Search Documents

By E. R. Bollinger, N. S. Tanious, R. D. Beckett

The US Bureau of Mines developed hand-made, steel-fiber-reinforced concrete (SFC) blocks for building mine cribs. To ensure wider usage of these cribs, US Steel Mining Co. initiated a joint development and evaluation program with Burrell Construction Co. to mass produce SFC blocks of reasonable dimension, weight, and cost. Small specimens and full-size cribs were evaluated to determine their compressive strength and post failure characteristics. After testing and adjusting of various concrete mixtures, a final formulation was selected that gave a nominal crib strength of 22 MPa (3200 psi) and a nominal modulus of elasticity of 6.9 GPa (1.0 x 106 psi.) These SFC cribs can support 6.4 times as much as a wood crib with the same load-bearing area. The SFC crib was proven to be an economical and effective roof support system through various underground installations.

Jan 1, 1987

By D. J. Parker

Since the introduction of electricity into the mines of the United States , the hazards incident to the industry have increased materially in both coal and metal mines . For economic reasons the tendency at present , particularly in coal mining , is decidedly toward the adoption of electrical mine machinery , including alternating current machinery , on a more extensive scale than ever before . Obviously, the growing use of such equipment will result in an ever -increasing number of underground transformer stations . The principal electrical hazards in mines are threefold ; fire , explosion, and contact . Of these , fire is the greatest hazard involved in the use of electricity underground , and several fires have originated in underground transformer and motor generator set stations . The fire hazard due to improperly installed and poorly maintained underground transformer stations is an ever-present one , and failure to take the necessariman remedial action is likely to result , sooner or later, in the destruction of life and property . Upon suggesting the necessary corrective measures with respect to such installations , one is often confronted with the statement to the effect that even though this particular hazard has existed over a period of years , there have been no unfavorable results therefrom thus far . Frequently , the desirability for action is not apparent to the mine management until it is too late . Because a mine has a record free from fires , explosions , etc. , over a number of years of operation during which these hazards existed , such good fortune should not be taken as a guarantee that this or any other mine is immune from these common dangers . When the elements of an existing hazard are properly balanced or in the right proportion, the unfortunate combination must of necessity culminate in misfortune of one kind or another. The fire hazard due to underground transformer installations can be very definitely minimized by proper installation and maintenance . In coal mines the transformer banks , connected to 2,300 and occasionally to 4,400 volt circuits , are often found located in open- ended crosscuts , mounted on concrete or timber foundations , and in nonfireproof surroundings .

Jul 1, 1930

By Carl L. Morris

This short dissertation concerning "what the client expects from the engineer" is directed mainly at the design and construction of metallic ore concentration or beneficiation plants. However, practically the same conditions apply to the design and construction of cement and lime manufacturing facilities, with the exception that the latter facilities reflect the client's and engineer's concepts of customer service and in some cases reflect promotional considerations for the product manufactured and distributed. The client expects his engineering contractor to contribute in an efficient, cooperative, and economical manner current industry-wide know-how and experience to the specific project under consideration through the client's organization

Jan 1, 1969

By M. O?Driscoll

The tide has turned. Developments in China that have continued to unfold over the last four years or so have now reached a point where the supply market dynamics of certain industrial minerals have changed significantly. No more is this sea change better exemplified than by the supply market for magnesite, and in particular, its processed derivative grades of dead burned magnesia (DBM), caustic calcined magnesia (CCM), and fused magnesia (FM). But what has compounded the barrage of influencing factors impacting this sector, which include the widespread effects of energy and freight cost increases, has been rising demand from certain end use markets. Clearly, the magnesia market is experiencing bittersweet conditions. But those western producers which have monitored and responded to this market transformation, stand to taste success in the near and medium future. REVOLUTION IN WORLD SUPPLY STATUS In essence, while China, as host to a wealth of magnesite resources in Liaoning province, remains a huge producer of magnesia, its supply dominance on the global magnesia market has been considerably weakened. In future, it will mainly aim to supply domestic, and to some extent east Asian markets. Magnesia consumers outside China are now scrabbling for alternative, ?western? sources of supply. At the same time, magnesia producers outside China that weathered the storm of low cost Chinese DBM and FM imports flooding their regional markets for the last 20 years (and many did not), are busy investing in production capacity increases to meet not just demand from falling Chinese supply, but also demand from end use markets which is picking up. And it is not just a matter of expanding capacity of existing magnesia product lines. In the face of plentiful lower cost DBM and FM substitutes from China over the last couple of decades, many western magnesia producers started to switch their focus to the non-refractory markets (eg. environmental, specialities) which promised lucrative opportunities (and still do) and crucially, a lessening of sales revenue dependence on the DBM refractories market. Now we have the likes of Baymag (Canada), Bommag (Serbia/Turkey), and Kumas (Turkey) not only expanding capacities but seriously considering diversifying into DBM and FM production. Perhaps DSP (Israel), having ceased its famous high purity DBM activity as recently as 2005, might even reconsider a return to the ?other side?. But it?s not all DBM and FM. The CCM and specialities markets are also demanding a response, and so Baymag, DSP, Martin Marietta (USA), Premier Chemicals (USA), Qmag (Australia), MGR (Spain), and Magnifin (Austria) are also stepping up to the market on the non-refractory side. From most accounts, the situation with regard to Chinese supply has been described as one of turmoil, with prices rising, leading to improving opportunities for western producers. The majors are conducting huge expansion programmes, such as Qmag, Magnezit (Russia), and the new look Magnesita (Brazil). Even smaller players such as Causmag (Australia) and Dalmia (India) are looking to increase production. In short, the western magnesia supply sector is witnessing a landmark event in capacity investment and market share penetration as China?s previously dominant role begins to weaken (for a review of western capacity expansions see Industrial Minerals, September 2008, p.28). MERGER & ACQUISITION ACTIVITY Another response of course has been a raft of mergers and acquisitions in order to secure resources and supply outside China. These have included private equity groups taking over Magnesita and Qmag; Imerys entering the FM business through UCM; Peñoles further consolidating the electrical grade FM market by acquiring Minco; Martin Marietta acquiring Morton Salt?s Specialty Magnesia Group; Bomex entering the market through Calmag (now Bommag); LWB acquiring Magnesita; and Magnezit?s pursuit of Slovakian magnesia, with Slovmag aboard while currently wooing SMZ. Interestingly, RHI has gone ?the other way?, and has invested in a state of the art joint venture operation at Dashiqiao, Liaoning, with which it aims to secure high quality feedstock for its Chinese refractory plants. Tata Refractories Ltd has announced intentions to follow suit, and other majors, such as Qmag are known to be interested in seeking options. Naturally, there is now renewed interest from several parties in the idled 50,000 tpa DBM/10,000 CCM Jormag facility, Jordan, and the commercially undeveloped Zhargat project, Saudi Arabia. Elsewhere, there will no doubt be suitors for stakes in SMZ, in Slovakia, and Magnohrom, in Serbia, whose respective ownerships are on the block. THE ?CHINA FACTOR? The ?China factor? has been key to magnesia?s market change, and has significantly influenced prices and availability of material to global markets. Resources & production China hosts the largest share of the world?s magnesite deposits, accounting for 26% or 3,319m. tonnes of predominantly sparry magnesite (followed by North Korea, 24%, and Russia, 22%; Wilson 2008). China accounts for 44% of total world magnesite mined (19m. tonnes in 2007) and 50% of the total world magnesia produced (8.2m. tonnes CCM, DBM, FM; Wilson 2008). Russia follows China at 13% of magnesia supply, illustrating China?s dominance of magnesia production. Apart from one producer in Shandong province, central eastern China, the country?s magnesite resources and production are concentrated around the cities of Haicheng and Dashiqiao in Liaoning province, north-east China. Although there are also producers in the Xiuyan district of south-east Liaoning, the Haicheng-Dashiqiao Magnesite Belt hosts the majority of producers. In total these may number 200-300 of large,

Jan 1, 2009

By Pekka Taskine

In the Kokkola zinc smelter, as in most other zinc roasting plants, there is now a trend towards using concentrates with an increasing impurity content. This also often means that the size distribution of the concentrates gets finer. Iron is present in sulfidic zinc concentrates with the highest percentage as a single impurity. The behavior of iron in zinc roasting was studied in laboratory experiments. Commercial zinc concentrates with a low and high (1.5 - 16 wt-%) iron content as pyrite or in the sphalerite lattice were oxidized to various degrees to establish the reaction mechanisms of iron in roasting. Microscopy studies were carried out on the calcine, and the findings were presented in numerous photographs of the polished cross sections. SEM/EDS techniques were used for analyzing the phases and particle morphologies present in the samples. An oxidation mechanism of zinc concentrates with a high iron content was suggested.

Jan 1, 2002

By Ralph W. Smith

Development of the lime industry in Ste. Genevieve County began in a crude way in 1840. According to information furnished by the Missouri Bureau of Geology, in the early days small vertical kilns built of stone were used, and wood was the fuel. Modern development began in 1904 when one company introduced steel shells lined with firebrick. Within a few years two more companies erected similar plants, and in 1925 a fourth company began operations. Thus there arc today four lime companies at Ste. Genevieve, all operating at high capacity and with a gradually increasing production. Geology The limestone of Ste. Genevieve County, which has the chemical composition and purity required for lime burning, is the upper 80 or 90 ft, of Spergen formation. The Missouri Bureau of Geology, in its geological map of Ste. Genevieve County, gives the Spergen formation a total thickness of 160 ft., but only the upper portion is pure enough for lime burning, with an average raw-stone analysis of 98.7 per cent CaCo3; 0.35 SiO2; 0.3 R2O3; 0.35 MgCO3; 0.3 SO3. The Spergen, one member of the Meramac group, Iowa series, of the Mississippian system, underlies an area approximately 12 miles long north and south, by 5 miles wide east and west (Fig. 1) in Ste. Genevieve County. The entire eastern two-thirds of Ste. Genevieve County is sedimentary, the formations dipping gently toward the east on an average grade of about 4 per cent, or 2 1/2°. Thus the outcrops of the various sedimentaries run approximately north and south. A line running west from Ste. Genevievc crosses the outcrops of the sedimentaries, ranging from the top of the Mississippian to the Ozarkian geological system in a space of 12 miles. Thus with the gentle dip of 2 1/2° the 160-ft. thickness of the Spergen formation stretches out in its outcrop so that it is approximately one mile wide. The early quarry and lime developments at Ste. Genevieve mere in this easily obtained surface rock of the Spergen outcrop.

Jan 1, 1938

By Ralph W. Smith

Development of the lime industry in Ste. Genevieve County began in a crude way in 1840. According to information furnished by the Missouri Bureau of Geology, in the early days small vertical kilns built of stone were used, and wood was the fuel. Modern development began in 1904 when one company introduced steel shells lined with firebrick. Within a few years two more companies erected similar plants, and in 1925 a fourth company began operations. Thus there arc today four lime companies at Ste. Genevieve, all operating at high capacity and with a gradually increasing production. Geology The limestone of Ste. Genevieve County, which has the chemical composition and purity required for lime burning, is the upper 80 or 90 ft, of Spergen formation. The Missouri Bureau of Geology, in its geological map of Ste. Genevieve County, gives the Spergen formation a total thickness of 160 ft., but only the upper portion is pure enough for lime burning, with an average raw-stone analysis of 98.7 per cent CaCo3; 0.35 SiO2; 0.3 R2O3; 0.35 MgCO3; 0.3 SO3. The Spergen, one member of the Meramac group, Iowa series, of the Mississippian system, underlies an area approximately 12 miles long north and south, by 5 miles wide east and west (Fig. 1) in Ste. Genevieve County. The entire eastern two-thirds of Ste. Genevieve County is sedimentary, the formations dipping gently toward the east on an average grade of about 4 per cent, or 2 1/2°. Thus the outcrops of the various sedimentaries run approximately north and south. A line running west from Ste. Genevievc crosses the outcrops of the sedimentaries, ranging from the top of the Mississippian to the Ozarkian geological system in a space of 12 miles. Thus with the gentle dip of 2 1/2° the 160-ft. thickness of the Spergen formation stretches out in its outcrop so that it is approximately one mile wide. The early quarry and lime developments at Ste. Genevieve mere in this easily obtained surface rock of the Spergen outcrop.

Jan 1, 1938

By Reul A. Dejú

The mineral olivine has been the subject of continued research by various authors. Paik (1967) conducted infrared and flotation studies of the adsorption of sodium alkyl benzene sulfonates on olivine. These studies are of interest from two points of view. First, in the metallurgical field it is of interest to understand the mechanism of silicate flotation using sulfonate collectors and second to a hydrologist studying the pollution of surface or subsurface waters it is of interest to study the reactions taking place when water plus sulfonates encounter a porous (silicate) medium. On the basis of Paik's study he was able to postulate a possible mechanism for the attachment of RSO3 (sulfonate radical) to the olivine surface. Parks (1969) has been studying the important influence of the structure of a silicate such as olivine on its dissolution mechanism and its related surface charge. Also Luce, a student of Parks (1964, 1965) has been studying the kinetics of dissolution of olivine using the techniques of direct solution analysis and infrared analysis. Certainly a classic in the study of silicate dissolution is the work of Murata (1940) on the reaction of orthosilicates (olivine in particular) with strong acid solutions. Many authors (Dejú and Bhappu, 1966. 1967. 1968, Dejú, 1969; Rhoades and Krueger. 1968, and Faust and blunter, 1967) have reported studies of the behavior of silicates immersed in water (especially orthosilicates) and have found that there is an exchange of cations from the silicate surface for H+ from the water. Studies by Dejú and Bhappu have also included the system olivine-water-amine.

Jan 1, 1971

By V Mutton, L Potts, D Joyce

This paper describes the method of extracting sill pillars within the underground operation from under unconsolidated mullock fill at the Cracow Gold Mine. This pillar recovery method was initially successfully used to recover sill pillars at Crusader Mine, Western Australia in 2001. Globally significant resources have been sterilised due to the placement of loose rock fill above crown pillars and within adjacent stopes. The method described here offers significant opportunities to increase recovery of sill pillar recoveries.The royal orebody sill pillars at Cracow Gold Mine form a significant resource. Extraction of these pillars needed to be undertaken with minimal ore dilution and maximum ore recovery. The application that was selected to consolidate the loose mullock fill above each pillar used an injection grouting process (Minova FB200).Cracow Gold Mine mining method is bottom up bench mining. The pillars were left within the orebody to allow for stoping to commence whilst the decline was being developed. Due to the remainder of the orebody being extracted the only access to consolidate the backfill was from the sill pillar extraction level. Numerous problems were encountered and overcome from product selection and trial, system of injection to extraction.This pillar recovery process achieved a 95 per cent recovery of the sill pillar compared with an estimated 60 per cent typical for other mining options.CITATION:Potts, L, Mutton, V and Joyce, D, 2012. Pillar recovery at Cracow gold mine using grouted consolidated mullock, in Proceedings Narrow Vein Mining 2012 , pp 179-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By A. CHESTER BEATTY

SO much has been written about African, and particularly about Northern Rhodesian, copper during the past two years that I feel safe in assuming that you are familiar with the general background of the Rhodesian picture. Therefore, I will confine myself to certain of the high lights in connection with the history, geology, development, ore reserves, and contemplated mining methods in this relatively new and highly important copper field., Unlike most of the other great orebodies of the world, the Roan Antelope mine was not discovered by the hoof of a starving prospector's faithful burro; nor even, as its name might suggest, by a well-placed kick of protest from an antelope stumbling over a malachite outcrop. Late in 1905 an English prospector named Collier, traveling in the N'Dola district, came upon some natives using a green powder for medicinal purposes. Closer examination of the powder revealed that it ' was ground-up malachite. Collier endeavored to persuade the natives to tell him where they obtained this medicine, but' for a long time without success, because of the general feeling among the natives that they did not wish to reveal the resources of their land to the white. Finally however, - he persuaded- brie 'of-the elders to at" least take 'him part way toward, the- place where the malachite was supposed to occur. The bid took him, to a point on the lower regions of the Luanshya river and there left him with the instructions that if he followed the stream up toward its.

Jan 1, 1931

By R. E. Kennedy

The presence of combustible gases and vapors in air can constitute n extremely serious explosion hazard. This hazard is even greater when explosive mixtures are confined under high pressures, as the pressure can become tremendous immediately before the container is ruptured. Because of its interest in safety in mining and. allied industries, the U. S. Bureau of Mines has investigated the explosive properties of a number of gaseous and liquid compounds; the results of these investigations have been published in various government papers and journal articles. The increased use of liquefied, petroleum gases has intensified interest in the effect of high pressures on the explosibility of propane-air mixtures. The limits of flammability of natural gas-air mixtures have been determined at pressures ranging from 50 min. Hg to 3,000 p.s.i. As it is known that a combustible. gas or vapor cannot burn or explode when the oxygen content of the atmosphere is less than a certain value, critical values were determined for the oxygen content of atmospheres to which nitrogen had been added as a diluent. In this connection limits of flammability were determined for ethane in atmospheres containing added. nitrogen or carbon dioxide at pressures up to 900 p.s.i.g.

Jan 1, 1951

In spite of advances in measurement techniques and an explosive increase in the volume of research, our understanding of human strength remains in its introductory stages. It is clear that muscle strength is a highly complex and variable function that depends on a large number of factors. It is not surprising, therefore, that large differences in strength exist not only between individuals, but even within the same individual tested repeatedly on a given piece of equipment. The issue is compounded by the fact that correlations of strength among different muscle groups in the same individual are generally low, and tests of isometric strength do not necessarily reflect the strength an individual might exhibit in a dynamic test. As a result of these and other influences, great care needs to be exercised in designing, evaluating, reporting, and interpreting muscular strength assessments. Traditionally, tests of muscular strength were in the domain of the orthopaedist, physical therapist, and exercise physiologist. Such tests are also an important tool for the ergonomist, however, because of the high strength demands on workers in manual materials-handling tasks. In some cases, task demands may approach or even exceed the strength that an individual is voluntarily willing to exert in a test of strength. In such cases, evidence suggests that the likelihood of injury is significantly greater than when the task demands lie well within an individual's strength capacity. Because the relationship among strength capabilities, job demands, and musculoskeletal injury has been established, it is apparent that tests of muscular strength may benefit the ergonomist both in designing jobs and in ensuring that individuals have sufficient strength to safely perform physically demanding jobs. Several strength assessment techniques have been employed for these purposes, each possessing unique characteristics and applicability to job design and worker selection procedures. Our main purpose has been to elucidate these strengths and weaknesses, so that tests of strength may be properly applied in designing jobs and selecting workers. One of the crucial points we have emphasized is that any test of strength used in job design or worker selection must be directly related to the demands of the job.(1) For example, if an occupational lifting task has a high dynamic component, a test of isometric strength is not likely to provide the data necessary for proper design of the job. Of course, dynamic strength tests would also be misapplied in assessing a job requiring isometric exertions. Another potential pitfall is using tests of strength on isolated muscle groups and assuming that they are indicative of whole-body strength. For example, one might mistakenly assume that dynamic trunk extension strength represents a person's capability to perform a lifting task. However, an individual's lifting capacity may be entirely unrelated to trunk extension strength. It may, instead, be limited by an individual's arm or leg strength, depending on the task being performed. A final point on strength assessment should be made. An individual's strength capability cannot be considered a fixed human attribute. Strength training regimens can increase an individual's strength capability by 30%-40%. Whether

Jan 1, 1998

By S. C. Sun, A. M. Gaudin

This paper presents the results of a. study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresisl-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation _ 4µ(300)² Z= kx in which z is the zeta potential expressed in in volts, µ the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas. The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mixture of water, copper sulphate and xan-thate, we can calculate the zeta coefficient

Jan 1, 1947

By H. R. Deeth, C. J. Koenig

About ten years ago nepheline syenite was introduced to the ceramic industry and the material has now found application in the various branches of the industry, namely, as a vitrifying agent in white-wares and as a source of alumina and alkalies in glasses, glazes, and porcelain enamels. Spencel described the early mining and processing developments regarding this material. Since the time of his article many research papers have appeared relating to the usage of nepheline syenite but little has been published relative to subsequent mining and processing methods. A complete indexed review of the literature was issued recently by Ohio State University.2 Since "Lakefield" nepheline syenite from Blue Mountain, Ontario (Fig I); is the only commercial ceramic-grade nepheline syenite now being marketed on this continent, discussion is limited to this operation carried on by American Nepheline Limited, Lakefield, Ont., and its subsidiary in the United States, American Nepheline Cory. at Rochester, N. Y. The Deposit Blue Mountain is a long ridge rising to an elevation of about 350 ft at its highest point above the surrounding country and extending for about six miles in a northeasterly direction across Methuen township, Peterborough County. The rock of the Blue Mountain central alkaline intrusive is fine grained, light colored and of even granitic texture. The solidified mass consists predominately of the minerals albite, nepheline and microcline in order of abundance. The average mineralogical composition for the deposit obtained by a study of 112 samples taken regularly over the whole formation is as follows:3 Volumetric Mineral Per Cent Albite.................... 54 Microcline................ 20 Nepheline................ 22 Muscovite................ 2 Mafics.................... 2 (Biotite, hastingsite, magnetite) Total................... loo The mineral nepheline (or nephelite) belongs to the feldspathoid group but is lower in silica content than are the feldspars. It is a silicate of soda, potash, and alumina (NaKAl2O32SiO2). Its presence with albite (Na2oA12O3 6SiO2) and microcline (K2O A12O3 6SiO2) gives the Blue Mountain deposit an alkali content of 15 pct and an alumina content of approximately 24 pct. While this huge alkaline mass is somewhat variable mineralogically, it has a uniform chemical composition. When the iron, mostly in the form of magnetite, is removed during processing, a remarkably uniform finished product is obtained. Geological surveying has disclosed many million tons of nepheline syenite in the Blue Mountain deposit. Diamond drilling in the area where mining is now being carried out indicates a block of about one million tons.

Jan 1, 1949

By A. M. Gaudin, S. C. Sun

This paper presents the results of a. study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresisl-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation _ 4µ(300)² Z= kx in which z is the zeta potential expressed in in volts, µ the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas. The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mixture of water, copper sulphate and xan-thate, we can calculate the zeta coefficient

Jan 1, 1947

By Steve Stuart

Deep-sea mineral SMS deposits present some of the world’s most challenging conditions for drilling equipment. As robotic seabed drilling services mature so too the ways that clients engage with service providers to maximise their data requirements. This presentation reviews key considerations for planning and executing a successful seabeddrilling program in variable mineralised deposits. Some of the means of collaboration between robotic seabed drilling contractors and those hiring their services are explored; where improved efficiencies and recoveries over the period of a drilling programme could be achieved. Potentially new technology or methodology can be looked at to further improve these approaches.

Sep 1, 2014

By Charles Reed

WITH the increasing importance of clay in drilling operations which demand more precise and exacting control over its behavior, there has come the realization that most of our present methods of control over many of its important properties still represent more of an art than a science. Such a situation with respect to a material of such industrial significance is unfortunate, and naturally many investigations have been conducted to improve our knowledge. In general, these investigations have revealed the complex nature of clay behavior and while sometimes they may not have seemed to contribute directly to a solution of the field operator's problems they have been of inestimable importance in bringing to light the broad fundamental scientific principles upon which must be based any effective working theory correlating the known facts of clay behavior and predicting profitable new lines of attack for its improvement.

Jan 1, 1938

Surface subsidence caused by coal mining operations was the subject of a very successful symposium organised by the Illawarra Branch of the Australas- ian Institute of Mining and Metallurgy in February, 1973. This symposium dealt with the principles of subsidence and overseas experiences arising out of underground mining. Since that time the i eew South Wales Department of Mineral Resources and Development (formerly the Depart- ment of Mines) has incorporated in the approval for pillar extraction certain conditions related to the monitoring of surface movement. Surveys and plans are required to be kept at mines where total or partial extraction of coal takes place. This paper traces the monitoring of surface movement in the Northern Coalfields of New South Wales over the past ten years. Reference is made to the National Coal Board's Subsidence Engineers' Handbook (1975) and how the guidelines expressed therein have been Beneficial.

Jan 1, 1980

"Mixing phenomena in a bottom blown air-stirred one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor was studie9-using three different configurations of straight circular nozzles fitted axially at the bottom of the vessel. The mixing time has been determined by pH measurements at various gas flow rates, bath heights and nozzle orientations in the presence and in the absence of a second phase.Experimental results reveal that the mixing time decreases with increasing gas flow rate. For a given gas flow rate the mixing time increases non-linearly with increasing bath height. Off-center configuration gives slightly lower mixing times as compared to center configuration. It is found that the contribution of buoyancy to the total stirring energy density is very small, but its contribution increases with increasing bath height. In the presence of an upper oil layer, the mixing time increases significantly for all configurations.IntroductionIn high temperature metallurgical melts mixing is carried out by injection of a gas either from top or bottom of the vessel in order to accelerate the rates of chemical reactions and to promote bath homogenization. When a gas is injected into a liquid through a submerged lance, porous plug or nozzle, the gas, rising as a two phase plume to the surface, imparts momentum to the surrounding liquid and causes gross circulation in the bath which promotes mixing."

Jan 1, 1997

By H. H. Schrenk, F. E. Griffith

"The increase in tunneling operations that requires working under pressures greater than that of ordinary atmosphere has raised the question of the use and possible limitations of respiratory protective devices under such unusual conditions. As little, if any, information is available, there is need for a comprehensive study of this subject before specific recommendations can be made. In the absence of such data it seems desirable to make a few preliminary observations regarding the problems associated with wearing respiratory protective devices under increased air pressures.Two distinct problems must be considered--the mechanics of the apparatus used under such conditions and the physiological effects of increased pressures on wearers of respiratory apparatus. This report is confined to the use of oxygen breathing-apparatus and gas masks under pressure.ACKNOWLEDGMENTSThe data presented were obtained at the Queens Midtown Tunnel under construction at the east end of 42d Street, New York City, during a study of compressed-air illness conducted by the Bureau of Mines in cooperation with the United States Public Health. Service and the New York City Tunnel Authority.Grateful acknowledgment for cooperation and the use of facilities is made to Dr. R. R. Sayers and his associates, particularly Dr. J. W. Crosson (who acted as observer during the oxygen breathing apparatus tests), of the Division of Industrial Hyiene, National Institute of Health; to the Port of New York Authority, through Dr. Edward Levy; end to the contractors, through Doctor Emery."

Jan 1, 1940