Search Documents

By H. T. Clark, S. Feigenbaum

THE importance of measuring the temperature of molten steel in the open-hearth furnace has been recognized for many years. Poor temperature control may be costly to steelmaking operations and lead to a lowered quality of the steel. Low or excessive temperatures may shorten the life of the furnace, ladles and molds. Rates of reactions in the furnace and efficiencies of deoxidizers are known to change materially with a change in the temperature of the metal and slag. Ladle skulls and mold and stool stickers cause steel to be scrapped instead of being converted into useful products. Finally, the structure, segregation and surface condition of ingots are affected by the teeming temperature. Mill investigations of the effect of bath temperature upon steelmaking operations have been largely qualitative in character, based upon observations by practical melting men. The physical chemist has used the empirical information available and has reached reasonable and useful conclusions with respect to the various melting processes. The introduction of a reliable direct- reading pyrometer will permit accurate quantitative evaluation of the effects of temperature and should furnish a more rational basis for study of the thermo- chemistry of steelmaking. The problem is not merely one of making a small number of temperature measurements in the open-hearth furnace. This has been done by several methods to a degree of precision that was apparently satisfactory. Considerable effort by a number of investigators has been directed rather to the development of an open- hearth bath pyrometer that would be both accurate and practical for routine measurements. To be practical, the pyrometer should be inexpensive to operate; that is, the installation, operating and maintenance costs should be exceeded by the tangible benefits to the open-hearth operator. Temperatures from 2800° to 3100°F. are encountered in the open-hearth furnace. The surface of the molten metal is covered by several inches of slag, which prevents direct observation of the metal surface for optical or radiation measurements. Both slag and metal are highly reactive at these temperatures and will attack to a greater or lesser extent any material immersed in them. Adequate protection of thermocouples, which of necessity must be brought to the temperature of the bath, has generally resulted in a large, heavy assembly made up of .brittle materials, unsuited for handling on the open-hearth floor. The lie of the equipment was short and maintenance was an important consideration. EARLIER WORK Any one of a number of physical proper- ties of liquid steel could conceivably be used as a basis for temperature measurement. Efforts to the present time, however, have been confined largely to measuring either the thermal electromotive force generated between two dissimilar materials immersed in the steel or the intensity of radiation from the surface of the steel. These

Jan 1, 1946

By S. D. Bechtel

Bechtel Civil and Minerals, Inc., one of the Bechtel group of companies, is a large engineering and construction firm that services the mining industry, among others. The firm's head, S. D. Bechtel Jr., comments on how his E&C company is dealing with the recessionary economy. First, he offered a historical perspective. About a half century ago-in the middle of the Great Depression-W. A. Bechtel and several business partners drew up a fixed price bid to build the Hoover Dam. At that moment in history, the W. A. Bechtel Co. was a modest success, but the times were troubled and uncertain. Money was scarce and a lot of contractors across the country were one project ahead of bankruptcy. The bid for Hoover was a make-or-break proposition for Bechtel, and it turned out successfully. The Hoover Dam was a no-frills operation in an isolated and harsh environment. There was plenty of hard work, long hours, and not many amenities. Controlling costs was critical. Everyone knew what had to be done, and why and what the consequences were. Today's Challenge Bechtel is now a bigger, more complex organization whose management views the current economic recession as a challenge to be met in much the same way W. A. Bechtel met the challenge of the Hoover Dam: by pulling together with a sense of purpose and direction. In many respects, Bechtel's situation today has a number of parallels to that which faced my grandfather. The company is eminently successful, but times are tough and there are plenty of signs that they could get tougher. My grandfather bet on the Hoover Dam to insure the future health of his company and I think we can work together again in that same tradition, make some tough decisions together, and the company's future can be just as promising. The first and most important requirement is to make certain that everyone understands the situation. The Bechtel group of companies are in an excellent financial position now. Its workload hit an alltime high in 1982 and it is well positioned in its principal markets. But the next two years may be critical for the company. Traditionally, Bechtel's work load lags behind general developments in the economy. Although many of its clients continue to suffer serious business difficulties, Bechtel is only beginning to feel the impact. The worldwide market for basic metals remains soft; relatively low prices and abundant supplies of oil and gas have flattened the petroleum market and made once promising synfuels projects economically unattractive; utility clients are still caught in the vise between overregulation and escalating costs. And persistently high, long-term interest rates have made capital investments expensive and difficult to justify. The company maintained a healthy workload through 1982. In some areas it has had little new work and consequently has been forced to lay off some staff as projects have been canceled or concluded. In other areas new work has tided the company over and more people have been hired. But new work bookings have fallen off, creating some uncertainty for the near future. 1983 requirements are clear, although seemingly contradictory. Belt tightening and cost reduction are necessary for Bechtel to remain healthy and competitive, enabling it to handle a possible further downturn with a minimum of turmoil and dislocation. At the same time, we need to allocate resources and funds in areas that will keep us positioned for the turn-around marketplace.

Jan 2, 1983

By W. W. West

MACHINERY used for size reduction of materials may be divided into three classes-depending upon the manner in which the crushing force is applied. In the first class could be listed the primary crushing units, such as the jaw crusher and gyratory crusher-which crush to coarse sizes by applying pressure intermittently between converging surfaces. In the second class may be listed crushing units, such as the hammer mill, roller mill, and ball mill, which crush principally by grinding or attrition. In the third class is the impact mill which, as the name infers, crushes by impact. The second and third classes generally include machinery used as secondary units for intermediate or fine crushing and grinding. Theory of Crushing by Impact Throw a stone into the air and give it a severe blow while it is momentarily suspended, and it shatters into several pieces. The impact crusher uses this "batting" principle, but carries it one step further. As the material to be reduced enters the crushing chamber, it receives a severe free-air impact blow by hard-hitting beaters suspended from rotor discs. The shattered particles formed are then driven at high velocity against impact blocks, where a further reduction in particle size takes place. The rebounding particles from the impact blocks are again caught by the beaters, and the process repeated until the material is swept out of the open bottom of the crusher. Impact Crushing Versus Attrition Crushing Fig. 1 shows a Hammermill type of attrition crusher. This particular mill has central feed and is reversible. Because of the central feed, an impact section can be designed into it at the feed entrance for preliminary crushing, followed by the cage bar attrition area for final sizing. The material is caught and held in a crushing chamber enclosed by grate bars or perforated plate. It remains in this chamber until it is reduced to particle size small enough to pass through the openings between the bars or in the plate. In this manner the top particle size discharged from the mill is closely controlled. As the swinging hammers pass through the bed of material, the material is broken down by a scrubbing action between hammers and material, material and grate bars, and material against material. This attrition produces a rounded particle shape, accompanied by slivers and a comparatively high percentage of fines. The crusher is especially useful in industries where the material treated is not too abrasive, such as limestone, cement or coal plants. It can be readily understood that from the maintenance standpoint, it is not suitable for hard abrasive materials such as refractories and aluminum oxides. One common type of impactor is shown in Fig. 2. The bottom of this type crusher is entirely open and the passage of the material through the crushing chamber is almost instantaneous. Liberal clearances are maintained between the impact hammers and the anvil type breaker blocks. This eliminates practically all attrition. It is the elimination of attrition that makes the impactor particularly adaptable for reducing hard, abrasive materials. The impactor is also well suited for the reduction of wet or frozen materials, which clog an ordinary Hammermill. Particles broken by impact, when examined under the microscope, show a distinct tendency toward rough, cubical shape, with a minimum of fines. Another important factor in impact crushing is that crushing is accomplished along natural cleavage lines, thus freeing foreign ores or materials.

Jan 1, 1952

By G. Vibert Douglas

IN a previous paper by Douglas and Gillies (1), a simple field test was given for gold. Later work by the present writers, and by others who have kindly written to us, shows that the test is not as satisfactory as it was hoped. In many cases, the gold mirror is completely obscured by a dense precipitate which, up to the present, it has been found impossible to remove. After many attempts, we have temporarily given up the iodine test and have been working on a simple pyridine reaction based on the work of Putnam, Roberts, and Selchow (2): The ore to be tested is ground to a fine flour. Place half a gram of this powdered ore (an amount that will cover a Canadian ten-cent piece, not heaped) in a six-inch test-tube and add 5 c.c. of aqua regia. The aqua regia. should be made up on each occasion, using four parts of hydrochloric acid and one part of nitric acid, both concentrated. Shake the solution in the test-tube for about one minute and allow to settle until dear. The rime to settle may be 30 to 60 minutes. When dear, a drop of the solution is with-drawn with a fine, dean eye-dropper or capillary tube and placed on à small glass plate. A slide such as is used for mounting rock sections is suitable. Now place an equal sized drop of pyridine solution on the plate beside that of the aqua regia solution to be tested. The pyridine solution, containing nine volumes of hydrogen bromide to one volume of pyridine, can be made up in advance and carried in a glass-stoppered bottle. Join the two drops with a glass thread or fine, dean stick, and allow the merged drops to stand undisturbed. I t is well to place the slide on a piece of white paper so that the presence of the crystals which may form can be easily seen. The time for their formation will vary with the amount of gold present, but the slide should be allowed to stand for at least 30 minutes before negative results are reported. A hand lens of at !east ten magnifications is essential. If gold is present, minute red crystals will form around the margin of the drops as these drops slowly evaporate.

Jan 1, 1938

By John T. MacWaters, George H. Milly

INTRODUCTION This paper describes operational procedures and instrumentation which were developed to implement a patented method of detecting and locating uranium ore bodies. All equipment was designed for accurate and reliable use under difficult field conditions. Data resulting from these developments, some of which are incorporated in a companion paper for this conference*, have contributed to our understanding, of the nature and significance of naturally-occurring radon exposures. Further applications of these techniques may prove useful in studying anthropogenic radon in evaluating the significance of variability in radon flux, or in taking proper account of the contribution of natural radon to ambient radon concentrations, particularly in mineralized regions. OPERATIONAL PROCEDURES The uranium search technique employed by GEOMET begins with a [reconnaissance mode], which utilizes a series of ambient air filter samples taken from a moving or standing vehicle to detect anamalous concentrations of radon. These samples are normally taken at night under stable (temperature inversion) or neutral atmospheric conditions, to avoid the rapid dispersion of the radon clouds typical of daytime turbulent conditions. Radon daughters formed by the decay of radon quickly attach to ambient aerosol particles and are captured on the surface of a membrane filter during a five-minute sampling period. The filter is placed in a portable alpha scintillation counter, and a five-minute count is started at a preset time after the completion of the sampling period. This count is followed immediately by a second five-minute count to enable determination of the cloud age, based on consideration of the relative half-lives of the initial radon daughters. With the use of tables computed from the mathematics of the uranium decay process, and with the measured radon background accounted for, the first and second counts are used to estimate the time which has elapsed since the pure radon initially emanated from the earth's surface. This cloud age, combined with wind speed and direction measurements made at the beginning and end of each sample, as well as with an understanding of the effects of local terrain features on wind trajectory, provides an estimate of the Probable location of the source. In practice the reconnaissance mode involves one vehicle with a single operator to take the five-minute samples, moving or standing, along any available roads or trails in the area to be covered. Under the usual nighttime stable conditions the cool air flows downslope and downvalley, and the operator will pay special attention to locations along the axes and confluences of the natural downflow patterns. These facilitate sampling of large air drainage areas. Successful detection of sources of radon based on high concentrations of radon daughters, and substantiated by evidence of "fresh" clouds, are frequently made on the basis of a relatively few samples taken judiciously by an experienced operator during a reconnaissance. At this point he has a choice: he can continue to cover the designated reconnaissance area, leaving the localization of any anomalous radon detections to await the ranking of detections by priority, or he can continue with localization of the detected source, either alone or by radioing for another vehicle to assist in triangulation operations. Localization of a source involves skillful and experienced use of the continuously collected data on concentration, age, and wind speed and direction, together with knowledge of the terrain from observation and contour maps, and exploitation of the available roads. Since age ratios are dependent solely on proximity of the source and wind speed, decreasing [cloud ages] based on statistically significant increasing age ratios represent the most useful. information in localization. The [magnitude of the concentration] of radon daughter products is also useful; however, it may vary widely for a variety of reasons during sampling for a localization, thus making this a secondary parameter for localization. Large values of concentration are of course useful; typical results for successful detection of a strong anomaly would yield alpha counts ranging from 10 to 25 times background values. These counts are convertible to ambient radon concentrations by appropriate consideration of the decay process. Successful localizations of radon sources using this procedure with ambient atmospheric measurements normally will narrow a source location to within an area ranging in size from less than a quarter of a square mile to at most a square mile, and frequently give information on the probable shape of the source (in plan view) on the earth's surface. Judicious use of this procedure could undoubtedly provide finer localization, but the coarser results just described are adequate for this Phase of GEOMET's uranium exploration procedures.

Jan 1, 1981

By Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Samuel Nowak, Khaled Mohamed, Morgan Sears

Coal ribs present a major safety hazard in underground mines, and there is currently no unified approach for their design in the United States. To tackle this issue, this study investigated the stability of underground coal pillar ribs under development load. Utilizing over a thousand 3DEC models, a framework for calculating coal pillar rib rating (CPRR) was developed. A detailed step-by-step method was outlined for computing the CPRR based on a 3DEC analysis, which was then validated with various 3DEC models, demonstrating a strong correlation between the two models. The results demonstrated that the rib factor of safety (RibFOS) under development load is directly proportional to CPRR, coal mine roof rating (CMRR), and floor strength, and inversely proportional to the overburden depth and rib height. Moreover, a regression equation was formulated to predict the RibFOS based on the aforementioned parameters. Furthermore, empirical relationships were developed between the RibFOS and the applied primary rib support density (PRSD) in U.S. coal mines. To ease the calculations, a stand-alone application, Design of Rib Support (DORS), was developed. This application can be used to assess rib stability and easily calculate CPRR, RibFOS, and PRSD.

Jul 1, 2023

By Carl Lee

WITH the modern trend toward motor drive in coal mines, more careful forethought should be given to future layouts than has usually been done in the past. Both top and bottom equipment of future new mines is likely to differ radically from those of a decade ago. No one is able to predict very far ahead, but provisions can be made to allow for uncertainty. One thing stands out: the mine of the future will be laid out for long life compared to that of the small mine of the past, where an inexpensive top plant, simple equipment, a small timbered shaft, small cars, light rail, hand loading and mule haulage all contributed to a short economical life.

Jan 1, 1933

By Ken Criley, Marc E. Orman

Identifying the optimum ultimate height for heap leaching ore requires the consideration of a number of competing factors. A primary limitation is the reduction in the permeability of the ore with increasing heap heights. At low permeabilities the heap can blind off, cause serious ponding and runoff, and become very difficult to rinse at closure. The authors present a laboratory methodology that has been successfully used on several projects to identify the maximum height for controlling heap permeability.

Jan 1, 1996

Mr. Address Member is hereby proposed by the undersigned, as a Associate Junior Member of the American Institute of Mining Engineers. Signatures of three Members or Associates. Place of birth Year of-birth Education, when, where and how acquired, with degrees, if any. A technical education is not requisite for membership. Dates Please give record of experience on following page with dates; for e. ample, in the form used by "Who's Who In America" and similar publications.

Jan 6, 1917

Mr. Address Member is hereby proposed by the undersigned, as a Associate Junior Member of the American Institute of Mining Engineers. Signatures of three Members or Associates. Place of birth Year of birth Education, when, where and how acquired, with degrees, if any. A technical education is not requisite for membership. Dates Please give record of experience on following page with dates; for example, in the form used by "Who's Who In America" and similar publications.

Jan 11, 1917

Mr. Address Member is hereby proposed by the undersigned, as a Associate Junior Member of the American Institute of Mining Engineers. Signature of three Members or Associates (not Junior Members). Place of birth Year of birth Education, when, where and how acquired, with degrees, if any. A technical education is not requisite for membership. Dates Please give record of experience on following page with dates; for example, in the form used by "Who's Who In America" and similar publications.

Jan 1, 1918

Mr. Address Member is hereby proposed by the undersigned, as a Associate Junior Member of the American Institute of Mining Engineers. Signature of three Members. or Associates (not Junior Members). Place of birth Year of birth . Education, when, where and how acquired, with degrees, if any. A technical education is not requisite for membership. Dates Please give record of experience on following page with dates; for example, in the form used by ?Who's Who In America" and similar publications.

Jan 3, 1918

Mr. Address Member is hereby proposed by the undersigned, as a Associate Junior Member of the American Institute of Mining Engineers. Signature of three Members or Associates (not Junior Members). Place of birth Year of birth Education, when, where and how acquired, with degrees, if any. A technical education is not requisite for membership. Dates. Please give record of experience on following page with dates; for example, in the form used by "Who's Who In America" and similar publications.

Jan 12, 1917

Mr. Address - Member is hereby proposed by 'the undersigned, as a Associate Junior Member of the American Institute of Mining Engineers. Signature of three Members or Associates (not Junior Members). Place of birth Year of birth Education, when, where and how acquired, with degrees, if any. A technical education is not requisite for membership. Dates . . Please give record of experience on following page with dates; for example, in the form used by "Who's Who In America" and similar publications.

Jan 2, 1918

By Woodcock J. T, Rummel P. H, Sparrow G. J, MacRae C. M

A rapid automated search method, developed for the location of native gold grains in polished sections with a scanning electron microscope (SEM), has been extended to locate platinum group elements (PGE), in particular platinum and palladium, and their minerals down to 1 ¦m in size. Problems associated with the search for PGE minerals are discussed and examples of PGE minerals located with the facility in drill core sections, crushed ores, and metallurgical test products are given.

Jan 1, 1991

By K Matsui, R N. Gupta, H Shimada

Roof falls and failures of powered supports were major threats at longwall face. Abnormal geological conditions were caused roof falls and shield damage. Therefore continuous monitoring and analysis of strata behaviour was imperative on real time for forecasting adverse behaviour. Novel PXI instrumentation system was successfully developed for continuous monitoring and analysis of supports pressure, leg closure and gate roads convergence. However, this paper briefly examines the novel gate roads convergence monitoring system with field applications.

Jan 1, 2003

By Timothy J. Orr, Michael J. Beus, Frank T. Duda

The technology to enhance safety and control features for mine shaft hoists is being investigated by researchers at the U.S. Bureau of Mines (USBM). The objective of the research is to prevent injuries and fatalities related to hoist and elevator operations. Monitoring and controlling mine hoisting operations will allow hoist operators, inspectors, and maintenance personnel to increase their awareness of potentially dangerous situations and provide controls for safer operations. Process simulation and visualization software, real-time data sensing, and advanced programming techniques are being applied to this problem. Development of reliable and cost-effective sensors and data acquisition interfaces to monitor hoist loads and detect slack rope conditions is underway. Three-dimensional design software was used to visualize mine hoisting to enhance understanding of hoist operations. Quick Basic and Visual Basic (an object-oriented Windows interface) are being used for acquiring and processing hoisting data. Testing and evaluation of components are underway at USBM testing facilities. The resulting system will allow hoist personnel to assess critical operating parameters, such as hoist position, speed, acceleration, conveyance load, and rope tension.

According to Vorwärts, the German Mining Commission sent to ascertain the damage done to the mines of France says that the work of restoring these mines will furnish work for all the unemployed in Germany for the next 8 years. The commission said the work of reconstruction would have to be clone from. "the ground up," especially in the Departments of Pas de Calias, Courriere, Lens, Lievin, Drocourt, Mourchin, Carvin, and Dourgas, where the destruction was pronounced "terrible." Most of the mines have been "drowned," and in rebuilding new shafts would have to be protected against the inward pressure of water. The Germans declared the work of restoration would not only be one of great difficulty, but that in many cases it was impossible to ascertain the extent of the damage clone to each mine. They also said it was not easy to fix responsibility for the destruction because it was done by nu-merous groups of troops and the records showing where each military unit was located and at what period were not complete or available.

Jan 12, 1919

By Ashwani Jain, D K. Soni

Compressive strength of rocks is often required by mining engineers and quarrying authorities for blasting operations. Uniaxial compressive strength of rocks can be predicted with reasonable accuracy with the help of point load strength tests which can be easily conducted at site by the field staff, simultaneously as the cores are recovered from drilling operations. A number of diametral point load tests and uniaxial compressive strength tests have been conducted on the specimens of different rock types under air dried, and saturated condition as well to study the effect of ground water saturation on strength. It has been observed that due to saturation uniaxial compressive strength and point load strength get reduced to a maximum of 32 and 29 per cent respectively. It has also been observed that uniaxial strength is sixteen times the point load strength in air dried as well as saturated condition. However, this factor used for calculating uniaxial compressive strength may be reduced to a lower value for the safety of miners in field blasting operations.

Jan 1, 1994

By Daniel Ruffing, Jeffrey Evans

Vertical cutoff, or barrier, walls are an integral part of environmental site remediation efforts. Vertical barriers are commonly deployed to limit the influx of clean ground water and/or to control the off-site migration of contaminated groundwater. The level of detailed design consideration devoted to the vertical cutoff wall component varies widely from project to project and generally decreases with decreasing size and complexity. For those projects receiving minimal design effort, conservative design decisions can lead to unnecessary costs or unanticipated conflicts between the various design considerations. In this paper, the authors discuss several important design and construction aspects of vertical cutoff walls requiring particularly careful consideration during the design phase of the project. These design and construction considerations include the need for and extent of excavation for a key, project target hydraulic conductivity, the use of statistical allowances in the specifications, filter press testing, sand content of in-trench slurry, cleaning of the backfill slope, measurement of stress and strain, the additional of slag in cement-bentonite cutoff walls, and longevity of cutoff walls.