Search Documents

Australia has a long and successful record in mineral processing technology extending over 100 years. This has included the development of new processes and equipment and new analytical techniques. These developments have added greatly to the efficiency of mineral processing and thereby to Australia's national wealth. Demands on mineral processing engineers in the future show no signs of diminishing, in fact they will increase considerably as more difficult areas must be treated and the requirements for quality control become more stringent. These demands must be met successfully since mineral processing must continue to be one of the most important technologies in Australia's economic future.

Jan 1, 1989

By E. V. Given

Designing a tailing dam is a major step toward fully integrated mill operation. In the case of large concentrators considerable planning is necessary, and the site of the tailing disposal area may very well dictate the location of the concentrator itself. Before a suitable location can be selected several pertinent factors should be investigated: estimated life expectancy of the mine and, if possible, approximate total tonnage; knowledge of daily mill capacity; and the possibility of future mill expansion. In addition, the area should be able to store tailing for many years and, from a cost and maintenance stand- point, gravity flow will probably be desired.

Jan 7, 1959

By R. G. Johnson

The prevailing system of locating wells on a rectangular basis, as shown in Fig. 1-A, has developed because of the exigencies of offsetting at boundary lines. When, however, a very large tract is being drilled, it is often possible to abandon this inferior method for the superior arrange- ment known as "staggering," which is illustrated in Fig. 1, B and C. The advantages of the triangular over the rectangular method are evident from Fig. 2, computed on the basis of one well to 10 acres (4 ha.). With the triangular system, no land is more than 409.4 ft. (124.8 m.) from a

Jan 1, 1920

By T. Lezhava

A new reactor model with rotating cathodes has been developed where various forms (dendrite, spongy) of metal depositions and their uninterrupted removal are accomplished by the realization of high current densities and low energy consumption. At the same time in contrast with the existing methods a high quality metal powder may be obtained from concentrated electrolytes without any specific organic or inorganic additives, which allows raising the intensity of the process. The reactor can be used for electrowinning of metals with low adhesive capacity (Pb, Ag, Cu, Zn, Ni, Co, etc.) and the powders. The obtained products may be utilized in general metallurgy as well as in powder metallurgy.

Jan 1, 2006

By Alan A. Campoli

Fosroc continues as a leader in the development of cementitious technology for the mining industry. The considerable expertise accumulated in the development of the Fm cement line has been employed in the development of two pumpable, supplemental roof support systems. The Tekprop system is a unique combination of steel and concrete, specifically designed as a viable alternative to conventional wooden supplementd support. The second system is the Fosroc mineable mi which is a cost competitive variable yield system designed to support longwall ventilation and predriven recovery room entries. Two, separate, ongoing, full scale applications of these systems will be discussed during the inference presentation

Jan 1, 1997

By P. Zhang

A multiyear, comprehensive study of flotation reagents used in phosphate beneficiation was conducted. The study involved the evaluation of pure fatty acid compounds, comparison of various anionic collectors and testing of iso-acids. Various C12 to C22 fatty acids were tested as Florida phosphate collectors. The saturated fatty acids were found to be very poor collectors when using the standard conditioning procedure, whereas the unsaturated C16 to C22 fatty acids showed fair to good phosphate collecting ability. The C18 fatty acids oleic, impure oleic and linoleic and the C20 eicosenoic acid were shown to be the best phosphate collectors. The best flotation results were obtained using Liqro GA tall oil and oleic acid. Four isostearic/iso oleic acid type fatty acid collectors were compared with a commercial grade oleic acid and with Liqro GA tall oil as phosphate collectors using standard laboratory conditioning and flotation procedures. The most selective collector evaluated was Century 1108, a high isostearic acid-type reagent. However, it was concluded that this excellent-performing reagent was too expensive for commercial use. Overall, the most promising reagent was probably Century MO-5. This collector is essentially an iso-oleic acid/stearic acid mixture (not isostearic acid), and it costs much less. This program laid a sound foundation for developing single collector, all anionic flotation processes.

Jan 1, 2009

"This model specification includes sample text shown in normal font with commentary in italics. The commentary is intended to highlight project-specific items the specification writer should consider during development of the specification. In some sections, typical values are presented to indicate common practice, and these values may be changed to reflect project-specific requirements. The commentary should be removed before using the specification for a project. 1. SCOPE The work consists of designing, furnishing, installing, and testing helical piles used to support foundation loads (compression, tension and lateral), and any ancillary materials (e.g., load transfer devices, etc.) according to the project plans provided and these specifications. Unless otherwise noted, the installing contractor shall provide all labor, tools, equipment and materials necessary to install the required piles. The parties referred to in this specification are as follows: • The Owner is the property owner. • The Owner’s representative is the individual or firm hired by the Owner to design and oversee the overall project. • The pile designer is the individual or firm generally hired by the installing contractor to design the helical piles. • Installing contractor installs and tests (if necessary) the helical piles, and possibly tasks associated with the project. It is important to clearly define the roles and responsibilities of every party on each project to promote good communication and reduce potential for contractual misunderstandings. Different types of contractual vehicles (design-build, value engineering, etc.) require different roles and responsibilities for the various parties, which should be considered in specification development. The Owner will provide suitable access to the construction site for the installing contractor’s personnel and equipment. Unless specifically noted otherwise in the contract documents, the Owner will remove and replace any structures, utilities, pavements, landscaping or other surficial improvements in the work area as necessary to facilitate the work. The Owner will be responsible for overall construction oversight to minimize potential for developing unsafe conditions. The work may include post-construction monitoring of pile performance if required by the Owner or the pile designer to confirm performance of the piles subsequent to their installation. The work may also include installation of additional piles if the initial installation does not meet specified capacity or performance requirements. Responsibility for providing subsurface investigation shall be addressed in the bid documents. The Owner is responsible for providing to the installing contractor all available subsurface soils, rock and groundwater information and geotechnical testing data."

Jan 1, 2015

By K. R. Johnson

Changes in the pattern of computer systems for mine planning and geologic evaluation are occurring as a consequence of the introduction of 3-D high performance graphics terminals. The VULCAN system is described and an outline of its functionality is discussed. Increasingly, the integration of both database systems and graphics and databases will occur, allowing a greater degree of information access to mine operators. The system covers areas of database, drillhole graphics, mine design and layout, surface and solid modelling as well as reserve inventory generation. The design of the software is such that it is fairly commodity-independent and entirely menu-driven, to enable non computer-trained personnel easily to access the system.

Jan 1, 1987

By Dennis V. D’Andrea, Larry R. Fletcher, Peter G. Chamberlain

The evaluation of potential in situ copper leaching deposits requires a thorough examination of the geologic, mineralogic, hydrologic and physiological characteristics of the ore body. The decision to develop the deposit is made with these data along with leaching properties, estimated copper recovery, and economic analysis. A test blast followed by pilot leaching can a so be used for further evaluation and to reduce uncertainty regarding the deposit's potential. This report describes a number of ground characterization techniques that can be used to evaluate potential deposits. Field methods include geologic mapping, groundwater hydrology, core drilling, geophysical logs, permeability testing, and in-situ stress measurements while laboratory tests include assaying, mineralogy, leaching, rock physical properties, size analysis, and computer simulation.

Jan 1, 1980

By D. J. McKee, D. M. Wiseman

The usefulness of simulation as a technique for metallurgical process design and optimization studies has been greatly extended over the last few years by the development of a number of general purpose simulation packages. The packages, or simulators, all have the common objective of presenting the mathematical models and simulation methods in a form which is readily usable by plant engineers and metallurgists. To date, most simulators have been concerned with steady state simulation, but packages capable of dynamic simulation are now becoming available. The paper outlines the essential features of versatile steady state and dynamic simulators. Typical applications are presented by considering examples of design and optimization studies. Limitation on the use of simulators are also presented.

Jan 1, 1991

By David A. Larson

The future exploitation of crust deposits will require a dependable characterization system. The U.S. Department of the Interior, Bureau of Mines (Bureau) initiated research to develop a new sampling dredge by conducting a series of cutting and physical property tests on previously collected cobalt-rich manganese crust and substrate samples. Using the engineering parameters derived from these tests, a large, heavy dredge was designed and tested. This heavy dredge was capable of fragmenting and collecting in situ crust, but it created handling problems for the research vessel, thus an aggressive cutting, light-weight dredge was conceived and fabricated. The light-weight dredge is capable of fragmenting and collecting crust and some talus. This dredge can be used on flat or rough seabed terrains. It can be easily retrieved from hang ups and reset to sample again.

Jan 1, 1991

ABSTRACT It is critical that historical processes and concomitant exposures to specific nickel substances be understood because some diseases linked to inhalation of certain nickel-containing substances have a long latency between first exposure and disease onset, and because nickel substances vary significantly in their toxicological properties. A discussion of the smelting history and related processes at Vale Canada’s (Inco’s) Copper Cliff, Ontario, smelter is integral to the understanding of these processes. The post-1950 processing history, equipment, propensity for aerosol formation, operational procedures, and ventilation controls used by Vale Canada in roasting, smelting, converting, and copper-nickel separation is discussed.

Jan 1, 2013

By A. E. Ketler

Conventional Atmospheric Monitoring System (AMS) installations for monitoring CO, CH4, O2 and air-velocity throughout underground mines are usually relegated to a modest 3-5 mile extent and with data communication speeds confined to a ponderous 1-5K baud range. New US-MSHA and state regulations require fast reporting of unsafe conditions, and the old 20-30 minute updates are no longer acceptable. To communicate farther and faster has always been a problem, because data reliability degenerates with excessive distances and high speeds. Because of this, very large mines often resort to costly optical-fiber media, using expensive OF cables and repeaters to obtain the necessary coverage. This entails high initial cost, as well as high maintenance and downtime costs to repair or replace broken optical fibers. Rel-Tek has pioneered with its DX-Bus communication data highway, which uses inexpensive twisted-pair telemetry cables, which can now communicate well into the 20-mile extent of the largest mines -- normally a brick wall for low-tech AMS systems. This extended range, enables the use of twisted-pair cables and provides a low cost alternative to OF systems. This paper discusses the DX-Bus, and its latest accomplishment, the ?B-LINK,? a unique high-speed communication repeater that maintains the 19.2K-Baud data rate. On-going innovations to our workhorse Millennia-DX computer software have kept pace with this extra speed/distance phenomenon, resulting in a dually-optimized AMS package: both hardware and software. Cost savings are substantial, and at no sacrifice of reliability ? nearly always at 100%. Sensor updates are measured in seconds, not minutes and hours. Twisted pair copper cable is cheap to purchase and install and a breeze to maintain. Rel-Tek uses the B-LINK's wide branching capabilities to enable the AMS to extend 20-miles both far and wide. Actual experience in large US coal mines -- both longwall and continuous mining operations -- confirms the large mine performance. The ventilation and safety benefits to the mining industry are immeasurable.

Jan 1, 2009

By J. Salazar

This paper presents a dynamic simulator of the semi-autogenous grinding operation deduced from first principles (non-stationary population balances) coupled to a Model-Based Real-Time Optimization (MBRTO) system to study optimizing strategies for an industrial semi-autogenous mill using genetic algorithms. For the design of the MBRTO both a validated first-principle steady-state model adapted on-line and a dynamic model were used to study the transient effect. The objective function considered is to maximize the ore throughput or the fine-product rate by changing the power-draw. For these purposes, these two performance indexes were introduced as fitness functions in the genetic algorithms. The three decision variables used were the ore feed rate, the water feed rate and the mill rotating velocity. The optimization problem was solved using a classical genetic algorithm with constant population. Constraints in the power draw and the filling level were handled by assigning a penalty function to the fitness function. Simulation results using industrial data for a large 1800 t/h copper-ore mill show the effectiveness of the system in finding the optimum controller set-points as a function of the process-operating constraints; mainly maximum ore feed rate, power draw and filling level. Starting from non- optimum conditions, the optimizer is able to improve the global performance index by 50% relative to a base case.

Jan 1, 2007

By J. C. Motz

The advantages of producing a fine mill feed have been recognized for many years. The extent to which fine crushing can be carried out will vary and depends on the ore characteristics, plant and crusher design. Unfortunately, the ore characteristics are generally beyond our control, so the concentration of effort lies primarily on the plant arrangement, equipment design and operation Where fine crushing should stop and grinding begin is controversial and is influenced greatly by personal opinions and experiences. Often, this break point will be different if consideration is being given to a new plant in comparison to a modest expansion. Most new plant designs employ the largest and most efficient equipment. The modification of existing plants becomes more complex because of the space requirements and the related equipment already in operation. Fine crushing is, of course, a relative term. Obtaining a final crusher product of minus 3/4" is commonplace today and can occasionally be obtained in an open circuit final crushing stage.

Jan 1, 1980

By D. G. Brubaker

IN the history of geophysical exploration by the electromagnetic method many procedures and types of equipment have been used. Source arrangements for surveying on the ground have included long wires grounded at both ends, large loops laid on the ground, small horizontal loops, and vertical loops of moderate to small sizes. Receivers have ranged from simple direction-finding coils to combinations of coils and a bridge circuit to measure quantities related to both amplitude and phase of the received signal. Primary considerations in choosing a survey method are effectiveness, speed, and economy. In work on the ground in which locating and outlining conducting bodies is the objective, methods using a vertical coil and a simple direction-finder have been found the most satisfactory. Mason1 and his associates applied such a method by setting up a vertical source loop, fed with low frequency alternating current by an engine-generator set. With a direction-finding receiver they surveyed lines along the ground in the plane of the loop, taking measurements at each station of the azimuth and inclination of the magnetic field direction. Deviations of this direction from the normal direction, that is, from horizontal and perpendicular to the traverse line, indicated a conducting body. Recent advances in design of light-weight generating equipment have encouraged using this and similar methods. In 1950 W. H. Westphal and the present writer developed a variation of this method and the apparatus for carrying it out. Their ideas were also based on experience with the Boliden Mining Co. method, which uses a small source coil and a vac- uum tube oscillator. The new procedure uses a small vertical source coil, powered by a vacuum tube oscillator, apd a direction-finding receiving coil. Source and receiver are kept a fixed distance apart and move as a unit along the survey lines. At each receiver station only the inclination of the magnetic field created by the source is measured. Source Unit: The source coil and a small vacuum tube oscillator together weigh about 45 lb. The source coil consists of about 60 turns of 10-gage

Jan 1, 1958

By T. V. Falkie, D. R. Mitchell

Many operational problems in mine haulage cannot be solved economically by conventional analytic or trial and error methods. However, a method of probabilistic simulation, which is based on the fundamental assumption that many of the variables governing any physical system are probabilistic, has been adapted to certain areas of operations research in coal mine haulage. This paper attempts to illustrate how simulation can be used in basic haulage research and what kind of results can be expected. Optimization in this case is performed in terms of locomotive and car movement, as well as best utilization of men and equipment, and is approached primarily from the standpoint of scheduling of the main haulage. Many operational problems in mine haulage cannot be solved economically by conventional analytic or trial-error methods. However, a method of probabilistic simulation, which is based on the fundamental assumption that many of the variables governing any physical system are probabilistic, has been adapted to certain areas of operations research in mine haulage. In many physical cases several probability distributions interact with each other in special ways, and it is not possible to solve for their combined effect in a mathematical equation. This is often true in the case of mine haulage, where such variables as number of empties or loads per trip, travel times, and number of cars or tons produced in a given time are probabilistic. By using a simple example of one secondary haulage segment of a large underground haulage system, this paper attempts to illustrate how simulation can be used in basic haulage research and what kind of results can be expected. Optimization in this case is performed in terms of locomotive and car movement, as well as best utilization of men and equipment. This is the type of preliminary research that will be needed as a first phase in any major haulage study, whether it be a relatively simple economic analysis or a plan for complete automation. The problem of optimization has been approached primarily from the standpoint of scheduling of the main haulage. It is evident that the method of proba-

Jan 1, 1963

By Robert E. Baker

Cortez Gold Mines, the United States' third largest primary producer of gold, commenced continuous operations on January 10, 1969. The decision to proceed to production was made in March of 1968 and construction of the mill and stripping operations for the pit began in April and July, respectively. Anomalous conditions on the slope of Mt. Tenabo along the Roberts Mountain thrust fault zone were discovered by the U.S.G.S. while conducting geochemical surveys in the old Cortez silver district. Following the discovery of gold an intensive program of drilling was organized. Drilling outlined an orebody with 3.5 million tons of ore averaging 0.28 ounces of gold per ton. It was on the basis of this reserve that a 1700 t. p.d. cyanide plant was designed. Needless to say, with such a limited ore reserve, economies in design and construction would have to be observed. Cortez Gold Mines is a joint venture with American Exploration & Mining Co., The Bunker Hill Company, Vernon F. Taylor, Jr., and Webb Resources, Inc. , as partners. American Exploration & Mining Co. is the operating partner.

Jan 1, 1969

In accordance with the usual custom, manuscripts to be presented at the next meeting of the Institute must be in the hands of the, Secretary before July 1, 1917. Manuscripts to be properly distributed in advance of the meeting must be in the hands of the Secretary before June 1, 1917. At the last meeting of the Institute 45 papers were presented, and 42 of them were actively discussed. This experience makes us believe that advance distribution is the best possible means of getting a good discussion of papers and of securing for them the interest of the members of the profession. It will be impossible, however, to give the papers proper distribution if they bare not received before June 1, 1917.

Jan 4, 1917

By Amanda Azman, Richard Hi Danie/son

Ultimately, the most important product of a hearing conservation program is the prevention of hearing loss, not the amount of hearing protection that has been purchased or whether employees are attending their annual training sessions. Audiometric testing directly reveals whether hearing losses are actually occurring in a plant. With audiometric data, we can assess overall program effectiveness, alert workers of impending hearing loss, and reveal potential employer liabilities for compensable hearing loss. Without the ability to efficiently analyze audiometric data or produce effective reports, our programs become fruitless and unproductive. Consequently, ifaudiometric data are such vital end-products, then effective audiometric technologies serve as the prime architect and generator of these fundamental data. These technologies, consisting ofaudiometers, associated peripheral hardware, and database/reporting software, deserve our consideration.