Search Documents

By W. W. Roepke

The linear cutting system, developed by the U.S. Bureau of Mines, uses geometric principles developed by Cardan to produce a nearly constant cut depth. The new system has been extensively tested in a synthetic material under laboratory conditions to verify mechanical capability and to identify operational characteristics. Comparisons between 15-rpm linear cutting and 50-rpm rotary cutting systems show significant improvement in respirable dust entrainment, product size distribution, and energy usage. Respirable dust is reduced by as much as 90 pct. Recovered product showed a 67-pct reduction in -0.32-cm (-1/8-in) material and a 200-pct increase in +5.08 cm (+2 in) material. Average power was reduced by 66 pct for the linear cutting. Because the bit cutting paths differ between linear and rotary cutting, it was necessary to compare the two at the same cut depths and bit types. These comparisons show that low revolution per minute rotary cutting entrains about the same amount of respirable dust as the linear cutting system, but the average shaft torque may be 55 to 130 pct greater for the rotary system.

Jan 1, 2010

By Peter Middendorp, Gerald E. H. Verbeek

"This paper will describe a brief history of the method of characteristics as an accurate solution of the wave equation, and the author's experiences with the method of characteristics over a period of 30 years.As a result of the offshore pile driving activities associated with the development of the North Sea oil fields in the 1970's, two Dutch companies initiated extensive research efforts. Heerema started to research the dynamic behavior of soil during driving and HBG (Hollandsche Seton Groep) extended the method of characteristics with a straightforward theoretical solution for the shaft friction along a pile.The research institute TNO started the development of the wave equation program TNOWAVE in the late 1970's based on HBG's friction model extension for the method of characteristics. Today the program has a worldwide application in the field of pile testing. This paper will describe its development and application over time and its relation to today's applications for driveability studies for impact hammers (PDPWAVE) and vibratory hammers (VDPWAVE), signal matching for Dynamic Load Testing (DL TWAVE), Pile Integrity Testing signal matching (SITWAVE), and Statnamic simulation (STNWAVE).The paper will highlight that these developments have been the result of multi-disciplinary and multi-national efforts and encourage geotechnical engineers to seek further developments of the wave equation program in a similar manner. Finally, the paper will indicate some areas where such further developments are required."

Jan 1, 2005

There is no doubt that the mining sector is considered to be the backbone of many countries. Furthermore, it has played an important role in the prosperity of nations, whether developed or developing. Saudi Arabia is one of these countries that has a large variety of metallic and non-metallic mineral resources that range in size and value occurrences of limited potential to deposits large enough to sustain profitable exploitation. Therefore, the Saudi government needs to reinforce the capacity of the sectoral institutions to better regulate and promote the sustainable development of the sector. The ability to overcome the administrative and legal complications that constrain private sector participation in the minerals sector, through new mining code which will streamline the procedures for obtaining licenses and will add more predictability and transparency to the application process, are proposed for increasing the sustainable development. This paper will outline how the Saudi government is tackling the major challenges that face the minerals industry. This paper provides the background to the Saudi Arabian mineral sector and its industrial base. Finally, the paper identifies the problems and constraints that face the minerals sector in Saudi Arabia and provides an assessment of the effects of government policies and planning efforts in the minerals sector, particularly during the period of the development plans which started in 1970.

Jan 1, 2009

By Robert Torbin

The objectives of the Continuous Shaft Lining (CSL) System are to reduce the costs, safety hazards, and time currently required in lining mine shafts with concrete. The CSL will line machine bored shafts downward from the shaft collar on a continuous basis using an inverted, pressurized slipforming technique. The technique for slip-forming downwards has been demonstrated and refined under this program. The approach taken involved laboratory scale testing of key features of the CSL concept. These feature tests included concrete distribution, concrete sealing, concrete slipforming and development of a reliable concrete mix. Based on these results, a full scale above-ground test facility and CSL were designed and fabricated. The objectives of these tests were to demonstrate the viability of the basic concept; to establish operating limits; and to provide input data and information for the design of a second generation shaft lining system. The results of the program have led to a CSL design and operational philosophy which will need to be tested in an underground environment before industry will accept the technology. However, the next generation CSL promises to meet all the original program technical objectives.

Jan 1, 1983

By Ryan CG, Cousens DR, Sie SH, Suter GF

Proton microprobe analyses of trace elements have been carried out on a wide variety of ilmenites, garnets and chromites, to improve diamond exploration methods. The results so far show the potential to discriminate between barren and diamondiferous source rocks, and to distinguish multiple sources within single Drainages.

Jan 1, 1989

By James B. Fletcher

Leaching of the block caved mine from 1941 through 1970 is described, and the improvements made are listed. Detailed is the increased knowledge of leaching gained through this operation, including methods used in forecasting production, prediction of the economical end point, rate of recovery, and ultimate recovery.

Jan 1, 1972

By T Roberts

The transition of mechanical cooling refrigerants from their inception in the 1800s through to the current day has been driven by several factors. Original refrigerants such as sulfur and carbon dioxide, chloromethane and ammonia, whilst effective came with toxicity and/or flammability issues. In 1930 DuPont trademarked a new synthetic refrigerant known as Freon® 12, this development was the introduction of ‘chlorofluorocarbons’ (CFCs).Throughout the 1930s and 1940s additional synthetic refrigerants were developed, namely Freon® 11 and Freon® 22. Due to their non-toxic and non-flammable characteristics, synthetic refrigerants were extensively used for domestic, commercial and industrial applications for the next 60 years.In 1985, one of the first scientific papers suggested a potential mechanism linking CFCs and areduction in the density of the ozone layer. In 1987 the Montreal protocol is ratified; it is the first UN treaty to be ratified by every country on earth. Due to CFC’s ozone depletion potential (ODP), the treaty required the consumption of CFC’s to be reduced by 50 per cent over the next ten years. By 1996 the phase out of CFC’s (Freon® 12) is completed, the phase out of HCFC (Freon® 22) refrigerants comes into effect.On 1 January 2018 the phase down of HFC’s begins. Whilst having zero impact on the ozone layer HFC refrigerants have high global warming potential (GWP). As we transition through the HFC phase down (2018–2035) we are beginning to see the emergence of what some consider to be the fourth synthetic wave, hydrofluoro-olefins (HFO’s). HFO’s and their blends have zero ODP and low GWP’s, ranging from 150 to less than 1. The reduction in GWP with HFO’s typically comes at the expense of flammability, which is not ideal. Each refrigerant has its optimal application, therefor when considering refrigerant choices for mining systems, a complete assessment of the environmental, health and safety, efficiency and commercial impacts should be considered now more than ever.

Oct 12, 2022

This Bureau of Mines report summarizes the research, development, and evaluation demonstrations conducted by the Bureau of Mines under the Health and Safety Act of 1969 to improve the means of notifying miners underground, who are away from their own phone, that they are being called.

Jan 1, 1977

By L. S. Bicalho, W. J. Rodrigues, P. M. A. Rollo, P. R. G. Brandão, W. C. da Silva

Quadrilátero Ferrífero is an important mineral province located in Minas Gerais state, responsible for a substantial amount of iron production in Brazil. Among the concentration methods for iron ore practised by the mining companies in this region, the most important is the reverse cationic flotation. Dolomite iron formations, with the presence of hematite, quartz and dolomite, occur in several areas of mining and, with the deepening of the deposits, this type of ore, with low iron content and more complex mineralogy occurs frequently. Carbonaceous minerals, mainly dolomite, present a technological challenge for the concentration of iron ore by flotation. In the present study, the concentration of iron ore with 6% of dolomite content was evaluated. Bench flotation trials indicated that conventional iron ore flotation is not selective to float dolomite, thus compromising the iron content in the final concentrate. Alternative flotation routes were evaluated, and a selective condition was reached to float both quartz and dolomite using the combination of the cationic collector Flotigam 16424 with an anionic collector Flotinor 16551. It was demonstrated that the flotation of dolomite was improved with the combined use of both collectors in the cleaner stage, and by a previous quartz flotation in the rougher stage. Zeta potential analysis indicated specific adsorption as the adsorption mechanism between Flotinor 16551 and dolomite, confirming the high selectivity observed in the bench flotation tests. Keywords: Flotation, iron ore, dolomite

Jan 1, 2020

By I. Le May

"The assessment of integrity in plants is discussed, together with the codes that are being developed for in service evaluation of engineering fitness for service. The use of Risk Based Inspection is described and some examples are provided of the evaluation of in service components in which flaws have been detected. An example of the assessment of the structure of a mine processing facility is described, and application of Risk Based Inspection and plant assessment procedures to mines is discussed. Periodic assessment of large plants and components to determine their integrity for continued safe operation is becoming a more accepted approach than formerly when regular shutdowns were the normal practice. This is on the way to becoming the preferred procedure for petrochemical plants and power generating plants, and the same philosophy is appropriate for many mining operations. Both the American Petroleum Institute (API) and the American Society of Mechanical Engineers (ASME) have committees developing codes for the continued operation of equipment as distinct from the existing design codes. The philosophy is one of risk-based inspection, which can be on a purely qualitative basis or more quantitatively based.The purpose is to reduce the inspection of unnecessary and non-critical items and to concentrate on the most critical components, reducing costs and downtime and increasing safety. The approach differs from that considered by many maintenance engineers, in that defects that are identified during an integrity evaluation do not automatically cause a component or structure to be condemned or require that repairs are made right away. The seriousness of the defect must be considered and the safe operating life can be estimated before it becomes necessary to replace or repair the unit or component. This is no different from what is done today with passenger aircraft and, to an increasing extent, with pressure vessels, reactor vessels and similar components in the petrochemical and power generating industries."

Jan 1, 1998

By T Alexieva

Since the early 1900s the geotechnical community has investigated every significant failure of a tailings dam, improved our knowledge of the behaviour of the tailings storage facilities, developed analysis methods, compiled lessons learned, and committed to zero failures. The rate of occurrence of tailings dam failures has reduced since the 1980s, however, failures continue to occur and continue to surprise us. At BHP, we have decided to take an approach to the tailings management that is similar to the approach to safety. We are looking at ways to eliminate, substitute, separate or engineer around the hazard (tailings dam failure). As such, our ultimate long term goal would be to eliminate the need for new tailings facilities. Unfortunately, we have not developed yet technologies for extracting many of the common metals and minerals without producing tailings. Our shorter term goal is to substitute the current conventional slurry tailings facilities with less risky dryer facilities. We are working with vendors and research organizations to develop technologies that can be efficiently applied on a large scale. At the same time, we are committed to using the best available engineering to reduce the risks associated with our existing and new conventional tailings facilities. The best engineering can be achieved by people with the appropriate education, experience, attention to detail, discipline and authority. We have implemented a system of governance to make sure, we have the best engineering applied to all our facilities, considering the specific conditions at each site.This paper presents the current tailings governance process at BHP, and the initiatives that were undertook towards achieving a zero failure goal. CITATION:Alexieva, T, 2018. Tailings governance, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 2–7 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By T. A. Toney

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers, and recirculation have been attempted with some success. This paper reports on a novel (Patent Applied For) approach to retreating spiral middlings m a heavy-media-cyclone circuit.

Jan 1, 1998

By W. Blum

Progress made in improving the creep resistance of Mg alloys is reviewed with the emphasis on microstructural interpretation. Experimental results on the increase of creep strain with time at constant stress a measured for limited times and strains are displayed in a transparent form as creep rate-strain diagrams from which the minimum creep rate stress is safely derived. In addition, data on the thermal stress component a derived from high-precision a-reduction tests are reported. Within a simple statistical dislocation model these data allow one to quantify the relation between dislocation velocity v and a . In combination with structure evolution laws this relation serves as a basis for modeling the creep rate. New alloys have distinctly higher creep resistance than AZ91 where precipitation hardening plays a minor role. This is due to hardening by intermetallic phases which may form a continuous skeleton along the grain boundaries (e.g. Ca-alloyed AZ91) and/or submicron-sized precipitates within the grains (MRI230D, Mg-Zn-Ca alloys).

Jan 1, 2006

By T N. Little

This review paper presents an integrated and practical insight to blasting geology and its importance. This approach involves developing blasting objective up front and implementing geology specific blast designs. The author refers to this approach as ‘starting at both ends’. There are many human-imposed controls on blasting operations, such as: safety, security, legislative, company standards, heritage, and environmental constraints. Thus it is possible for some operators to lose sight of the controls imposed by nature. This paper demonstrates how site geology controls or influences many aspects of the rock breaking processes and how a focus on this aspect has potential to add considerable value to mining operations. It is obvious that mining companies concentrate their efforts on economic/ore geology (good rock geology). However it is the author’s experience that they also concentrate on engineering geology (bad rock geology) only when forced to do so by the ground conditions, but seem to run out of puff before they apply blasting geology (big rock geology). This paper contains five main sections. In the first section, the impact of geological controls on blasthole drilling is briefly discussed in terms of drill selection, penetration rates, bit wear, blasthole stability, blasthole deviation, and health precautions. In the second section the geological controls on aspects of geometric design are reviewed. These include: hazardous minerals, valuable minerals, selection of the blasting techniques, geological structures, blasting direction, and blasting geometry. Section three overlaps with the geometric design section and deals with aspects related to explosives. Topics addressed include selecting the explosive type based on geology, distribution of explosive charge in space and time, explosive performance, and the rock response to explosive loading. In the fourth section, examples are given of the operational complexity needed to implement a blast to cater for difficult bench geologies, environment constraints, past mining (voids) and need for a high degree of quality control. Section five demonstrates geological controls on blast results. Blasting results include the muck pile characteristics, downstream handling and processing, damage to the remaining rock, and blasting emissions.

Nov 8, 2011

By W. W. Agey

An inexpensive technique that laboratory studies indicated would significantly reduce seepage in irrigation canals was devised and tested through research sponsored by the Bureau of Reclamation and the Missouri River Basin Field Committee. Laboratory tests simulating optimum field conditions determined that easily applied sodium carbonate solutions made test beds of canal lining materials virtually impermeable for long periods. The study comprised alternative laboratory treatments of 3-inch-deep test beds of canal earths with 74 water-soluble chemicals in search of one 01' more that would effectively improve the water barrier characteristics of the component clays. Sodium carbonate, one of the least expensive, was among the most effective. The addition of 0,4 lb of reagent per sq yd greatly reduced the seepage from typical, highly permeable test beds. The reagent penetrated and sealed surface for about a 1.5-inch depth.

Jan 1, 1965

By D. A. Phillips

A procedure for designing an optimum pit to yield maximum profit is described. The volume in which a possible pit is considered is divided into discrete blocks, each of which is assigned an economic value equivalent to its worth as a block of mineable material. The profitability of a pit can then be generated by summing the blocks within the pit. The optimizing procedure starts at the surface level and proceeds downwards level by level, to obtain the optimum pit at each level. The method makes use of the fact that an optimum pit at a particular level must be completely contained in any optimum pit at a lower level. Procedures for generating block costs, and pits with various slope angles under the restriction of complete block removal are considered briefly. The main description is of the theory of the method and the computer program based on this. The method is applicable to any type of mineral deposit, the only requirement being that the orebody should be represented accurately by a block model.

Jan 1, 2014

By L. A. Cisternas, R. I. Jeldres, C. Cruz, P. A. Robles

"Previous studies have shown that the floatability of chalcopyrite in seawater at highly alkaline conditions is significantly affected by the presence of clays. The reason is that the species of calcium and magnesium present in seawater under those conditions may act as a bridge between the surfaces of clay and chalcopyrite, generating massive aggregates that then depress. In this context, the objective of this work is to analyze the impact of pretreated seawater with low amount of calcium and magnesium ions on the recovery of a sulphide copper mineral with high kaolinite content as clay. The seawater pre-treatment is done by the addition of sodium hydroxide in a high carbon dioxide environment. The chemical reactions realized under these conditions lead to the formation and precipitation of calcium and magnesium species that are subsequently removed by vacuum filtration. The pre-treated seawater is then used in flotation tests at pH 11 for copper sulphide, where the mineral is synthetically prepared by mixtures of chalcopyrite, kaolinite, and quartz. When comparing the flotation results for different types of water, including seawater and pre-treated seawater, a significant effect is observed: as the seawater hardness decreases, which comprises the calcium and magnesium ions, the recovery of chalcopyrite is increased. However, the effect is markedly enhanced in the presence of kaolinite. Therefore, the results indicate that sodium hydroxide and carbon dioxide are able to remove different species of calcium and magnesium from seawater and could improve the chalcopyrite recovery with high kaolinite content. INTRODUCTIONIn many cases, mineral deposits are found in arid areas with little access to water resources. Water is a fundamental element to carry out the unit operations that achieved the separation of valuable minerals (especially in concentration operations). Seawater has acquired an interesting role in recent years (Cisternas and Moreno, 2014); in fact, it seems to be one of the few viable options to ensure the sustainability of the mining industry in arid zones. At present, there are numerous experiences of industries that use or have used this resource, either by submitting the seawater to a desalination treatment by reverse osmosis or by applying it directly, without desalting. The latter case may involve significant economic benefits (for example, by avoiding the investment of building a desalination plant) and in some cases some operational benefits. A positive aspect is that in general terms the foaming in the saline medium is much more efficient compared to fresh water (Quinn et al., 2014; Castro et al., 2010). Some reports show that the foaming doses required to achieve a certain quality of bubbles are remarkably reduced, reaching exceptional cases such as Xstrata's Raglan concentrator, where it did not even include foaming to carry out the operation. This fact is quite promising, considering that some researchers have stated that controlling the quality of bubbles and foam could float minerals through coarse particles. This would lead to multiple benefits, such as energy savings by avoiding excessive grinding and a lower presence of fine ore that causes major problems in water recovery operations by gravitation (such as thickening) and in tailings management. However, seawater also causes significant challenges in multiple operations (Jeldres et al., 2017, 2016; Castro et al., 2010), as for example in minerals with high clay content (Uribe et al., 2017). In fresh water, the presence of clays minerals in ores is already a major problem in the flotation stages since the operation becomes difficult to be controlled, and operators are commonly forced to increase the consumption of reagents because the collectors are deposited on the clays' surfaces reducing froth stability (Farrokhpay and Bradshaw, 2012). Sometimes the use of rheology-modifying reagents should also be incorporated since the pulps become more visc"

Jan 1, 2018

By H Bateman, I Cawrse, G Carnes, S Cawrse

In developing mineral resources, the focus typically centres on the management of identified social and environmental impacts and compliance with regulatory requirements. However, opportunities to protect and enhance the environment and communities are most effective in the planning and design phases. Achieving the objective of integrating sustainability considerations as an element of design decision making requires that the design criteria be technically sound, relevant to the project and applicable to desired design outcomes. This is particularly important for projects employing virtual teaming, where design engineers may be geographically dispersed and are unlikely to be familiar with site specific sustainability challenges and opportunities. This paper documents the approach taken by BHP Billiton to incorporate sustainability principles, objectives and guidelines in design criteria for the Olympic Dam Expansion (ODX) project. It describes the range of inputs used in defining sustainability objectives which interface in a framework that is dynamic and transferable to other mining projects and to engineering design in general. The Sustainability in Design Criteria document distils statutory requirements, corporate standards, lessons learned and leading industry practice into a single coherent framework that supports engineers to approach problem solving as a holistic and integrated exercise with a long term perspective. The framework also serves to improve linkages between internal stakeholders by fostering greater communication, collaboration and innovation to deliver more sustainable outcomes through the design process.

Jan 1, 2009

By Jr. Gabler

Methods for the direct spectrochemical determination of impurities at the parts-per-million level in tungsten metal and oxide are presented. Several published procedures were investigated and numerous modifications were made in establishing procedures with improved precision and extended lower levels of determinability. Details of standards preparation are presented, experimental work is described, and three preferred methods are described in detail. A germanium carrier-distillation procedure is applicable to the determination of 13 elements in tungsten powder; a silver chloride carrier-distillation procedure provides for the determination of 24 elements in tungstic oxide, and a sustaining ac arc method is applicable to 26 elements in tungstic oxide. The choice of methods to be used depends upon sample form, elements and concentrations to be determined, and the precision and accuracy required. The investigations reported here were undertaken to develop direct spec-trochemical methods with increased accuracy and precision to determine impurities in high-purity tungsten and tungstic oxide, to define the lower concentration levels of detectability and measurement for the common impurities in tungsten by direct spectrographic means, and to present the details of the developed or modified methods that have proved applicable.

Jan 1, 1965

By Irving Wender

This report describes Bureau of Mines experiments and reviews the work of others on the exposure of coal and coal-derived products to gamma rays and some other types of radiation. Results are presented on tests of three bituminous coals and a lignite that had been pulverized to minus 200-mesh particles and exposed to 1,000 megaroentgens of gamma irradiation from spent-fuel elements of a nuclear reactor. Of about 20 chemical and physical tests in Bureau work, only mass spectrometry of gases evolved during vacuum pyrolysis of the coals to 450° C gave results indicating differences in the irradiated and unirradiated samples. Mass-spectral distribution curves for CO and CO2 evolution showed fewer irregularities (reversals of curvature) for irradiated coals; thus, mass spectrometry appears to be the most sensitive method for determining radio-induced changes in coal. It is concluded that coal is not significantly altered by gamma irradiation owing to the resistivity of its highly condensed ring structure. High-level gamma irradiation, therefore, is unlikely to prove advantageous in coal processing and utilization. Specially treated coals, because of resistivity of coal to radiation damage, may be useful as an absorbent in processing radioactive wastes.

Jan 1, 1968