Search Documents

By J. J. Gilman

WHEN a cleavage crack that is moving through a crystal intersects a screw dislocation, a jog is created in the crack front. As the crack continues to move, the jog leaves behind a cleavage step. This mechanism was proposed by Amelinckx and Votava,' Pratt, bnd Gilmanh t about the same time. At that time the evidence for the mechanism was largely indirect. Other evidence has been presented by Low, Bilby and Smith,5 and Forty.' It is the purpose of this paper to present more direct evidence of this mechanism and to show that observations of cleavage steps can be used to detect screw dislocations. Experimental Lithium-fluoride crystals that were purchased from the Harshaw Chemical Company, as well as natural mineral crystals and metal crystals, were used in the experiments. Although cleavage steps can be observed on transparent crystals with a metallurgical microscope, the contrast is poor. Marked improvement in the contrast is obtained by depositing thin (1000A) films of silver or aluminum onto the surfaces. The contrast also can be improved by using a phase-contrast microscope, but the simpler silvering method gives just as good results. Tolansky interferometric microscopy, and electron microscopy were used to measure the heights of cleavage steps. The etching techniques developed by Gilman and Johnstonh ere used to detect dislocations in the LiF crystals. Results The dislocations that create cleavage steps can originate in three ways: a) They can be grown into crystals b) They can be introduced by plastic deformation prior to cleavage c) They can be formed just in front of the tip of a propagating cleavage crack.' These three situations will be considered in turn. Grown-in Dislocations—It is not possible to see the individual monomolecular cleavage steps that emanate from isolated screw dislocations in crystals.

Jan 1, 1959

By Richard Ely

Conservation Means Preservation, Improvement, Justice CONSERVATION, narrowly and strictly considered, means the preservation in unimpaired efficiency of the resources of the earth; or in a condition so nearly unimpaired as the nature of the case, or wise exhaustion, admits. And broadly considered, it means more than the word itself implies, for it naturally includes an examination of methods whereby the natural inheritance of the human race. may he improved; and still more broadly considered-and as used in popular discussion-it includes a treatment of the effects of productive conservation measures upon distribution. We shall give our attention briefly to the main points in this informal definition before we pass on to the thesis that conservation is largely a matter of property relations-that a wise conservation policy means wise property relations. Preservation of Natural Resources First, conservation suggests simply preservation, and, in the treatment of the subject which we have had in the United States, emphasis has been laid upon the past and present waste of natural resources and upon the means of putting a stop to this waste. The forests have been depleted; soil has been washed by rapidly flowing surface water from mountain sides. These rapidly flowing waters have produced high streams and devastating inundations, followed by low streams and impeded navigation. The forests have, moreover, been so removed as to bring great danger of fire, and destructive conflagrations have resulted in large waste of resources, including in some cases a destruction of the humus, supplying essential elements in the fertile soil. As a remedy we must have measures to reforest mountain sides, and this means large social control, very frequently taking the form of public ownership and management; but in addition we always find actual and proposed

Jan 2, 1916

By C. I. Ware

The phrase ?back to basics? is used to describe the fundamental principles and philosophies on which a successful mining operation is based. At Richards Bay Minerals (RBM), ?back-to-basics? (BTB) has been implemented as a continuous process to probe operational functions with a view to increase production without capital expenditure. It also ensures that the fundamentals of dredge mining are understood and adhered to. BTB is based on the principle that people drive organizations, necessitating an interactive implementation approach. At the RBM mine this entails a three-pronged approach, namely practical training, teamwork initiatives and the use of lean Six Sigma methodology. It is the latter on which this paper will focus. The lean Six Sigma methodology is successful in identifying, managing and documenting BTB projects, while team work initiatives are integral to successful project implementation. This paper describes two examples of how the Six Sigma methodology can be applied to a dredge mining operation. The first example focuses on the improvement of Mining Pond Echo (MPE) plant throughput by reducing the lost opportunity (non-production) due to tails downtime. The project was successful in increasing plant throughput by 4.5%. This was achieved by increasing the tails disposal system availability by running MPE as a four tails lines operation and focusing on causes of tails production downtime. Subsequently, the tails system at MPE is no longer the production bottleneck. Second, the Six Sigma methodology was successfully applied at Mining Pond Charlie (MPC) to increase the primary dredger throughput by 4.6% through focusing on the dredging technique and maintenance issues. This project highlighted the need for trend analyses to ensure an effective dredging technique, coupled with simple production documentation, which also ensures a focus on maintenance. Keywords: Back to basics, Six Sigma, training, teamwork, throughput improvement, tails, dredger.

Jan 1, 2007

By J. E. Clennell

It is a common observation that the improvements introduced in practice since the first announcement of the cyanide process have been almost entirely mechanical. Although .a good deal of study land research has been devoted to the chemical problems [involved, the results obtained appear trifling in comparison. Few of the suggested modifications in the chemical treatment have come into practical use and those only in limited fields. Nevertheless, if we study the recent history of the cyanogen compounds from a somewhat broader standpoint, we shall find that considerable additions have been made, not only to our knowledge of their chemical properties, but also to their applications for industrial purposes. The present review of these advances naturally falls into two divisions: (1) processes involved in the treatment of ores; (2) manufacture of cyanides and other related compounds. Part I. Advances in the Chemistry of Ore Treatment by Cyanide In the attempt to extend the scope of the process, various ores have been encountered which contain gold and silver in such forms that they will not yield satisfactorily to ordinary methods of cyanide treatment. In some cases the difficulty is due to the excessive action on the solution of base metals present in the ore; in others, to the occurrence of minerals such as dyscrasite (the native alloy of antimony and silver), or a supposed oxidized manganese compound containing silver, which are either altogether insoluble in or very slightly attacked by cyanide. A particularly troublesome case is that of the so-called "graphitic" ores, containing carbon in some form which has the property of precipitating gold and silver already dissolved. Other efforts have been directed to improving extraction by electrolysis of working solutions, and by addition of various chemicals with or without electrolysis; to the diminution of cyanide consumption by "re-

Jan 1, 1916

By Simon Pelletier, Jose Delgadillo, Dave Page, Pramod Kumar, Raj Rajamani, Dilek Alkac, Martin Fillion

"In general, many past works examine mill load, mill power, shell lifter design etc with a view to improving the mill capacity. On the contrary, only a handful of papers have addressed the transport of fine slurry through the pulp lifters. We present the flow dynamics of pulp lifters via laboratory scale experiments, high speed photography and modeling with computational fluid dynamics. Next, the flow behaviour in ArcelorMittal’s Mont-Wright autogenous mill discharge flow is examined. In an effort to improve mill throughput, a comprehensive simulation and plant scale study of the mill was taken up with a focus on the shell and pulp lifter design. The shell lifter was found to be at its optimum limit for breakage of ore particles given the constraints of wear life and occupied volume. Next, the pulp lifter study was taken up with computational fluid flow code and discrete element code. The simulations directly showed that there was considerable carry-over of slurry. This effect was traced to the area restriction in the pulp lifter channels. Further, crash-stop studies confirmed slurry pooling within the mill. Thus it was readily apparent that mill throughput can be increased if the pulp-lifter could be redesigned. Consequently, the discharger section of the pulp-lifter was redesigned.First, this paper outlines the modeling in laboratory scale studies and plant scale studies leading up to the discharger design. Next, the discharge flow in seven different published mill surveys is predicted with computational fluid dynamics (CFD) methodology shown here. Finally, Mont-Wright mill circuit performance before and after the discharger redesign is described. The usefulness of fluid flow simulations in the design of pulp-lifters is emphasized."

Jan 1, 2012

Since I first enrolled to study Mining Engineering, the idea of working with big machinery and explosives has always appealed to me. After a few courses at uni, combined with vacation work and a number of presentations at the New LeadersÆ Conferences I had attended, I began to realise that the explosives side seemed to have more appeal than the others. As I look back on the past two and a half years that I have spent with Orica Australia Pty Ltd as part of their graduate program, I would have never imagined the dynamics of explosives in mining. This I put down to the ever changing and rapid development in technology converting blasting techniques into a defined predictable science. The opportunities I have been given have delivered all the appeals from when I first started my study. As a result of my entry into a profession that uses explosives to deliver broken rock in a range of mining and construction projects, through the use of advanced blasting technology and products, my experiences have been wide and varied. These experiences have included the use of OricaÆs i-konÖ detonator technology and blast design software to allow for blasting operations to occur in a range of environmentally sensitive quarrying and construction projects throughout New Zealand, to the implementation of various Orica blast based services aimed at improving dragline dig performance and reducing coal loss thus improve overall mine sustainability in the coal mines of Central Queensland, to the advanced utilisation of Orica explosive products and technology in a number of the worlds largest copper mines in Chile. I have witnessed first hand the blasting technology available within Orica Mining Services to both deliver fundamental changes in mining results and in turn kick off my career with a bang.

Jan 1, 2009

By William Petruk, Donald Leroux, Michael Cooper

"Brunswick's primary flotation circuit (CuPb) produces a low grade concentrate containing considerable amounts of undesirable sphalerite and pyrite. To determine the cause of the poor selectivity, a series of Quantitative Mineralogical Analyses (QMA) were performed on several CuPb circuit streams. It was observed that significant fractions of sphalerite and pyrite reporting to the concentrate was liberated, meaning that their depression was not complete. The study highlighted the need for some R&D efforts to be spent in sulphide flotation fundamentals.IntroductionThe viability of many mining projects strongly depends on the performance of their concentrators. More than ever, competitive grade concentrate and high metal recoveries are criteria of paramount economic importance. The selectivity of solid/solid separation processes used in concentrators must be maintained at high levels or continuously improved.Flotation is the solid/solid separation process used by most base metal producers. In spite of its low operating cost, flotation remains a very complex process. To make it selective, precise reagent dosages and electrochemical conditions must be maintained. The difficulty in controlling flotation lies in the numerous heterogeneous reactions that can take place between the different solid, liquid and gaseous phases involved. This complex chemistry makes flotation selectivity difficult to understand and, therefore, to improve from a theoretical point of view.Brunswick Mining and Smelting, near Bathurst N.B., operates a 10500 tpd concentrator which produces four concentrates through five stages of sequential flotation (Figure I). Various reagents are added at key process stages while the ore undergoes different electrochemical conditions. Although the selectivity is important at all stages, the performance of the very first separation, the CuPb circuit, is the most critical. It is here where mineral misplacement to the wrong stream has the greatest economic consequences."

Jan 1, 1996

By C. H. Hitchcock

History In approaching the subject of diamond-drilling practice, a brief history of the origin and development of the diamond drill may be of interest. The use of black diamonds for boring holes in rock was discovered in 1863 by Rudolph Leschot, a French engineer. In 1864, he employed a diamond bit to bore holes for blasting purposes in the construction of the Mont Cenis tunnel between France and Italy. The method was introduced and developed in the United States in the late sixties. The first deep hole was drilled for coal in 1870, near Pottsville, Penn., by M. C. Bullock. This hole was seven hundred and fifty feet deep. It can be inferred that the diamond drill was introduced into Canada in 1871, when a bore-hole, known as Harper's bore-hole, was drilled for coal at Springhill, Cumberland county, Nova Scotia; and at the old Silver Islet mine, near Port Arthur, the diamond drill was in use as early as 1872. Diamond Drills While M. C. Bullock was developing the diamond drill for exploratory work, the Sullivan Machine Company, of Claremont, N.H., was developing the diamond channelers and gadders for quarry work. These quarry machines were very successful until the high price of black diamonds became prohibitive. In 1878, Albert Ball, chief engineer of the Sullivan Machine Company, designed the Sullivan diamond drill so well known today. The first of these drills went to the Lake Superior iron ranges. After 1880, use of the diamond drill expanded rapidly and spread to all parts of the world where exploratory work was being done. In recent years, the type of diamond drill has not changed much, but better material is going into its construction. Steel castings have replaced cast-iron. Ball and roller bearings are now used instead of brasses and babbits. Gun lubrication has eliminated the oil-can. These improvements make a drill that can be operated for long periods without expense for repairs.

Jan 1, 1933

By A. Gontijo, A. Matos, P. Lincoln, L. Fonsecail

This paper investigates how to manage and model the vibrations caused by rock blasting in a Brazilian underground mine. Considering the frequent detonations and the previous lack of effective vibration control, understanding, and reducing the impact of these seismic waves is critical. We emphasize the use of the near field model technique, which considers the varied physical properties of different rocks, optimizes blasting plans, and minimizes damage to the rock mass. We detail a case study that demonstrates a comprehensive approach to vibration control. The discussion includes the creation of a monitoring plan, the methodology used, results and the specific challenges and solutions found during the blasting process. This study provides a practical guide for similar future projects. Finally, we present a predictive model based on the collected data, offering insights into the vibrations caused by blasting. This model helps decision-makers minimize the risk of displacing rock blocks in the blasting area, improving safety and operational efficiency

Jan 1, 2024

By Albert G. Zima

ACCORDING to recently published statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed.. Today, 'however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. DRILL TOOLS Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brinell hardness

Jan 1, 1935

By K. Adham, T. Buchholz

"Significant capacity increases to meet new production demands can often be fulfilled through debottlenecking of an existing production facility, rather than the more expensive option of building new plants and facing new environmental and infrastructure challenges. To achieve that goal, it is important to model and calculate the existing ultimate capacity of each processing plant area, and that of each key equipment sector within the plant areas. This paper describes a methodology of how process modeling tools can be used to simulate the processing steps, how to estimate their existing and ultimate capacities, and how to determine the sweet-spots (minimum cost points) for a plant expansion – leading to a road map of the subsequent debottlenecking project implementation.The debottlenecking technique is presented through a generic work-flow narrative which can be applied to different mineral processing studies, starting with establishment of heat-and-mass balances, drawing a bottleneck diagram, brainstorming capacity increase options, and preparing a cost-capacity curve. Hatch has successfully applied this technique to a number of plant capacity studies, with great benefits to our industrial clients.INTRODUCTIONWith the softening of the metals and minerals prices, and the escalated costs of building new processing plants, it is now economically more viable to improve and debottleneck the existing facilities, rather than build new ones. However, spending new money on old plants requires careful considerations, in order to identify the most economically advantageous incremental steps of improvement and the best potential returns on investment. Process modeling, hand in hand with plant measurements, can identify the best scenarios to balance the three aspects of plant capacity (nameplate, utilization and yield), both at the global and the individual system and subsystem levels."

Jan 1, 2016

By Albert G. Zima

According to recently puhlished statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. Drill Tools Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brine11 hardness number. Drill and reamer cutters are generally of the movable type; i.e., serrated cones, cylinders or disks, which can readily be replaced when

Jan 1, 1935

By Albert G. Zima

According to recently puhlished statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. Drill Tools Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brine11 hardness number. Drill and reamer cutters are generally of the movable type; i.e., serrated cones, cylinders or disks, which can readily be replaced when

Jan 1, 1935

By A. I. A. Salama, M. W. Mikhail, R. J. Mikula

"The Coal Research Laboratory (CRL) of CANMET along with other research organizations in coal-producing countries envisage major benefits from computer applications in coal preparation, Some of these benefits are greater system flexibility, improved coal preparation plant performance efficiency and efficient utilization of manpower, all of which result in economic benefits. Computers can be applied for both on-line and off-line purposes; this paper focuses on the on-line applications from the process control point of view.A critical discussion of the different analog and digital process control systems is presented. Recent developments in Great Britain, West Germany, Poland and Australia on automation and instrumentation using on-line measurements of coal ash and moisture contents are identified.The CRL research and development strategy aimed at achieving on-line computer control of an automated coal preparation plant is presented.IntroductionIn the past twenty years an enormous progress in the area of computer technology has been noticed. Computer applications in industrial processes offer greater system flexibility, improved plant performance efficiency and efficient utilization of manpower. Significant computer control development in mineral processing has already been achieved. Although progress has been made in the area of computer applications in coal preparation, more effort is needed to utilize the full potential.The computer applications in coal preparation can be viewed as off-line and on-line. Considerable progress has been reported in the area of off-line computer applications, especially in the areas of modelling, performance evaluation/prediction and statistical analysis. However, only modest progress in on-line applications has been reported(1-7). This paper will focus on: online instrumentation and process control applications, different analog and/or digital control systems, on-line automation and instrumentation in other countries and CRL strategy toward pilot plant automation."

Jan 1, 1985

By F. Kitzinger

Electromagnetic testing of wire rope has become more and more reliable over the past two decades. This improvement is partly a result of an unprecedented progress of electronic technology, which permitted the development of a new breed of testing instruments. There are two basic methods for the electromagnetic testing of wire ropes, the AC method and the DC method. Both methods rely on magnetic field disturbance caused by mechanical anomalies in the rope structure. The wire rope under test is passed through a magnetic excitation field, which can be a weak alternating field or a strong static field. Because the alternating field is produced by an alternating current, these instruments are of the AC type(l). In the early days of ND-testing, strong permanent magnets were not yet available; therefore, the static magnetic field was produced electromagnetically with direct current. Instruments based on static excitation are still called DC instruments(2), even though the field is now produced by a permanent magnet. Both these methods have certain characteristic features. The AC method can detect loss of metallic area caused by corrosion or other effects, whereas localized faults such as broken wires are better detected by the DC instruments . The basic principles of the wire rope testers have remained unchanged over the years and the improvements present in the new instruments usually reside in the signal processing and recording sections. The Instrumentation Department of the Noranda Research Centre* has been involved in a four-year development program which resulted in a new type of wire rope tester, the Magnographv** . This new instrument in many ways represents a considerable departure from the traditional wire rope testers. The Magnograph has already been patented in Canada and the U.S.A.(3), and patent applications are pending in other countries.

Jan 1, 1979

The first grant of land rights in Australia was pursuant to the Aboriginal Land Rights (Northern Territory) Act 1976. That Act has been at the core of the dispute between land rights and miners' rights. The mining industry believes that the Act, in giving a right of veto to Aborigines with respect to exploration and mining on Aboriginal land, has been responsible for a stagnation in exploration amd mining activity in the Northern Territory. In February 1985 the Commonwealth Government released for public comment its preferred model for national land rights legislation. The model has been opposed by the mining industry because it believes, first, that land rights is a matter which should be left to the States and, secondly, that the detailed mechanisms contained in the model constrain the industry in the manner of the Northern Territory legislation. Aboriginal leaders have opposed the model because it does not, in their view, measure up to undertakings given by the Commonwealth Government and, in addition, it provides for amendments to the Northern Territory legislation which are likely to result in the loss of the Aboriginal veto right. Are land rights and miner's rights compatible? The answer is yes provided all parties, including Governments, are prepared to talk and compromise and Governments recognise that the grant of land rights and any control by the Aboriginal people of exploration and mining on their land is not a substitute for raising the living standards of Aborigines as a significant group of disadvantaged Australians.

Jan 1, 1986

In the leaching and recovery of gold from copper containing gold ores using cyanidation, some copper minerals also dissolve which can have a detrimental effect on the process efficiency and economics. There are also environmental concerns with current operations discharging cyanide and copper cyanide species into tailings dams, and strict regulations prohibit this for greenfield plants. Cyanide destruction however is not an economic option for new plants treating copper-gold ores. This paper evaluates a potential recovery process to overcome the copper cyanide problem. Despite gold dissolution occurring in copper cyanide solutions having no free cyanide, gold recovery from ores is lower compared to free cyanide. Thus, cyanide addition has to be optimised to maximise the gold recovery whilst endeavouring to eliminate free cyanide at the completion of leaching (CN:Cu less than 3:1). Subsequently, copper cyanide can be recovered using activated carbon. The loaded copper cyanide is easily recovered from the carbon with a cyanide soak and distilled water wash such that the eluted CN :Cu ratio is less than 4:1. The copper could be recovered efficiently by electrowinning, by decreasing the pH of the eluant to 5. The remaining cyanide solution, after electrowinning, is then neutralised to form NaCN and recycled.

Jan 1, 2005

By Diana Drinkwater

As ore grades decline, ore deposits get harder and mineralogical complexity increases, metallurgical skills are more important than ever to ensure that today?s mining operations are operating efficiently and profitably. Yet specialist undergraduate degree programs have all but disappeared and metallurgical skills training for graduate engineers in the workspace if often haphazard. In response to this situation, specialists at the JK Centre in Queensland, Australia, have put together a professional development program designed to fast-track skills development for early career metallurgical professionals. The program, called ?MetSkill ® ?, is offered as a group training package for young metallurgists in the workplace. It is centred on a meaningful technical investigation negotiated between the JK Centre delivery team and the client company. As well as learning about project management and data collection and analysis, the participants study specialist topics such as comminution, flotation and mineralogy under the tutelage of senior research and consulting professionals. The technical investigation provides an opportunity for immediate practice of these new skills and JK Centre specialists are on hand to provide feedback and support throughout the program. The participants are employed across different operations in Australia and the Asia-Pacific, and although they occasionally come together for group training activities they are often separated by considerable distance. Specialist educational professionals from The University of Queensland have provided an innovative web platform to support collaboration and communication between all participants. This paper will describe the MetSkill ® program in detail, as well as providing a report on its initial roll-out to 2 groups of Australian graduate metallurgists in 2012

Sep 1, 2012

By S Long, A J Koen, D MacKay

The Mt Wright Underground Mine is located near the town of Ravenswood in North Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited. Following the evolution of the mine plan through a number of stages, the ‘sublevel shrinkage (SLS) with continuous fill’ mining method was implemented in 2010 to extract the Mt Wright orebody. The production front in this mining method is similar to a sublevel cave (SLC) operation; however, backfill is placed into the top of the production zone as opposed to requiring the overlying strata to cave.Continuous fill to replace the void created by extracting the ore was required to manage the potential risks associated with the proximity of infrastructure to the footwall, associated long-term stability and air blast potential due to the limited ‘cavability’ of the material within the cave zone. The available fill material was sourced from a disused waste dump from a previous open pit operation, which introduced further technical and economic risks associated with dilution from ‘no grade’ broken material. Procedures and processes to manage these risks have been incorporated into the operation of the mine.Despite encountering a number of challenges, the SLS method has been in use for approximately three years at Mt Wright and has proven to be viable economically, technically and operationally. This paper will discuss the challenges encountered and what was done to overcome them, the operational and financial performance to date, along with the outcomes of some successful continuous improvement projects that have improved the efficiency of the operation.CITATION:Mackay, D, Long, S and Koen, A J, 2014. Sublevel shrinkage – the Mt Wright story, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 205–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By J. Kenneth Wittle

The DC Graphite Melter has been shown to be capable of processing radioactive waste materials. The process is characterized by its high temperature capability and operation in a closed system. From an environmental perspective, the control of emissions coupled with destruction for hazardous organic materials is mandatory. These same characteristics may be applicable to the minerals processing industry. Under normal operation, the system reaches temperatures for nominal operation of 1600°C, with an arc temperature in the order of 5000°C. The system temperature is determined by the melt temperature of the material being processed. In testing of a 750 lb/hour unit, temperatures of 2200°C were reached. Current focus is on finding waste treatment and metals recovery opportunities in the metals processing industry for his innovative technology.

Jan 1, 1999