Search Documents

By T. N. McVay

The Bureau of Mines has developed a field test for detecting the presence of columbium in a variety of minerals containing the clement. The test consists of fusing the mineral or rock powder with potassium pyrosulfate in a porcelain crucible, digesting the melt with hot dilute hydrochloric acid to release the columbium oxide (Cb205), and subsequently reducing the columbium oxide to a lower oxide by adding tin, which gives a blue color to the contents of the crucible. The method will detect 1 percent of contained columbium oxide (Cb205) in a mineral sample provided no tungsten is present. If a mineral containing appreciable titanium is test,-!d in the same manner, the solution in the crucible becomes violet. In the presence of columbium, titanium at first causes a violet coloration of the solution, which after a few minutes is masked by the stronger blue of the reduced columbium oxide. Although tantalum oxide (Ta205) does not interfere with the columbium test, tungsten gives a blue color that is indistinguishable from the color obtained with columbium. A simple method is available to detect the presence of columbium in the absence of tungsten, but when the presence of tungsten is suspected, the sample must be subjected to somewhat more elaborate chemical tests to determine the presence or absence of columbium. Although these latter tests can be made in the field, several steps are involved that arc best performed in the laboratory with simple equipment.

Jan 1, 1962

By Warren L. J

In the mineral processing industry solid-liquid separation within a thickener usually requires the addition of a synthetic flocculant to enhance the settling rate of fine particles. The characteristics of the resulting flocculated suspensions may vary considerably depending upon the physical and chemical conditions which prevail during the flocculation process. For example, parameters such as flocculant type, dosage and solution concentration, surface chemical characteristics of particles and the suspension agitation conditions can influence the degree to which the particles aggregate. Aggregated suspensions exhibit various structures, and range from those composed of small, dense aggregates to those containing large, voluminous aggregates. The size distribution and structural type of the aggregates which form within the feed-well of a thickener can have a dramatic effect upon overall thickener performance. Thickener performance cannot be optimized without optimization of the aggregate structure produced in the feed by synthetic flocculant addition. This has required the development of new techniques to quantify the nature of aggregated suspensions, details of which are presented in this paper.

Jan 1, 1989

By A. Tobey Yu, W. Joseph Schlitt, Alfred Weiss, Frederic L. Kadey, Louis Kuchinic

Introduction The February and April 1984 issues of MINING ENGINEERING have already provided introduction to the long-range planning efforts of the Society of Mining Engineers (SME). These efforts are intended to provide the basis for effectively maintaining and improving the Society in the face of the changes that are besetting the mineral industry. This requires that SME recognize what changes are occurring and determine how these will impact the membership. Then a plan must be developed and implemented so that the Society successfully meets the challenges of the next decade. The Board of Directors has charged the Long Range Planning Commission with the responsibility for meeting these goals. This article provides a summary of the work done by the Management and Organization Committee of the Long-Range Planning Commission. This committee's task was to analyze the Society's current organizational structure and management process. Then a set of recommended improvements was to be developed. In doing this, the Committee has been careful to operate under that popular axiom, "If it ain't broke, don't fix it." Thus, changes were not proposed simply for the sake of change, but only where the present system appeared to be less effective than desired. Bases For Action The Committee began by establishing a set of premises about SME and its membership. These premises provided the bases for subsequent actions and recommendations by the Committee. Highlights from the premises included: • The Society should be run on a business-like basis. However, its "business" is that of a not-for-profit scientific, technical, and educational public institution. SME enables professionals involved in or associated with the mineral industry to serve the public purpose of benefitting mankind. • The Society operates as a national (US) organization with transnational (worldwide) interests. It recognizes its obligation to make its goods and services available to minerals professionals throughout the world. In addition, the Society recognizes its obligation to translate technology for the "lay" public, who then also become users of its goods and services. • The Society's Board of Directors is the policy-making body of SME and has final approval of all programs. These responsibilities will become greater when the Society becomes a separate corporation. • At present, the Society provides the following goods and services: publications, meetings/programming/short courses, academic education support, information dissemination - internal and external, and individual member services. • Planning is an ongoing process. It is best performed on a decentralized basis. That is, each major service category should have a responsible group authorized to conduct planning for that category, subject to the Society's master plan and the Board's approval. • The Society is privileged to have highly qualified and motivated members who volunteer their time and efforts on behalf of the Society. The best of these volunteers should rise to the highest positions of leadership - the Presidency of the Society and Institute (AIME). • The Sooiety is strongly committed to the protection and promotion of the history, traditions, and identity of AIME and the use of AIME as the unifying forum for the Constituent Societies. Identification of Potential Problems Once the premises about the Society and its membership were well in hand, the committee began examining the many facets of SME's organizational structure and management process. This was done in order to identify problems or potential problems in these areas. After considerable review and discussion, 10 areas of potential concern were called out for more detailed study and possible recommendations for improvement. These 10 areas include: • A lack of continuity at the Board level and among officers due to the established turnover policy. • A series of subboards that serve, by practice, to diffuse management authority and accountability, rather than enhance it. • A question as to whether the dissemination of information has been adequately planned, organized, and staffed. • An apparent illogical divisional organization. Two divisions are discipline oriented and two are commodity oriented. • A regional organization that does not adequately fulfill its purposes. • Uncertainties about the per-

Jan 6, 1984

By L Keeney

Cu-Au porphyry deposits are large tonnage low-grade resources dependent on processing large volumes of material. The ability to understand and predict comminution performance is critical, as it is frequently the rate-limiting step during processing. Parameters required from geometallurgical mapping and modelling of comminution performance are: A×b processing domains based on impact breakage variability, and BMWi processing domains showing grind response variability which lead to Mine throughput domains for a specific comminution circuit configuration. Due to the cost and/or large sample requirements of traditional comminution tests, insufficient data density and distribution of comminution indices commonly exist, making it difficult to model and map deposit scale variability. One method routinely applied to three dimensional domaining is to have an a priori zoning based on geological features (lithology, alteration, mineralogy, textures), and then apply to all material within a given domain the metallurgical values measured on a single sample or average of samples from that domain. The problem with this approach is that commonly the geological domains do not reflect comminution response, therefore compromising the quality of the average domain estimate. To resolve this problem an alternate integrated geometallurgical mapping and modelling method is applied to model and map comminution performance at Cadia East. This paper uses a data set of ~32 000 assay measurements and geological logging information, integrated with ~150 comminution measurements to analyse and develop proxy support models for comminution indices (ie A×b, BMWi, and throughput) based on inherent geological variability. Discrete downhole comminution processing domains are created, mapping orebody response while maintaining inherent variability.

Sep 5, 2011

By M. A. Trevits, G. Frampton

"Mine safety training materials have long included pictures of mine conditions, equipment, hazards, etc. These images are invaluable to both the trainee and the trainer to convey many important concepts. The human eye takes in a tremendous amount of information, while the field-of-view from a consumer grade camera is, generally, 40 degrees to 90-degrees. This difference in field-of-view is a primary reason that pictures, especially of dark and dusty areas, don’t adequately describe the scene. For conveying information to a trainee, these images lack context. Today, 360-degree cameras are available with consumer-grade cameras costing a few hundred dollars. Also, the display technology is already owned by most trainees and trainers and is widely available. The resulting 360-degree videos and pictures can be readily viewed on smart phones and inserted into Microsoft PowerPoint slideshows. These images and videos can easily be included in existing training modules, disseminated using the internet, and used by trainees easily. We propose a methodology for utilization of 360-degree video and images with simple display technology for miner training. INTRODUCTION AND BACKGROUND In mining, as in other production-related industries, the safety of workers is dependent upon many interrelated factors. One of the more important safety factors is a miner's ability to recognize hazards in their workplace. The ability to perceive and identify hazards is perhaps more difficult to master in underground mining than in general industry because the work environment is confined, noisy, dark, and inherently dangerous because of the hidden unknowns created by the geological setting and the conditions created by the mine opening. Further complicating the situation is a setting that is continuously changing as mining advances (Barrett 1995) [1]. Hours of excellent mine safety training have been developed and utilized over the years. Pictures of mines, activities, hazards, etc., are included in many of these training courses. These photographs, especially those taken underground, often lack context because of the limitations of the cameras and lenses. Notable research by the US Bureau of Mines and then later by NIOSH showed that the use of stereoscopic three-dimensional slides in training exercises was an effective aid for improving the ability of miners to recognize hazardous ground control conditions (Barrett 1988) [2]. An example of type of three-dimensional slides and slide viewer is shown in figure 1."

Jan 1, 2018

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, Matthew Gordy, Patrick Zhang

Waste phosphatic clay presents a difficult disposal problem and a significant loss of P2O5. Recent developments make this study on the use of phosphatic clay as a feed material for H3PO4 production worthwhile. (a) New data from Florida Industrial and Phosphate Research Institute (FIPR) suggest that the Bclay^ waste can be effectively treated by improved solid separation coupled with flotation to produce feed material for recovering additional phosphate. (b) The use of BOLI Flowsheet^ provides capability to predict performance of aqueous-based processes for a range of possible operating conditions. Using the new FIPR data and BOLI Flowsheet^ enabled the design of a new process that can potentially extend the usefulness of current P2O5 ore deposits. Predictions using OLI Flowsheet were able to identify process conditions that effectively overcome the difficulty of high Mg content of phosphatic clay. Estimated manufacturing cost in the current study lead to valuation of the P2O5 content of the phosphatic clay recovered/utilized at 60 to 70% of that of the phosphate rock feed material currently used. Phosphatic clay should be considered as a valuable material that is currently given zero value. The new FIPR data and BOLI Flowsheet^ enables the design of a new process that can potentially extend the usefulness of current phosphate ore deposits by extending the fraction P2O5 of recovered

By C Grobler, M Recklies, G Jiang, I Taylor, M Morgan, G MacDonald, L Smith

The resource estimation of lateritic deposits, such as Aurukun, presents specific issues related to the lateral changes in thickness and elevation of the various horizontal layers (or zones) within the deposit where the x and y dimensions are orders of magnitude greater than the z dimension. The objective was to develop a three-dimensional (3D) block model that retained the vertical and lateral variation inherent in deposits of this type to allow full optimisation of the production plan without prior selection of an economic portion (enriched bauxite layers) of the profile at the resource estimation stage. The Aurukun bauxite deposit is held by Chalco Australia Pty Ltd (Chalco) and forms part of the world-class Weipa bauxite province, Cape York Peninsula, Queensland, Australia. The bauxite is predominantly pisolitic with an upper boehmite-rich zone and lower gibbsite-rich zone. The bauxite consists of both in situ and reworked domains, is overlain by a thin soil horizon and has kaolinite clay as a transitional base. A portable infrared mineral analyser (PIMA) was utilised on site, in addition to elemental assay, on each drill sample to determine the mineralogy, in particular levels of boehmite, gibbsite, kaolinite and reactive silica. As part of the scope of work, a field program was undertaken using large diameter Boart Longyear sonic drilling to acquire detailed density measurements across the deposit to allow compliance with Joint Ore Reserves Committee (JORC) reporting requirements. Interpretation of the stratigraphy was conducted on a hole by hole basis with definition of the zone layering based on stratigraphy, geochemistry and mineralogy. The zone boundaries were then modelled as 3D surfaces and used to constrain a block model. The block model estimation used the ordinary kriging method, with the estimation done in unfolded space and then refolded, therefore maintaining the zones irrespective of thickness or orientation. The unfolding process converts the real-world positions for both blocks and informing samples to a scaled position relative to the roof and floor of each zone. Analysis of the data and variography were also undertaken in unfolded space. The x and y dimensions are unchanged, but the z dimension is a relative position. The effect of the unfolding and limits on number of samples per hole is to æpushÆ the informing sample search sideways but within the stratification, rather than vertically. This honours the strong vertical zonation within the bauxite profile. The JORC Code requires that the stated resource must have æreasonable prospects for economic extractionÆ. This is a qualitative rather than quantitative definition. A number of selection criteria to define a resource roof and floor were developed in consultation with the project engineers and owners to meet these criteria. The vertical selection of material to include in the resource highlights the variation in the development (and destruction) of the bauxite profile from area to area within the deposit.

Jan 1, 2009

By F. L. Meng, C. S. Henkel, R. M. Alchalabi

For secondary aluminum producers to maintain a profitable melting operation, five technical factors have to be taken into account from the initial furnace building decision to the final operation and production. These factors are furnace design, furnace equipment selection, furnace control, furnace charge selection and inventory, and furnace operation. Any of these five factors, if not chosen or performed wisely, will likely result in sub-optimal melting operation. As a result the MeltSim melting optimization package has been developed by the collaborative effort of Chinook Sciences and AMCS Corporation to take into account these five factors. The package is a mixture of hardware, software, science and experience. The package incorporates years of reverb furnace operational observations, start-up installations, furnace operator experience and furnace physiochemical mathematical model development. The optimization package enables aluminum producers to design new furnaces, select and place proper equipment, optimize existing furnace operations, and convert air-fuel installations to oxy-fuel. The package provides furnace operation monitoring and advisory signals, and furnace automatic optimal control to furnace operators, shift supervisors and plant managers, all customized, based on plant and melter need and ease of information management.

Jan 1, 2000

By Richard Lovat

INTRODUCTION Soft ground tunnels may be above the ground water table or they may be subaqueous. The ground may be clays, silts, sands, gravels, glacial deposits, boulder tills, and any of these in any combination. Because of the relatively low strength and deformability of soils, difficulties often arise in soft ground tunnelling. These soil characteristics and resultant tunnelling difficulties, have had a direct influence on the development of "Lovat" Tunnel Boring Machines. We have been required to recognize and adapt to unusual ground conditions and to follow through with design, fabrication, and field maintenance to ensure dependable, trouble-free operation. The basic "Lovat" machine is a fully shielded, wheel-type with the cuttinghead driven by a monorace type bearing with gear drive incorporated in the bearing. Mechanical innovations have been added to the basic machine which complement the resources of manpower, equipment, and materials available to the contractor for a specific operation. FULL FACE SUPPORT The installation of hydraulically operated closure doors or flood control doors, at the cuttinghead, is one of the early "Lovat" technical innovations. Flood control doors provide full face support in running or flowing ground. In water bearing sands and silts the excavated material can

Jan 1, 1981

By David J. Dunn

Materials related problems at mines can be big ones - like a newly completed 1 -m (3.5ft) water pipeline burst during initial filling, grinding ball consumption at double the typical norms on startup of a new semiautogenous grinding (SAG) mill circuit or 30 open-pit haul trucks in the shop for new bed liners after less than a year’s service. Materials engineering provides solutions to these kinds of equipment problems by selecting good materials and designs, by trouble-shooting service failures and by maintaining high quality in vendor-furnished materials and components. Materials with good properties, correctly made and fabricated, correctly installed in mining and processing equipment, produce ore and final products reliably and efficiently. Materials engineering, applied during design phases, specification writing, and receipt and installation of materials, ensures that equipment will have the best possible shot at performing up to expectations. Good calls on materials properties - specifying state-of-art materials produced by competent manufacturers - help mine managers to reduce downtime and mining and processing costs. Materials that are improperly made or specified can make a mining operation less efficient or, possibly, uneconomical.

Jan 1, 1992

By R. T. Stull, L. E. Geyer

"Previous Work:As outlined in previous papers* ond clays for graphite crucibles have been tested at the plants of the Detroit Lubricator Co., and the Detroit Copper and Brass Rolling Mills, Detroit, Mich.These tests indicated that there were two American clays (Missouri pot clay and Illinois kaolin) that tested better than the Klingenberg (German) clay. Dorset (English) ball clay was tenth in the list.Making the Crucibles:After it had been determined that American clays can be used successfully in graphite crucible manufacture and service, the next step in the investigation was to determine the value of American graphites as compared to the foreign, These final tests were carried out at the plant of the Detroit Lubricator Co., through the courtesy of Mr. G. B. Duffield. The crucibles, as previously. were made at the plant of the Vesuvius Crucible Co., Swissvale, Penna., from a formula compiled by the Bureau of Mines and under the supervision of Bureau engineers.The graphites to be tested were given an initial to indicate their source. The number of crucibles made and shipped are set forth in Table 1."

Nov 1, 1923

By Sarra Scherbakova, Alexander Kurkov, Andrey Egorov

"Deep concentration of iron ores involves extraction, in addition to magnetite concentrate, of hematite and martite concentrates and recovery of other valuable components. A flotation technology was designed specifically for finely disseminated hematite ore, allowing producing saleable hematite concentrate containing 64-66% Fe. The main process challenge is caused by the presence of other ferruginous minerals such as carbonates, silicates, and phosphates, and fine hematite and martite mostly concentrated in the -0.044 mm fraction. Main operations of the processing circuit are removal of slime, flotation to remove impurities (carbonates, phosphates etc.) with an anionic phosphorous collector in an alkaline environment, hematite and martite flotation using same collector in a slightly acidic environment to produce commercial iron concentrate. Tailings of wet magnetic separation of magnetite containing 24.5% Fe and finely disseminated hematite ore containing 51% Fe were processed to produce iron concentrates with a yield of 15% and 50%, respectively, containing approximately 65% Fe and 5% of silica. Hematite flotation tailings had the highest content of gold (up to 0.09 - 0.11 g/t), while in other products it never exceeded 0.02 g/t. Using a Knelson concentrator was able to recover 40 to 45% of the gold into 3.31 g/t Au gravity concentrate. The success of gravity concentration is due to high gravitational contrast of gold to mostly quartz and aluminosilicates in the hematite flotation tailings. In general, the proposed process can be used as a solution to the challenge of selective concentration of finely disseminated iron minerals."

Jan 1, 2014

By R. F. Favreau, Favreau Patrice

"The economy profits from the rock excavated in mines and quarries and the excavations required for the construction of roads and buildings. However such excavations are achieved by blasting withexplosives, and explosions create fly rock and vibrations which in some cases may throw rock far intoinhabited regions and may vibrate buildings excessively in these regions. Society, however, no longeraccepts that their quality of life be disturbed by the risks of fly rock or the perturbation of vibrations.Thus it is important to know how to design blasts that do not cause excessive fly rock or vibrations, and to understand why sometimes a blast does create excessive vibration or fly rock. An article presented at the 2015 ISEE (reference 1) explains how unacceptable vibrations can be avoided, while the present article explains why dangerous fly rock occurs and how it can be avoided. The article shows by rigorous calculations with the blast simulator Blaspa that long range fly rock can be due to short collar or short burden, but mainly it explains how inadequate blasting that allows the floor to rise can cause even further reaching fly rock, a situation not usually recognized by most blasters."

Jan 1, 2016

By Murray W. Hitzman

Two great revolutions in mining occurred during the 20th century. The first took place almost 100 years ago (1903-1905) with Daniel Jackling’s experiment in the economies of scale for large-scale mining at Bingham Canyon. Jackling’s ideas changed the focus of base metal exploration toward lower-grade, high-tonnage deposits. The second revolution was the impact of environmental and social concerns on mining. It started near the end of the 20th century and is still under way. This article speculates on the effects of this second revolution on the future of mineral exploration.

Jan 1, 2005

By W. A. Vine

When a hole is made in a stressed solid, such as rock pierced by mine openings, equilibrium of the solid is destroyed. To restablish that equilibrium the stress condition in the rock surrounding the opening becomes rearranged. This rearrangement may or may not develop local stresses in the vicinity of the opening which exceed the elastic strength of the rock. Since stability of the opening depends, therefore, on the strength of the naturally occurring rock surrounding the opening, this rock is an engineering material of construction, and all rock affected by the associated opening or system of openings may be considered a structure. The term invert is chosen to describe the formation of the structure built from the inside, as it were, and a consequence of mining rather than an entity built for a purpose. By definition, an invert structure is formed when openings are made underground and is com- posed of that material on the solid side of a rock-air interface wherein the stress condition is affected by the associated opening or system of openings. The shape of an invert structure is never clearly defined; the skin of the structure may be mapped, and even described, but the boundary of the structure within the solid rock mass must be arbitrarily set.

Nov 1, 1955

By Edward Martinez

The literature on the beneficiation of serpentine asbestos ore states that the specific gravity of the rock containing fiber and the fiber itself is the same so that specific gravity cannot be used as a basis for separation. An investigation of particles of asbestos ore ranging in size from 4 mesh to 5 in. revealed that the fiber-bearing particles generally had a lower specific gravity compared to essentially barren particles. The difference in specific gravity was sufficient to make an effective gravity separation of ore particles and reject a low grade tailings product. The results of laboratory tests are described that lead to the running of pilot plant tests with 20-ton ore samples using a heavy media separator. These tests indicated that a large amount of low grade material could be rejected from the raw ore at a coarse size. Although the process used is a wet separation, it can be added to a conventional dry asbestos mill. A gravity preconcentration would allow the mining of lower grade ore, increase the life of the mine, increase the value of the feed to the fiber recovery section, and decrease maintenance costs by removal of low grade tailings early in the flowsheet.

Jan 1, 1975

By A G. Mitchell

Stream sediment geochemical analyses were collated from open-file mining company reports and assembled in the REGCHEM computerised database at the Institute of Geological and Nuclear Sciences Limited. The database operates on an IBM-compatible PC microcomputer using an application programmed in dBASE IV and termed GEOEXPL. By August 1992, data for 6383 stream sediment samples from 6335 different sites in the Coromandel Peninsula region (Hauraki Goldfield) were entered, giving a total of 29 292 separate elemental analyses. Preliminary statistical analysis using PROBPLOT on a set of data collected by AMOCO from the Mahakirau-Whangapoua area shows that these data are a complex mix of subpopulations related to mineralisation and different source rock types. Thresholds of 37 ppm copper, 31 ppm lead, 112 ppm zinc, and 2.3 ppm molybdenum, defmed by arithmetic models for the combined data set, separate the individual element sets into 'first order anomalous/lesser anomalous and background' subpopulations as follows: copper five per cent/95 per cent, lead five per cent/95 per cent, zinc one per cent/99 per cent, and molybdenum 15 per cent/85 per cent.

Jan 1, 1992

By J. Scott McDougall, J. Herman P. Eng. Vanderlaag

An underground mine fire can seriously threaten the lives of all personnel in the mine. This fact makes fire emergency planning a high priority in the mining industry. The optimum warning alarm must be fast and able to reach all miners, regardless of their location or work activity. Current means of fire warning are varied, and include such methods as stench, telephones, and word-of-mouth (messengers). Unfortunately, none of these methods are entirely satisfactory. A novel fire warning alarm which enables instantaneous warning of all underground personnel, the Canary Nine Messenger System, has been developed by VLF Magnetic Systems Inc. in conjunction with Noranda Technology Centre and the U.S. Department of the Interior - Bureau of Nines. The warning is sent by an electromagnetic signal which penetrates through mine rock to receivers housed in the battery packs which also power each miner's cap lamp. A loud buzzer in the integrated battery/receiver unit and the flashing of the cap lamp alerts miners to incoming messages. Testing of prototype equipment has demonstrated that the transmitted signal is capable of penetrating through over a mile of mine rock and activating the receiver. This report describes the theoretical basis for through-the-rock ultra-low frequency electromagnetic transmission, and the design of recently available transmitter and receivers.

Jan 1, 1995

By Sabert Oglesby, Albert L. Thomas

Until recently, probably the best means of sampling airborne dusts has been the impinger method. Dust-laden air is drawn into a sampling tube, and the particulate matters separated from the air and collected in the liquid in the impinger. A sample of the suspension is prepared on a slide and counted through a projection microscope. This method is simple and reliable, but it does suffer drawbacks. Since the collected particles must be counted visually, results of the dust count are taken. This seriously impedes studying the effectiveness of dust inhibitors, such as water sprays, or making adjustments in equipment. Greatest disadvantage of all, however, is the tedious task of counting particles in the sample. With the growing desirability of taking more samples, the effort involved in making these counts is a real factor in the cost of dust control. Finally, it is generally recognized that impinger dust counts can be related to health hazard only for specific kinds of dust and under similar conditions. This is because the rather complex mechanism of dust damage depends so much on size distribution of the dust. Counts determined by impinger samples cover a limited size range that does not necessarily correlate with retention by the lungs and upper respiratory tract.

Jan 3, 1959

By C. E. Webber

THE economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro-carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,5 who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40° to 200°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33° to 180°F. and from 100 to 5000 lb. per sq. inch.

Jan 1, 1940