Search Documents

By Lance Rasband, Richard Hanke

"Seattle Tunnel Partners (STP) started mining on Seattle’s SR99 tunnel on July 30, 2013, working slowly through a 15 ft (4.6 m) thick fiber-reinforced concrete headwall. Once through the headwall, the machine would move through roughly 400 lineal ft (122 m) of jet grout-improved soil at a rate slightly over 6 ft (1.8 m) per day. It was anticipated that once through the improved area, Bertha—the world’s largest tunnel boring machine—would move at a rate of 35 ft (10.7 m) per day. By the end of October 2013, Bertha had mined roughly 430 ft (131 m), averaging 4.73 ft (1.4 m) per day, and had begun mining within native soils. By the start of December 2013, tunneling reached the 800 ft (244 m) mark and Bertha averaged 12 ft (3.7 m) per day, achieving as much as 42 ft (12.8 m) of progress on some days. However, on December 6, 2013, Bertha began to stumble and all progress quickly came to a halt. Preliminary InvestigationInitial reports stated that an obstruction had stopped the machine in its tracks. Malcolm Drilling received an early morning call on Sunday, December 8, 2013, from STP to rapidly mobilize a Bauer BG-50 drill rig with crews to investigate what was hindering Bertha’s progress. Malcolm’s equipment and crews flew into action and were completely mobilized and operational by mid-week. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic head within the ground around the machine and allow STP personnel to inspect the cutter head from within the shaft for presence of obstructions. By the close of December 2013, the wells were installed and the dewatering system was fully commissioned. STP crews were then able to inspect the cutter head and found small fragments of a steel pipe wrapped around the outside of the shield. The steel was apparently from an abandoned 10 in (0.25 m) diameter monitoring well casing previously installed by WSDOT (Washington State Department of Transportation) to monitor groundwater conditions for the design and planning of this very project. After the steel was cut out of the head and cleared from Bertha’s path, she attempted to move forward but was only able to manage a slow crawl"

Jan 1, 2015

By Robert L. Grayson

An application of goal programming (GP) in evaluation of proposed purchases of major mining machinery is presented. It incorporates historical operating data compiled on mechanical delays to production time. The goal programming technique, which is an extension of integer programming, is used to maximize an objective function. The objective function combines the capital budgeting evaluation methods of net present value, payback period, profitability index, and total net earnings as goals weighted according to a management preference. The GP method gives an optimal solution to a multiple-goal problem. A sensitivity analysis is performed to determine the effect of an increased production forecast or a tightened budget on proposal selection.

Jan 1, 1982

By Nieves Iglesias

The removal of the refractoriness of a gold bearing pyrite- arsenopyrite ore is studied. Flotation concentrates were prepared and leached with a dilute acidic ferric sulfate solution. The elemental sulfur film which forms on arsenopyrite in the oxidation process is not responsible for the low rate of the arsenic dissolution observed. A positive effect on the leaching rate is observed when Ag' is added. This pretreatment eliminates the refractory nature of concentrates.

Jan 1, 1993

By K. A. Lewandowski

Heap leaching efficiency is reduced by poor solution flow characteristics (channeling and ponding), which result from compaction and fines migration. Agglomeration of the ore can prevent compaction and immobilize fines, but copper leaching requires an acid-resistant binder to stabilize the agglomerates. Until now, there has not been a satisfactory way to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? Procedures have been developed to quantitatively determine whether a binder produces agglomerates that can withstand compaction in an acidic solution, and have identified several binders that will provide sufficiently compaction-resistant agglomerates for copper heap leaching. Keywords: Copper heap leaching, Binder performance, Compaction

Jan 1, 2010

By S. Ajima

The Naoshima Smelter and Refinery is the most important copper operation of Mitsubishi Materials Corporation. There are a Mitsubishi Continuous smelter and a conventional type of copper tankhouse. The continuous smelter with 240,000 mtpy of anode production was commissioned in May 19914 replacing two existing smelters, i.e an original Mitsubishi Process line and a conventional reverberatory furnace line. In July 1992, the copper tankhouae was expanded for the purpose to close the gap of production capacity between the smelter and the tankhouse. The cathode production capacity was increased from 13,800 to 15,800 mtpm. By these plant modifications, the distribution of minor elements was significantly changed and the impurities load is getting on increase reflecting recent shortage of clean copper concentrates supply. The paper discusses the distribution of minor elements and the impurity control strategy at the smelter end the refinery.

Jan 1, 1995

By Peter Swanson

One of the primary methods for analyzing roof stability in underground mines is the age-old method of “roof sounding” where a miner taps on the roof and listens for the hollow sound of loose blocks of rock. This paper looks at the feasibility of using noncontact laser-based vibration measurements to detect roof fall hazards with the ultimate vision of improving, expanding and automating procedures for mine roof inspection. Vibration measurements made on loose blocks of rock in underground mines are summarized and compared to estimates of fundamental resonance frequencies for rock slabs of the size responsible for highly hazardous “skin failures.” Both laser Doppler vibrometry and full-field interferometric methods are examined and are considered to be feasible methods for detecting anomalous vibrations in loose roof rocks. Results from simple laboratory experiments using laser vibrometry demonstrate some of the proposed application concepts. While considered a challenge to move these techniques from the laboratory to heavy industrial or outdoor environments, the potential for success in the current application is enhanced by the reduced requirements of qualitative analyses.

By Qingming Feng, Dongbo An, Jinhong Zhang

The application of the geopolymerization of mine tailings as construction materials is hindered by the fact that conventional geopolymerization of mine tailings usually involves a large consumption of alkali, i.e., sodium hydroxide (NaOH), and a long curing time, because of the relatively low reactivity and the high Si/Al ratio of mine tailings when compared to other active resources such as fly ash and clay minerals. The present study is focused on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. We firstly investigate the temperature effect on the alkali activation of mine tailings during geopolymerization. Secondly, the impact of additives, i.e., calcium hydroxide and aluminium oxide, on the compressive strength of samples is studied. Thirdly, different forming pressures have been applied to remove excessive alkali and its impact on samples' strength has been investigated. The results show that a 40 MPa unconfined compressive strength (UCS) can be achieved with the geopolymerization samples after mine tailings are activated by sodium hydroxide at 170°C for 1 hour with the addition of calcium hydroxide and alkali dissolved aluminium oxide, further compressed with a 10 MPa forming pressure and finally cured at 90°C for 3 days. The findings of the present work provide a novel method for the geopolymerization of mine tailings as construction materials.

Jan 1, 2014

By R. G. Achter, E. Wilson

"This paper describes the work undertaken to renovate the Pipe Open Pit drainage system, incorporating measures to improve effluent quality. It describes the technical feat of drilling an l l-inch-diameter hole from the bottom of the open pit for a distance of 1100feet to intersect an underground drift. An innovative method of checking the inclination of this hole is also described. The paper outlines the construction required on the 1500-foot level of the underground mine to facilitate water impoundment and slime settling, as well as the instrumentation for control of water flows. IntroductionThe Manitoba Division of Inco Metals Company operates two mines-an underground mine at Thompson and an open pit at Pipe. The Pipe Open Pit is located 20 miles southwest of the City of Thompson, approximately 400 miles due north of Win nipeg(Fig. 1).Surface diamond drilling of the Pipe ore body was sta rted in 1959. In 1961, a shaft was sunk to a depth o f 1,570 feet to carry out further exploration work and obtain bulk ore samples for metallurgical testing. Site preparation to mine the upper portion of the orebody as an open pit was initiated in 1966 and by late 1967, the removal of silt and clay overburden was in progress. The contractor completed the dredging in the fall of 1969. Over 12 million cubic yards of muskeg, clay and silt was removed, which in some places was 150 feet deep over the orebody. Production began in early 1971, by which time the top three benches of rock had been excavated and the orebody exposed.The Pipe No. 2 Mine main shaft was started in 1970 and completed in 1973 at a depth of 3,160 feet. Development for exploration purposes was carried out on the 1500 and 2460 levels, and permanent pumping facilities were installed.The surface dimensions of the open pit are 2,200 by 1,600 feet, with the long axis striking northeast. The walls are designed with a 45- to 50-degree slope and the ultimate design depth is 720 feet. The present depth of the pit is 520 feet and production capacity is 6,800 tons of ore per mine day."

Jan 1, 1980

By C. Richard Groves

As the level of technology applied in the electrical measurement, control, and display portions of mine hoist systems continues to advance, the issues and concerns associated with the ramifications of the application of microprocessor technology on the safety-related aspects of these systems become paramount. This report, in part tutorial, addresses several aspects of these concerns. Beginning with discussions of microprocessor-based system architectures, the report addresses some existing and anticipated uses of this technology in mine hoist systems and discusses safety related considerations associated with the areas of data derivation; control and display panels; and system reliability issues. The report concludes with electrical maintenance and inspection considerations associated with the safety assurance of microprocessor based mine hoist systems.

Jan 1, 1986

By Zhihua Wang

Through metallurgical calculation and process analysis based on metallurgical theory, it is aimed to raise the concentration of smelting oxygen and improve the update speed of reaction interface, accelerate the reaction and achieve a high-intensity smelting at the stage of converting. The PM plant has launched a theoretical research on model of high-intensity converting aiming at increasing the oxygen concentration of converting, carried out transformation of Kaldo furnace converting system, performed a series of industrial trial operations, conducted multiple rounds of tracking test and data comparison in reducing the furnace cycle, lowering the unit consumption of fuel and stabilizing the furnace lining life. The move has practically tested and verified the correctness of high-intensity smelting theory.

By F. P. Haver

The Bureau of Mines is developing a leach-electrolysis procedure to produce Special High Grade (SHG) zinc from sulfide concentrate without the generation of sulfur oxide gases. Chlorine-oxygen leaching of the concentrate yields zinc chloride (ZnCI2) which, after purification, is electrolyzed in a fused-salt cell to obtain molten zinc metal and chlorine gas for recycle. This paper describes a laboratory-scale investigation made to develop a procedure for electrowinning zinc metal from ZnC12. Zinc chloride by itself is not a suitable electrolyte because it fumes badly above its melting point and is a poor conductor of electricity. Other salts therefore must be added to prevent fuming and improve the conductivity. Optimum results were obtained with a KC1-LiCl-ZnCl2 bath at 500° C, using a current density of 5 amp/in2 and an electrode spacing of 0.5 inch. Under these conditions, SHG zinc was produced at a current efficiency of 94.3 pct and an energy requirement of 1.16 kwhr/lb. Fused-salt electrowinning eliminates the need to handle and melt cathodes and increases the production of metal per unit cell volume through the use of higher current densities than are possible with aqueous electrolysis.

Jan 1, 1976

By David A. Campbell

There has been a long history of ironmaking on the North East coast of England centered around the River Tees. The industry developed here because of the availability of good coking coals to the North in Co. Durham, and the discovery in 1851 of ironstone in the nearby Cleveland Hills, South of the .River. Cleveland ironstone is relatively poor in quality, with an iron content not exceeding h% and high proportion of sulphur and phosphorous. The iron exists in chemical association with alumina and silica, and physical beneficiation processes involve a serious loss in iron unless the upgrading is limited, when the economics of the process become doubtful. Over the years, richer foreign ores have replaced the local ironstone, and the last operating mine was closed in 1964.

Jan 1, 1982

By L. D. Tracy

This is the third of the series of reports on coal-mine royalties and leasing conditions in Illinois. The results of the study of District VI were published as Serial No. 2726, January, 1926, and those of District VIII as Serial No. 2745, April, 1926, of the Bureau of mines. The counties of Macoupin, Sangamon, and Montgomery, which are three of the principal coal-producing areas in the northern part of District VII, have been chosen for this report because these counties cover an entirely different part of the State than do the two districts already covered. Some leases in, Randolph and Washington counties are included as they are in the southern part of the district, and the data happened to be readily available.

Jan 1, 1926

By Dan Norrgran

In recent years, a great deal of attention has been focused on developing mill liners to increase wear resistance, improve grinding efficiency and reduce energy consumption in milling applications. The installation of an appropriate mill liner is critical as it affects the overall cost and product quality. A mill liner has two specific functions. The first is to protect the mill shell and mill ends from direct contact with the abrasive grinding media (in this case, the liner serves as a wear surface). The second function is to transport the grinding media, creating energy for size reduction. The liner acts as a lifter, mechanically transporting and cascading the grinding media. The mill lining is a major cost in the milling operation. The costs associated with the mill lining include the capital cost of the lining, downtime required to replace the worn liner and the labor for installation. Generally, in hard rock mining, the life of a mill liner in secondary ball mills is 12 to 24 months.

Jan 1, 2009

By R. T. Seaman

Pressure oxidative treatment of whole ores and/or mineral concentrates is used to leach or liberate metals of value for downstream recovery. Silver, when present, is often lost in processing, precipitating as a cyanide-insoluble jarosite in the residue. Depending on pressure oxidation conditions, the degree of silver loss to jarosite can vary dramatically. Batch bench-scale testwork is often performed to define that loss, and then assess the implications in continuous operations. This paper focusses specifically on the impact of CESL pressure oxidation conditions on silver recovery, and discusses limitations of batch bench-scale testing as well as means of overcoming these limitations to better predict silver recovery in the scale up from bench-scale to continuous operations. Since silver is only partially soluble in both sulphate and chloride media, it will gradually leach and deport to a jarosite as oxidation progresses. When a silver-insoluble anion, for example iodide, is dosed prior to oxidation, there is a marked improvement in silver recovery from batchgenerated residue; however, that benefit is not consistently seen in continuous operations. The difference has been attributed to the dynamic solution conditions in the batch test, specifically the first few moments of oxidation. Using these principles, a predictive correlation has been established between initial leach concentrations of iron and acid and ultimate silver recovery with iodide addition.

By B. Simonian

"The Mount Milligan mine, located in central British Columbia, began operation in September 2013 with a design nameplate capacity of 62,500 dry metric tonnes per day, using a conventional SABC grinding circuit followed by bulk sulphide flotation. Over the last few years, many changes have been implemented in order to debottleneck and optimize the comminution circuit to meet and exceed the nameplate design capacity as well as improve the metal recovery of the flotation circuit. This paper discusses changes, grouped into mechanical modifications, projects, and operational changes. The implementation of these changes as well as ongoing challenges and potential solutions will also be discussed.INTRODUCTION The Mount Milligan mine began production in the fall of 2013. It is a conventional truck-shovel open pit gold and copper mine and concentrator with a 62,500 tpd design capacity copper-gold flotation processing plant. The average head grades for the life of mine are 0.18% Cu and 0.39 g/t Au. At full capacity, the mine produces an average 400 dry tonnes per day of copper-gold concentrate containing approximately 21.5% Cu and 50-60 g/t Au. Current mine life is 21 years. This paper will discuss a selection of the operational, engineering, and administrative changes that have been made at the site since the publication of An Update on Reaching Nameplate Throughput and Continuous Improvement at Mount Milligan (Yue, 2017). PLANT FLOWSHEET CONFIGURATION Run-of-mine ore is crushed through a 60-110 gyratory crusher to a top size of seven inches. Up to 100% of the gyratory crusher product is diverted to the secondary crushing circuit by a moveable gate. The material diverted to the secondary crushing circuit is fed to a vibrating double-deck screen. The screen oversize is placed on a surge pile and reclaimed by four vibrating feeders to feed two 1250 kW standard head cone crushers in open circuit. The screen undersize is combined with the crusher discharge and returns to the conveyor feeding the coarse ore stockpile along with primary crusher product that by-passes the diverter gate."

Jan 1, 2019

By D M. Brady

Underground coal mines in Australia have embraced the use of various inertisation techniques both proactively and reactively. The use of such techniques can have a significant influence on ratios and trends used to monitor the status of the underground environment. Whilst control strategies should never be ignored in favour of preserving the integrity of ratios, the influence and significance of the changes likely to be seen should be anticipated and understood for reliable interpretation of the situation. This paper looks at the influence inertisation techniques can have on results and subsequent interpretation.CITATION:Brady, D M, 2013. The influence of inertisation techniques on gas interpretation, in Proceedings The Australian Mine Ventilation Conference , pp 259-264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By L. C. IlsLey

A list of permissible mine equipment approved by the Bureau of Mines before January 1, 1940, was published in Bureau of Mines Information Circu- lar 71103. Information Circular 71584, published as a supplement thereto, listed equipment approved during the calendar year 1940. The present list contains the information given in those two circulars, as well as approvals issued during the calendar year 1941. It embraces electrically operated air compressors, coal drills, conveyors and loading machines, electrical equipment for mine fans, mining machines and trucks, mine pumps, rock- dust distributors, room hoists, storage-battery gathering and haulage locomotives, storage-battery power trucks and shuttle cars, mine telephones, junction and distribution boxes, electric cap lamps, flame safety lamps, electric hand and trip lamps, electric flood lamps, flashlights, methane detectors, and single- and multiple-shot blasting units. The equipment listed is not approved by the Bureau of Mines until found by inspection and test to comply with minimum standards of safety as outlined in "schedules" prepared upon the basis of many years of ex- perience in dealing with safety problems confronting the coal-mining in- dustry. The use of such equipment in mines that are known to be gassy,. as well as in those that may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept informed as to the many types of machines, devices, and lamps that are available for reducing explosion and other hazards incidental to coal mining.

Apr 1, 1942

By C. L. Karr

Researchers at the University of Alabama have developed a method for producing fuzzy linguistic models of mineral processing equipment directly from engineering data. These fuzzy linguistic models rely exclusively on data collected from the processing systems being modeled and do not presuppose an understanding of the physics of the system. The fuzzy linguistic models use descriptive rules and explicit membership functions that provide a precise, nonmathematical description of the processing equipment. A genetic algorithm is employed to simultaneously select rules and tune membership functions used in the fuzzy models. The result is an extremely flexible approach to modelling that is applicable in a variety of linear and nonlinear systems. The effectiveness of this approach to modelling is demonstrated using a four-input, two-output model of a grinding circuit.

Jan 1, 1996

By J. J. DeMull, B. A. Boster

Amax's Sleeper mine uses conventional cyanidation milling and heap leaching techniques to produce gold. Since milling operations commenced in March 1986, average ore processing rates have improved from the design rate of 455 t/d (500 stpd) to more than 720 t/d (795 stpd). Heap leaching was added to the process facilities in September 1986 at a design rate of 1.5 kt/d (1650 stpd) and current heap leaching rates exceed 2.7 kt/d (2950 stpd). Presented are descriptions of the Sleeper processing facilities with emphasis on the crushing and grinding circuits, a review of the selection of crushing and grinding equipment, and a summary of operating performance during the first 16 months of operations.

Jan 1, 1990