Search Documents

By I. J. Burgess, B. C. Barlow

"The electrodissolution of nickel pellets with different controlled electrical variables was investigated in an effort to mitigate plating residue in Watts bath based electroplating cells. During galvanostatic dissolution at 0.4 A dm-2, the anode potential was seen to oscillate between passive and pitting potentials. In-situ microscopy and ex-situ characterization has shown that lacy-pit formation and large, partially perforated, pit covers form during the potential decay from pitting potentials. In general, covered pitting at low current density shows increased plating residue. Using potential pulses is one way to maintain greater control over surface pitting by creating a higher density of pit nuclei while at the same time controlling their growth. Pits generated from a series potential pulses were examined ex situ for a range of pulse times and stages of pit growth were identified. An alternative method of anode dissolution was devised using potential pulses and duty cycles that allowed average current densities comparable to industrial plating conditions to be achieved. By restricting the time at pitting potentials to 0.05 s, plating residue was reduced more than six-fold in comparison to an equivalent galvanostatic experiment run at a comparable current density.INTRODUCTIONIn typical galvanostatic (direct current) nickel electroplating cells employing soluble anodes, some amount of plating residue is produced which consists of metallic nickel and impurities that detach from the bulk in the form of small fines. Significant buildup of residue requires plating operations be halted and the anode assembly cleaned of residue before operation can resume. While variables in the refining process have been shown to affect plating residue, more precise control of electrochemical variables may provide an attractive route to mitigation of residue."

Jan 1, 2016

By Dell H. Adams

COAL EXPLORATION Coal exploration may be defined as the acquisition of data necessary to define and acquire a block of coal which can be mined at a profit. Unlike ore minerals, coal resources are widespread and relatively abundant with supply exceeding demand in almost every case. Thus simple discovery of coal is generally not enough. The chemical and physical variability of individual coal seams, the capital intensive nature of coal mine development, and the changing patterns of utilization require that a multiphase, three-dimensional evaluation be made of each potential reserve. Factors which must be investigated include not only the quantity and quality of the coal but also the geologic, hydrologic, and engineering characteristics of the seam and its surrounding strata. Acquisition of property to provide a secure base for exploration and mine development is equal in importance to the geologic and engineering programs. The successful development of a coal reserve requires that control of coal and, in the case of a strip mine, the surface be in the form of contiguous blocks of sufficient size to support mining. PHASES OF EXPLORATION The high capital risks of coal exploration and land acquisition dictate that a multiphase program be utilized to minimize initial risk. In such a program, phased development of the data insures that each increase in capital expenditures will be justified by a corresponding increase in the level of confidence in the ultimate success of the project. Each phase is designed to provide sufficient data and property control to facilitate the decision whether to proceed to the next phase of development or to discontinue the program (Table 1). The first phase of a typical exploration program consists of a pre-

Jan 1, 1981

By Will Coghill

As the title indicates, this paper treats of the degree of liberation of minerals after grinding. To obtain the supporting data a "tool" not commonly used by metallurgists has been employed. It is the "heavy solution." The advantages gained through its use are shown. Actual ores were employed in order to make the study concrete. The selection was somewhat incidental and happened to embrace the red iron ores of Alabama. So, any reader interested in these ores will find some of their properties described. The red ores constituted the material examined and a somewhat new adaptation of heavy solutions was the tool of examination. If either the ores or the tool interest the reader these notes may be of some value. The writer's chief interest was in the rate of liberation of locked grains. Ores are generally ground preparatory to concentration and as long as the concentrators make suitable products the effectiveness of the grinding is likely to be unquestioned. But when suitable products are difficult to make, an investigation becomes imperative. In such a case a dissection of the ore might be made to find the cause of the trouble. Such a condition of unsuitable products exists in the low-grade red iron ores of Alabama. They are difficult to concentrate. To be sure it might be said that the concentration of iron ores is a new thing and that the ore-dressing methods are undeveloped, but a glance at the industry reveals an abundance of methods and devices for almost all imaginable conditions. Concentrating machinery has not taken a part in this investigation; the use of it would have been only machinery testing, and should never precede the ore testing which consists of such methods as herein outlined. When the properties of the ores have been gleaned the machinery may be used more effectively.

Jan 12, 1926

By Francis S. Kendorski

Rock reinforcement has been in widespread use and generally has been accepted in underground mining and tunneling since the 1950s. The first rock reinforcement technologies employed were mechanical anchors such as split wedges or expansion shells with 5/8-inch-diameter steel bolts. Failures occurred in weak strata which provided poor anchorage or in ground with corrosive waters. Friction rock fixtures consisting of relatively thin-walled tubes have been in use for about 15 to 20 years. While generally performing adequately, longevity problems have developed from corrosion in water bearing ground Longevity of rock reinforcement is much enhanced with grouted bolts. Portland-cement-grouted rock reinforcement has been in use since the mid-1950s, primarily in funneling and other civil engineering underground construction. Tests of decades-old installations have revealed few problems except in ground with aggressive waters. Polyester-resin-grouted rock reinforcement was introduced in the United states to musing in the late 1960s and to tunneling in the early 1970s. Experience from 30 years of resin-grouted bolt installations and field tests have identified longevity problems associated with degradation of steel reinforcing bars, but in generally unusual situations. Improvements continue in resin chemistries, packaging, corrosion protection, grout quantities, and mixing and distribution in the drilled hole to achieve long-term performance. Specific case histories cited with resin- or Portland-cement-grouted rock reinforcement longevity or performance problems, upon close examination, reveal that the causes of the problems were qualify control procedures being inadequate and not in accordance with good practice. Manufacturers' recommendations and engineering specifications, if followed in the field, and with competent inspection and supervision, would have prevented must, if not all, reported longevity or performance difficulties.

Jan 1, 2000

By R. M. Sellwood

The No. 4 I.S.F. Smelter Complex at the Avonmouth Works of Imperial Smelting Corporation (N.S.C.) Limited commenced operation at the beginning of 1968. The furnace rating is 120,000 tons zinc and 40,000 tons lead per annum. Zinc and lead concentrates are unloaded onto a 1,000 tons per hour capacity conveyor belt and automatically weighed and sampled before receipt into a 48,000 ton capacity raw material store. Distribution is by a reversible boom stacker into 16 x 3,000 ton bays and recovery is by a front end loader. Materials are fed to 16 proportioning bins for feeding via continuous weigh feeders to a 132 square metre effective updraught area sinter machine with a material flow rate of 240 tons per hour over the machine. The required quantity of output lump sinter at up to 800ºC is fed to 2 x 600 ton storage bins on the I.S.F. plant. By-product SO2 rich gas is fed to a conventional wet gas single stream acid plant rated at 600 tons per day utilizing a dry N.T.P. gas volume of 100,000 cubic metres per hour. The hot sinter and preheated coke (800ºC) are automatically neighed and charged to a 27.3m2 shaft area I.S.F. fitted with 2 x 5.5 m. wide lead splash condensers. Grade 4 zinc is tapped and transferred to the zinc refinery. Conventional type lead bullion and slag are tapped from the bottom of the furnace through a separation forehearth. The refinery consists of 6 lead and 3 cadmium columns to produce some 52,000 tons per annum of S.H.G. metal. S.H.G. metal and Grade 4 metal is cast into various shapes as required.

Jan 1, 1970

THE problem of reaction rates in the open-hearth process is essentially that of trying to form a fairly clear picture of the "chemical mechanisms" in the bath. Quantitative data on reaction rates would not be very useful even if they were available; however, what few , approximate data there are, can be used in combination with data given in Chapters XVI and XVII to sketch a picture of the "chemical mechanics" of the open-hearth process that is consistent with essentially all the present available evidence. The result may later be found incorrect in many details but even so it will illustrate certain useful methods for obtaining a clearer understanding of the process. As discussed in the last portion of Chapter XIII chemical reactions in general involve the following factors: 1. The reacting molecules are mixed together in space in such fashion as to favor collisions among them. 2. A certain number of collisions occur per unit time among the reagent molecules, depending on their concentration and on temperature. 3. A certain percentage of these collisions result in reaction, these being the collisions between those molecules possessing at the moment energy levels above certain minimum values. The temperature factor enters mainly through (3), and its effect is very marked. (What is called temperature is really the mean energy content of all the molecules of the substance involved; at any one temperature a certain proportion of the molecules will have much higher energy content than the mean value.) Various reaction rates measured at around room temperatures have been found to be speeded from 1.6 to 4.0 times by an increase of only 15 to 20°F., simply because increasing temperature produces a rapidly increasing percentage of molecules with energy levels above the minimum needed to produce chemical reaction in a collision.

Jan 1, 1944

By William M. Bowron

Thirty years ago, when I stood on the cliff of red fossil iron-ore, on Red mountain, Jefferson county, Ala., I asked what were the geological relations of this remarkable deposit. In reply I was told that it was a limestone, colored and saturated by some unknown but wholly external influences, and that at a reasonable distance from the surface the color would disappear. I could find no satisfactory explanation, either of the nature of this wonderful external permeating influence, or of the cause of such a ferrous impregnation selecting this one particular bed of limestone, to the exclusion of the higher and lower beds of the same material which are not even stained. I. The Present Theory. Referring to this subject, Dana says :' "The clays, clayey sandstones and limestones of the Clinton epoch, through New York and the Appalachians, show that the mud-flats and sand-banks, and hence the shallow seas of the coast region, still continued.... The beds of argillaceous iron-ore, which spread so widely through New York and some of the other States, west and south, could not have been formed in an open sea; for clayey iron-deposits do not accumulate under such circumstances. They are proof of extensive marshes, and, therefore, of land near the sea-level. The fragments of crinoids and shells found in these beds are evidence that they were, in part at least, salt-water marshes, and that the tides sometimes reached them." At first, this explanation seemed satisfactory, but the more I studied the ore the less satisfying the explanation became. 1. In the ore itself, I found associated with the small particles of rounded matter (now consisting of iron oxide in which organic structure, if ever present, has become lost, though the

Jan 1, 1906

By Christopher H. Bierbaum

The first significant fact observed in the study of bearing metals is that not a single pure homogeneous metal has given satisfactory service; all bearing metals are alloys made up of two or more phases; that is, they consist of hard and of relatively soft microscopic particles intimately mixed. The function of the hard particles, or bearing crystals, is to support the load and resist the wear when actual metallic contact exists between the bearing surfaces. The functions of the softer particles are to allow the harder particles to adjust themselves to the surface requireinents of the journal and to wear down slightly below the surface of the harder, forming slight depressions on the apparently smooth wearing surface of the bearing, in which some of the lubricant is held when the bearing surfaces are brought into contact with each other. It is this characteristic of certain alloys to form these slight depressions, and thus provide the means for retaining a lubricant, that characterizes them as true bearing metals; in fact, a bearing metal has been defined as "an alloy that is capable of retaining a lubricant upon a bearing surface."' The extent to which the lubricant can be so held determines the most valuable characteristic of an alloy as a bearing metal. An alloy which, perhaps, most characteristically represents a bearing metal is the composition of copper and tin that contains sufficient tin to produce the tin-copper eutectoid, or delta crystal. The depressions worn upon the surfaces of the softer crystals of the teeth of a motor-truck worm wheel, made of an ll-per cent. tin bronze, in many cases were from 5 to 6 microns in depth; all other conditions remaining constant, this depth of wear increases with an increase of working pressure. This copper-tin bronze contains intercrystalline shrinkage cavities, which also

Jan 1, 1923

By Christopher H. Bierbaum

The first significant fact observed in the study of bearing metals is that not a single pure homogeneous metal has given satisfactory service; all bearing metals are alloys made up of two or more phases; that is, they consist of hard and of relatively soft microscopic particles intimately mixed. The function of the hard particles, or bearing crystals, is to support the load and resist the wear when actual metallic contact exists between the bearing surfaces. The functions of the softer particles are to allow the harder particles to adjust themselves to the surface requireinents of the journal and to wear down slightly below the surface of the harder, forming slight depressions on the apparently smooth wearing surface of the bearing, in which some of the lubricant is held when the bearing surfaces are brought into contact with each other. It is this characteristic of certain alloys to form these slight depressions, and thus provide the means for retaining a lubricant, that characterizes them as true bearing metals; in fact, a bearing metal has been defined as "an alloy that is capable of retaining a lubricant upon a bearing surface."' The extent to which the lubricant can be so held determines the most valuable characteristic of an alloy as a bearing metal. An alloy which, perhaps, most characteristically represents a bearing metal is the composition of copper and tin that contains sufficient tin to produce the tin-copper eutectoid, or delta crystal. The depressions worn upon the surfaces of the softer crystals of the teeth of a motor-truck worm wheel, made of an ll-per cent. tin bronze, in many cases were from 5 to 6 microns in depth; all other conditions remaining constant, this depth of wear increases with an increase of working pressure. This copper-tin bronze contains intercrystalline shrinkage cavities, which also

Jan 1, 1923

By W. W. Lowry, G. C. Eggleston, W. E. Keck

THE potential iron ores of Michigan can be classified from the stand- point of the predominant impurities into siliceous, sulphurous and phosphorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral-specular hematite and massive hematite. The latter is the principal variety, but the former is an important mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (1) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1937

By Gabriel Voicu, Marc Bardoux, Ross Stevenson, Nuno Machado, Jean Lafrance

"Abstract - Paleoproterozoic gold is found in two different volcano-sedimentary sequences and intrusive bodies separated by 600 km within the Guiana Shield. The 2148 Ma St-Élie granite intruded volcanic-arc sequences of the Paramaca Group, whereas the 2096 Ma Omai stock penetrated backarc/ island-arc sequences of the Barama-Mazaruni Group. Positive ?Nd values suggest that both suites lack Archean crustal contaminants, which is consistent with an origin in an oceanic arc setting.The St-Élie deposit is characterized by quartz-dominant vein systems with minor metallic minerals, represented chiefly by pyrrhotite and pyrite. Biotite, calcite, and chlorite are the main gangue minerals. The alteration haloes at St-Élie feature a strong potassic zone, which is absent at Omai. The ore-controlling structures are ductile and the vein emplacement is related mainly to contemporaneous, high-angle ductile shear zones. The St-Élie deposit formed at temperatures >350°C. The stable isotopes values are compatible with a magmatic or metamorphic source.The Omai deposit is characterized by quartz-dominant vein systems with minor metallic minerals, represented mainly by pyrite. Ankerite, scheelite, albite, and chlorite are common gangue minerals. The vein emplacement is syn- to post-deformation and it is related mainly to brittle shear zones with low-angle, stockwork networks and breccia zones. The Omai deposit formed in a temperature range between 250°C and 170°C, much lower than the St-Élie deposit. The stable isotope values are compatible with mixing between deep-seated fluids of metamorphic or magmatic origin with surface- derived fluids.These differences between St-Élie and Omai are interpreted in terms of their depth of formation. Alteration patterns, structural elements, and paragenetic assemblages indicate that the gold at St-Élie was most probably emplaced at a mesozonal depth, whereas the Omai setting yields evidence for epizonal conditions."

Jan 1, 1999

By John L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former U.S. Bureau of Mines to develop techniques that will reduce the hazards in the mining work place associated with coal bumps. Current research focuses on both analyzing historical seismic data from bump-prone operations and utilizing a mine-wide seismic network to investigate the exact strata failure mechanics associated with bump-prone geology. The anticipated outcome of this research will be reduced bump incidences through advanced engineering concepts and designs which implement the new understanding of strata behavior. The analysis of the historic seismic data consists of correlating observed mining seismicity with the geologic and geometric parameters at the sites. The primary seismic parameters are the timing, location and magnitude of a recorded seismic event. These parameters are correlated with such mining parameters as: the overburden, the size of the immediate gob, the size of the district gob area, etc. This detailed analysis of historical seismic data has provided an informative quantifiable relationship between many of the specific mining parameters and the induced seismicity. The second aspect of the coal bump research is the instrumentation of an appropriate field site to determine the main roof, floor, and gob behavior associated with hump behavior. The chosen field site is a deep-cover longwall mine with competent geology in a historically bump-prone area. The primary field instrumentation is a three-dimensional, full-waveform, seismic array with both surface and underground sensors surrounding an active multi-panel district. The purpose of this seismic array is to determine the timing, the exact location, and the mechanism (tensile fracture, bedding plane slip. etc.) of the failure of the strata surrounding the active and multi¬panel gobs. The preliminary results presented in this paper help to define the strata failure areas around the longwall panel.

Jan 1, 2000

By Rodnei Graça, Jorge Silva Bettencourt, Lena Virgínia Soares Monteiro, Baruch Spiro, Tolentino Flávio De Oliveira

Abstract - The Vazante Mine is located in the Vazante District, the largest zinc district in Brazil. The Vazante deposit consists dominantly of an unusual willemitic ore. Small sulfide bodies are tectonically imbricated with the willemitic ore, within the Vazante shear zone. Structural styles of deformation and petrographic and isotopic evidence indicate that willemitic mineralization and deformation occurred synchronously during the Neo-Proterozoic. Various generations of hydrothermal veins and hydraulic breccias may pre-date, accompany and overprint the mineralization. Ore-formation temperatures are deduced from stable isotope geothermometry and mineral chemistry of both sulfide bodies and willemitic ore. Temperatures during the main stage of mineralization range from 206°C to 294°C (willemitic ore) and 317°C (sulfides), and reflect the prevailing metamorphic conditions within the shear zone. The fluid from which the gangue minerals of the sulfide bodies precipitated (at 250°C) had an oxygen isotopic average value of ?18O = +19.4‰. This value appears to reflect the interaction of metamorphic fluid with the carbonate rocks of the Vazante formation. At 250°C, the fluid in equilibrium with the vein mineral phases and willemitic ore assemblage exhibits a uniform oxygen isotopic composition, with an average value of ?18O = +11.5‰. The positive linear covariance of ?18O and ?13C ratios of the carbonates is most likely due to the mixing of metamorphic and meteoric fluids. The ?34S values of sulfides indicate a direct crustal origin for the sulfur. It is suggested that the sulfur is largely derived from pre-existing sulfide bodies and has been transported by metamorphic fluids. The willemitic ore may have originated from the precipitation of metal in sulfur- poor fluids under oxidized conditions, within the Vazante shear zone.

Jan 1, 1999

By L. Lamothe, C. H. The

"Pilot precipitator tests were conducted at Noranda's Horne Smelter in late 1978 to evaluate methods of improving converter dust collection efficiency. A bout 35 Nms/min. of converter off-gas were isokineticatly diverted from the converter flue to the pilot precipitator leased from Flakt (Canada) Ltd., consisting of three fields, one transformer-rectifier set per field and 77-m2 total collecting plate area. The effects of gas volume flow rate and conditioning the gas with sulphur trioxide and/or additional moisture were tested. II was found that gas flow rate and moisture level had the most pronounced effect on collection efficiency. Based on a techno-economic assessment of different options for improving converter Courell efficiency, waffle hoods and water sprays were installed on the converters to reduce air infiltration and increase the moisture level in the gas.BackgroundThe Horne Smelter of Noranda Inc. is situated in northwestern Quebec and, since the closure o f the min e in 1976, has been operating as a custom smelter. The concentrates treated at the smelter come from various mines with mixed sulphide ores , many o f them containing significant amounts of lead and zinc which makes dust collection in electrostatic precipitators mo re difficult than normal.As part of a continuing program on reducing smelter dust emissions, the No . 6 Cottrell was installed in 1972 up stream of Nos. 2 and 4 Cottrells (in parallel) in a n attempt to improve dust collection by increasing the over- all precipitator capacity ( Fig. I). However, it has never per formed a t its designed efficiency o f 94%. The average efficiency established in various test s was in the range of 60 – 65%."

Jan 1, 1985

By Pinczewski WV, Nowak LP, Tanzil WBU, Jenkins DR, McCarthy MJ

An experimental and theoretical study has been made of the drainage behaviour of two-dimensional packed beds drained from an outlet in the sidewall of the bed in order to identify the fundamental me- chanisms involved. Under these conditions a grad- ient develops in the air-liquid interface in the direction of flow with the interface tilting towards the outlet. This results in a significant volume of liquid being retained in the packing on completion of draining when the interface first reaches the bed outlet. Residual liquid volume and the shape of the air-liquid interface as a function of time were det- ermined experimentally in a two-dimensional packed bed where the packing consisted of glass spheres ranging in size from 0.6 to 10 mm dia. and the bed was drained at superficial liquid velocities rang- ing from 0.007 to 0.32cm/s. The test liquids used were water, glycerine/water solutions and kerosene resulting in a viscosity range of 1 to 10 mPa.s and a surface tension range of 0.0243 to 0.072 N/m. Assuming laminar flow within the bed, a compu- tational model was developed to predict both the liquid residual ratio and the temporal evolution of the drainage profile within the bed. The computed results were in good agreement with the experimental data over the entire range of conditions invest- igated. the computational model was used to estimate the relative importance of the effects of changes in hearth conditions on residual slag volume for typ- ical blast furnace operating conditions. On the basis of the computed results it is concluded that coke quality is a major parameter affecting hearth drainage performance.

Jan 1, 1981

By Terry J. Close

The Gates of the Mountains Wilderness study area is underlain by intrusive and sedimentary rocks, mainly limestone. No limestone has been produced from the study area; suitable material is more readily available elsewhere. Small amounts of gold, sapphires, and corundum were produced from a placer deposit along the banks of the Missouri River. The remaining gravel contains low mineral values. Other alluvial deposits along the Missouri River and Beaver Creek contain no identified economic resources other than sand and gravel. Some deposits could provide suitable construction material for local use.

Jan 1, 1984

By T. A. Rickard

The interior of West Australia is an arid table-land, elevated 1400 feet above the sea. This plateau is flanked to the south by the Tertiary limestones which fringe the Great Australian Bight. It is bordered northward by the Carboniferous beds of the Fitzroy river and westward by the granite of the Darling hills, while to the cast this wide area, about 900 miles square, slopes downward imperceptibly into an undulating plain of sand, which stretches with dismal persistence across the boundary of South Australia. The waters of the ocean receded from this tract of land long ago; it is probably the oldest landsurface on the globe, and represents the basal wreck of a much larger continent. Fig. 1 is a map of this region. The Coolgardie and Kalgoorlie gold-fields are situated in the southwestern part of the region. The rock-formation consists of granite penetrated by diorites and andesites. The latter are occasionally associated with tuff's, which have been readily mistaken for sedimentaries. There are no fossil-bearing rocks, such as would afford a datum-line from which to measure the relative geological age of the prevailing formation. On the extreme edges of the mining territory there are, it is true, remnants of sand-rock which are considered identical with the " Desert Sandstone " of Queensland, determined by Daintree to be of Mesozoic age. But even this formation has evidently been laid down so long subsequent to the underlying rocks that it serves merely to emphasize their much greater antiquity. In their characteristics and in their relations to each other, the granite and the diorite of the Coolgardie region appear to me much to resemble the Laurentian granite and the Huronian

Jan 1, 1899

By G. J. Kipouros, P. W. Kingston, W. F. Caley

"Current practice in advanced materials processing has involved the dispersion of a second-phase, commonly SiC, glass, or other non-metallic fibres/whiskers/particulates to enhance physical characteristics of the matrix. These matrices may be either ceramic or metallic but in either case it is important that the physical and chemical properties of each phase be compatible. The dispersed, finely divided second phase is often both expensive and foreign-produced and may exhibit chemical instability at elevated temperatures. Thus, it would appear that certain naturally-occurring industrial mineral fibres/whiskers/particulates might offer an attractive and low-cost alternative. Suitable candidates, such as wollastonite and sillimanite, are available in Canada and may be milled to produce particles whose shape is appropriate for this application. It is suggested that wollastonite, in particular, may be a useful modifying agent in metal matrix composites utilizing AI, Al-Si, Zn-Al or other light metals and alloys. In addition, the possible use of these minerals in ceramic matrix materials is also addressed, with reference to a preliminary thermodynamic analysis of the systems involved.IntroductionBackgroundA composite material may be thought of as consisting of a matrix component, the properties of which are improved by the addition of a second component or dispersed phase which forms a distinct three-dimensional interface with the matrix. This matrix is commonly either metallic or ceramic, which leads to the two most popular types of composites: metal-matrix composites (MMC); and ceramic-matrix composites (CMC).Such materials are by no means new. Early composites include fiberglass, mixtures of plaster and horsehair in wall plastering, as well as use of natural materials such as bamboo in fishing rods. Some of the newer applications include high strength, low-weight bicycle rims, as well as the more familiar role in aircraft and automobile engine components."

Jan 1, 1993

By T. Lee

The mining industry, both here and internationally, is continually developing increasingly sophisticated software to compute mineral resource estimates, but these processes cannot compensate for a flawed geological interpretation of the geology of the economic commodity(s) concentrations. Quality assurance and quality control (QA/QC) is becoming increasingly common in association with the sampling and assaying practices within the industry. However, it is rare in the case of a geological interpretation associated with mineral resource estimation. Why? In the context of this paper, QA/QC relates to the use of statistical and graphical tools to show that the geological economic commodity concentrations have been appropriately domained. Domaining is essential to improve the chance of getting a mineral resource estimate right. Commodity value and acceptable concentration variation within a mineral resource can be ingredients that make mineral resource estimation difficult to get right. But it is possible to get it right a very high proportion of the time. It is more likely to occur when inappropriate data consolidation is minimised. In any case, inappropriate data consolidation is significantly reduced when the geological interpretation is strongly consistent with the data and it is demonstrable. To achieve quality global estimates of geological domain concentrations, it is essential that the geology of the prospect is understood sufficiently that the deposit is appropriately domained. Appropriate domaining occurs when sample populations are separated in such a way that only data in harmony with each other within the population contributes to the domain's concentration estimate. The paper will use four brief case studies to illustrate how QA/QC can be used to display data and validate the underpinning geological interpretation through its associated domaining to get it right when it comes to a mineral resource estimation.

Jan 1, 2007

By M. E. Ramírez

In this research bioleaching or extraction of iron present in a kaolin from La Virgen mine, Anti-oquia/Colombia, was carried out. Organic acids produced in SF with Aspergillus niger were used in the process. The fermentation process was carried out in 3 L aerobic stirred bioreactors, at a temperature of 30 °C, a stirrerd speed of 700 rpm, an initial pH of 4 and a fermentation time variable between one to 8 days, obtaining broth fermentation samples daily per bioreactor. For iron extraction, fermented broth from second to sixth day of fermentation was evaluated and it was found that the fermentation broth of the third day showed a larger potential for iron removal, 786 ppm, by using kaolin with an initial iron content of 1401 ppm. A set of tests using commercial organics acids such as citric acid and oxalic were carried out because those were found in the fermentation broth and it was found that oxalic acid presented three times more iron removal than citric acid.

Jan 1, 2014