Search Documents

By K. J. Henderson

INTRODUCTION Shrinkage mining at Inco Ltd.'s Crean Hill mine can best be defined as a horizontal breasting method utilizing the broken ore for the mining floor and to provide wall support, with draw from a series of boxholes or draw¬points at the base of the stoping block. In choosing to shrink a given block of ore, the initial investigation centers on the ore configuration and grade, the expected ground conditions in the stoping area, the expected profit compared to alternative mining methods, the future production requirements, development lead time, the availability and type of equipment in the area, and the availability of experienced miners. These factors are weighed against other mining methods and shrinkage mining is chosen when the advantages outweigh the dis¬advantages. These will be discussed in more detail later. At Inco Ltd.'s Crean Hill mine, shrinkage mining makes up 17% of total mine production and is decreasing due to the advent of advanced blasthole techniques, notably in-the-hole drilling. Shrinkage is an adaptable mining method that is currently employed in narrow irregular ore zones, as undercuts for in-the-hole blast¬hole stopes, in ore bodies that do not extend from level to level, and in areas where quick production is required with a minimum of capital outlay or minimum develop¬ment. Two major types are currently in use which are classified on the basis of type of draw system employed. These are the utilization of load-haul-dump (LHD) equipment drawing from drawpoints, and the slusher and train method drawing from boxholes into a slusher trench and loading into a train. A third method being phased out is drawing from chutes directly into a train. In all three methods the actual stoping operation remains the same. In the initial planning of a mining block, the ore body is first located using an exploration diamond drill¬ing program. This is essentially done at a 130-m (400¬ft) spacing and it gives an indication of the amount of ore, grade of ore, the configuration of the ore body, as well as other geological features such as ground condi¬tions which will affect future mining. This drilling is done from an exploration drift 165 m (500 ft) long in the hanging wall and covers a vertical extent of 330 to 670 m (1000 to 2000 ft). However, these data are not accurate enough for detailed planning. When the de¬cision has been made to mine, a preliminary develop¬ment drill drift is driven in such a position that it can serve the dual purposes of allowing the ore body to be drilled off in detail, or of later serving as a haulage or access drift. Diamond drilling from this drift is usually on a 15-m (50-ft) grid spacing and gives adequate information for detailed planning. Utilizing the drill data, a decision is made on the mining type. For a shrinkage operation, the stoping block is ideally 49 m (150 ft) in length and a maximum of 13 m (40 ft) in width. Lengths of 65 m (200 ft) are considered a practical maximum because of the length of time the back of the stope remains open during the min¬ing of a cut. A minimum length of 13 m (40 ft) is used because the amount of time spent in opening a new cut increases in comparison with the total stoping time. The maximum width of 13 m (40 ft) is used because ex¬perience with the ground indicates that generally stope backs tend to be unstable over greater widths. However, widths of 33 m (100 ft) have been mined. A minimum width of 5 m (15 ft) is used to allow an effective draw, but in unusual cases, a width of 3 m (10 ft) has been mined successfully. The dip of the ore should not be less than 1.04 rad (60°). Angles flatter than this will not pull properly resulting in inefficient mining because of ore hang-ups on the footwall side of the stope and the need for large stagings on the hanging wall. In considering shrinkage, mining ground conditions play an important role. Strong shearing, cross faulting, or dikes are avoided. These usually cause dangerous mining conditions and an alternative safer mining method which will give adequate support to these adverse ground conditions is employed. Production requirements are taken into considera¬tion when planning a shrinkage mining program. In it¬self, shrinkage mining is capable of producing ore in a relatively short time with little capital development. If quick production is required, this method can produce ore rapidly as all that is required is that the draw system be completed and the miners with jacklegs and stopers produce a limited amount of ore. The obvious disadvan¬tage is that not all the ore broken can be pulled from the stope immediately. However, a mining horizon with sev¬eral shrinkage stopes in different stages of production can adequately maintain scheduled tonnage require¬ments, the cycle being stopes under development, stopes actively mining, and stopes completed and pulling. When the decision has been made to use shrinkage mining in a given block, the haulage and draw system is driven. The proximity of the orepass system dictates whether the system is to be a LHD operation or a slusher trench operation. If the orepass system is in close prox¬imity to the stoping block, LHD equipment is employed because of its ability to operate efficiently over short haulage distances. A long tram to the orepass usually dictates a slusher trench operation with haulage by train. Internal orepass systems are used effectively with LHD equipment with a load-out and retramming taking place on a lower horizon. In addition, stoping blocks in older areas of the mine are developed track because of the capital cost involved in converting an existing level to trackless mining. DRIFT DEVELOPMENT USING LHD EQUIPMENT The haulage drift for a draw system using LHD equipment is driven parallel to the ore body in the foot¬wall at a sufficient distance to allow an 11.5-m (35-ft) drawpoint to be driven into the ore (Fig. 1). The actual position of the drift depends entirely upon the ore con¬figuration and the drift size depends on the equipment to be used. Drift sizes of 4.6 x 4.1 m (14 x 121/2 ft) for an St-4 and 3.8 x 3.6 m (111/2 x 11 ft) for an St-2 meet company and government clearance standards and allow sufficient space to accommodate a ventilation pipe. The

Jan 1, 1982

By S. M. Shelton

The widespread occurrence of domestic manganese deposits and the shortage of ferromanganese-grade ore have been sources of much speculation and investigative effort for many years. The present emergency has intensified the search by the Bureau of Mines for methods of producing ferromanganese-grade concentrates4/ from low-grade ores.

Jan 1, 1941

By S. M. Shelton

[The widespread occurrence of domestic manganese deposits and the shortage of ferromanganese-grade ore have been sources of much speculation and investigative effort for many years. The present emergency has intensified the search by the Bureau of Mines for methods of producing ferromanganese-grade concentrates4/ from low-grade ores.]

Jan 1, 1941

By H. D. Hess, C. P. Mabie

This report describes in detail the results of petrographic research conducted on 21 phosphate ores representing important deposits in southwestern Montana , southeastern Idaho , and northeastern Utah . The ores are described and categorized by mineralogical and chemical composition , thermal behavior of organic carbon , and textural constitution . Descriptive and genetic classification schemes applicable to western phosphate ores are discussed ; results from related studies made of the collophane mineralogy are also presented . The latter studies were centered on determining unit - cell dimensions and CO₂ , P2O5 , and fluorine content of collophane concentrates of 11 high - grade phosphate- rock hand specimens selected solely for this purpose . On the basis of this investigation , operational methods have been developed for quantitatively describing textural and compositional features that are likely to be significant in determining the response of phosphate ores to conventional beneficiation treatments ; systems for classifying the ores in relation to these features have been proposed . Studies to date point out distinct textural and compositional variations in the western phosphates and illustrate their importance in determining optimum beneficiation procedure .

Jan 1, 1964

By Peter K. Eriksson

Nanofiltration is very efficient in separating heavy metals from water solutions, even if they contain strong acids. Desalination System, Inc., has many years of experience in this area, and this paper deals with three different such cases. The first case deals with concentrating the heavy metals in the pregnant leach solution from a copper dump leaching site with a surplus water problem. The increased copper concentration in the pregnant leach solution increases the capacity of the following copper extraction stage. The nanofIltration permeate is polished with a biomass adsorption column to remove the small amounts of remaining heavy metals, before being discharged. This method eliminates sludge handling and disposal, which are quite costly with the alternative precipitation process. In the second case, a complicated precipitation method was used to remove heavy metals from the waste stream of a specialty metals manufacturer. Nanofiltration was installed to increase the metals concentration four times, which greatly simplified the precipitation process. The chemical consumption and sludge production decreased by more than 80 percent, and the labor cost decreased by 66 percent. In the third case, nanofiltration was used to purify waste sulfuric acid solutions containing heavy metals, to meet the specifications for technical grade acid. Sulfuric acid concentrations above 30 weight percent were successfully purified in a multiple pass membrane system.

Jan 1, 1996

By J. Iannicelli

Kaolin, normally an inert filler when compounded with polymers, is converted into a strongly reinforcing pigment by prereaction with certain functional silanes. Modification of kaolin with amino and mercapto silanes allows it to form crosslinks and confers significant improvements in modulus, abrasion resistance, compression set and other physical properties of a broad range of polymers.

Jan 1, 1990

By E. Hinton, L. Bloomquist

"This paper describes a guidance system for autonomous underground mining vehicles, which does not require any infrastructure or inertial positioning systems to aid the guidance process.BackgroundINCO Limited mines approximately ten million tons per annum through 12 operating mines in the Sudbury, Ontario, area (Fig. 1). With challenges from operating in a cyclical marketplace as well as new technologies making alternative nickel ores more competitive to refine, the Mines Research department embarked on a strategy that pointed toward automation as a tool to help the company become even more economical in mining.The mining industry has been looking for ways and means to mine orebodies more and more inexpensively. Automation and the lessons learned from manufacturing had a great influence in the direction of research at INCO Limited over the past ten years. Guidance systems have evolved over the years but the majority of commercially available systems rely on some form of infrastructure. This, in part, has caused some resistance from operators to install and maintain automated or semi-automated systems for guidance of underground machinery.Internal industrial studies cited travel time to and from the workplace as one of the major time sinks in the shift of underground miners. Depending on the mine, it may be as much as two hours moving in and out of an area. Some work areas have accommodated this by having “hot changes” at the work place. However, at some point in time, there are two people tasked with the same job and on site at the same time to make this overlap occur.Tele-operation of underground hard rock equipment eliminated this overlap and also provided a comfortable environment in which to work. By taking advantage of the communications network installed, the miners proved that they could operate three machines with relative ease. This was accomplished by a vision-based, “painted line,” autonomous guidance system termed the light rope system.With a few years’ experience with the system, some issues have arisen, including the cost of the rope itself (Fig. 2).The vehicle’s route is limited to the paths defined by the light rope, and a system of switching power to the light rope to select different routes is required. The rope itself is subject to damage from nearby blasts. Also, the system offers no obstacle detection; the vehicle may be switched off as a means of shutting the machine down thus protecting personnel in the area."

Jan 1, 2001

By Champoux. G., E. Ghali, W. Zhang, G. Monteith, A. -M. Lafront, G. Houlachi

The efficiency of the electrowinning process of zinc depends on the performance of oxygen evolution reaction, anode quality and corrosion resistance of lead anodes. Original surfaces of rolled commercial lead-silver anodes were examined using conventional polarisation methods in acid zinc sulfate electrolyte with manganese sulphate at 38 °C. The self-discharge method (potential decay) following 5 h polarisation at 50 mA cm-2 was considered to evaluate electrochemical activity, oxygen overpotential and anode stability. The influence of silver content is compared to that of the microstructure, the fabrication process and the composition of the corrosion products. Polished anode samples have also been examined for microstructural and corrosion performance studies. The experiments show that the duration of the plateau at 1600 mV versus SHE, the potential level (active corrosion state/stationary state) and the rate AEco/At during the decay could be a good indicator to compare the corrosion rates of the anodes in industrial zinc electrolytes.

Jan 1, 2008

By B Tessier

Checking the quality of a blast may be considered as subjective. Checking this quality will require measuring objective parameters. One of them is the resulting fragmentation of the blasted product. Numerous fragmentation æmeasuringÆ systems have been developed and marketed, based on image-processing. This presentation of FragScan will illustrate advantages and difficulties when using such a system. FragScan is essentially defending a policy of large and representative sampling. The purpose is to show how fragmentation is discriminating both productivity and profit of quarry operations on a blast-by blast basis. The next step will then be to ædriveÆ the blasting process to reach a æbetterÆ fragmentation. Other applications require the fragmentation as an essential result: this is the case for large boulders used in structure-reinforcement. Several case-studies have shown that FragScan can be used for quality-control, checking size-distribution of the product according to the requirements of the end-user. Only clear thinking about the precise use of such a æmeasurementÆ will further the success of this task.

Jan 1, 2001

By N. E. Hanna

As part of a program for improving, the safety of permissible explosives, the Federal Bureau of Mines has undertaken an investigation to establish the ability of sodium chloride to reduce the incendivity of permissible explosives to firedamp atmospheres. A motivating influence for this investigation has been the comparatively extensive experience of British and other European investigators, who used sodium chloride as a component of their permitted explosives (1, 5, 6 7).5/ In the United States research and development work of this type has been less extensive, although sodium chloride has been added to permissible explosives as a cooling agent (9) for many years. The results of the first phase of this investigation were presented in a previous paper (8), which established that adding up to 10 percent sodium chloride to permissible explosives reduces the likelihood of ignition of firedamp in the gallery test; however, the results were somewhat inconsistent, and the conclusions were qualified. Accordingly, the investigation was continued with a study of the effect of added sodium chloride as a function of the quantity added and of the particle size of the salt.

Jan 1, 1960

By Chester A. Fulton

SUPPLYING as it does a necessity for healthy animal and vegetable phosphate production is a most important industry. We human beings also are animal as this war so surely proves. Unlike many other elements no substitnite is available for phosphorus or its compounds. Marvelous as are modern plastics none can lake the place of phosphorus in making hone structures. As meassured in these times the phosphate industry is not a large industry. Output of phosphate rock, the original source of our agricultural and ,chemical phophates amounts to only some twelve million long tons per annum in the entire world. Phosphates are compounds of phosphorus, which is always found in nature combined with other elements. It never occurs in nature as such. The first choice of the element phosphorus is tie itself strongly to oxygen and then to water moisture - thus becomeing phosphlic acid. This phosphoric acid in turn hunts around for a base such as lime for instance and together they make phosphate of lime.

Jan 1, 1944

By D. W. Mitchell

This Bureau of Mines report summarizes experience and past research on methods for sealing abandoned areas of a coal mine and areas from which the pillars have been wholly or partially extracted. The Federal Coal Mine Health and Safety Act of 1969 requires that such areas be ventilated or sealed with explosion-proof bulkheads, but the present study indicates that bulkheads alone cannot isolate areas in a coal mine in which methane and other dangerous gases have accumulated. Gas-air exchanges between sealed and open areas must be controlled.

Jan 1, 1971

By James P. Bennett

EAF slag chemistry and its control have been recognized as important in producing quality steel at a low price for a number of decades_ EAF steel producers make lime and dolomite additions to furnaces, controlling the CIS ratios and sulfur pickup from the steel. Existing phase diagram data at 1600°C for CaO, MgO, FeO, SiO2, and Al2O3 was used to write a computer model optimizing slag chemistry for slag foaming and reduced refractory wear. The model, its development, and its use in an industrial steelmaking environment will be discussed along with how the model can improve energy efficiency. The importance of EAF mass balance to account for critical materials like Si in scrap and refractory wear using the model will also be emphasized_

Jan 1, 2003

By T. Shellhammer, A. Park

Among all pure metals, copper has the second highest thermal and electrical conductivity, next to silver. These properties coupled with a reasonable cost, make copper ideal for use in metallurgical vessels as a conductor of electrical current, as well as a lining material and protector of refractories and steel superstructures. Treatments of copper to address it’s softness and low melting point, specifically hard surfacing and calorizing, will be discussed. This paper will cover the evolution of copper to its current form, offer comparisons to other materials, and theoretical and empirical evidence on its superior performance in metallurgical vessels such as blast furnaces, basic oxygen converters and electric arc furnaces. Some case studies will be provided and finally a brief summary.

Jan 1, 2015

By E. C. Baker

Costs of disposing of steel slag are estimated based on the present method and a proposed alternate method for a steel mill in the Pittsburgh area. Estimated cost data were calculated by the Bureau of Mines and do not reflect the investment and operating costs and credits of a specific steel mill and processing plant. The alternate method of steel slag disposal would result in an appreciable cost savings to the mill and concurrently supply the industrial and commercial markets with low-cost, high-quality construction materials.

Jan 1, 1970

By W. H. Renison

This paper will discuss the operation and maintenance of Molycorp's Quests Mine ore conveyor system. The 1.2 m wide, steel cable-reinforced conveyor belts are capable of transporting 1089 kt/h of ore over a belt line distance of 3124 m with a vertical rise of 518 m. A portion of the conveyor runs in a 2057 m long underground decline on a 10° slope. Six 448 kW motors power the main 1.2 m wide belts.

Jan 1, 1984

By D. Robert Weir

The complex mineralogy of the Porgera resource has a pronounced effect on process selection for the recovery of refractory gold and silver. Intimate association of gold with pyrite necessitates a high degree of sulphur preoxidation in order to achieve acceptable levels of gold recovery. Acid pressure oxidation has been demonstrated to be the only commercially proven process capable of achieving the required level of pyrite oxidation. Gangue mineralization dictates preconcentration of the sulphides to limit the acid consuming capacity and carbon dioxide generation during oxidation. However, the relationship between concentrate sulphur grade and gold recovery to concentrate ultimately governs the optimum degree of sulphide preconcentration.

Jan 1, 1986

By Surendra K. Mishra

With increasing regulatory pressure from the environmental authorities, waste management has become a focal point of industrial operation. To offset the waste management costs, industry has made conscious effort to recover usable resources from the waste streams. This paper reviews the technical developments and current practices in processing of waste materials. Methods for recovering metallic, non-metallic and organic species from solid wastes and effluents generated by operating plants are discussed.

Jan 1, 1997

By O van Baalen

The Ernest Henry Mine is a copper-gold open pit operation situated in northwest Queensland, Australia. It is owned and operated by Xstrata Copper, with a current throughput of 11 Mtpa, however, open pit operations are scheduled to cease in mid 2011. The deposit dips approximately 45º and extends for at least another 400 m vertically below the final 530 m deep pit design.Construction and development of a sublevel caving (SLC) operation beneath the open pit was approved in December 2009. The feasibility design requires 39 km of development to be completed prior to production, which will commence in the fourth quarter of 2011. Initial ore production will be trucked and will increase to 3 Mtpa by the end of 2012, after which a hoisting shaft will be used. Ore production will then increase to 5 Mtpa in 2013 and ultimately to 6 Mtpa in 2016.Two 3000 kilo watt of refrigeration (kW(R)) modular refrigeration plants will be installed, as well as two 1600 kW mixed-flow fans capable of a combined flow rate of 780 m3/s at a total pressure loss across the mine of 2000 Pa. The main fans will be installed underground and will exhaust into the base of the pit.The following challenges were faced in the development of the ventilation and refrigeration network:•a relatively steep geothermal gradient,•tropical ambient conditions,•working under a wide pit shell, and•a large underground trucking fleet prior to shaft commissioning.A considerable number of ventilation studies were conducted with later studies extensively using Ventsim Visual™ mine ventilation software to complete the design process of the ventilation and refrigeration networks, including the comparison of several alternative designs. The paper focuses on design challenges prior to the commissioning of the hoisting shaft, and discusses resistance optimisation and occupational hygiene-related design parameters, such as heat and diesel emissions, production level ventilation, main fan selection and location, and refrigeration requirements.

Mar 21, 2011

By Norman Paley, Zachary Pickett

The Red Dog Mine is a high-grade zinc-lead mine located in northwest Alaska which began operations in November 1989. In June 2014 the upper half of a charge in a trim shot in the Aqqaluk pit deflagrated. No other holes in the area were observed to react and the remainder of the pattern was shot without incident. This was the only known case of a deflagration in the 25 years of operations. As part of the investigation into the cause of this incident rock samples were obtained from the area of this hole and from other areas in this pit.

Feb 1, 2020