Search Documents

By Rangaswamy. K, Naga Sivaji

A stone column is one of the most commonly employed methods of ground improvement techniques. This method used to increase the strength, decrease the compressibility of loose granular and finegrained soils. Also, it accelerates the consolidation in clays and reduces the liquefaction potential of sands and silt soils. In general, the stone column contains 15 to 75mm stone aggregates. In reality, it is not easy to avail the natural stone aggregates due to unavailability in locally nearby places. Present work aims to replace the stones partially or entirely by scrap tyre chips as an alternative material. The utilisation of recycled tyre chips in ground improvement is an environmentally friendly solution and avoid the disposal of tyre chip waste in large pits. Model tests conducted on marine clay with encased end bearing stone columns (ESC) constructed with a mixture of stone aggregate and tyre chips with sizes 4.75 to 10mm. The column diameter is 75 mm, L/d ratio maintained to 5.3. Non-woven geotextile wrapped encased stone column has introduced in the soft marine clay model. Encasement prevents the lateral squeezing of aggregates into the surrounding clay and protects the drainage function of the stone column. A set of load-settlement tests were conducted on both the clay model and clay model treated with the stones-tyre chips column. The model was loaded by the tri-axial loading frame. Shear strength parameters of stones and tyre chips were determined by large size direct shear tests. Model test results are concluding that the load-carrying capacity of the clay is improved significantly after installing the stone column in it. The encasement increases the load-carrying capacity and stiffness of the ordinary stone column. It is also proved that the stone aggregate could be replaced partially by tyre chips up to 60% without a significant reduction in its performance.

Nov 1, 2022

The purpose of this paper is to present validation studies of the mine-fire simulator using data gathered from an actual mine fire which occurred in November 1991 at the Pattiki Mine. To develop the model of the ventilation system with the fire in this validation study, the following adjustments were made: (1) flow and gas distribution in the entire ventilation network, and (2) fire parameters matching the data recorded by the monitoring system. After close correlations between simulation and real data were achieved, additional analysis of the ventilation system with the mine fire was performed. Presented and discussed in this paper are the following stages of the fire at the Pattiki Mine: (1) early fire (before the fire was detected), (2) preparation for and fire fighting with water, (3) fire sealing, and (4) fire extinguishing. This study evaluates the suitability of the computer software package for modeling underground fires. The paper also discusses the importance of the on-line monitoring system for the validation process.

Jan 1, 1995

By H. W. Gillett

BATTELLE Memorial Institute is an endowed in stitution for scientific research in metallurgy, fuels, and allied fields, established by the will of Gordon Battelle, 2nd, as a memorial to his father, Colonel John Gordon Battelle. Before I tell you more of what Battelle Memorial Institute is, I want to go back a bit and tell you why it is. Colonel Battelle began his services in the iron and steel industry in Wheeling in 1866 and in 1883 came to Ohio, where he successively engaged in the iron and steel industry in Cincinnati, Piqua and Columbus. The family had been prominent in Ohio affairs since 1788, when Gordon Battelle's great-great-grandfather came from New England to settle in Marietta. He was one of the pioneers and a member of the famous "Ohio Company."

Jan 1, 1929

By C. Ortuglio

The Bureau of Mines developed equations to determine the relationship of yields and products obtained from BM-AGA carbonization in 13-and l8-inch-diameter retorts. The developed equations indicate that results of carbonization in l8-inch-diameter retorts can be predicted from results obtained with l3-inch-diameter retorts.

Jan 1, 1966

There are many ways to classify structural slurry wall elements, but the DFI committee chooses to limit these descriptions to three functional requirements, namely: design function, plan configuration and type of panel reinforcement. (See Figure 1 in Part IV for panel classification). Slurry walls can function as: 1. Curvilinear or linear elements for temporary and/or permanent structures to resist lateral forces transferred from the ground, water, earthquakes and various surcharge loads. 2. Load bearing elements in various plan shapes to resist vertical forces. 3. Combination Elements to resist combined forces under conditions 1 and/or 2. For example, elliptical shafts with various openings for tunnels and conduits have been commonly used for deep excavations.

Jan 1, 2005

By John H. Bassarear

By 1968 Cyprus Pima was milling 38,000 tpd of copper ore using a conventional flowsheet consisting of three stages of crushing rod mills and ball mills. A 15,000 tpd expansion was put on stream late in 1971 using primary crushing, semiautogenous mills, and ball mills. Identical ore is treated in both concentrators. This paper shows the weight and life of each individual liner for each crusher and each mill over a four year period from 1974-1977. Power and media consumption are shown for the same period and a comparison is made between the two reduction methods.

Jan 1, 1980

By Nick Tessitore, Ryan Marsters, Alex Warren, Dylan Fawaz

The West Gates Deicing Industrial Waste Pond Expansion project at Denver International Airport seeks to expand utilities to accommodate additional terminal gates. The project includes six tunnel crossings beneath taxiways and runways with lengths ranging from 239 to 2,025 linear feet. Excavation methods include shielded tunnel boring machines and steerable auger boring. Designed initial support includes liner plate, steel ribs and lagging, steel casing, and Fiberglass Reinforced Pipe and ranges in size from 24" to 132". This paper will discuss challenges associated with the overall layout and design of the project, including contingencies to protect critical infrastructure. In addition, a construction update is provided.

Jun 23, 2024

By S. C. Torma

Sources of lead contaminated soils are numerous, i.e., the uses of leaded gasoline, lead-based paints, leaded pesticides, solders, smelting of lead concentrates, refining of lead products, automobile demolition, recycling of lead batteries, and so on. Conservative estimation by the US Environmental Protection Agency, EPA, indicated that several thousand lead contaminated sites are awaiting remediation. The current remediation technologies include immobilization, reclamation and soil washing. In this paper, the above remediation technologies will be reviewed, and where appropriate, the economics of processes discussed and future possibilities indicated.

Jan 1, 1996

By César Ugaz Castañeda, Paulo Fernández Alvarado, Richard Sotomayor Oblitas, Rocke Enríquez

Mina El toro has been making substantial changes in its operation to improve its social impact and productivity. Because of the use of gasified emulsions and electronic initiation system, it was possible to mitigate vibrations and carry out massive blasting, increasing its production by 4.2% and minimizing complaints from communities.

Feb 1, 2020

By Serdar Aktaş, Özgün Küçükoğlu, Burcu Nilgün Çetiner, Mehmet Hakan Morcalı

This study compares the cementation performance of metallic iron, metallic aluminum, and metallic tin in terms of the reaction conditions and parameters in synthetic antimony chloride solutions. The effects on the antimony recovery (%) caused by the cementators’ types, stirring speed, reaction time, and temperatures were explored thoroughly. The cementation kinetics of antimony were also explored for each cementator. The activation energies were determined to be 10.99, 9.09, and 13.58 kJ mol– 1 for Al, Fe, and Sn, respectively. The results reveal that the reaction is diffusion controlled, and comparable results were obtained for each cementator. At 25 °C, 40 mg of iron powder was found to reduce all antimony ions (i.e., approx. 99% recovery), but even when 100 mg of Al and Sn cementators were used, the antimony recovery did not reach 100%. This result shows that iron is the best candidate to cement antimony out of the solution.

Jan 28, 2022

By X Feng, X Zhang, W Sun, Y Zhe, K Hou, B Zhao, H Liu

Pulang Copper Mine, being China's largest newly built mine using block caving, boasts an annual production capacity of 12.5 million tons. Production level and roadway stability hold the key to the successful application of block caving. However, with Tong Kuangyu being the only mine in China which has applied such a method, we currently lack relevant experience in the successful application of the method. This paper has studied the influence of different rock mass zonings, fault thickness, fault dip angles, on-site construction quality on the production level, roadway stability of block caving through numerical simulation and analysed the roadway stability in different kinds of support solutions so as to ensure the successful application of block caving in Pulang Copper Mine. The results have shown that the existing support method in Pulang Copper Mine can meet the requirement of roadway support in zone II and III, but could not satisfy the demand in terms of support strength in the relatively fragmented zone I area. When roadway passes through the fault, the deformation of surrounding rock and plastic zone of roadway will gradually decrease with the increase of fault dip angle; the deformation of surrounding rock and plastic zone of roadway will gradually increase with the increase of fault thickness. An ideal support effect can be achieved through the joint support of grouting and bolting when roadway passes through the fault. In the measured model of on-site construction, there is stress concentration in the intersection between the access and transverse drift of ore removal. Therefore, the stability of the roadway can be improved by improving the construction quality. CITATION:Sun, W, Hou, K, Zhang, X, Feng, X, Liu, H, Zhe, Y and Zhao, B, 2018. Research on supporting technology for production level roadways of block caving in Pulang Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 95–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Marcus Vinicius Dias Garcia

O presente trabalho tem por objetivo contribuir para a preservação refratária de baterias de coque, apresentando uma metodologia de planejamento e controle. A condição dos refratários de baterias de coque é crucial para sua produtividade e para o cumprimento de diretrizes ambientais. São desafios (i) a identificação precoce de danos e previsão de seu efeito no desgaste global da bateria, para hierarquia de reparos; (ii) a seleção da técnica apropriada a cada reparo. No presente trabalho, os autores compilam o estudo da progressão de danos sob diferentes tipos de reparo ao longo de mais de 30 anos em baterias heat-recovery e convencionais, de diversos modelos construtivos, e o combinam a tecnologias de inspeção para consolidar uma metodologia de gestão da preservação refratária. A metodologia foi aplicada em baterias localizadas no Brasil, avaliando a condição de mais de 400 fornos em 90 dias. Para a bateria mais crítica, foi identificado um potencial de prorrogação de vida útil em torno de 10 anos.

Aug 17, 2017

By Shklyar FR, Bokovikov BA, Gordon YM, Scherbatskii VB, Yaroshenko YG, Shvydkii VS

The paper presents, for the first time, a complete mathematical model of the flow of gases in packed beds which describes the processes of gas-mechanics in iron blast furnaces and other shaft type smelting units. Good correlation between calculated and experimental results was obtained confirming the adequacy of the model. It is shown that the uniformity of gas distribution is related to the tuyere size and the extent of its protrusion into the furnace and that these variables may be used to regulate gas distribution across the furnace diameter. It is also concluded that furnace height has no significant influence on gas distribution. The necessity for a mathematical description of raceway phenomena has been experimentally proved. Conclusions from theory are shown to have profound implication to furnace design and operation.

Jan 1, 1975

By N. A. Eilertsen

The Aroostook manganese-bearing deposits lie within a rectangle 30 miles wide and 70 miles long. Over 40 different deposits have been discovered in this area, but they have not been mined because the ores are difficult to treat. In 1949, the Maple Mountain area was selected for detailed investigation by the Bureau of Mines, because study by the State of Maine and the Federal Geological Survey indicated that it was the most promising in Aroostook County for developing a large tonnage of reserves. Investigation by the Bureau of Mines disclosed that all of the reported deposits of the central district were located on the limbs of a syncline underlying a pear-shaped area of 283 acres between the crests of Maple Mountain and Hovey Mountain. The ore area has been outlined by trenching and drilling along three sides of the perimeter, while the remaining side is defined by a fault. The area has a length of 6,300 feet and a maximum width of 3,100 feet. Diamond-drill holes have intersected the deposit as deep as 1,550 feet below surface, but additional deep drilling would be required to determine the intensity of folding or warping at depth. The Maple Mountain-Hovey Mountain deposit lies in the slates of Ordovician age and is classified into three zones, of which the upper, averaging about 57 feet thick, is designated manganiferous purple and red slate. The central zone, also averaging about 57 feet thick and containing the highest manganese content, is manganiferous, banded hematite. The lower zone is manganiferous, interbedded hematitic and green slate with an average width of about 33 feet. Manganese minerals occur with hematite in all three units. Trenching on the northwestern slope of Hovey Mountain uncovered other disconnected deposits of manganiferous rocks of earlier age than the ore of the syncline. The general strike of these deposits, which range from 15 feet to 75 feet in thickness, is southwest a length of 5,000 feet. They dip steeply southeast. The ore of the syncline is predominantly deep, hematitic red, inclining to red-dish black, fine-grained, dense, and thinly laminated. It is hard and siliceous. Hematite has, in places, been altered to magnetite. Because of the fine-grained texture of the ore, the manganese-mineral constituents are difficult to determine. Of the manganese silicates present, braunite is the most readily identified. Manganese carbonates and oxides are found also.

Jan 1, 1952

By Peter Grandstone, D. A. Jessup, D. B. Taliaferro

"INTRODUCTION Water flooding of oil sands in Texas as a means of secondary recovery of oil has been practiced mainly in the north-central part of the State, which includes the old shallow fields in eight counties, extending south through Wichita and Clay Counties on the Red River into Brown County.The Texas Railroad Commission, is empowered ""to promote conservation and prevent waste in the drilling, completion, operation, and abandonment of oil wells"" and ""to issue regulations necessary for fulfillment of these ends,"" granted The Texas Co. the first permit to inject water into the oil-bearing sand on December 7, 1935. The permit was granted after the Commission had conducted a number of hearings, which were attended by many operators interested in that method of secondary recovery. Through December 31, 1944, the Commission had granted 50 permits for water flooding. Of that number, 45 permits were issued for projects in north Texas, the remaining 14 being distributed throughout west and south Texas. By the end of 1944, there were 33 active and 5 abandoned water-flooding projects in the North Texas area, as is in figure I.Oil production in the North Texas area started in 1904 from the shallow sands (ranging from 100 feet to 800 feet in depth) of the Petrolia (or Henrietta) field in northern Clay County. Development was rapid and unrestricted during the boom period from about 1911 to 1918, and considerable waste of both produced oil and reservoir energy resulted."

Jul 1, 1946

By J. J. Drost

This Bureau of Mines investigation studied the effect of thermal treatments upon concentratability of a western Mesabi Range nonmagnetic taconite ore and is a sequel to Bureau of Mines RI 7567. Magnetic tube tests were used to develop the data needed to calculate separation efficiency, the primary measure of concentratability. A horizontal tube furnace was employed to heat treat and reduce the hematitic ore samples. The two variables studied were roasting temperature and cooling method. The manner of cooling, either by slow cooling or quenching in water, produced no significant difference in concentratability. Roasting temperatures employed ranged from 500° to 1,000° C, and a temperature of 650° C effected the best concentratability. The temperature of 650° C correlated with the most effective roasting temperature for grindability.

Jan 1, 1973

By Sydney H., Ball

ONE of the important mineral discoveries of the eighteenth century was , that of the Minas Geraes, Brazil; diamond fields. The production of this and of .other diamond discoveries in neighboring states made Brazil the premier producer of diamonds, succeeding India; its 140 years of supremacy finally passed to- South Africa- 60 years ago. Three times have diamonds contributed heavily to Portugal's somewhat checkered financial history; first in the sixteenth and seventeenth- centuries when the diamond trade of India was controlled by its citizens residing in ,Goa, later in the late eighteenth and the first 75 years of the nineteenth century when the Brazilian fields were the world's source of diamonds, and now, when the Angola diamond mines are the principal source of revenue of its colony, Portuguese West Africa. Certain phases in the history of the administration of the Brazilian field are sufficiently curious to warrant description.

Jan 1, 1929

By Paul Culvenor, Brad Gyngell

Ensuring effective management of contractual processes is essential for maintaining profitability and operational efficiency in mining. However, due to limited capacity and resources, sites often struggle to manage these processes effectively, leading to oversights and financial losses. Recent advancements in Artificial Intelligence (AI) offer promising solutions to these challenges. Large Language Models (LLMs), like those powering ChatGPT, now enable machines to understand unstructured data like contracts. These can therefore be applied to address these challenges by taking some of the heavy lifting off of humans. In this paper, we analyze a real-world case study of the application of LLM tools for preventing a $400k contractual issue on an underground gold mine in Western Australia. We provide a gap analysis of the failure modes in existing processes that led to the issue. We then describe the application of LLM tools to flag it early and facilitate a collaborative solution between the operator and the supplier. This includes a comparative analysis of base case vs LLM case to evaluate the impact on project cost and time. Finally, we discuss how the integration of AI can foster improved relationships between clients and contractors across a broad range of potential contractual applications, allowing the time required for collaborative and proactive problem solving.

Feb 1, 2025

By E. Oshima

The only one reverberatory furnace smelting in Japan has been alive in Onahama Smelter, Onahama Smelting and Refining Company. The fuel for the reverberatory furnaces had been changed from bunker C-oil to mainly coal and partially waste tires to reduce the energy cost. The steam, recovered by the waste heat boilers of the reverberatory furnaces, has been utilized fully for the power generation to save the purchase power. Copper concentrate has been smelted also by injection through tuyeres in the P.S. converters since 1983. The amount of concentrate, treated in the converters, was increased by the construction of small oxygen plant in December, 1990. In the paper, the current practice and improvements in the reverberatory and converter operations are described.

Jan 1, 1993

By Dwayne D. Tannant

The Adra tunnel near Naramata BC experienced a fire in 2010 that burned timber sets within the tunnel and caused severe spalling of rock from the roof and tunnel walls. The nature of the damage is documented and efforts completed to rehabilitate and open a portion of this tunnel to the public are described. The use of shortcrete and rock bolts is a technically and economically superior support system to timber sets as well as being far more fire resistant.

Jun 1, 2012