Search Documents

By S. Z. Khan, Veerendra Singh, Y. Rama Murthy, S. Prasad, Sunil Kumar Tripathy, Gajanan Kapure

"In this study, a low-grade ferruginous low-grade chromite ore was subjected to reduction roasting by using conventional heating as well as microwave heating. Sukinda chromite ore deposit contains majorly iron-bearing minerals as gangue phase. The magnetic susceptibility of these minerals enhances effectively after reduction roasting. Alteration of crystalline structure and magnetic property of these metals enables separation of low-grade ore by using magnetic separation. Conventional roasting studies by varying the temperature, time of reduction and reductant dosage were changed for low-grade ferruginous chromite ore. Similarly, microwave power, retention/exposure time and reductant dosage varied for reduction roasting studies under microwave environment. It is found that low-grade ferruginous chromite ore can be upgraded by reduction roasting and 61.2% Cr2O3 was recovered with a chromium-to-iron ratio of 1.93 from feed chromium-to-iron ratio of 1. Microwave reduction roasting studies resulted in upgradation of chromium-to-iron ratio to 1.73 with a recovery of 21% Cr2O3.INTRODUCTION The chromite ore occurs as a spinel containing oxides of chromium, iron, magnesium and aluminium. Most of the Indian chromite deposits are of ferruginous (rich in iron content) which indicates the abundance of ferruginous gangue minerals along with chromite. The primary use of chromite ore is towards the production of ferrochrome alloys. Chromite ores with less than 40% Cr2O3 and the chromium-to-iron ratio (Cr-to-Fe ratio) <1.8 is considered to be unsuitable for the smelting process (Tripathy et al. 2012, Tripathy et al. 2012a). A considerable amount of low-grade chromite ore and overburden excavated during chromite mining is getting accumulated every year, causing a threat to the environment. Its disposal poses a significant challenge and, hence, the beneficiation of low-grade chromite ore and its utilisation has been attracting a lot of attention. Different physical method of beneficiation methods is generally employed for the improvement of the Cr-to-Fe ratio (Tripathy et al. 2012, Murthy et al. 2011, Tripathy et al. 2012a, Tripathy et al. 2013, Tripathy et al. 2016, Tripathy et al. 2017, Tripathy et al. 2017a). It is observed that the enrichment of the chromite ore is carried out by using gravity and in some places by magnetic separation. However, the enrichment of Cr-to-Fe ratio from low-grade ferruginous chromite ore is difficult by using the above-mentioned beneficiation methods due to the presence of near gravity and near-magnetic susceptibility minerals along with chromite. However, an alternative beneficiation method is needed to explore for the beneficiation of such mineral deposits. Reduction roasting followed by magnetic separation is an alternative option for the separation of these types of ores which is widely reported for the iron and manganese ore (Li, et al., 2010; Chun, et al., 2014, Rath et al., 2018). These processes are majorly focussed on differentiating the magnetic susceptibility between minerals and subsequent separation by using magnetic field. The main advantage of such method is dry process option along with the pre-processed product for the costly smelting process. Also, the roasting of minerals in a microwave environment is also an active research topic in the recent time. So, the amenability of the separation feature of the roasting process by using conventional heating as well as microwave heating can be can be studied for the low grade ferruginous chromite ores."

Jan 1, 2018

By Elisa Alonso

Manufacturing firms that rely on finite resources have a stake in ensuring sustainable materials use. Higher material prices and uncertain material supply, consequences associated with scarcity, can be damaging to firms. Firms have a number of options to improve material sustainability including dematerialization, material substitution and recycling. However, these options require technological capability, capital investments and supply-chain infrastructure; firms may decide to make such investments only if material prices increase. Once decisions are made, the barriers and delays to implementing changes may harm firms. The impact of not reacting to changes in material supply on firms was examined for the case of different platinum-using industries. It was found that taking action is particularly important for firms when limited material availability leads to volatile market conditions. Industries can benefit especially if they ensure process flexibility and have options for changing their material use patterns.

Jan 1, 2010

By C. Liu, G. Zhu, Y. Liao

"The effect of particle size on the flotation kinetics of a low-rank coal was compared using air bubbles and oily bubbles. Five kinetic models were applied to the data from the tests to derive the relationships between the flotation rate constant, the ultimate recovery, and the particle size fraction. The results show that oily bubble flotation (OBF) resulted in a lower ash content and higher combustible recovery than air bubble flotation (ABF), especially for the -125 ??m size fraction. It was found that the flotation of a low-rank coal in individual size fractions using air bubbles and oily bubbles can be best described by a first-order model with rectangular distribution of tendency to float and the classical first-order model respectively. OBF yielded higher ultimate combustible and ultimate ash recoveries. The flotation rate constants for OBF were higher in all the models except for the fully mixed reactor model. The ultimate recovery values and modified rate constants first increased and then decreased as the size fraction decreased. The trend of the flotation rate constants as a function of the size fraction was similar in all the models except for the fully mixed reactor model. IntroductionFroth flotation is a physical-chemical separation method that is widely used in coal beneficiation for the separation of fine coal particles from associated minerals in water slurries. Since the cumulative recovery of a component in the concentrate is proportional to flotation time, the flotation process can be considered as a time-rate recovery process (Emad, Mohammad, and Bahram, 2010). Therefore, the general mathematical flotation models that incorporate both a recovery and a rate function can describe flotation time recovery profiles.The kinetics of coal flotation, as a measure of coal recovery as a function of time, have been studied in detail by many researchers. Different kinetic models have been proposed and published in the literature. The order and the rate constant are strongly dependent on the flotation conditions, such as the particle size and size distribution, the bubble concentration, the reagent concentrations, and the operating parameters (Zhang et al., 2013). The particle size has been reported to affect the flotation kinetics to a great extent (Yoon, Luttrell, and Asmatulu, 2002; Ntengwe and Witika, 2011). Numerous researchers have studied the aspects of flotation kinetics while paying special attention to particle size (Meftuni and Ibrahim, 1997; Rubinstein and Samygin, 1998; Graeme, 2012). However, the effect of particle size on the flotation kinetics of a low-rank coal has been relatively little discussed."

Jan 1, 2017

By R. N. Johnson

This report is a summary of the work performed for the Bureau of Mines to evaluate the feasibility and desirability of a movable in-pit crusher combined with conveyors to substantially reduce or eliminate truck or train haulage in large open-pit non-fuel mineral mines. The report includes an introduction and summary of previous work, an analysis of movable crusher system components, a description of the selected system, a review of possible movable crusher system applications, and finally requirements for future work to bring about the general availability of such systems. It was clear from the program that there is a real need for movable in-pit crushers.

Jan 1, 1982

By Mikael Ramström

In 2002 Atlas Copco Rock Drills AB released the new RCS technology for all of its drill rig types. RCS opened the way for a new generation of computerized drill rigs based on modern, standard PC-computer technology. Drilling accuracy, information logging and reduction in manpower in some types and serviceability, have all taken a quantum leap forward when compared with previous generations of drill rigs. The RCS (Rig Control System) is modularised and distributed is accomplished by means of CAN-bus technology. This technology, which is well proven in automobile applications, forms the communication backbone of the rig. The modularity facilitates almost unlimited possibilities for the expansion and adaptation of drill rig functions.

May 1, 2003

By Robert L. Russell

The Bunker Hill Mine, located in the Coeur d&apos;Alene Mining District at Kellogg, Idaho, has been a major producer of lead-silver-zinc ores since its discovery in 1887. The mine has produced over 29 million tons of ore from some 20 to 25 veins and ore zones, and now covers an area approximately one mile in length and one-half mile in width. The active section of the mine extends from 2500 ft above sea level to 1600 ft below sea level. Production is presently at the rate of about 1700 tons of ore per day. A two-mile adit, the Kellogg Tunnel, at the 2500 elevation, provides access to the main shaft area. Ore is hoisted to the adit level through a 5000-ft, 500-inclined shaft, extending to the lowermost haulage level 1200 ft below sea level. Primary shaft service for men and materials is supplied by three major internal, inclined shafts equipped with double-drum hoists. Present production requires ten levels to serve for mainline track haulage. These range up to 5000 ft in length and are either 200 or 400 vertical feet apart. Also, many intermediate levels exist throughout the mine. The conventional and autoloader mechanized square-set and cut-and-fill mining methods used throughout the mine have been the subject of a recent paper(l). One-third of current production is from vein-type ore bodies which are long distances from main shaft areas. Such veins generally dip about 450, have relatively narrow widths of from 3 to 20 ft, and usually contain less than 500,000 tons of ore. For many years, ore bodies thus situated have been developed by means of a separate inclined, timbered service shaft-raise connecting two or more main haulage levels. These commonly range from 400 to 1000 ft in vertical extent and are equipped with 25 to 50 hp electric, single-drum hoists. Intermediate levels are driven as conventional track drifts at 100-ft vertical intervals between the haulage levels. Ore and waste from the intermediate levels are trammed to orepasses for delivery to the lowermost haulage level servicing an ore body. The final result may be visualized as a number of small mines within a large mine. The problems of high development costs and high total development time, and the large amount and high cost of providing materials handl ing and ore haulage service while producing from this isolated type of stope block, made it desirable to consider totally new approaches in developing and mining a number of similar areas.

Jan 1, 1971

By Edwin B. Wilson, Charles F. Cockrell

The application of evolutionary operation is proposed for the cleaning of coal by the heavy media process. Analysis of the data given suggests some benefits that may not be immediately appreciated unless evolutionary operation is applied. For example, while it may seem obvious to increase specific gravity when the ash and sulfur content of the clean coal is lower than that allowed, evolutionary operation may show that an increase in feed rate or an increase in both feed rate and specific gravity would be a more profitable alternative. In addition, by using evolutionary operation, up-to-date knowledge of the effect of change of feed rate or specific gravity on yield and product quality is available. This information facilitates confidence about decisions made in regard to the day-to-day operation of these units. A number of other applications in the minerals industry are proposed. An application of evolutionary operation in a related field is also given where a large number of variables were required to be optimized.

Jan 1, 1969

By Carl G. Bock

INTRODUCTION The Washington Metropolitan Area Transit Authority (WMATA) has let a contract for the excavation of three rock stations, spaced about 3550&apos; (1082m) apart, beneath Connecticut Avenue in Washington, D.C. Two previous rock stations have been completed, one of which had a crown pilot tunnel excavated to explore geologic conditions that would be encountered during the station excavation. This pilot tunnel was primarily for inspection by bidders and design was based on core hole information. The other rock station had no pilot tunnel and was also designed on the basis of core hole information. The three rock station areas, which are the subject of this paper, have been explored by crown pilot tunnels and an as-built report, with geologic maps and sections, has been prepared, for use by the design engineer as the basis of design for support of the structures. The geotechnical report describes the geologic structure in detail and relates it to excavation and support of the three crown pilot tunnels and the running tunnels which will be enlarged to create the 58&apos;W x 44&apos;H x 700&apos;(+)L (17.6m x 13.3m x 212m +) stations. The information was complete enough to permit the design engineer to visualize the geologic structure and compute loads for the various types of rock conditions. It was therefore possible to determine the size and spacing of the steel sets for the several different conditions of rock structure encountered in the pilot tunnels.

Jan 1, 1976

By M. A. Halim, V. I. Lakshmanan, Z. Jankovic

An innovative mixed-chloride process for the separation of iron from lateritic ore is described. The separation of Fe(III) from leach liquor is an important process step for the recovery of nickel and cobalt. The patented process of Process Research ORTECH Inc. uses a lixiviant containing hydrochloric acid (HCl) and magnesium chloride (MgCl2) for the leaching of lateritic ores/concentrates followed by the selective solvent extraction step of Fe(III) over other value metals such as Ni and Co. The use of MgCl2 increases the activity of the hydrogen ion in the lixiviant, which reduces the consumption of HCl in the leaching stage and enhances the formation of HFeCl4-, thereby increasing the solvent extraction efficiency of Fe(III) with ketone. The process produces high purity iron oxide (Fe2O3) and regenerates HCl by the pyrohydrolysis of the FeCl3 rich pregnant strip solution. The developed process flowsheet is in closed loop, economically attractive and environmentally friendly.

Jan 1, 2015

By M. Ramström

"In 2002, Atlas Copco Rock Drills AB released the new rig control system (RCS) technology for all of its drill rig types. RCS opened the way for a new generation of computerized drill rigs based on modern, standard PC-computer technology. Drilling accuracy, information logging, reduction in manpower in some types, and serviceability have all taken a quantum leap forward when compared with previous generations of drill rigs. RCS is modularized and distributed by means of CAN-bus technology. This technology, which is well proven in automobile applications, forms the communication backbone of the rig. The modularity facilitates almost unlimited possibilities for the expansion and adaptation of drill rig functions."

Jan 1, 2005

By James M. Baugher, Donald W. Conrad, William J. Wiehagen

This report describes a process for quickly developing information that is useful for skills training. The process is called job training analysis (JTA). Its main use is to structure skills training at the jobsite. JTA supports structured skills training by identifying the job duties, tasks, and steps and the reasons why those job components are important. The outcome of the JTA process is a worksheet—a training outline based on the knowledge and expertise of experienced workers. Time invested in developing a JTA will result in significantly more time saved when it is used appropriately by skilled trainers. Like a roadmap, JTA saves time and energy. Experimental work at several mine sites helped document, refine, and validate the JTA process. JTAs for two mining jobs—roof bolting and lift truck operation—at two different mine sites are used to illustrate some of the concepts and the specific JTA process described in this report. The work at these two sites was influenced by cooperative work between the Mine Safety and Health Administration (MSHA) and the National Institute for Occupational Safety and Health (NIOSH) at several other mine sites and prior collaborative work with the U.S. Navy. The mining JTA process is grounded within the military research on the design of instructional systems. MSHA and NIOSH worked to simplify and apply the military training development model for mining industry use through collaborative work at several mine sites. The JTA process involves three activities: (1) planning, (2) a 1- to 3-day workshop where the JTA is developed using facilitated work with subject-matter experts, and (3) followup. Guidelines and considerations for each of these activities are included. Results indicate that the JTA process has been well received and valued by mining industry participants. It blends aspects of health and safety, production, maintenance, and crew coordination.

Jan 8, 2006

By M Lee, J F. Carswell, G Reitsema

"The increased costs of underground mining have continually challenged engineers to identify opportunities for alternatives to common approaches to underground development. Considerations to the design of horizontal and vertical development at the Dugald River mine targeted inclined raise boring to reduce horizontal development, not only to reduce cost, but to allow development activities to focus on other areas of the mine.The mine plan consists of 50 raise bored ventilation shafts, of which 17 have been mined to date with diameters ranging from 3.1 m to 5 m and lengths from 30 m to 200 m. The expected performance and stability of these shafts has been determined using methodologies proposed by McCracken and Stacey (1989) and further refined by Peck, Coombes and Lee (2011). Actual raise performances have been collated and compared to a database of raise bore performances across Australia as presented by Coombes, Lee and Peck (2011), and form a database of raise bore performance specific to Dugald River.Opportunities to further optimise the mine plan and reduce costs have seen the introduction of large diameter-inclined raise bored ventilation shafts to minimise the required lateral development to connect the ventilation circuits. Large diameter inclined shafts ranging between 3.1 m and 4.5 m in diameter have been successfully mined with dips down to 70°, reducing the cost of lateral development by more than $1 million over the next two years.Both technical and operational challenges were overcome in the mining of large diameter-inclined raise bores, including modification of: existing methodologies of assessing shaft wall stability for inclined raises. These included variations of the McCracken and Stacey method and the utilisation of the modified stability number (N’) previously developed for stope performance (Potvin, 1988). both the collar and toe development profiles, including the general set-up of the raise bore drill rig to reduce the operational risks associated with angled raises.Due to their success, inclined raises have been designed for subsequent stages of the life-of-mine ventilation system at Dugald River. This has resulted in significant capital cost savings for the mine.CITATION:Carswell, J F, Reitsema, G and Lee, M, 2017. Vertical and inclined raise bore performance at Dugald River mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 313–320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By F. Díaz-Fierros, D. Rubinos, M. T. Barral

The present work explores the reutilization of red mud, an industrial waste arising from the production of alumina, as a component of isolation technologies for hazardous substances. The work involved the study and optimisation of the geotechnical properties of red mud in conjunction with adsorption experiments of As(V) and Hg(II). The results from both types of experiments were integrated in a dispersion-diffusion model to calculate migration curves and minimum thickness of the red mud compacted layer. The geotechnical studies showed that compaction increased the stability and decreased the hydraulic conductivity of red mud barrier. Red mud sorbed high amounts of As (up to 44 mmmol kg-1) and Hg (up to 9.2 mmmol kg-1). The calculated minimum thickness of the red mud barrier was 1-10 cm for As and 2-19 cm for Hg, for an operation period of 35 years. The results obtained let to conclude that the reuse of red mud as a component of isolation systems of hazardous substances represents a viable alternative use of this residue.

Jan 1, 2011

By Allan MacRae

Freeport-McMoRan Inc. operates an ISASMELTTM furnace for the smelting of copper concentrate at the Miami Smelter in Claypool, Arizona. In May 2017, the furnace was restarted after incorporating newly designed copper cooling elements from just above the tap hole to the underside of the roof. The objective of the improved cooling design was to extend campaign life by eliminating existing failure mechanisms with the wall refractory. In addition to upgraded bathline coolers and complete coverage of the gas offtake transition, or ‘kettle’, with plate coolers, a novel arrangement of coolers was installed in the remaining freeboard area. The shell required significant cutting and re-stiffening, as well as extensive modification of the cooling water piping. Based on performance observed to date, it is expected that smelter throughput will be increased due to extended ISASMELTTM refractory campaign life.

By G Harbort, D Zoetbrood

"The Phu Kham copper-gold operation in the Laos People’s Democratic Republic (PDR) is owned and operated by Phu Bia Mining Limited. PanAust Limited holds a 90 per cent interest in Phu Bia Mining Limited, with the remaining ten per cent held by the Laos PDR Government.The original 12 Mt/a copper-gold concentrator at Phu Kham commenced production in April 2008. An incremental improvement program resulted in a number of circuit changes being incorporated by 2011, including conversion of conditioning tanks to flotation cells and the installation of a Jameson Cell cleaner scalper. In 2012 the Phu Kham Upgrade Project was commissioned to increase throughput to 18 Mt/a. In April, 2013 the Phu Kham Increased Recovery Project was commissioned to maximise performance by debottlenecking the plant IsaMill&#8482; regrind and cleaning capacity.With the variable mineralogy of Phu Kham ore, control of the c concentrate regrind circuit is essential in terms of achieving effective liberation to maintain concentrator performance. On a routine basis laboratory regrind signature plot data is compared with daily surveys of the operational IsaMills&#8482;. More extensive surveys are also conducted to determine size distribution on a mineralogical basis and the effect of fine regrinding on pulp electrochemistry and flotation performance. This paper provides a review of the operating performance of the Phu Kham IsaMills&#8482; with regard to power draw, feed and product size distribution, feed per cent solids, mineralogy and pulp electrochemistry. Operating performance is compared with the IsaMill&#8482; signature plot test for predicting performance.Citation:Harbort, G, Zoetbrood, D and McNab, B, 2016. Operating Performance of the Phu Kham IsaMill™, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 39&ndash;50 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By J. Levin

The Bond standard grindability test provides a Work Index that is widely used to estimate the energy required for grinding, but the test cannot be applied to fine materials such as plant tailings and middlings. For such materials, a comparative grinding test must be used in which a reference material from an operating plant is ground in a laboratory mill to determine the &apos;equivalent&apos; energy consumption per revolution of the laboratory mill. As the Bond grindability test mill and its operating conditions are specified, its equivalent energy consumption per revolution should be a constant, here designated as B. Once B has been determined, the mill can be used to estimate the grindability of fine materials without the need for reference materials. A value of B can be calculated from any Bond grindability test, and 245 tests that were conducted at Mintek were examined to determine its value. A wide range of values was found, but most of them were grouped around 198 x 10- 7 kWh/rev, which is taken as the best estimate of B that is available at present. Values of B that are not close to this figure are obtained from materials for which the Bond grindability test gives misleading or &apos;spurious&apos; Work Indexes. These spurious Work Indexes lead to the apparent departure of B from its true value. Some limitations of the Bond grindability test arise from its use of a mill without litters and of screening, instead of classification, to close the circuit.

Jan 1, 1989

By Mukesh K. Agarwala

Alloy composite parts were made from powders by Selective Laser Sintering (SLS). SLS is a rapid prototyping process that uses data from CADICAMICAE systems to guide a laser beam and rapidly form 3-D prototype parts from powders without any part specific tooling. In this study, Bronze-Nickel parts made by SLS were studied for their mechanical properties. To make the parts structurally sound, SLS parts were further processed by conventional isothermal sintering, without loss of shape. The resultant densification and mechanical properties were studied and related to microstructures and P/M densification models. These results were then correlated to the SLS processing parameters.

Jan 1, 1994

By J. L. Eakin

A method was developed by the Bureau of Mines in the laboratory and in the field to relieve capillary waterblocks in gas wells. Impaired gas permeability was improved by this inexpensive chemical treatment which lowers the surface tension of the water held in the capillaries of the formation. Effectiveness of the alcohol-surfactant treatment was tested with a variety of chemicals and with sandstone cores cut from rocks having relatively low permeability. Field tests on 20 gas-producing and storage wells demonstrated the effectiveness and limitations of the method. The productive capacity of some wells was doubled by the treatment. The final test was evaluated by the neutron logging technique for measuring changes in apparent liquid saturation. Maximum apparent liquid saturation was reduced by 52 percent; gas production rate increased from 2.3 to 3.5 MMcfd (million cubic feet per day).

Jan 1, 1965

By Wenjun Duan, Qingbo Yu, Qin Qin, Junxiang Liu

In the study, the coke-oven gas (COG)-steam reforming process using hot blast furnace slag (BFS) as the heat carrier is explored for producing hydrogen and recovering high-grade waste heat of hot BFS. The method of the Gibbs energy minimization approach through Lagrange multiplier is adopted in the thermodynamic analysis of reforming process. The simulation is carried out to study the operation pressure, temperature and steam to carbon ratio (S/C) based on the chemical equilibrium calculations. The optimal operation conditions are determined to improve the yield and fraction of hydrogen in the COG-steam reforming process. The results suggest that the preferential operation conditions for COG-steam reforming process to produce hydrogen are achieved at 600ºC, 1.5MPa and S/C (5.0). Due to the CaO and other melts in BFS, CH4, CO and CO2 in COG are converted and removed efficiently, especially CO2. The hydrogen fraction reaches to 86.7% and its production is about 1.22mol with 1mol of the COG.

Jan 1, 2016

By William Brinkman, Mark Jolly, Nasim Soleimanian, Karl Dearn, Oliver Brinkman

"Glass manufacturing is a heat intensive process. There is a direct correlation between the batch distribution techniques and the furnace energy consumption, productivity, and quality of the glass manufactured. All four major segments (float, container, fibre, and specialty glasses) would benefit from using an optimised batch distribution technique where possible. Oscillating batch chargers (OBC) have been in use since the early 70s, despite their superior batch shape, coverage, and in turn positive effects on the energy consumption and productivity of the furnace they are almost exclusively used in container glass manufacturing. The OBC’s main difference compared with other charging methods is its ability to directly influence the batch initial velocity. This paper reports on results achieved in CFD models (GFM) used to study effect of the machine on the overall energy consumption in the doghouse and the melt space.IntroductionGlass manufacturing can be divided to four major segments float glass, container glass, fiberglass, and specialty glasses. The financial cost of manufacture, its impact on the environment, lack of standardisation and mounting pressure imposed by the authorities for reduction in emissions means that the industry and its suppliers are utilising CFD modelling in order to tackle these challenges. The need for high temperature to create and maintain the viscous flow, homogenisation of the glass melt, and maintenance of the process to allow continuous output of glass of the right quality are the contributors to the energy intensive activities that are involved in continuous glass manufacturing. This in turn has resulted in design of large container glass furnaces which have high energy consumption, low specific performance, and high CO2 emissions where the most efficient furnaces in the container glass sector have a specific primary energy consumption of 3.8 GJ /tonne of glass at a level of 50% cullet in the batch making even very small improvements in efficiency by operation optimisation a value adding activity [1-14].The theoretical calculated energy required to melt glass is 2 to 3 times less than the energy actually used to melt glass as a result of glass melt passing a zone 5 to 8 times before leaving the tank.[8]. This causes contamination as the result of mixing between the completely molten glass free from bubbles returning to the batch area where there is freshly molten non-homogeneous glass, still containing very large numbers of bubbles and un-molten batch. At high temperature some components are dissolved rather than melted. Given that an un-molten batch is a good thermal insulator, it can be transported a long way into the furnace, increasing the need for homogenization which also increases the glass residence time of glass melt. This is why large unbroken strings of batch should be avoided, as should an overall blanket without gaps."

Jan 1, 2014