Search Documents

By Glenn E. Craig

The practical and effective pulp distributor here presented is believed to be of a completely new and innovative design. It was developed at the San Nicolas Plant of the Marcona Mining Company in Peru, where it has been thoroughly plant tested using iron ore slurries of a particularly abrasive nature. It has proven to be superior to the apparatus originally installed, or to any observed in operation elsewhere. In plant practice the capacity and efficiency of many process units such as screens, magnetic separators, and jigs are strongly affected by the loading pattern, and for better results the flow of pulp must be proportioned across the receiving lip in equal quantities per unit width. The distributors originally installed on the drum magnetic separators in San Nicolas proved to be unsatisfactory, and several trial modifications failed to show any improvement. As is usually the case, feed rates were being steadily increased, and appreciable losses to tailings resulted. A check of the distributors on the market discloses no reasonable substitute, so efforts were directed toward devising an entirely new type. Required was a positive type of action which would guarantee that the pulp flow be spread equally along the length of the drum. Discussion As indicated, the motivation for development was simple necessity. The plant in San Nicolas crushes, grinds, and concentrates magnetic iron ores of a particularly abrasive nature, and depends largely on magnetic separation to obtain a marketable product. Feed to the numerous drum magnetic cobbers and finishers varies from rod mill discharge at a nominal minus ten mesh to a ball mill fine grind of seventy percent minus three hundred and twenty-five mesh. Operational factors affecting the magnetic separators were well controlled,

Jan 1, 1971

By W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-element method for evaluating shaft pillar mining plans and shaft stability. This report focuses on mine measurements and calibration of the two-dimensional computer model and is the second in a series of three Reports of Investigations describing the Ross shaft study. In this study, borehole extensometers and other instruments were installed to provide data for model verification and to monitor the shaft. Results of the recalibrated two-dimensional model (UTAH2) confirmed the premining stability evaluation. However, after mining began, concern was expressed because cracks and other signs of ground motion appeared at considerable distances from the area of active pillar mining. In part 3 of the study, an intensive three-dimensional modeling effort using UTAH3 was initiated. The results again showed that the observed effects were within expectations and that the shaft would remain safe. Three-dimensional analyses of alternative pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought.

Jan 1, 2010

By E. V. Potter

"INTRODUCTION The oscillator and amplifier system described in this paper was developed specifically for driving sound generators of the type developed by H. W. St. Clair and described by him in an article 3/ published several years ago in the Review of Scientific Instruments.Nevertheless, with little or no alteration it can be used to drive any vibrating system in which the vibrating member must be driven at its resonant frequency; the only restrictions are that the driving mechanism be electrical in nature and that the vibrating member be accessible so that some type of pick-up can be coupled to it. Operation of the automatic frequency-control element in the oscillator, however, depends entirely on the operating characteristics of the vibrating member; therefore, in order to completely explain the operation of the circuit, it will be necessary to describe the construction and operation of the vibrator used with it. Only the essential features and characteristics of the vibrator will be described in this article, and the reader is referred to St. Clair's 4/ report for further details."

May 1, 1943

By S. J. Cohen

Changes in our energy, national security, and commerce needs have necessitated identification of new sources of minerals, such as rare earths, lithium, copper, silver, aluminum, titanium, and the minerals on the U.S. Geological Survey’s (USGS) list of critical minerals (USGS, 2022). With the need to domestically produce these minerals, more mining will be required within the U.S. Some of these critical minerals deposit with naturally occurring radioactive materials (NORM), therefore, mining these minerals may concentrate NORM to the point that some states may require licensing and radiation protection programs. NORM is not regulated by the Federal government; it is regulated by the individual states. Consequently, overall national state of NORM regulation is chaotic with each individual state either choosing to regulate or not regulate NORM, and, if a state chooses to regulate NORM, then that state develops its own unique regulations. Further complicating the regulatory environment, states utilize a wide variety of strategies for regulating NORM, which sometimes results in inappropriate regulations, inconsistencies with specific radionuclides that are regulated, and inconsistencies with specific NORM types that are regulated. This paper will review the nature of NORM regulations, identify regulatory traps, and provide general guidance for identifying NORM and potentially avoiding regulatory jeopardy. Because of the chaotic nature of NORM regulations nationally, seeking guidance from qualified professionals with relevant expertise is recommended. Also, contacting the appropriate regulatory agency to gain a complete understanding of the NORM regulatory environment is useful for maintaining compliance.

Feb 1, 2023

By G. J. Abbaschian, A. B. Gokhale, M. M. Kunjapur

"A laboratory scale model furnace was constructed for obtaining radially inward oriented columnar grains in disc shaped castings. The furnace consisted of eleven circular, concentric, equispaced resistance heaters on each half of a split graphite mold. Water or air flowing through a copper pipe along the periphery of the disc constituted the heat sink. After filling the mold, the heaters were turned off consecutively in top and bottom pairs from the rim towards the center, causing the temperature gradients to move inward. Equiaxed structure was obtained at the center by turning off the inner coils together when desired. Sn:15%Pb alloy was used to cast integral blade disc castings using the above technique to obtain dual-property discs with a central equiaxed structure and an outer columnar grain structure projecting inwards from the blades to the rim. A numerical technique was used to predict the temperature profile in the disc during solidification, and good correlation was obtained with the experimentally measured temperature profiles. The corresponding heat transfer coefficient values obtained were h = 544 Wm- 2k-1 (0.013 cal/cm2- ° C-sec) for cooling between metal and chill and h' = 71 Wm- 2k-1 (0.0017 cal/cm2- ° C-sec) for the heat input from the hot mold to the liquid metal. BackgroundHigh temperature alloys used in the current generation of gas turbine engines have evolved through two main stages of development: in 1950's, the increase in the efficiency of gas turbines was paced by improvements in alloy design, which led to the development of Ni and Co-based superalloys (1). By mid-1960's, it was realized that improved alloy chemistry alone was inadequate in meeting the increasingly stringent service requirements. The focus of research then shifted from alloy development to process development, and resulted in the introduction of directional solidification (DS) techniques for the production of turbine blades and vanes (1,2).Under typical operating conditions, the blades and vanes are subjected to aerodynamic loading, while the blades are additionally subjected to high centrifugal loading and vibratory stresses. The primary material requirements for blades may be summarized as follows (1,3):•,High creep resistance•,Good high temperature tensile strength (typically in the range of•,275 to 550 MPa at temperatures in excess of 750°C)•,Resistance to both low cycle and high cycle fatigue (LCF and HCF)•,Resistance to erosion, corrosion, and oxidation•,Resistance to thermal fatigue"

Jan 1, 1986

By M I. Pownceby, S P. Suthers, V Nunna, G J. Sparrow

Global demand for iron and steel has increased substantially over the past 20 years and there has been a greater focus on developing suitable processing options to treat low-grade hematite-goethite ores containing higher levels of silica and alumina impurities. The processing applicable to reduce the impurity levels in these lower-grade iron ores depends on their mineralogy and a thorough understanding of the process dynamics associated with the separation technology. Different separation technologies used to remove silica and alumina from low-grade iron ores were reviewed. The major concentration methods that may be applied to upgrade lower-grade lump iron ores include magnetic separation, wet and dry heavy media separation, and air-pulsed jigging. The technologies applicable to beneficiating iron ore fines include wet and dry gravity and magnetic separation, flotation, and roasting followed by magnetic separation. It is necessary to investigate the application of separation technologies on a case-by-case basis to select economically viable beneficiation strategies suitable for the particular low-grade iron ore. A commercial flow sheet is expected to involve the implementation of several separation technologies.

Nov 8, 2021

By Gregory Krohn

This report investigates the effects of adding a layer of extra padding to the palm area of leather gloves typically worn by low seam coal miners. The first study showed that added glove padding provides more potential protection but does not affect manual dexterity. The second study, in a simulated low seam coal mine, showed no significant differences using padded and non-padded gloves in crawling, shoveling, timbering, and cart pushing task completion times. In general, subjects preferred the padded gloves although they expressed some complaints about awkardness and loss of sensitivity. Recommendations are given for the design of padded gloves that will provide comfort, protection, and maximum hand sensitivity for miners.

Jan 1, 1980

By Graeme Lamson, Rene Dobbe, Merle Kalstrom, Janice Baron, Robert Thorpe, Chris Martin, Snezana Bajic, Amanda Palko

"This paper presents early results from a case study at the Mount Polley porphyry copper mine in British Columbia, Canada. Daily mineralogical data was acquired and reconciled with daily plant assay and recovery balances to interrogate the mineralogical controls on plant performance. After commissioning, the Minesite machine operated smoothly and reliably, creating daily data to generate mineralogical balances around the circuit for a period of several weeks. The key data, on final products were produced within 13 hours of the end of the respective operating period. The resulting information allowed for a greater understanding of the opportunities and limitations of the Mount Polley metallurgy. In this paper, how this information can be used to help long term strategic planning for the operation, as well as mine planning and production forecasting and the fine tuning of day to day mill operations is described. Early data available at the time of preparing this paper indicated that roughly 40% of the sulphide losses, or 32% of total copper losses existed as low grade inclusions in +75 micron tails. This represented the dominant form of long term copper losses, demonstrated repeatedly in the routine analytical data. However, on a day-to-day basis, the amount of copper present as chrysocolla is the major driver behind variations in total copper recovery. The degree to which this influences mill recovery is valuable to the geologist or mine planner. As they are armed with mineral speciation information for future ores, this will allow for improved mine planning, prediction of copper recoveries and production forecasting. The data was also started to find value in the mill by showing what caused sulphide losses. In the roughers, for example, the data showed poor recovery was the result of poor flotation performance and not any changes the speciation of copper sulphides or their liberation characteristics."

Jan 1, 2014

By George W. Leney

The iron ore industry might justifiably claim to have originated the science of geophysical prospecting. Their use of geophysical methods was probably the first application of these scientific techniques to the search for economic materials although the exact origin is undoubtedly lost in the unrecorded observations of. some prospector experimenting with compasses or bits of lodestone. Since 1879 when Thalen published "On the Examination of Iron Ore Deposits by Magnetic Measurements" these methods have been a standard supplement to other prospecting techniques. However, many of the great ore bodies of the Precambrian iron ranges were not particularly suitable for geophysical work. The ores were oxidized and enriched through leaching of silica so that they were nearly non-magnetic and other physical properties which distinguished them from the wall rocks were largely destroyed. With the gradual exhaustion of these high grade direct shipping ores, and ores that could be beneficiated by simple means, the iron ore industry turned initially toward the importation of similar high grade foreign ores. At the same time, new processes for concentrating lower grade materials were being developed and older ones improved upon. These concentrates' when pelletized produced such important savings in blast furnace hot metal costs that they now command a premium in the iron ore market and have weakened the competitive position of the remaining high grade ores. The ore bodies now being sought are usually unoxidized and frequently they are also metamorphosed.

Jan 1, 1965

By E. D. Gardner

The Synthetic Liquid Fuels Act (58 Stat., 190; 30 U.S.C. Sup., Secs. 321- 325) was approved by Congress April 5, 1944; it directed the Bureau of Mines to build demonstration plants to produce synthetic liquid fuels from coal, oil shale, and agricultural products. The most important oil-shale de- posits in the United States are in the Green River formation of Colorado, Utah, and Wyoming. The oil shale of western Colorado generally is more amenable to exploitation, more persistent, and apparently richer than elsewhere in the Rocky Mountain Region. It occurs at the top of a high plateau surrounded by bold, nearly vertical escarpments 500 to 600 ft in height. The top 400 to 500 ft of these escarpments comprises an oil-shale measure that averages 15 gal of shale oil per ton; the bottom 70 to 100 ft of the measure, called the Mahogany Ledge, averages over 30 gal per ton. The full measure in a 1000-square-mile area is estimated to contain 300 billion barrels of shale oil;' the Mahogany Ledge is estimated to contain 100 billion barrels of oil. These estimates are based on numerous surface samples and on core-drill holes drilled by the Government and by private enterprise. The oil-shale beds are undisturbed and lie nearly horizontal. The name

Jan 1, 1949

By Alistair James, James Alcorn, Chaitan S. Sandhu, Andy Small

The Risk-Informed Decision Making (RIDM) working group is a group of industry professionals formed under the joint initiative undertaken by United States Society of Dams (USSD), Tailings Dam Safety Committee and Canadian Dam Associations (CDA) Mining Dam Safety Committee (MDC). The working group was organized to develop a guideline on implementation of a RIDM process relating to the design of mining water dams and Tailings Storage Facilities (TSF). Since its formation in 2022, the group has completed a literature review of more than one hundred (100) cross industry publications on applications of RIDM in mining water dams and TSFs, has held two industry workshops in Niagara Falls, Ontario in 2024 and Saskatoon, Saskatchewan in 2025 to capture industry input relating to the understanding and application of RIDM. The working group has subsequently formulated a process that constitutes good industry practice as it relates to application of RIDM in mining dams and TSFs. The authors, through their engagement and leadership in the working group and facilitating the two industry workshops in 2024 and 2025, are of the opinion that the successful application process of RIDM across Canada and United States (U.S.) is still not clear to many industry practitioners. There is confusion over terminology, good versus poor RIDM, and in some cases reluctance to use the RIDM terminology. This paper addresses critical knowledge gaps identified in the RIDM implementation for mining water dams and TSFs through three years of stakeholder engagement. It provides clarity of the process via a joint position statement and implementation roadmap, resolves terminology confusion, and documents contradicting industry opinions to promote adoption of good RIDM practices in Canada, U.S. and beyond.

Feb 22, 2026

By Ruichen Ren, Xu Han, Caixia Li, Zengchuan Yue

In this paper, the size-density distribution of coarse middling coking coal (CMCC) with different grinding fineness and flotation concentrates was investigated. Then, the flotation behaviors and liberation characteristics of different size-density fractions in ground CMCC were analyzed, and the different size-density fractions were divided into five categories: mostbeneficial, secondary-beneficial, poorly liberated, insignificant-pollution, and serious-pollution. Based on the content of particles with different liberation characteristics, an evaluation index of the liberation characteristic of ground CMCC, namely, the liberation perfection index (LPI), was proposed. The results indicated that grinding changed the size-density composition of CMCC, which affected the flotation performance. Insufficient grinding and overgrinding were not beneficial to flotation. Insufficient grinding caused a higher content of poorly liberated particles and a lower content of most-beneficial particles. Overgrinding increased the content of serious-pollution particles and reduced the content of most-beneficial particles. The size order of the LPI values of different ground CMCC was consistent with the flotation efficiency, and the LPI values of the other two similar samples were overall positively correlated with their flotation performance, suggesting that the method is universal.

Feb 14, 2023

By J. A. Folinsbee, Andre Robitaille, Tony Y. Chong

"Conventional crushing and grinding is followed by gravity concentration to recover free milling gold. Refractory gold, finely disseminated within the pyrite and arsenopyrite matrix, is recovered by flotation followed by pressure oxidation, cyanidation, and cementation. Non-refractory gold is recovered by cyanidation/CIP processing.A comprehensive test program aimed at improving flotation recovery was initiated in June 1995. Plant testing indicated that flotation tails value could be significantly reduced using mechanical flotation cells. Based on these test results, a flotation circuit that incorporates one of the three existing flotation columns followed by mechanical scavenging and cleaning was developed. Detailed engineering was completed in September 1996. Construction started in February 1997 and was completed in 3 months at a cost of $3.2 million. An on-stream X-ray analyzer was installed to provide real-time arsenic and iron analyses and inferred sulphur value on some of the flotation streams.The new flotation circuit proved to be an instant success. Flotation tails values were reduced by 27%. Final tails solids and solution was reduced from 0.035 to 0 023, and 0.0014 to 0.0006 oz/ton Au, respectively. Based on a mill throughput of 1,620 stpd this decrease in tails value will result in an increased gold production of 7,500 ounces per year. The payback for the project is estimated to be around one year.This paper describes the evolution of the project from bench scale testing to commissioning. Also, the operational and economic impacts on down stream processing are highlighted"

Jan 1, 1998

By George Kazonich

The high costs and environmental problems associated with making iron and steel in the United States is driving the development of new technologies to replace the blast furnace. A prototype reactor incorporating rocket technology was designed and built. This rapid rate reactor was operated successfully and consistently made iron metal. Minus 325-mesh magnetite particles could be reduced to iron metal in less than 50 ms in a high temperature flow through reactor. Iron product was recovered inside the reactor and in a downstream cyclonic separator. The results of typical operation and how parametric changes affected the reduction of iron ore concentrates are discussed.

Jan 1, 1993

By C. C. Pretorius, S. Ramjee, R. J. Mostert

The study investigates the effect of prior corrosive exposure on crack growth resistance behaviour of thin sheet (3 mm thick) aluminium alloy 2024-T3 at slow strain rates. Compact tension specimens were exposed to standard corrosive environments that simulate accelerated atmospheric corrosion attack. Two corrosive environments were considered – an exfoliation corrosion (EXCO) solution and a 3.5 wt% sodium chloride solution. The unloading compliance R-curves of the two-hour EXCO-exposed specimens revealed a significant degradation of approximately 11% in the crack growth resistance behaviour (Kc_e values) compared to the baseline (air-exposed) values. Furthermore, secondary intergranular crack formation was also revealed in the plastic zone ahead of, and adjacent to, the crack tip of these specimens; which formed during the crack growth resistance loading. It is postulated that the observed degradation of the Kc_e values of the EXCO-exposed material is due to hydrogen embrittlement since the exposure times for the EXCO evaluation were limited to ensure that uniform corrosion dominated; that is, significant penetration of corrosion damage and pitting due to localized corrosive attack did not occur. The sodium chloride-exposed specimens revealed a similar degradation (13%) after 24 hours exposure. However, slight intergranular corrosive attack and isolated pitting were observed on the exposed surfaces prior to crack growth resistance loading, resulting in notch effects that could assist in crack growth. Pitting and intergranular corrosion were, however, not observed at the pre-crack tip. The relative contributions of the notch effects and the hydrogen embrittlement during the degradation of the KR performance are, therefore, unclear.

Apr 1, 2021

By Clarence Hall, Spencer P. Howell

Among the more important factors involved in the use of high explosives in blasting operations is the means employed to bring about the detonation of the charge. When flame is applied to high explosives many of them may burn if not confined; but all of them when burning under certain conditions of confinement may detonate. Detonation may also be effected by mechanical means, such as frictional impact caused by a blow or by rubbing between surfaces. By this means, however, the full effect of the explosive charge may not be developed, so that a partial detonation, often accompanied by the burning of the explosive, results. When nitroglycerin was first used it was fired by the application of flame, but considerable difficulty was experienced in exploding it with certainty and in obtaining uniform resl'llts. In 1864 Allred Noble, a Swedish engineer, discovered that nitroglycerin could be surely and completely detonated by exploding in contact with it a small quantity of an initiatory explosive. Mercury fulminate was the substance then found capable of producing the best results There are many other fulminates and other substances that will produce complete detonation of commercial" high" explosives, but detonators or electric detonators containing mercury fulminate as the characteristic ingredient are still almost exclusively used in this country. The term" detonator" is used in the publications of the Bureau of Mines to designate what the miner calls a "blasting cap "-a copper capsule containing a small quantity of some detonating compound that is ignited by a fuse. The term" electric detonator" is applied to a blasting cap that is similar except for being ignited by means of a small wire which is heated to incandescence or fused by the passage of an electric current. One of the conditions prescribed by the Bureau of Mines for a permissible explosive a is that it shall be :fired by a detonator, or preferably an electric detonator, having a charge equivalent to that of the standard detonator used at the Pittsburgh testing station. A further requirement is that this charge shall consist by weight of 90 parts of mercury fulminate and 10 parts of potassium chlorate (or their equivalents). At the request of a manufacturer of permissible explosives, an investigation was undertaken by the bureau to determine the relative strength of detonators and electric detonators having different compositions. The tests of electric detonators herein reported were conducted by H. F. Braddock, junior chemist; J. W. Koster, J. E. Tiffany, junior mining engineers; and A. S. Crossfield, junior explosives chemist, at the Pittsburgh testing station of the bureau. Similar tests of detonators were not conducted because it was believed that the results would not show sufficient variation to warrant such tests. It is hoped that the conclusions drawn from the tests made will be of service to those using explosives by enabling them to select the grade of detonator or electric detonator that will insure the most effective results. The conclusions are given in this bulletin, which is published by the Bureau of Mines as one of a series of publications dealing with the testing of explosives and the precautions that should be taken to increase safety and efficiency in the use of explosives in mining operations. The results of tho experiments described in this bulletin show that the average percentage of failures of explosives to detonate was increased more than 20 per cent when the lower grades of electric detonators were used instead of No. 6 electric detonators, and was increased more than 50 per cent when these lower grades were used instead of No. 8 electric detonators. It is noteworthy, however, that when sensitive explosives, such as 40 per cent strength ammonia dynamite (p. 33), were tested under conditions ideal for detonation, the same energy was developed irrespective of the electric detonator used. When tests were made with a less sensitive explosive, such as a 40 per cent strength ammonia dynamite containing nitrosubstitution compounds (p. 32), the energy developed increased with the grade of the electric detonator used. For example, the average efficiency of four different explosives was increased 10.4 per cent when a No.6 electric detonator was used instead of a No.4 electric detonator, and 14.9 per cent when aN 0.8 electric detonator was used (see tabulation onp.45). The results of the tests emphasize the importance of using explosives in a fresh condition, but as fresh explosives can not always be had in mining work, strong detonators should be used in order to offset any deterioration of explosives from age.

Jan 1, 1913

By W. M. Hart

The current Automatic Data Acquisition system developed by some support manufacturers makes it possible to continuously monitor and record changes in leg pressure and advancing ram stroke in every shield, and shearer position at any moment during the mining operation. In order to effectively use the massive data obtained from this system for improving production and maintenance managements as well as providing better roof control at a longwall face, the research currently conducted jointly by West Virginia University and Cyprus-Amax Coal Co. attempts to develop a Longwall Management System for mine operators. The LMS software package runs on a MS Windows NT environment and consists of four sub-systems: (1) Data Interpretation and Analysis; (2) Production Management; (3) Maintenance Management; and (4) Ground Control. This paper presents the details of each sub-system.

Jan 1, 1995

By Jose F. T. Agapito

The mining engineer must be able to predict the structural behavior of the rock around underground openings so that he can answer questions relating to safety and economics. With the present status of rock mechanics knowledge, exact predictions cannot be attained and approximate idealizations are made. As a first approximation, structural design makes use of theory, laboratory testing of rock properties, and available experience from excavations in similar rock formations. However, realistic design can usually be obtained only after in-situ observations and measurements are made. After all the information is collected, judgement and experience play a most important role in the final formulation of the design. This paper describes part of a geotechnical program which was instrumental in obtaining information for the design of large oil shale pillars. The work was carried out during 1971 and 1972 in the experimental mine of the Colony Development Operation. Colony is an oil shale venture formed between Atlantic Richfield Company, Operator, The Oil Shale Corporation, Cleveland-Cliffs Iron Company, and Sohio Petroleum Company to conduct research and development in mining and retorting of oil shale, The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 250 miles west of Denver (Figure 1) . Mining was conducted by the room-and-pillar method in a 60-ft high portion of the Green River Formation at a depth of 600 to 850 ft, Pillar dimensions are approximately 60 ft by 60 ft. The mine site is in the eastern face of the canyon containing the Middle Fork of Parachute Creek, The distance from the mine to the side of the mountain varies from 500 to 1,200 ft, and its height above the stream floor is approximately 700 ft.

Jan 1, 1974

By G. Récoché, A. Chamaret, M. O’Connor

Building indicators that respond to all stakeholders' needs is a time-consuming and complex exercise, with certain questions still unsolved. The aim of the current three-year research project, carried out in partnership between BRGM’s Mineral Resources Division and C3ED, is to propose a top-down / bottom-up indicators building methodology that combines conception and coordination methods and a participative approach. The tool-design phase is based partly on a comparative analysis of existing international initiatives according to different criteria (objective, observation scale, framework, etc.). The study of two African mining projects will provide the opportunity to confront the conceptual aspects with reality in the field. Careful consideration of the participants’ suggestions will result in a set of indicators that can be easily understood and adopted by all stakeholders. The final objective is to measure the impact of a mining site on a local, regional and national sustainable development frame, throughout the full life cycle of a mine.

Jan 1, 2005

By T Ireland

The Rosedale Outfall Project utilised an earth pressure balance (EPB) tunnel boring machine (TBM) for only the second time in Auckland. Although the tunnel was excavated fully through East Coast Bays Formation (ECBF), the downhill gradient along with some unexpected areas of extreme water posed some significant challenges during construction.The Rosedale Waste Water Treatment Plant Outfall Tunnel project was commissioned in response to the growing needs of North Shore City, New Zealand. The outfall tunnel comprises a 3 km long segmentally lined tunnel and a 2.1 km buried marine pipeline, and discharges 2.7 km offshore. The capacity of the new outfall is 6 m3/s compared to the existing outfall capacity of 1 m3/s.Following previous project experience, and with the tunnel located along its full length in the bedrock weak sandstone/siltstone bedrock of the East Coast Bays Formation, tunnelling conditions were expected to be benign. However during construction six high inflow events were encountered, including a full face (3.4 m diameter) of Albany Conglomerate over a 48 m length of tunnel. This material comprised cobbles in an uncemented sand matrix, and inflows were recorded at over 25 L/s.This paper describes the design challenges on the project including the design of a steel fibre reinforced segmental lining for internal pressures. The specification of the machine is discussed including the modifications required to enhance the risk mitigation measures already in place. The ground conditions encountered are discussed and have improved the knowledge of the range of conditions that can be expected in Auckland.Despite the challenges presented during construction, excellent progress rates were achieved and the tunnelling was successfully completed ahead of program.

Mar 8, 2011