Search Documents

By Andre Koekemoer, Gys Landman

At the moment, electronic initiation is migrating from a position of a specialist niche to that of a more widely applied technology. Ease of use and deployment rate are becoming aspects of greater concern for end users.

Jan 1, 2011

By Jian Li, J. Miles, P. Liu, W. Cook, W. Zheng, Alvin Qian

"High temperature corrosion resistance is one of the key challenges in water-cooled nuclear reactor material development. Iron based materials with low Cr content exhibits superior high temperature mechanical properties. However, due to the relatively low Cr content, their corrosion resistances under supercritical water (SCW) conditions are generally poor. High-Cr alloys, despite their much improved corrosion resistance, often suffer from embitterment due to the precipitation of sigma phase in the microstructure. In this study, corrosion resistance of an in-house produced high Cr steel (25%Cr) showed much better corrosion resistance compared to that of low Cr alloy (14%Cr). This high-Cr steel can potentially be used as a corrosion-resistant coating for structural materials in sew applications.INTRODUCTIONThe supercritical water-cooled reactor (SCWR) concept is one of the promising designs for the next generation nuclear reactor, in which the water coolant is designed to be at about 625°C and 25 MPa at the outlet of the reactor core. Under these relatively high-temperature and high-pressure conditions, the cooling water is at supercritical state. High-temperature mechanical properties, corrosion resistance and radiation damage are some of the key challenges. At present, no single commercial material can meet all the requirements of the severe SCWR in-core conditions. Canada supports research in several key areas of SCWR development, including materials selection. A major focus is on materials development, selection and evaluation for both in-core and out-of-core components.Allen et. al. [1] carried out a comprehensive study on the SCW corrosion resistance up to 600 °C on commercially available high temperature materials including Ni-based super alloys, various types of stainless steels and ferritic/matensitic steels. They concluded that ferritic steels develop a relatively thick but mechanically stable oxide layer, while austenitic alloys develop a thinner oxide layer that has been found to spall in some cases. Of the three types of alloys examined, the Ni-based alloys exhibited the lowest oxide thickness, however pitting was observed in the vicinity of intermetallic precipitates."

Jan 1, 2011

By W Patton, I Minniakhmetov, H Talebi, U Mueller

The sustainability of mining projects is linked to informed investment decisions based on public reporting of exploration and mineral resource estimation results. In Australia, public reporting guidelines are established by the Joint Ore Reserves Committee reporting code through the JORC Code (2012). Although the assessment of uncertainty in the results reported is a requirement, this is often communicated qualitatively and evaluated subjectively. This can become a liability particularly in the early stages of mining projects when spatial domains of geological interpretation and mineralisation envelopes inform resource estimations’ reliability. A recent review of JORC reports found no reports used quantitative assessments of the geological interpretation or mineral resource estimation envelopes, and 27 per cent of reports did not address the question of quality of geological interpretation. Reports that did address the quality used 19 different terms to communicate quality. This work presents methodologies for quantitative uncertainty assessment and communication and explores how they could be applied in public reporting practice. Quantitative uncertainty reporting would benefit mine planning and financial modelling as they normally assume the geology is 100 per cent right (since no error is reported or only a single deterministic model is provided). The complexity, cost, and additional work of doing a quantitative assessment could hinder a straightforward implementation. This could be overcome if mining companies budget for quantitative uncertainty assessment and associated professional development. A compulsory requirement for the inclusion of uncertainty assessments in public reporting or adopting standardised subjective language would improve industry practice.

Mar 22, 2022

Geological discontinues in the coalbed, such as faults, sandstone channels, permeability facies, lithotype changes, and large scale partings in the coal seam, can cause intermittent production problems or produce unexpected amounts of water or gas from degasification boreholes. These discontinuities not only can impact methane emissions into the mine workings, especially if they hinder proper and effective degasification of the coalbed but may act as conduits for methane flow from gassy strata into advancing mine workings. The effects of these discontinuities are still under debate by mining and gas production experts. This study presents a numerical investigation using reservoir simulations of the effects of partings and permeability facies and lithotype changes on the production performances of vertical and horizontal degasification boreholes, as well as the emissions during longwall operations. In this work, the grid block was designed in a multi-layer 3-D structure which enabled spatial descriptions of the geometries and properties of the discontinuities within the coal seam. The studied coal seam discontinuities and their properties were distributed arbitrarily within the model. Production was simulated by vertical and horizontal boreholes. Degasification boreholes operated two years prior to start of the mining. The results of this numerical study show that in coal seams with major heterogeneities and discontinuties, the geometry and location of the boreholes are important for improved gas production. These considerations are also important for controlling methane and water inflow into the working environment during longwall mining.

Jan 1, 2008

By Zhou Haizuo, Diao Yu, Zheng Gang

"The conventional design method for the embankment supported by DM columns usually assumes the simultaneous failure of all the columns. However, the progressive failure may occur in practice, especially considering that many researches have justified the critical load of DM columns is bending moment. In this study, a finite difference method was adopted to simulate the embankment on soft clay improved by DM columns. An increasing surcharge was applied on the embankment surface to investigate the mechanism of the progressive failure of columns beneath embankment. To capture the brittle bending failure of the DM columns, the model employed a cut-off method, in which the column was separated on failed section as long as the ultimate bending failure was reached. Furthermore, high-strength DM columns were used to enhance the global stability of embankment in this study. The numerical results showed that the ultimate bending failure was first reached at the column beneath embankment toe, and then a continuous collapse extended to the column beneath the embankment shoulder. It is found that the reinforcement could be obviously effective when the reinforced area of high-strength DM columns was extended to a certain area.INTRODUCTIONDeep mixed (DM) columns have been commonly used as a soil-improvement technique to increase stability and to reduce settlement of embankment. Research on failure modes of DM columns owing to embankment fill and surcharge has been the subject of interest for a number of investigators (Miyake 1991; Kitazume 2000; Han 2005; 2006).The potential failure modes of DM column include bending, inclination, shearing, rotating, soil flowing and a combination of these modes (Kitazume and Terashi 1991; Broms 1999). Many researchers have found that bending failure of DM columns was more critical than the shear failure. A centrifuge test was performed by Kitazume (2000) and the results showed that the columns failed in bending before shear failure. In addition, several numerical computations illustrated that design method using the shear strength overestimated the stability of embankment over DM columns (Han and Huang 2005; 2006; Navin 2006; Liu 2007; Wang 1996). In practice, an equivalent shear strength method based on bending failure could better reflect the stability of embankment (Zheng 2010; China Code JGJ79-2011)."

Jan 1, 2015

By T. W. Wlodek

"AbstractIn this paper a new type of durable 'spiral-rolled' drill set is introduced and its performance discussed. Efficient and economical mine drilling-depends to a great extent on durability of the drill-set employed. Premature failure of this element damages the drill bit and is costly when tungsten carbide bits are used.Time of drilling of 'spiral-rolled' drill sets introduced at present in Canada is considerably larger than for the presently used drill steel, but laboratory simulated service tests and practical field tests show that the 'drilling life' of the spiral-rolled drill set is several times that of ordinary drill steel.Some features of differential plastic deformation and differential surface rolling, so called 'spiral-rolling', are given.Relations between the drilling machine drill set and characteristics of the ore are discussed. The effect of shims on conical drill rod attachments, the mechanism of failure of drill steel, .and stresses during mine drilling, are analysed.IntroductionIN MINE DRILLING operations, the main interests are: the drilling machines as a source of working energy, the drill set as the tool transferring the working energy to the cutting edges of the bit, and, finally, the drilling characteristic of the .ore or waste rock.This paper includes a review of the possibilities of metallurgical and mechanical improvements in the drill set, with particular attention to drill steel and the attachments.For economical and efficient mine drilling operations, a durable drill rod, attachment, and drill bit are essential. Premature failure of any of these parts interferes with mining operations and is costly."

Jan 1, 1955

By Corby G. Anderson

Since 1985, the Sunshine Mining Company has used a patented nitric-sulfuric acid pressure leaching system for production of silver and copper from a refractory sulfide ore body. To better understand this novel process, a program of lab scale testing was undertaken to quantify the effect of system variables on silver recovery. Some of the factors studied include temperature, agitation, acidity, vessel pressure, particle size, percent solids and oxidizer amount. In turn, this knowledge will be applied in actual plant practice to upgrade reaction time, increase concentrate throughput, raise silver recovery and lower reagent costs. A discussion of plant process changes resulting from lab scale testing is included.

Jan 1, 1991

Commodities statistics and other information are available through the following three systems: Internet Access: To acccess the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, enviromental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

By K. Shame, H. H. Thiele

South Africa holds approximately 70% of the world’s total chrome reserves. Chromium is an important raw material for the production of stainless steel and ferrochrome alloys. Over the years, China’s ferrochrome market has been dependent on chrome ore imports from South Africa. In 2018, China imported about 75% of its chrome ore from South Africa. With the low platinum price and the rising demand for stainless steel, a growing demand to evaluate new beneficiation technologies for fine chromite was identified. Gravity separation of fine chromite (<75 μm) is inefficient, due to the limitations of the technology to upgrade fine particle size distributions. Potential for the recovery of chromite, specifically fines (<75μm), lost to UG2 PGM flotation tails, but also from MG and LG6 spiral circuit tailings exist. Flotation of podiform chromite ores from India and Kazhkhstan is successful in generating saleable product grade, following acid or alkaline flotation routes. Application to South African stratiform chromite is being evaluated, with the emphasis on evaluating reagent type, optimising dosages and the effect of pH in optimising flotation performance. Flotation can unlock additional value from chromite tailings material. The effect of ore characteristics such as gangue mineralogy, particle size distribution and headgrade are reported. The performance in terms of product quality and yield are evaluated and compared. The impact of this paper will not only prolong life of mine and increase revenue but will also alleviate environmental burdens associated with tailings dams. Keywords: Chromite, flotation, fine material, performance optimisation

Jan 1, 2020

By Henrique D. G. Turrer, Robert F. Winterfield, Jobe E. Wheeler, Marcello R. Cru, Baojie Zhang, Pedro P. Pinto

Efficient particle classification is essential to enhance gravity and magnetic separation stages in one iron ore beneficiation plant. This study investigates the use of high-frequency screens to process finely ground iron ore, focusing on two size cuts: 400 μm and 100 μm. Pilot-scale trials were performed on four ore blends using a full-scale screening unit. A total of 48 tests were conducted, evaluating the effects of panel aperture, solids concentration, wash water, and feed particle size distribution. Results showed that wash water improved efficiency by up to 5%, while a solids concentration near 40% w/w delivered high separation performance with minimal ultra-fines in oversize streams. Apertures slightly larger than the target cut sizes yielded better precision in particle separation. Feed particle size distribution had limited impact on efficiency. The investigation successfully identified optimal screening conditions, including aperture selection, to achieve the most effective separation performance for downstream concentration processes.

Feb 22, 2026

By D. A. Beattie

Three novel dextrin polymers of varying functional group chemistry but similar molecular weight have been used to depress talc in single and mixed mineral studies. The mixed mineral system was a model sulphide ore consisting of talc, pentlandite, and chalcopyrite. Adsorption isotherms for the three polymers on both valuable and gangue mineral phases were determined to give initial clues as to the ability of the polymers to depress talc. Flotation testing revealed a distinct hierarchy of effectiveness of the polymers in the depression of talc in the single mineral system (MP Dextrin > CM Dextrin > Dextrin TYM), reflecting the observed adsorption affinity and adsorbed amount of the polymers on talc. However, a different order of effectiveness was observed for talc depression in the mixed mineral system (CM Dextrin > MP Dextrin > Dextrin TYM). Competition between the valuable and gangue mineral phases for uptake of MP Dextrin is responsible for its observed decrease in efficiency in mixed mineral flotation. All three polymers were found to be reasonably selective in their action, although at high dosages the polymers began to affect the flotation of the valuable minerals.

Jan 1, 2006

By Jim Simpson, John Waller, Scott Stewart

The authors review the evolution of drilling and blasting procedures at this West Virginia surface coal mine where management seeks continually to improve and update the drilling and blasting programs. Today's operations require efficient programs which include quality control to maximize production and minimize the public's sensitivity to the blasting events.

Jan 1, 1992

By T. Imaizumi

Covering the whole scope of the MMIJ activities, i.e. geology and exploration, mining, mineral processing, and metallurgy, the technical innovations and improvements since 1972 were reviewed. Special references were made to the MMIJ Research Committees which were subsidized by the Japan Mining Promotive Foundation, in connection with those activities.

Jan 1, 1976

Data recently released indicate substantial improvement in mineral industry performance for 1984. Business plans to increase plant and equipment spending in 1984 by 14.8 percent, according to a recent survey conducted by the Commerce Department&apos;s Bureau of Economic Analysis (table 1). In contrast, capital spending by all industries declined 4.8 percent in 1983 and 2.3 percent in 1982. The latest estimate of planned expenditures for 1984 is $2.2 billion higher than the comparable estimate based on the survey conducted in late January and February 1984.1/ [ ] Of particular significance to the U.S. mineral industries are the 15.5-percent increase in capital spending planned by manufacturing in 1984 and the planned 18.6-percent increase in spending by durable goods manufacturing, where the largest increases are planned in the transportation equipment (26.4 percent) and electrical machinery sectors (23.5 percent). Capital expenditures in manufacturing declined in both 1982 and 1983.

Jan 1, 1984

With the ambitious target of adding another 2,00,000 MW of power generation by the year 2017 in India the demand for coal is bound to grow. The non-coking coal deposits in India are characterized as high ash and difficult-to-wash coals. Quality improvement by beneficiation is almost mandatory due to MoEF notification to use <34% ash coal for all power plants except those located at pithead. Most of the coal washeries in India are based on wet process, where the coal fines are allowed to settle in thickeners. The coarser particles settle faster leaving the fine particles suspended for longer period. The dispersed fine coal particles contain some surface charge, which leads to the development of electrical repulsion between the particles, and as a result of this, the suspension becomes more stable. In order to destabilize the colloidal suspension, flocculants are usually added, so that the settling rate of the fine particles also increases. These flocculants are of cationic, anionic and non-anionic depending upon the type of charge released when dispersed in water. The flocculants may act partly for charge neutralization and partly for inter particle bridging and electrostatic patch formation. The effectiveness of any type of flocculants depends upon the molecular weight and charge density of the polymer. The paper discusses the settling behavior of non-coking coal fines suspension by using different flocculants. Keywords: floculent, coal fines, sedimentation rate, effluent

Sep 1, 2012

An airlift pump is fitted to the screw conveyor of a decanter type centrifuge in order to pump out soft cakes which are difficult to discharge from a standard decanter. The new patented2 design improves separation performance and allows more stable operation, particularly when operating the decanter as a thickener.

Jan 1, 1989

By C Jincheng, L. Liang, L. Wenjun

"Considering overgrinding in a grinding process, the grinding characteristics of comminuted hematite products using a HPGR and a conventional CC were comparatively studied. The major properties including particle size, grinding kinetics and grinding technical efficiency (Et) were investigated. Individual size distributions (ISDs) of -2.0mm in a HPGR product showed a more significant “double-peak” characteristic than a CC product. As a result, HPGR products were finer and had a wider full-size distribution because of the greater proportion of fines. The parameters m and zi in m-th order grinding kinetics were analyzed by the partial-derivative method and the critical time tc(tc = exp (1/ zi)) was obtained. zi mainly affected the breakage rate when t < tc; otherwise, m mainly affected the breakage rate. In these tests, tc was considerably higher than the grinding times, and HPGR products yielded a higher zi-value than the CC product for the same sieve size. This indicated that HPGR products had a higher breakage rate and needed a shorter grinding time for a certain grinding fineness. Et was calculated by simulating the size distributions of batch grinding products. HPGR products gave a lower Et at a decreasing rate than the CC products for -2.0 mm feed and -0.5mm feed, and then showed a slightly higher Et for -2.0+0.5 mm feed. This indicated that overginding in HPGR full-size products was more serious under the condition of coarse grinding, whereas the efficiency was higher and overgrinding weakened significantly in HPGR coarse products because of screening-out fines. Based on the above research, a new process of “ultra-crushing in HPGR – classified grinding” was advanced, reducing ores tonnage into first stage ball mill significantly, improving grinding efficient and weakening overgrinding in the whole grinding process.INTRODUCTIONIn mineral processing, comminution accounts for a substantial portion (approximately 60~70%) of the energy consumed in plants. As an ultra-fine crushing equipment,the application of the HPGR for industrial comminution has been paid close attention because of its low specific energy, low steel consumption, high capacity and high ratio of reduction, among others (Schonert, 1998; Norgate & Weller, 1994; Fuerstenau & Kapur, 1995). HPGRs comprise two counter-rotating rolls that draw feed material into the roll gap. One roll is fixed to the mainframe, while the other movable roll is mounted on slides and positioned by hydraulic rams. The specific pressing force (SPF) (i.e., total force divided by projected roller area) is typically in the range of 3~9 N/mm2 depending on the application, while pressures of up to 1000 N/mm2 have been measured within the operating gap (Maxton , Morley, & Bearman , 2003)."

Jan 1, 2016

By Howard K. Worner

"In a rewarding career spanning nearly two thirds of a century, the author has worked at the frontier of such diverse fields as the creep of metals, structure properties and production of novel dental and surgical materials, molten salt electrolysis for titanium production, greatly improving the productivity of large iron blast furnaces and of oxygen steelmaking. While each of these has given great satisfaction, special thrills have derived from the development of new methods for the continuous production or refining of both ferrous and non ferrous metals. A rewarding segment was the evolution of various aspects of WORCRA technology. Unfortunately, several of these inventions have been ""ahead of their time"". Introduction""I am greatly honoured by the convening of this meeting to recognise my contributions to pyrometallurgy. My appreciation is the greater because this is the third Howard Worner Symposium; the first took place in the University of Newcastle in 1988, close to my 75th birthday. It was arranged by the local branch of The Australasian Institute of Mining and Metallurgy with the theme, ""Frontiers in Pyrometallurgy"". The second was organised by the University of Wollongong in conjunction with the Australian Academy of Science and the Australian Academy of Technological Sciences and Engineering; it celebrated my 80th birthday and, at my request, covered a broad range of topics under the heading of ""Recent Advances in Science and Technology"". Now, this very international meeting on ""Injection in Pyrometallurgy"" has been convened by the G K Williams Co-operative Research Centre for Extractive Metallurgy in my alma mater. I am both delighted and honoured that the cosponsors are the TMS (USA) and ISIJ (Japan).Dr Madhu Nilmani consulted me about the field to be covered and I readily concurred because ""injection"" has been of keen interest to me since the beginning of the 1960s when I began my pioneering work on sequential oxygen (or air) injection into flowing streams for both refining of blast furnace hot metal to steel and for the continuous smelting-converting of copper and nickel."

Jan 1, 1996

By Ashish Kumar, Khadija Said, Ulupi Mishra, Sekhar Bhattacharyya

Using battery-powered equipment in underground mining can improve safety, advance automation, and reduce greenhouse emissions. In this context, rechargeable lithium- ion batteries (LIBs) have a competitive edge due to their high Coulombic efficiency, superior energy density, and extended cycling stability. However, several conditions must be met for their safe operation. Their failure can cause thermal runaway (TR), which poses a significant safety risk in underground mines. Despite studies having investigated this phenomenon using physics-based models, limited research has used deep learning to predict its implications. This study aims to bridge this gap by characterizing LIB TR under dynamic airflow through simulations and predicting temperatures using two of the most common recurrent neural networks: long short-term memory (LSTM) and gated recurrent units (GRU).

Feb 22, 2026

By A. M. Poston

Introduction of radioactive elements into ore samples and/or pregnant liquors and radiometric tracing thereof have greatly improved control of fusion and extraction studies on beryllium ores and products. Extractive metallurgical research on beryllium, normally guided by the usual laborious analytical methods, is both costly and slow. Recognition of this problem by the Bureau of Mines led to the development and application of radioisotope tracer techniques" as a substitute for chemical analysis at the Salt Lake City Metallurgy Research Center, The result was that much faster progress at significantly lower cost was achieved. This report discusses the problems encountered and resolved in using radioactive tracers and radiometric methods, defines the conditions and techniques for their effective use, and delineates the limitations and flexibility inherent in applying such methods in laboratory-scale beryllium research.

Jan 1, 1962