Search Documents

By Charles H. Tiernon

Separation of particles on a table deck* results from differences in specific gravity, plus a number of other interrelated phenomena: size of particles; shape of particles; stratification (consolidation trickling); and hindered settling. The effective use of these factors may be controlled and aided by the following table adjustments: differential action of the drive or head motion; speed of motion; length of stroke; side tilt; end elevation; size of deck area; shape of deck; character of deck surface; riffle design; amount and distribution of wash water; feed water-to-solids ratio; feed rate; and feed uniformity. The typical concentrating table used in the US coal industry is essentially a rhombohedral-shaped deck supported by a suitable subframe. It generally slopes in the direction of the short axis, tilts upward at the refuse end of the long axis, and is differentially reciprocated in the direction of the long axis. This head motion tends to move the particles longitudinally toward the end of the table. At right angles to this movement, wash water (distributed along the high side of the table) tends to move particles down the slope parallel to the short axis of the table. Hence, the natural path of a particle on a concentrating table is from the feed box corner to the diagonally opposite corner of the deck (Fig. 1). There is a natural tendency for heavier particles to sink to the deck of the table and for lighter particles to stay nearer the surface. As a consequence, the heavier particles are carried further along the longitudinal axis since, being on or near the surface of the deck, they are more affected by the table's reciprocating action. The lighter particles, being at or near the top of the moving bed, travel slower in a longitudinal direction and thus separate from the heavy particles. Wash water and the diluting water in the feed cause lighter gravity particles to move down the short axis of the table. The feed material then fans out from the feed box, where it enters onto the table with heavy gravity particles moving in one direction and lighter particles moving in another. By properly adjusting all of the previously mentioned factors, a clear-cut separation is possible between high- and low-gravity particles, or between refuse and coal. Riffles are of great importance to tabling. They create considerably more capacity than is possible with smooth decks, and they are responsible for better separation accuracy. Particles in their downward movement along the deck's slope are delayed behind the riffles. Hindered settling, consolidation trickling, and other phenomena occur as the particles tumble over the riffles and stratification ensues. The heavier particles settle to the deck of the table and are trapped behind the riffles, thus insuring their positive movement toward the end of the table. Since stratification and separation of particles are not complete as a result of any one riffle, a series of riffles are used. The cycle of stratification and hindered settling is repeated from riffle to riffle. The result is purer products as particles fan out and progress forward and downward over the table. The smallest, heaviest particles stratify downward to the surface of the deck more quickly and are carried out by table movement toward the refuse end at a faster rate than coarse, heavy particles. Light gravity, larger pieces ride on the top layer of particles and flow down the deck's slope as a result of the cross flow of wash water at right

Jan 8, 1980

By Stephen Zorn

INTRODUCTION The process of financing mining projects in developing countries has changed greatly in the past 15 years. New methods of financing, notably the use of syndicated Eurocurrency project loans, have appeared, and direct equity financing by transnational mining corporations has become less significant. These changes are of particular importance to developing countries which have many mineral deposits still awaiting development, or even discovery. If major new mines are to be financed, host governments will need to obtain more sophisticated information than has hitherto been widely available as to the various sources of finance currently available and as to possibilities for innovative approaches to financing, such as the combination of several different kinds of financing in a single package. This paper reviews the major sources of mining finance potentially available to developing countries and highlights those problems in obtaining adequate financing that developing country producers have begun to experience in the last few years and that are likely to persist through the 1980s. Section I surveys the major types of mining finance; section II reviews specific financing problems, including (a) the withdrawal of the transnational corporations from developing countries, (b) inflation and the size of new projects; (c) developing country indebtedness, and (d) competition among projects in different countries. SOURCES OF DEVELOPING COUNTRY MINING CAPITAL1/ There is a wide range of financing mechanisms which are potentially available to developing countries with economically viable mining projects., Moreover, these financing mechanisms have not been fully exploited by developing countries, and more aggressive pursuit of financing by the governments of these countries may well reveal greater possibilities in respect of any particular project than may initially have appeared. However, virtually all the funds available from these sources are available only to projects which meet the standards of viability acceptable to lenders and others in the business community. If a project does not, for example, promise to generate a discounted cash flow rate of return of at least 15 per cent on total funds employed, or if it does not appear likely to generate sufficient cash flow in the early years of production to cover debt service requirements with a comfortable margin in reserve, most of the sources of financing will not be available. Only where a government has its own financial surplus (as in the case, for example, of the industrialization program of the Saudi Arabian government) can it effectively undertake projects which do not satisfy the definition of economic viability that is accepted at any given time by the worldwide financial community. Internal Sources In Developing Countries Internal financing capacity in developing countries is restricted to a relatively small number of countries - typically those large enough to support a well-rounded industrial sector, in which mining is only one of a number of dynamic industries. While there are large mining companies in certain other countries, the ability of such companies to finance new projects (or even, in some cases, to generate the cash necessary to maintain existing levels of production) is highly problematical. Within developing countries, the possible sources of internally-generated mining finance are the following: (1) state-owned enterprises; (2) private capital; (3) the banking system, and in particular those financing agencies that have a special involvement with the mining sector; and (4) direct budgetary appropriations.

Jan 1, 1985

By Donald R. East

The impacts of the economic storage or disposal of mill tailing wastes are becoming more important to the mining industry as environmental regulations become more demanding. Mill tailings have long been considered the stepchild of the extraction process and have not, until recent years, been treated as a separate entity of the mining and milling process with distinct and complex physical and chemical characteristics. As a waste product, the economic value of mill tailing is usually very small whilst economic and the environmental liabilities can significant. be Disposal of tailing is commonly identified as the single most important source of environmental impact for many mining projects.

Jan 1, 1990

By A. V. Tarasov

One or more of the main alloying metals, i.e. copper, silicon, nickel, magnesium, zinc and other metals can form a composition with aluminum, by dissolving in the latter. The thermodynamic computations have indicated that within a range of temperatures from 700°C to 1300°C the reactions of molten aluminum with zinc and nickel oxides are shifted toward formation of free metals because it is possible to use the main alloying metals, i.e. zinc and nickel, in the form of inexpensive intermediate products and waste. The laboratory studies conducted have confirmed a possibility for production of aluminum alloys using intermediate products in the form of oxides of alloying metals.

Jan 1, 2006

By Andrew Torok, Thomas D. Thompson

Research efforts have not developed techniques for the complete desulfurization of coal that is needed to reduce air pollution caused by burning coal and to reduce the sulfur in metallurgical coke. Sulfur in coal occurs in three forms and of these, the pyritic sulfur occurs as discrete mineral particles and, at least theoretically, should be subject to physical rejection. Pyrite occurring in hard rock mining is concentrated by froth flotation; therefore, the possibility of removal of pyrite from coal by flotation does exist. With this possibility in mind, the flotation and adsorption characteristics of ore and coal-pyrite were compared while using potassium ethyl xanthate as the collector.

Jan 1, 1973

By T. H. Dubaniewicz, J. E. Chilton

The U. S. Bureau of Mines is investigating the application of fiber optic technology to methane and carbon monoxide monitoring. A methane monitoring system is described that is based on differential absorption of infrared light. It can detect concentrations as low as 0.2% and as far away as 2 km via fiber optic cable. The upper range is 100% methane. The system requires no electrical power within the mine so it should operate safely under mine disaster conditions. A hybrid carbon monoxide monitoring system is described that combines a low-powered electrochemical cell with fiber optic telemetry. Testing has shown the system can operate maintenance- free for several months.

Jan 1, 1992

By Werner Burger

The last decade has witnessed a rapid development and application of slurry and EPB type tunnel boring machines. Both soft ground types are able to excavate tunnels in unstable ground conditions below the water table with positive face support. The most significant component of the excavation process is the cutterhead and tool con-figuration were the excavation and face support meets the geological challenge. The TBM downstream processes cannot take place unless the cutterhead and tools effectively do their job. This paper will review the current state of the art design for both slurry and EPB cutterheads and highlight both common as well as geological specific design features.

Jan 1, 2007

By S. Kelebek

Batch flotation tests were carried out using samples from stockpiles that were up to 1.5 months old as well as fresh samples oxidized in the lab for up to six months. Head grades and size distributions of samples were equalized whenever possible. The samples from stockpiles and oxidation experiments produced inferior nickel grade-recovery compared to the fresh sample. The poorer grade-recovery performance was attributable to two factors. First, a significant dilution effect was observed due to complete flotation of pyrrhotite. Secondly, the same stockpiling conditions caused nickel losses that were attributable to non-floatability of some pentlandite. Application of a high pH of 10 compared to the regular pH of 9.2 slowed down pyrrhotite flotation kinetics, but was not able to prevent complete flotation after 8 minutes. The samples oxidized in the lab did not match full characteristics of stockpile samples. They provided somewhat better selectivity for pentlandite. Some correlations were observed on a qualitative basis between surface characteristics such as elemental sulphur formation, activation and flotation behaviour. Oxidation conditions, which induce floatability on pyrrhotite while causing incremental loss in pentlandite floatability appear to be the root cause of difficulties in the processing of oxidized forms of these ores.

Jan 1, 2006

By B. P. Watson, A. Carpede, W. O. Kekana, N. Fernandes, W. Theron, M. P. Mahlangu, G. Betz

The research described in this paper was done to confirm the Upper Group 2 (UG2) PlatMine peak pillar strength formula (Watson et al., 2007), which was determined from a back-analysis of failed and unfailed pillars. Underground measurements were made on a stable pillar that was loaded by firstly reducing it’s length and then by mining the surrounding pillars until pillar failure took place. The pillar was instrumented with suitably positioned strain cells and closure meters, which allowed both the average pillar stress and strain to be determined. The paper describes the methodology applied to identify a suitable position for the instrumentation, as well as the results. A stress/strain curve is presented for a UG2 pillar with a w/h ratio of 2.0, at Booysendal Platinum Mine. The measured pillar strength was similar to the predicted strength using the PlatMine pillar strength formula for UG2 pillars. The PlatMine formula has been successfully implemented on Booysendal Platinum Mine, and about 3 670 pillars have been cut without a single failure. An additional revenue of US$1.3 billion was calculated for the 25-year life of the mine as a direct result of the improved pillar design, given the January 2020 platinum group metals basket price. An extended life of mine and better mining efficiencies will also be realized.

Aug 1, 2021

By Kawatra SK

The incentive to control coal flotation circuits arises because of disturbances, from plant operating practices and variations in feed coal characteristics, which result in large amounts of fine coal being lost in circuit tailings streams and lower grade concentrates being produced. Additionally, the flowrates and compositions of con-centrates and tailings streams can have significant effects on dewater-ing brocesses. A universal control strategy for these circuits cannot be developed. Rather, three major groups of variables must be con-sidered during strategy development: coal characteristics; circuit design and operating practice; and the variables selected to control the process. The second. and third groups-are discussed in this paper and examples from studies in operating plants are presented.

Jan 1, 1985

A report is given of the problems of finance and physical resources that currently affect The University of New South Wales, and of some of the measures adopted to alleviate them. Partly as' a result of review procedures, a School of Mines was formed to amalgamate Applied Geology and Mining Engineering, and to add the skills of extractive metallurgy to produce a group to match the needs of the minerals industry. A review of courses within the School indicated a need for enhanced computer teaching, which is partially negated by a lack of resources. It also shows an overcrowded course whose structure could possibly benefit from a split into managerial and specialist streams.

Jan 1, 1986

By R. Lai

This paper describes the application of a cyclonic flotation column (CFC) for coal cleaning. A CFC makes use of centrifugal force to create a density gradient in a column to augment the froth flotation process. In a CFC, a series of angular helical inserts is attached to the wall of a conventional column, and coal slurry is mixed with a series of impellers attached to a central shaft. The hydrophobic froth concentrates near the center shaft and moves upward, while the relatively heavy hydrophilic particles concentrate near the wall and are guided downward by the helical inserts. The results of pyritic sulfur removal from an Upper Freeport coal during CFC flotation are discussed.

Jan 1, 2003

By Kevork Chouzadjian, Gary Davis, Nicholas Katsikaros, Bruce Kelley, Mellie Mavatoi

A process has been developed to recover gold and copper from two waste materials at the Bougainville Copper Limited mine in Papua New Guinea. It involves the bioleaching, in reactors, of a pyrite concentrate to liberate refractory gold and generate sulphuric acid, ferric sulphate and biomass for bacterial leaching of a chalcopyritic waste rock dump. Gold is to be recovered by cyanide leaching and copper by solvent extraction/electrowinning. The reactor bioleaching was developed in continuously operated reactors of 1 m3 capacity by CRA Advanced Technical Development at Cockle Creek, while the dump leaching was developed in 750 kg columns on site at Bougainville Copper Limited. The process was to be piloted on site.

Jan 1, 1990

By Allan D. Fernie

Many long conveyors, 2 - 20 km plus, have been installed over the past 10 years. Conveyor belt life, depending on the conveyor length and material handled, will generally range from 10 - 15 years. To replace long conveyors splicing one or two rolls into a conveyor run on an intermittent basis can be prolonged in an operating system involving considerable downtime and scheduling problems. This paper presents some of the methods used to- date and highlights forward planning for such an event. Special belt handling equipment required and the execution of a belt change operation are described in detail. Wright Engineers Limited have worked in collaboration with Canada Conveyor to design and implement the methods described herein.

Jan 1, 1993

By W. R. Paterson, W. Morton, D. B. Cameron

The Massbal II computer simulation program has been used to develop a general framework for the building of thermochemical models of metallurgical processes. The framework allows the rapid, simple construction of complex models of process equipment for use in flowsheet design, planning and plant operation. Application of the program to model the iron-making blast furnace and a flash smelting process is described

Apr 1, 1991

By Guy Xueyi

The environmental impact assessment of the Imperial Smelting Process for metallic zinc and lead production in Shaoguan Smelter, China, was carried out by the life cycle assessment method. The detailed inventory analysis of the Input/Output in the process during 1998-2000 was conducted and the allocation was done among the main products of zinc, lead and sulfuric acid, according to the system expansion and substitution principle, The environmental impacts were assessed by using the following five Eco-indicators: Gross Energy Requirement (GER), Global Warming Potential (GWP), Acidification Potential (AP), Heavy Metal Toxicity' (HMT) and Solid Waste Burden (SWB). The results from this study are useful to address the environmental situation of the technology practice in this smelter, and provide a scientific basis for the further improvement.

Jan 1, 2003

By Guo Xueyi

The environmental impact assessment of the Imperial Smelting Process for metallic zinc and lead production in Shaoguan Smelter, China, was carried out by the life cycle assessment method. The detailed inventory analysis of the Input/Output in the process during 1998-2000 was conducted and the allocation was done among the main products of zinc, lead and sulfuric acid, according to the system expansion and substitution principle, The environmental impacts were assessed by using the following five Eco-indicators: Gross Energy Requirement (GER), Global Warming Potential (GWP), Acidification Potential (AP), Heavy Metal Toxicity (HMT) and Solid Waste Burden (SWB). The results from this study are useful to address the environmental situation of the technology practice in this smelter, and provide a scientific basis for the further improvement.

Jan 1, 2003

By Charles Will Wright

ITALY is by- far the poorest in mineral resources of the so-called great pou7ers of Europe. Before the World War this shortage was not so serious as the essential minerals that could not be mined domestically at a profit were bought in the world markets. In those days tourist trade and remittances from Italians abroad helped to provide Italy with foreign exchange. During the World War, when certain mineral products were scarce and when prices rose in some instances to several times normal, the Italian Government began to regulate consumption and imports. It was not until later, when the Fascist regime established the corporate state, that Italy seriously considered adopting a of self-sufficiency. Private industry was grouped under separate corporations, for the principal industries; including mining and metallurgy and the heads of the large producing companies, became members of these corporations. Industrialists were thus able to regulate their own affairs and to advise the Government as to the measures necessary to meet domestic or foreign trade demands upon their industry. Labor was or-

Jan 1, 1939

By W. R. Ingalls

IF, in this study of the outlook for the copper industry of the United states, I find myself assuming to be prophetic in some respects I shall express myself with hesitation and with the foresight that after the end of the war with Germany the war with Japan may continue; anyway there is sure to be an uneasy period before copper and the other metals begin to flow smoothly through the natural channels of consumption. It is mainly my purpose to survey conditions and suggest some probabilities, or possibilities, rather than to prophesy. In interpreting them it will be necessary to make certain aasurnptions, among which will be (1) expectation of a rise in the general price level,, which so far has been one-sided; (2) continuance of the k. tariff on copper imports; and (3) lock-up of government-owned copper as a military re- serve. Of these assumptions the first is indicated by the lessons from economic history, and by current symptoms. The second and third depend upon political action by Congress.

Jan 1, 1944

By F. Mielli

Ranging between 20% and 40% of the typical mining operational costs, energy in mining operations is a growing concern for the industry. However, this concern is a complex, multi-faceted variable that involves government regulations, societal pressures, cost and competitiveness. A mining company successful in energy efficiency is becoming the standard of a successful company. The suggested energy strategy in mining and mineral processing operations has to follow a well structured approach that entails the following: ? Understanding where energy is being used and why, ? Recommending and implement energy conservation measures, ? Driving visibility to targets and results, ? Leveraging the energy spend across the enterprise, ? Developing a robust energy and sustainability strategy.

Jan 1, 2012