of the injection sampler shows its simplicity of installation, requir- ing minimum downtime on existing lines.

Jan 1, 1976

By Donald P. Tuchman, Robert P. Vinson, Linda J. McWilliams, Steven E. Mischler, Jon C. Volkwein

A personal dust monitor (PDM) was developed to measure respirable coal mine dust mass to provide accurate exposure data at the end of a work shift. Additionally, the new monitor continuously displays near-real-time dust exposure data during the shift. The PDM uses a tapered-element oscillating microbalance to measure the mass of dust deposited on a filter and continually displays the cumulative exposure concentration data. The accuracy and precision of the instrument was determined by comparison to gravimetric filter samplers in the laboratory and in four mines. Laboratory results with different coal types and size distributions showed that there is a 95% confidence that the individual PDM measurements were within ±25% of the reference measurements. Mine test results indicate that data taken with adjacent PDM and reference samplers are indistinguishable. The technology proved durable enough to successfully measure 108 shifts of data out of 115 attempts in the mines. Under these specific test conditions, the PDM demonstrated that it was convenient to wear, robust, provided accurate data, provided timely data that could be used to prevent overexposure, and was easy to use.

Jan 1, 2004

By Marty Hudyma

Mining-induced seismicity and rockbursting is one of the primary risks in deep mines. Seismic data management software has been created to facilitate analysis of mining-induced seismicity. The Mine Seismicity Risk Analysis Program (MS-RAP) is a purpose built database with mine seismicity analysis tools. One of the primary features of MS-RAP is the creation of seismic hazard maps in quasi-real time. The seismic hazard maps identify areas that are more prone to large seismic events and rockbursts, allowing risk management measures to be focused on the areas of greatest risk. These maps allow mining engineers to be more proactive about identifying and managing seismic related geomechanics risks in mines.

Oct 1, 2009

By Nichol R

- PART A The Hoppers Crossing Pumping Station is one of the principal components of the Western Trunk Sewer Project which replaces the 90 year old Main Outfall Sewer and will convey 60% of Melbourne's sewage flow from Brooklyn to the Board's Farm at

Jan 1, 1987

The estimate of an ore reserve is a vital statement made about a mineral occurrence by an evaluator. It is important that such a statement communicate reality to all groups involved in a mining project, be they technical, financial, company directors, Stock Exchanges or the public. Ore reserve statements should state both resources and recoverable ore reserves. Resources may be important in very long term considerations, (because mining, metallurgical technology and economics change with time) but recoverable reserves are todays reality. The important factors contributing to recoverable reserves (in a general sense) are geology, mining method (and its impact on dilution and ore loss), metallurgical recovery, costs and commodity prices. These all need to be reflected in the ore reserve statement. In this paper recoverable ore reserve concepts across a wide range of orebodies are considered and discussed with respect to geology, mining method and ore reserve calculation procedures.

Jan 1, 1987

Structural geological modelling is a process which results in a 3D computer model that represents the essence of the geological and structural understanding of an area and is presented in a way that is directly useable, typically by internal customer groups. BHP Iron Ore operates a number of open cut iron ore mines in the Pilbara Region of Western Australia. The largest mine is the Mt Whaleback Mine located at Newman close to the southern margin of the Pilbara Craton. The structurally complex Mt Whaleback Mine is the largest metalliferous single pit open cut mine in Australia with over 1.6 billion tonnes of original iron ore resource. Additional to the Mt Whaleback Mine, a number of satellite open cut iron ore mines are operated by BHP Iron Ore (BHPIO) in the Newman area. BHPIO also operates the Yarrie mine approximately 400 km north of Newman at the northern edge of the Pilbara Craton Most of the BHPIO mines are located in the Archean- Proterozoic Hamersley Province that overlies the Archean granite-greenstone terrain of the Pilbara Craton. The orebodies are considered to be the result of supergene enrichment of the approximately 2.5 Ga Brockman Iron Formation and the slightly older Marra Mamba Iron Formation. Folding represents the most prevalent and penetrative structural element in the Newman area. Four folding phases have been identified regionally (Fj, F2, F3, F5), while a more local folding deformation (F4) developed mainly in the Mt Whaleback and Orebody 29 mine area. A northeast trending, southeast dipping, 45 km long, high angle, normal fault zone, the Whaleback Fault Zone, cuts through the Mt Whaleback mine resulting in an approximately 1400 in gap in stratigraphy. Additionally, two large, low angle, normal faults, the East Footwall Fault and the Central Fault, are present at the Mt Whaleback Mine. During the formation of supergene orebodies, up to 40 - 45 per cent volume loss occurred resulting in local non-tectonic deformation in the orebodies.

Jan 1, 1997

By Elliot Rexford

The quality of aggregate materials is of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 3, 1950

By M Castle, D Mendelawitz

The Marra Mamba iron ore in FortescueÆs Chichester Range project area occurs as a very flat dipping series of waste shale and iron ore beddings. These beddings vary from millimetre thickness to several metres. The ore material generally exhibits a moderate degree of competence when subjected to ultimate compressive strength (UCS) tests, normally failing at up to 60 Mpa. However, the strength of the beddings is markedly less when subjected to the tensile forces imposed by the cutting action of the surface miner. Two surface miners of differing age and sizes were tested over a period of almost three months. These machines produced a product that had not been subjected to dilution by blasting and of such a size that primary crushing is not required. The machines were able to cut all ferrous material presented to them with varying degrees of success. Material containing higher quantities of manganese were broken but caused catastrophic wearing of the picks. During the trial the volume of material produced by the two machines in various strength materials very closely matched the manufacturerÆs estimates. The major impact on costs per tonne related to the wear on bits, which in turn varied with the bit design and composition. Bit design and composition testing is continuing.

Jan 1, 2007

By N. S. Keith

No one of the live subjects of the day, to which the attention of the mining engineer and metallurgist should be turned, is of greater practical interest to him than electricity in its applications to various mechanical, chemical, and metallurgical operations.. The object of this paper is to call the attention of my fellow-members and associates of the Institute to various new, as well as comparatively old, developments in the science and art of electricity which seem to promise results of advantage. Too many of the comparatively old applications have been neglected by the mining engineer, which, if he had given them a place among his appliances, would have assisted him greatly. The telegraph may be noticed as one. Its use is, however, confined to a person having skill in the manipulations of the key, the reading of the alphabet, and familiarity with the sounder. One of the simpler forms—the call-bell—has a range of application far greater as to distance and convenience than the old wire-pull, or the hoarse voice of the windlass-man or the bucket-dumper. A few Leclanche cells, two or more electric bells, and a mile or more of mire judiciously placed will put the superintendent, at his office, in communication with the foremen of his mills and mines, so that by the aid of a code of signals, great advantages may be gained without necessitating a knowledge of the Morse alphabet, or of the mechanical voice of the sounder. The telephone furnishes a means of communication be-

Jan 1, 1882

By J. H. Huang

In this investigation, the selective precipitation of cobalt and molybdenum from Co-Mo aqueous solutions was studied in order to recover efficiently valuable elements from industrial effluents generated from a novel electrodeposition of nanocrystalline Co-based alloys process and reduce the effluent impact on environment. It was found that the behavior of cobalt in aqueous solutions was substantially affected by the presence of molybdenum. When adding 11.6 to 46.6g/L molybdenum to a 50g/L cobalt solution, the co-precipitation of molybdenum and cobalt started to occur at pH value of 3-4. However, without the presence of molybdenum, cobalt could only be precipitated out of the solution at about pH 6. Most of the molybdenum was found in the solid phase when the solution pH reached 5. After further increasing pH to greater than 7, the molybdenum dissolved back into the solution. Cobalt kept precipitating as the pH increased. When the pH was greater than 7, most of the cobalt was present in the solid phase. The chemical and physical characteristics of the precipitated materials were investigated by SEM, XRD, AAS and EDX. It was revealed that the precipitate was initially present as cobalt molybdate oxide hydrate and subsequently transformed as sodium cobalt molybdenum oxide. With further increasing the solution pH, the precipitate was transformed into cobalt hydroxide. Further investigation implied that most of molybdenum was chemically tied to the precipitate produced at the low pH, yet at the same time, physically entrapped at the high pH. The paper also presents the influence of reaction temperature and time on the precipitation process and kinetics.

Jan 1, 2003

By Michael Alber

Pullout tests on resin grouted rock bolts have been executed in coal mines and surface test sites. The goal of this study was to provide some qualitative information about the rock mass quality from mandatory tests with a bit little more effort. Movements of rock bolt head and steel plate at different load levels were analyzed and were found to yield information about the rock mass deformability. The tests were interpreted similar to plate bearing tests and a rock mass compressibility index C was assigned. This index reflects the complex interactions between the rock mass, resin grout and bolt under load. Although further research is necessary it may be concluded that those tests may aid in recognizing geological conditions.

Jan 1, 2003

By Charles H. Jacoby

In 1960 the management of International Salt Company made the decision that all waste material from the Watkins Glen plant would be stored in underground salt cavities. The cavities which they contemplated using had been depleted of salt to a point where continued operation would have impaired their structural stability. Originally, the waste to be disposed of included vacuum pan bleeds, cinders, contaminated salt and sewage. It was proposed that this material, in a slurry form, was to be injected into the salt cavity through one of the abandoned wells. Brine, displaced from the cavity, was to be recovered from an adjacent well and subsequently injected into the Cherry Valley limestone, This Cherry Valley limestone which underlies a large portion of north central New York contains a connate water with high concentrations of ammonia, hydrogen sulphide and the chlorides of calcium, magnesium and sodium. A number of questions were immediately raised on various aspects of the technical feasibility of the project. Of major concern was the buildup of insolubles adjacent to the bore of the injection well. Another pertinent question was the carryover in the displaced liquor of finely-divided, mechanically-suspended particles. Criticism was leveled at the inclusion of sewage. Engineering studies were started by the company's Mineral & Mines Development Department and on April 3, 1961 a preliminary feasibility report was issued.

Jan 1, 1973

By Casale G

This paper discusses a long range mine plan development at the Santa Fe Pacific Gold Twin Creeks Mine based on the reserves of Mega pit. The key constraints of the schedule development included two types of mill ore targets (sulphide and oxide mill ore), consideration of blending of six chemical constituents (sulphide sulphur, carbonate, organic carbon, the ratio of iron/[arsenic, antimony]), and mining of acid generating and acid neutralizing waste at pre-defined proportions. Solution approaches, selected results, and project experiences are discussed.

Jan 1, 1995

By Stephen C. Tadolini

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that arc easy to handle/install under temporary or previously supported roof.

Jan 1, 2001

By Etheride MA

The evolution of economic precious metal and copper-gold deposits in high-level igneous terranes is dependent on very efficient fluid focussing. This is most readily achieved by contemporaneous deformation, igneous intrusion and hydrothermal activity. Mineralisation in these environments generally occurs in fault and fault-vein arrays developed in the cover sedimentary and volcanics sequences above older regional scale fault systems. Such reactivated fault systems an particularly prone to developing the complex fracture arrays, extreme local dilation and dramatic increases in permcahilit} that are necessary to efficiently focus hydrothermal fluid and produce large mineral deposits.

Jan 1, 1995

By Yanping Xiao, Ton van Sandwijk, Gus Van Weert, Larry McHugh, Thomas Zabev

"All attempts to remove significant amounts of arsenic from enargite via neutral or reductive pyro routes have required operating temperatures between 600 and 700 º C, too high to propose an equipment development program. Operating at reduced pressures, or using hydrogen or elemental sulphur as a sweeping gas did not help to lower these temperatures. Admixing iron powder gave excellent results, but still required 700 º C. By fortuity, in recent experiments to produce tennantite from an enargite mineral sample, it was observed that enargite was completely converted to bornite, chalcopyrite with minor residual tennantite within an hour at 400-450 ºC. This is believed to be due to the presence of pyrite in the mineral sample treated. All earlier decomposition work appears to have been done on predominantly enargite (i.e. low pyrite) samples, or at high operating temperatures, ignoring possible reactions at lower temperature. The decomposition of enargite into iron substituted tennantite plus some bornite under evolution of liquid elemental sulphur, followed by further decomposition of this tennantite into bornite and volatile arsenic sulphides, appears experimentally feasible at these low temperatures and mimics described ore genesis pathways at > 250 ºC in saline solutions. We suggest two pathways to describe the observed experimental results:20 Cu3AsS4 + 12 FeS2 ???5 Cu10Fe2As4S13 + 2 Cu5FeS4 + 31 S(l)31 S(l) ???31 S(g) (evaporation)5 Cu10Fe2As4S13 ???10 Cu5FeS4 + 10 AsS(g) + 5 As2S3(g)"

Jan 1, 2014

By Waghorn EP, Gleeson HB

The Loy Yang Optr, Cut is a brown coal mine bring developed in the Latrobe Valley region located some 160 kin south-east of Melbourne, Victoria. The mine has been designed to supply a mine mouth power station at a rate that will rise to 32 million tonnes per year by the mid 1990's. Continuous mining metnuds are employed using bucket Whtel excav- ators and conveyors. This paper describes the basis of the design of the Loy Yang continuous mining system ano cne experience of four years of initial operation.

Jan 1, 1987

[ ]

Jan 1, 1989

By Damien Bretall, William Fourney

Due to the changing face of warfare there is an ever growing need to protect the underside of combat vehicles from mine blasts. This paper presents a new method to better characterize the pressure profiles experienced by a plate as the blast develops. The explosive deformation of a small-scale plate was recorded using synchronized high-speed digital cameras, and then analyzed using 3D Digital Image Correlation software. Time-varying pressure profiles were input into an axisymmetric FEM simulation by fitting curves to data obtained from tests using Kolsky bars to measure pressures. These were then modified to find possible profiles that produce the measured deformations. It was discovered that the final deformation cannot be determined from only total impulse or peak pressures, and that it is very sensitive to the time and spatial decay of the pressures.

Jan 1, 2009