Search Documents

Difficult ground conditions in the area planned for placement of vent rises to the surface at the Porgera Goldmine led engineers directing the project to chose blind shaft boring methods of shaft construction from the available alternatives. Zeni Drilling Pty Ltd was first contracted in 1988 to install a group of three closely-spaced, steel lined shafts. The success of these led to an order for a fourth hole in the same group followed by two more, less than a kilometre. away, under a separate contract in 1992. All of the shafts were completed on.schedule to within one day. The only significant difficulty arose during commencement of the last shaft when the strata collapsed trapping the drilling tools and jeopardising the stability of the surface collar pad. The situation was corrected by innovative lining techniques and the project went on to finish on schedule. This paper discusses the application of various technologies associated with the project including aspects of geotechnical input, drilling fluid chemistry, mining engineering and logistics.

Jan 1, 1993

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Variations of cut-and-fill stoping are the most com¬monly used methods for mining narrow, nearly vertical veins in the United States. These methods offer the best results for maximum recovery with minimum dilution of ore from veins that are irregular along either the strike or dip. The vein is developed along the strike length in 61 to 122-m (200 to 400-ft) blocks or stopes and vertical lifts of 48 to 61 m (160 to 200 ft). The level development is either on the vein or parallel to the vein with crosscuts intersecting the vein at right angles. Chutes, manways, and haulageways are established in the center of the stopes at the lower level of the ore block. Mining then proceeds by blasting down horizon¬tal cuts of the vein in both directions from the chutes. As the blasting continues to the outer limits of the stope, the broken ore is slushed into chutes. When a complete horizontal cut has been made, the service raise, including chutes, is raised to a height of a few feet from the back and the stope is filled with either sand fill or waste rock. Then the mining cycle is re¬peated until the stope reaches the level above. LEVEL DEVELOPMENT PRACTICES FOROVERHAND CUT-AND-FILL STOPING The two basic methods used are: the development of the haulage drift within the vein, or development of the haulage drift paralleling the vein in the foot or hang¬ing wall with crosscuts intersecting the vein perpendicu¬larly at 61 to 122-m (200 to 400-ft) intervals. The il¬lustrated methods of development show some of the variations which can be used to develop a stope block. Development for cut-and-fill stoping does not require the more elaborate schemes outlined for shrinkage or sublevel long-hole stoping. Many factors must be considered before deciding on a particular development plan and usually the nature of the vein or host rock will dictate which specific method to use. If the vein is relatively straight, then develop¬ment on the vein is feasible. Excessive ground pressures will necessitate the leaving of a sill pillar (Fig. la) and highly fractured or "heavy" ground will require timber¬ing (Fig. 1b). Development on the vein has the advan¬tage of reducing capital outlay and waste handling prob¬lems since the mined rock has value. But removal of the sill pillar is costly and time-consuming. Also, where no sill pillar is left, excessive timbering and subsequent level repair is a drawback. Development in either the footwall or hanging wall is the more common procedure and offers greater flexi¬bility in overall development of consecutive stoping blocks by partially disassociating the level development from stoping (Fig. 2). Chutes, manways, and service compartments com¬prise the next stage of development and are established in a variety of ways. They provide access to the stope, ventilation ducts, and muck removal. Several different development systems are in common use and average costs for each have been developed. Raise borers are used to establish ventilation and ac¬cess from level to level. They are normally reamed with 1.5 or 1.8-m (5 or 6-ft) cutterhead and may either be left bald or lined with a 1.2-m (4-ft) diam corrugated liner plate, depending upon ground conditions. The use of an Alimak raise climber is another effec¬tive method of driving a raise from level to level. The size usually is 2 m (7 ft) square. This will accommodate square-set timber which is later installed. This method of raising is not common, although it is a valuable tech¬nique especially when level spacing is several hundred feet.

Jan 1, 1982

By Claude A. Goode

Large quantities of high grade coal exist in thick seams in the United States. Many of these thick seams are too deep to be surface mined and do not lend themselves readily to underground extraction. To develop the new mining technology required to effectively mine thick seams, the Department of Energy has entered into a Cooperative Agreement with Mid- Continent Resources, Inc. to demonstrate the multilift longwall mining technique in a 28 foot-thick seam at their L.S. Wood No. 3 mine near Redatone, Colorado. The seam will be extracted in two lifts, with a 5-foot natural partition of coal left between the upper and lower lifts. Proper selection of face supports is critical to the success of this project. Specifications were defined for the roof supports, and it was concluded that the supports selected must provide full coverage, yield at the legs, and have a 60-inch push- out cantilever that can be set at any position under full load. A Hemscheidt two-leg shield was judged as the best qualified candidate and was selected for the multi-lift trial.

Jan 1, 1981

Book review AUSTRALIAN MINERAL INDUSTRY REVIEW FOR 1970 The Review is prepared by the Bureau of Mineral Resources, Geology and Geophysics, and gives an interesting and up-to-date account of the Australian minerals industry.

By J. F. Archibald

A research effort has been undertaken, under Workplace Safety and Insurance Board of Ontario (WSIB) sponsorship, to characterize the support capabilities of conventional and innovative spray-on lining materials for mitigating dynamic failure effects created by simulated rockbursts. Conventional spray support media, such as shotcrete and fibrecrete linings, and a variety of new spray-on lining materials [thin, spray-on liners (TSLs)], typically polymer-type thin coatings, were subjected to simulated rockburst influence. For baseline comparison, conventional rockbolt and bolt-and-mesh support products were also evaluated. Observation of lining performance was undertaken through completion of field-scale support and rock detonation trials. Controlled blasting tests were conducted at the Queen’s University Explosives Laboratory to examine the effectiveness of the variety of surface coating agents for modifying dynamic rock spalling processes. All tests were performed upon largely undisturbed and homogeneous rock materials in highly repeatable fashion. All blasts were observed seismically and photographically to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion and support liner survivability characteristics. These material comparison trials were performed to assess the relative effectiveness of a wide range of currently available area support techniques for suppressing hazards associated with dynamic rock ejection. The results of this study validate that thin, spray-on linings may be equally as effective, and often better, than conventional support materials at mitigating rockburst or like damage in highly stressed mine environments.

Jan 1, 2004

By K Osman, P Bennett

The mining of an underground orebody requires development both in waste and ore before stoping commences. Regardless of what metal is being extracted, the waste development is minimised to reduce the cost per unit of metal mined. At the Western Metals Zinc Kapok mine site, reducing the cost per tonne of lead and zinc mined is paramount. Decline waste development costs can be minimised by methods such as increased gradient or reduced drive size. Ore development will also involve some mining of waste. The degree to which waste mining can be minimised will depend on the thickness and dip of the orebody. The drive geometry will also determine the percentage of waste within the face. It is by mining methods such as resue mining that selective mining may be used to maximise the amount of metal mined and reduce waste dilution. Resue mining can be used around a set of selection criteria established by the mine site. These selection criteria will determine how resue mining can be applied to the mine site. Selection criteria include firing times, number of headings available, acceptance criteria for percentage lost metal, dilution and most importantly operator acceptance. The single pass or two pass resue mining method should be chosen depending on the site acceptance criteria and selection criteria. The Western Metals Zinc Kapok mine site has established a set of parameters which accept the two pass resue mining method for the mining of the ore drives. The blasting results from a single pass resue method were reviewed during more recent trials in a single heading. Through a comparison of results, the parameters allowed the decision to determine the applicability of resue mining and its current form to Kapok. This paper outlines the parameters set by the Kapok mine site, reviews these in relation to the two forms of resue mining and examines the criteria which make this mining method applicable for Western Metals Zinc.

Jan 1, 2002

By U Briem, R Verreet

The level of wire rope technology used in mine hoisting applications has a significant effect on the overall efficiency of the hoisting system. This paper discusses the effect that a reduction in rope mass per unit length and an increase in rope breaking strength can have on rock skip capacity and hence mine shaft output. A 20 per cent reduction in rope mass per metre for a typical 48 mm hoisting rope, while maintaining the breaking strength, increases the skipÆs capacity by circa 30 per cent at a suspended rope length of 3000 m. Such gains in shaft output, without any significant changes to the shaft or winder design, can have major implications for the feasibility of future deep mine projects. The technical challenge for rope manufacturers is how to get rid of 20 to 30 per cent of the rope mass while keeping the breaking strength and modulus of elasticity of the whole rope constant. CASAR are currently developing steel wire rope constructions where the steel IWRC has been replaced with high strength, high modulus fibres such as Kevlar«, Spectra« and Dyneema«. One of the key aspects of such composite rope designs is to ensure equal load sharing between the different rope components, ie in proportion to their area. If there is a significant difference in modulus between the fibre core and the steel outer strands, the core may not carry its proper proportion of the load and the outer strands would be overloaded. Some technical aspects of the design of composite steel wire ropes are discussed. A design and operational issue that needs careful consideration is the safe non destructive testing (NDT) of composite ropes. Traditional magnetic NDT would only be capable of inspecting the steel wires. Techniques therefore need to be developed that would give operators a reliable indication of the condition of the load bearing fibre core. This paper also discusses possible solutions to this very important NDT question.

Jan 1, 2005

By M. E. Stutt, R. H. Rehder

"The mining industry is taking advantage of the increased performance resulting from the use of variable speed A C drives for large motors. This technology provides increased efficiency under the variable speed and torque requirements of such drives as mine hoists, conveyors, and air moving equipment. The technology does introduce voltage spikes on the voltage wave form that stress the insulation system to a greater degree than would occur with a constant voltage source. These voltage spikes must be considered in the design of the insulation system used for these motors.BackgroundHistorically the insulation systems for large AC motors were designed to withstand with reasonable life the voltage stresses of a 60 Hz constant sinusoidal voltage. One of the design tests is a voltage endurance test that requires the application of a 60 Hz voltage from conductor to ground equal to four to five times normal and establishing a time to failure. These higher than normal voltages accelerate the normal aging process by causing extensive partial discharge activity (corona) within the insulation system and the time to failure is a relative indication of insulation life.In addition to the voltage endurance test at 60 Hz, the individual coils are subjected to a surge voltage test to establish the withstand capability of the turn to turn insulation under switching surge conditions. The surge voltage is a fast rise time, 0.2 microsecond to crest value, voltage spike that can be caused by a circuit breaker or contactor closing operation. These voltage spikes can have a crest value of greater than 3.5 times the normal line to ground crest voltage of the normal 60 Hz power supply. The standard withstand test value is thus 3.5 times normal line to ground voltage. Because the voltage surges or spikes occur mainly during start and stop switching conditions, voltage endurance under these conditions has not been a major factor in insulation system design."

Jan 1, 1995

By B, T Norgate, S Sanetsis, R Davidson

Global cement production accounts for about five per cent of man-made CO2 emissions (WBCSD, 2002). Such operating practices will increasingly be considered unsustainable, unless significant reductions in environmental impact can be realised by the industry.Slag is a high volume waste product from ironmaking, with about 300 kg of slag being produced per ton of iron. Critically, one ton of slag waste, if used as a replacement feedstock for Ordinary Portland cement (OPC), can prevent around one ton of emitted CO2 since no calcining is required. Slag cement blends can also show superior properties compared to OPC, such as lower heats of hydration and higher late strengths, but more development is needed to overcome their low early strengths. Rapid quenching of molten slag is required to produce æhydraulically-activeÆ binder when reacting with OPC; but water quenching can also require between five to ten tons of water per ton of slag at the plant. æDryÆ granulation (atomisation) is emerging as an alternative technology, the resulting solid product does not require drying, and possibilities exist for recovering heat energy from the hot slag.CSIRO Minerals has well-developed skills and equipment in pilot-scale pyrometallurgical treatment, and granulation of molten slag, including traditional wet, and also dry methods. Techno-economic desktop studies can also be used to help quantify factors such as value-adding of treated waste products, potential reductions in CO2 emissions and carbon credits, reductions in water consumption, and the possible decreased energy costs associated with fine grinding of dry slag granulate.The authors will present preliminary results from slag atomisation/dry granulation testwork (0.5 - 2.5 kg scale) and associated modelling studies, conducted using a æsyntheticÆ and industrial ironmaking slag. Outcomes from a techno-economic study on production of cement utilising wet or dry atomised slag granulate will also be discussed in detail.

Jan 1, 2004

By Julie Hampden, Tim Dardis, Per Reinhall

"Noise from impact pile driving can harm fish, marine mammals and other sensitive wildlife over large areas. Marine pile driving is highly regulated, and regulators require sound levels to be below certain thresholds to avoid harassment and injury to sensitive marine life. In many locations, timing restrictions, use of noise attenuation technologies and extensive monitoring for impacts to wildlife are also required. As a result, permitting can be laborious and time consuming, and project implementation and scheduling can be complicated. Underwater noise levels are measured with an underwater microphone (hydrophone), which converts noise pressure to voltage and is calibrated to express the noise pressure in Pascals (Pa). The pressure is often expressed using a logarithmic scale, in decibels (dB). Several specific metrics can be used to describe underwater noise. Three common metrics are the instantaneous peak sound pressure level (dBpeak), the root mean square pressure level (dBRMS) and the sound exposure level (dBSEL) referred to as the peak, RMS and SEL levels, respectively.During impact pile driving, the peak pressure represents the instantaneous maximum pressure, either overpressure or underpressure, observed during each pile strike. The RMS level is the square root of the mean of the square of the pressure during the duration of the impulse; it is the average pressure level of the pile strike from beginning to end. The cumulative SEL (SELcum) is calculated by summing the cumulative pressure squared and integrating over time of duration of the pile strike. SEL is used as an indication of the cumulative energy of a pile driving event, which may consist of one or many pile strikes.Regulatory agencies use these metrics to help characterize the noise pressure levels that can affect sensitive species. Some of the most frequently encountered biological thresholds in the Northwestern United States that are used by regulators to describe potential impacts to sensitive species are summarized in the following table. Agencies have defined thresholds for different types of injury, either hearing or bodily harm, and for temporary injury or disturbance."

Jan 1, 2017

By W. H. Geis

THE following pages summarize the causes that led to the suggestion of unit operation of the Paloma field, the organization of committees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan.

Jan 1, 1942

By C Reed

Titaniferous magnetite deposits are a significant source of vanadium for use in high strength steel alloying and other chemical applications. The mineralogy of the deposits varies markedly and the ore characteristics strongly influence the process route selected and the metallurgical outcomes. Characterisation of the ores reveals the presence of magnetite, ilmenite and other minerals such as spinel hematite and goethite with variable degrees of weathering along with weathered products of host rock. The standard processing route is to crush, grind and magnetically recover a concentrate for salt roasting to produce a soluble vanadate. Ore beneficiation is practised to generate an iron based mineral concentrate containing much of the vanadium with low silica levels of two per cent. Typical processing problems encountered are fine liberation size, over grinding of the magnetite and variable response to magnetic separation resulting from the weathering profile. Beneficiation options are restricted, and generally focused on producing a combined iron and titanium rich concentrate containing vanadium due to the fact that ilmenite and magnetite and their products of weathering are magnetic and have similar specific gravities making their separation difficult. The ilmenite usually contains low levels of vanadium making its separation highly desirable from the iron mineralisation containing higher levels of vanadium. Salt roasting of vanadium ores followed by water leaching has been the standard processing route for many years. The cost of suitable sodium salts, availability of capital and increasing energy costs and energy availability are critical factors in determining the viability of aspiring vanadium producers. To date, only Windimurra has acquired full capital funding, secured energy and sodium salt supplies at suitable cost that enable the construction of the project. Low overall recoveries of vanadium to concentrate roasting at up to 1200¦C are critical cost issues. In this paper, factors influencing the recovery of vanadium are reviewed and emerging processing trends explored. The important features of the processing of titaniferous magnetites have been condensed from the literature, published works, company websites, our own work and personal communication.

Jan 1, 2008

By John Ratti

Building on Canadian Capabilities for Space Resource Missions: Space resource science and technology mission building blocks Canadian historical perspective Status and future pursuits It takes Canadian Teamwork to succeed in space exploration! Space resource science and technology building blocks: Orbiting / Delivery Elements Spacecraft Sensors Landed elements Roving / Mobility, Autonomy Sample acquisition and handling Sensors, GN&C Science Operations Partnerships: Government ? Industry Between Industry With Academia and Scientists

May 1, 2013

By Hua-Zhong Yu

Gold is one of the most widely used substrate materials for self-assembly. Self-assembled monolayers (SAMs) prepared from alkanethiols and their derivatives on gold are the most reliable and well-studied systems to date, which have attracted much attention because of interest in two-dimensional molecular assemblies, and of their potential applications in molecular devices, sensors, and functionalized interfaces. Gold electrodes are also very important in microelectronics and electroanalytical chemistry. This work reports the characterization of a new type of gold substrates for self-assembly. The gold substrates are constructed from recordable compact disks (R-CDs) with simple and straightforward wet-chemical treatment, and can be made at desired sizes and shapes that satisfy different experimental needs. In particular, an easy, inexpensive, and reproducible method to prepare self-assembled monolayers (SAMs) on CD-R gold substrates after removing the protective polymer films with concentrated nitric acid was described.

Oct 1, 2003

By D Jeffery, R Whittering, G Lane

Most aspects of process design are best addressed via bench scale or pilot plant scale test work. However, as experience is gained, fundamental or indicative data can provide more than adequate information to manage the risk associated with some process aspects of concentrator design.Historical precedence exists where minimal design test work has resulted in successful projects. On many occasions benchmarking, sometimes supported by fundamental data such as mineralogy, has been used to successfully develop effective process plant outcomes. Of course, this style of approach is most common with æfast trackÆ projects and often comes with the usual surprises that result from inadequate geometallurgy to define the project cash flow.This paper explores the risks and opportunities associated with the various facets of process development and design for a base metals concentrator. The paper is intended to provide guidance to project managers rather than address the technical aspects of process engineering.CITATION:Lane, G, Whittering, R and Jeffery, D, 2012. Benchmarking versus test work - How should you manage process risk?, in Proceedings Project Evaluation 2012 , pp 49-52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By Ian Sheppard, Kugan Kuganathan

The Mount Isa Rocky Paste Fill (RPF) was one of the five fill options investigated for the Enterprise Mine filling between June 1996 and September 1996. Co-disposal of deslimed cemented tailings (CHF) and suitably graded rockfill (RF) in certain ratios produced the rocky paste fill. The RPF behaved like a cohesive paste with very high proportion of rockfill in the mix. Several large-scale mixing trials and drop tests proved that the rocky pastefill results in a homogeneous fill mass after placement. Segregation of RF was a common problem with MIM's traditional cemented rock fill (CRF), which is a combination of CHF and RF. The segregation was eliminated and a non-segregating paste like fill was created by optimising the particle size distribution of RF, and combining the RF and the CHF in optimum ratios. In rocky pastefill, the excess water in the cemented deslimed tailings slurry is taken up by the rockfill as the surface moisture on the rockfill particles and also as pore water between the particles. This results in thickening of the CHF, and the resultant mix is a non-segregating cohesive paste, which can easily spread to any horizontal distance inside a stope at a very low surface angle. The rocky pastefill releases no free water and relatively more pervious than the standard CHF due to rockfill component. With an average cement addition of 1.5 to 2% the rocky pastefill can develop higher strengths over 1Mpa. The rocky paste fill is applicable in many situations and can accommodate a variety of coarser materials that would be available in different mine sites. This paper present the research work and the experience associated with the rocky paste fill, and gives clear design principles for any potential users.

Jan 1, 2001

By C. R. Tinsley

Valuations can be molded, twisted and misinterpreted. Cases of spurious scope setting; limits to the information or access by the valuer; difficulties with the lack of comparative valuations; inappropriate valuation methods and outright speculations are described. None should be accepted by an experienced, independent minerals valuer. The Australasian Institute of Mining and Metallurgy (TheAusIMM) is working on a Valmin Code for which a Manual of Best Practice and Valuation Guidelines may be developed.

Jan 1, 1995

By V. M. Shick

For practical purposes of the use of information resources in the field of geomechanics and mine surveying with accepted mining technology in mines, the authors have developed the packaged software programs of the survey-geomechanical information system with database objects of mine field. This system enables to execute the graphical representation of workings layout in preset scale, axonometric projection, the zones of higher ground pressure: program packages for calculations of rock pressure manifestations and for selection of suitable support facilities for the permanent, development and active workings and vertical shafts based on the information resources of the State Research Institute of Mining Geomechanics & Mine Surveying (VNIMI). The program packages are applied at coal mines in Russia and in Kazakhstan. The profitable operation of coal mines can be reached only by the combined optimal engineering decisions in mine working's laying-out and their reliability and safety at the stages of their designing and exploitation, and with minimal harm of the environment as well. This problem is being complicated by the fact that today the mining-practicing engineers and designers are ordinarily facing the problem " of an information barrier", when the complexity of controlling systems exceeds the potentialities of traditional management of production practice. Coal mine is a typical representative of complicated systems, because the information about geological structure, physicomechanical properties and stress-strain state of rock mass are of fragmentary character and insufficiently reliable. A mine has a developed network of interrelated workings, by the way, some of them are productive ones being subjected to control to a certain extent, and some of them are abandoned ones being noncontrollable and hazardous in rushes of water, gas, pulp and fire. The ground pressure forces cause the disintegration of rock mass growing with depth. The progress of mining operations constantly changes the geomechanical situation forming the zones of bearing pressure, stress relieving, coal falling, as well as it leads to the pulp movement on the earth surface, breaks the ground water flow, causes deformations and changes in stability of buildings, constructions and natural objects on the earth surface. One should take into account the existence of hazardous zones within the mine field, i.e. the zones of elevated ground pressure, geological dislocations and those ones under natural water reservoirs, ponds, etc. Major coal seams are prone to rock bursts, sudden outbursts, bleeding, endogenic fire. It is obvious, that in practice it is extremely difficult to account for the mentioned above factors in their interrelation.

Jan 1, 1996

By C. Bergstrand

"Precipitation of gypsum and the formation of scale may pose a serious challenge in the leaching of several minerals. As an example, precipitated gypsum may form scale in the machines increasing the need for maintenance. Alternatively, it may encapsulate precious elements, i.e. gold and lower the recovery during subsequent leach processes. In this work we explore how different biopolymers modify the rheology of gypsum at three different pH levels at ambient and elevated temperatures. The ability to disperse gypsum vary with temperature, pH and biopolymer. It is also inversely related to the scaling potential. Measurements of the zeta potential as a function of increasing amounts of biopolymer reveals that the magnitude of the zeta potential changes in the presence of biopolymer, and so does the ability to disperse the gypsum suspension. Similar results with hematite will also be discussed. The methodology and results may aid in the selection of additives used in mineral processing applications where scale pose a problem.INTRODUCTION Processing of refractory gold ores normally involve either atmospheric or oxidation under pressure in order to convert sulfides to oxides (Weir, King, & Robinson, 1986; Weir, Robinson, & King, 1986). This conversion facilitates leaching of gold (and silver) in normal CIL processes. During oxidation, sulfides are converted to sulfates. Normally, there is an abundance of calcium ions in the process water, either released from the ore or added as lime to adjust pH for the CIL process. Precipitation of calcium sulfate, or other compounds (calcium carbonate, jarosite, hematite) is a way to remove gangue minerals from the solution entering the CIL circuit (Ji, King, Fleming, & Ferron, 2010). Precipitation may also cause challenges in the process as gold (or other valuable elements) may become encapsulated in gangue. (Beauchamp, Choung, & Xu, 2006). In addition to precipitation, the precipitated gangue minerals may solidify and form scale in the processing equipment. Recently, Lauten and Kluck (2016) found that dispersants used as scale inhibitors to prevent encapsulation of gypsum did not modify the solubility of gypsum. In the utilised model system, similar amounts of gypsum precipitated with and without dispersants. Instead, it was found that the dispersants evaluated as scale inhibitors reduced the yield stress of gypsum suspensions. The reduced yield stress was associated with a reduced tendency for gypsum particles to agglomerate and form scale."

Jan 1, 2017

By John Dasher

The impetus given to mineral dressing arid chemical engineering by the war has placed many persons without previous experience in positions where they are concerned with the size of solid materials they are testing. Many good textbooks cover this field in considerable detail but are more concerned with the "why" than with the "how" For beginners and those to whom size is not of primary concern, this brief circular has been prepared. Refer-

Jan 1, 1942