Search Documents

By I. Ngoma, Marijke Fagan, Susan Harrison, Rebecca Chiume

"Heap bioleaching is an unsaturated hydrometallurgical extraction process which is commonly applied to the recovery of copper from low grade sulfide ores as well as for preparatory treatment of gold ores. The leaching reactions occur in the liquid phase, catalysed by iron and/or sulfur oxidising micro-organisms. Contact of the mineral grains with the leaching solution is consequently essential for metal recovery. Additionally, the liquid is responsible for the transport of the liberated metal out of the heap under gravitation-driven flow. However, the highly inhomogeneous structure of the heaps coupled with low irrigation rates cause the flow to vary between being gravitationally and capillary dominated, resulting in non-uniform wetting of the ore. In this study a 132 kg agglomerated ore ‘slice’ is used to examine the effect of liquid distribution on microbial colonisation and mineral recovery in a long term bioleach (> 500 days) when irrigation from a single drip emitter source is employed. The novel setup enabled sample collection from ports positioned along the length and height of the ore bed, so that 2D maps of the degree of wetting and microbial colonisation could be generated at different times in the leach. Lateral movement of the liquid increased with bed depth; the majority of flow was below the irrigation point while the top corner of the bed that was not irrigated remained the driest region of the heap throughout the experiment duration. The lowest cell numbers were also recorded in the driest regions. Specifically, cell numbers in the top corner of the bed, 400mm from the irrigation point, remained at undetectable levels until the 283rd day measurement, in line with typical heap operation durations. This indicates that slow colonisation of the heap in the regions between irrigation points may be a significant issue in heap optimisation."

Jan 1, 2014

By H. Somekawa

The fracture toughness and deformation structures an AZ31 magnesium alloy processed by equal-channel-angular extrusion (ECAE) were investigated. The average grain sizes of as-ECAE and annealed-ECAE alloys were 4.0 and 16.3 µm, respectively. The plane-strain fracture toughness, Kip, in as-ECAE and annealed-ECAE were estimated to be 27.3 and 23.5 MPam1/2, respectively, by stretched zone analysis. The fracture toughness indicated higher value with grain refinement. From optical microstructural observations in samples after fracture toughness tests, although deformation twins were observed in annealed-ECAE, no deformation twins were observed in as-ECAE. From TEM observations, the dislocations on basal and non-basal planes were activated in as-ECAE. With grain refinement, the activations of dislocations on both basal and non-basal planes were possibly related to the reduction in formation of deformation twins in as-ECAE. In addition, in comparison with direct extruded process, ECAE process was more effective method to improve the fracture toughness in magnesium alloys.

Jan 1, 2006

By Mark Spence, Tom Lardner, Matthew Janes

"IntroductionThe design-build method streamlines project delivery through a single contract between the Contract manager and the design-build team. The design-build method places emphasis on collaborative project management between design and construction disciplines to minimize project schedule, reduce costs, encourage balance risk amongst the design-build team. Since 1985, the percentage of nonresidential design and construction projects has increased from 5% to 45%.1A project carried out in Edmonton, Alberta, Canada will be used as an example to illustrate the challenges of the design-build project delivery method and the merits of establishing a GBR. The project involved a complex slope stabilization as part of an extensive freeway widening. At the project location the roadway was being widened within the base of a historic stream valley into a steep slope with a history of a previous slope failure. The slope was to be steepened through the installation of a series of 14 interlocking arc structures constructed half way up the slope. Access and schedule proved critical to the successful completion of the project.Geotechnique and Site HistoryThe geotechnical investigation undertaken for the site included six boreholes drilled at the crest of the slope to depths ranging from 14.5 m to 30.2 m. Laboratory testing of the soil samples included direct shear tests, Atterberg limits and grain size analysis. The geotechnical report also referenced a previous geotechnical investigation that was carried out in response to a failure of the slope in 1971."

Jan 1, 2015

By M. B. Sizgoric

Quantitative mineralogy is used in a study done on an Inco Metals Company nickel sulfide occurrence from 'the Thompson area in Northern Manitoba. The study included: a) determination of the variations in chemical composition of the ore minerals; b) determination of the liberation of the ore minerals for the various types of ore and for different feed grinds; c) assessment of the preliminary mill test results by comparing the mineral distribution in the different tailings. Preliminary mill test results had outlined three main problem areas: 1) unacceptabiy low grade concentrate with, 2) very high weight recovery and, 3) low pyrrhotite rejection resulting in a high sulfur concentrate. The mineralogical study readily explained these results by showing that: 1) between 20 and 40% of the nickel in the feeds and 55 and 75% of the nickel lost in the tailings is associated with pyrrhotite. This accounts in part for the low grade of the concentrates obtained at high recoveries: 2) hexagonal nonmagnetic pyrrhotite constitutes over 90 percent of pyrrhotite. Since hexagonal pyrrhotite floats more readily than monoclinic pyrrhotite, this could be part of the reason for the undesirable high pyrrhotite recoveries into the concentrates. Further test work to establish both the optimal grind and the best conditions for pyrrhotite rejection is therefore mandatory.

Jan 1, 1981

By R. W. Amstutz

Abstract. The shaft was drilled on U.S. Government land in the Piceance Creek Basin and was funded by the U.S. Bureau of Mines. It was drilled to 723 meters (2 371') to provide access to rich deposits of oil shale, nahcolite and dawsonite for geotechnical test work and environmental mining research. Rotary drilling and dual string, reverse-air, jet-assist circulation methods were used. Drilling required 8 months. Site preparation, running and cementing the casing required another 4 months. A 2.44-meter (96-inch) ID steel welded casing, 5.1 cm (2 inches) thick was installed and 2 700 tonnes (63 000 sacks) of cement were slurried and pumped into the annulus.

Jan 1, 1980

By R. B. Massy-Greene

Project engineering and development is a process of optimisation of capital, operating and financial costs, and extraction rates in the light of current and forecast economic conditions for the sale of the product. The aim of the process is to maximize financial returns to the sponsors (project owners) within many often conflicting constraints. Thus, the sponsor's engineering and financial staff have a common goal, with performance measured in financial terms. Consequently, each group must be aware of, and responsive to, the constraints imposed upon the other. For financial staff, the increasing size and complexity, and escalating capital costs of new ventures have required them to seek finance in larger amounts, and by non-traditional methods. In addition, senior management are requiring indications of the availability of finance as a pre-requisite to a decision to commence project development activities.

Jan 1, 1982

By Guy Demers

"This paper defines the responsibilities and functions of the Maintenance Department, and its organization, physical and human assets, highlighting the unique operating problems. Due to the self-sufficient aspect of the Asbestos Hill Deception Bay project, the Maintenance Department cover-s fields that are numerous and very dissimilar: production, mobile, processing, service, power generation, fire protection, heating, water and sewage disposal equipment. Added to this, buildings, plant and camps, wharves and communications equipment all demand versatility, adaptability and expertise from maintenance personnel. Good maintenance practices are a necessity in this environment and are more critical than at southern locations; that is, high-quality replacement material, complete and well-controlled preventive maintenance, major repairs on a component-replacement basis, updated inventory, efficient training and permanent contacts with suppliers, combined with an equipment improvement program, updated specifications on lubricants, hoses, seals, filters, etc., are mandatory. The seasonal aspect of the operations applies a great deal of pressure on the maintenance team, as the production months do not permit major repairs. Short- and medium range planning and accurate evaluation of equipment conditions highly influence production efficiency. Maintenance control, planning and scheduling do not follow the accepted standard routines, as personnel turnover normally does not permit an accumulation of knowledge of the equipment history and condition by the •individual tradesman."

Jan 1, 1976

By M J. Davies, R S. Davies

Despite increased expenditure, the global discovery rate of world-class ore deposits has been in decline for over a decade (Schodde, 2017). Mineral exploration has traditionally followed an empirical approach, searching for evidence of mineralisation upon the surface of the planet, then drilling to define the extent of an ore body beneath the surface. As outcropping deposits in well-defined areas are depleted, there is a need for exploration to extend to less well-explored search spaces. One popular new frontier is exploration at greater depths beneath the Earth's surface. However, exploring for deep deposits with limited surficial evidence requires the implementation of predictive targeting methodologies (Hronsky, 2011; McCuaig & Hronsky, 2014). The Mineral Systems Concept (Hronsky & Groves, 2008; McCuaig et al., 2010) provides a framework for predictive exploration targeting. Ore deposit formation is recognised to be a focused mineralising event. These events represent self-organising critical systems and are underpinned by the interaction of complex, non-linear processes. Through the collection and analysis of datasets that map mineralising processes, it may be possible to predict the size and location of resultant ore bodies. CITATION: Davies, M J and Davies, R S, 2018. Beyond below-ground geological complexity: Developing adaptive expertise in exploration decision-making, in Proceedings Complex Orebodies Conference 2018, pp 95–98 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Doyle A. Ellerbruch

An FM-CW microwave system was investigated for measuring coal layer thickness. Measurements were made in three different mines near Pittsburgh, Pennsylvania, near Fairview, West Virginia, and near Coffeen, Illinois. Microwave frequencies in the range 1-2 GHz were used to measure samples up to 55 cm thick. All samples were backed with a naturally occurring shale. Measurements were also made on coal and shale samples compounded in the laboratory at the Bureau of Mines Pittsburgh Mining and Safety Research Center near Bruceton, Pennsylvania. The results indicate that layer thickness can be determined in most cases, although large anomalies may, in some cases, produce misleading results. Many anomalies that were detected with the FM-CW system were verified visually by drilling into the coal layer. The dielectric constant of coal apparently varies significantly within a coal seam. The form of the output signals from the FM-CW system seem to simplify the data interpretation and analysis process as compared to the manually swept microwave system used previously. It appears that this technique has the potential of measuring changes in the dielectric constant of a coal seam and providing an output that can be used for real-time corrections in layer thickness; measurement.

Jan 1, 1976

By G. M. Gay, R. L. Perrine

This paper describes a method of numerical computation for three-dimensional, unstable, miscible displacement behavior useful for heterogeneous systems, as well as for more ideal conditions. In the method, flow equations are first linearized by a perturbation approach. The basic flow process is separated and a solution for its behavior readily obtained. The remaining problem of deviations from the basic flow caused by non-ideal conditions is then subjected to numerical analysis. Results obtained from use of the method are also presented. Although conditions assumed in the test cal-culations were severe, results show the type of dispersing flow expected and appear quite satisfactory. The method has eliminated or reduced in importance problems of oscillating values near steep fronts, excessive computer smoothing, etc. A unique advantage of the method is that the source of variations from ideal behavior can be observed. ,The one serious drawback results from the algebraic complexity of the perturbation approach, and the need for second-order terms to be retained in calculations of interest. Fewer array points are available and more computer time is required than would be desired. However, these difficulties are also experienced with other approaches to the solution of three-dimensional dispIacement problems. INTRODUCTION Prediction of behavior of the miscible displacement process within a porous medium for any system of engineering importance is plagued by a number of difficulties. With typical fluid properties the displacing fluid has the lower viscosity, and there is a natural tendency toward flow instability. The problem of predicting instability is compounded by the fact that every real system is heterogeneous. Permeability will vary from point to point — not entirely systematically, and yet not in a random fashion leading to a readily defined average. Furthermore, permeability is unlikely to be isotropic. These permeability properties, which are characteristic of any real porous medium, accentuate the effects of flow instability. Another factor to be considered is that flow dispersion accompanies the displacement process in a porous medium. Mechanistically, dispersion is due to the fact that flow between any two points in the medium follows multiple tortuous paths, each characterized by slightly different flow properties. The fact that the coefficient characterizing dispersive properties of the real medium JS a tensor with variable elements complicates matters. Further difficulties arise because the parabolic influence, while not negligible, is small. Thus, there is a tendency toward steep and uneven displacement fronts along which dispersion smoothing must be represented accurately. Yet frequently used numerical analysis schemes may tend toward either instability, oscillation or excessive smoothing, none of which gives the desired accurate picture of flow behavior. Thus, while many experimental and analytical studies of the process have been made, predictions of actual performance are still subject to considerable uncertainty and possible improvement. This paper reports on part of a study which attempts to develop improved methods for solution of the flow equations describing the miscible displacement process. Of necessity, the calculations were performed on a large digital computer. A three-dimensional system is represented, and the coefficients defining dispersion and permeability can be varied in a manner representative of a real system. Because the differential equations are nonlinear, a first step is to linearize them using a perturbation approach. Objective of this approach has been to separate the basic flow which would occur in an ideal system and for which predictions are readily made. Then the numerical analysis, which is necessarily complex, is directed toward solution of the perturbation equations. These equations state how the basic flow is modified

Jan 1, 1967

By Danqing Gao, Brijes Mishra

Spatial variance of rock properties is an important characteristic of rock which addresses the heterogeneity of mechanical and physical properties and their effect on underground mining. Assessing spatial variance can be useful for both locating potential difficult grounds and performing reliability analysis in the mining support system. This study shows a microscale numerical model for rock material based on continuum mechanics. To consider the spatial correlation factor of mechanical properties in realistic rock mass, this study introduces a spatial correlation concept into the traditional type III extreme value distribution model. Based on the improved microscale random model, we conducted a series of numerical uniaxial compressive tests and one longwall mine model to investigate the progressive failure of rock. The results show that spatial correlation factor can significantly affect the load-deformation curves and fracture patterns. The spatial variance model was applied to a longwall mine that included several cutting sequences to observe the influence of the spatial variance on roof behavior. The cohesion and friction random fields induced failure that propagated randomly through the immediate roof in different entries. The results showed that the spatial variance provides an accurate prediction of erratic roof falls in coal mines.

Jul 20, 2020

By F. S. Niu

With the feature of finely-dissemination particle and complex mineral composition, oolitic hematite is considered to be the ore dressing difficult problem in the world. Series research on refractory oolitic hematite in Zhangjiakou Area are introduced as following: ore properties?technology mineralogy and mineral processing technology. The survey shows: with the fine grinding of the hematite to a fineness of -0.076mm 95%, obtaining iron concentrates grading 62.74% Fe at the recovery of 46.80% by high intensity magnetic separation- reverse flotation flowsheet; under the three stages intensity magnetic separation,four stages grinding and four stages gravity separation, getting the iron concentrates grading 61.09% Fe at the recovery of 45% using high intensity magnetic separation- gravity separation flowsheet; with roasting temperature of 800°C, time for 75~90min and ore-coal ratio of 11, gaining the iron concentrates assaying 62.74% Fe at the recovery of 87% by roasting- magnetic separation flowsheet. At present, this research is still doing for the target of raising the concentration recovery on the base of high grade concentrate. It is in the hope of fully utilizing the existing hematite resources in Zhangjiakou

Jan 1, 2014

By B. W. Madsen

Experimental results obtained from large scale (7 tons), long-term (500 days) leaching of low tenor copper sulfide ores were interpreted by a geometric model involving the movement of a reaction zone through the ore fragments. The postulated leaching mechanism involved mixed kinetics and included diffusion of the reacting species through the host rock and a chemical reaction at the surface of the mineral particles. Ore properties which were considered were ore particle size and shape, grade of ore, and mineral content. Excellent agreement between the mixed kinetic model and the laboratory leaching results was obtained when minus ½ inch ore particles were not included in the leach. Also, a satisfactory prediction of copper recovery from plus ½ inch ore with a different particle size distribution was made; however, it was necessary to modify the shape factor in the model. Predictions of copper recovery from an ore sample which included the minus ½ -inch fine fraction and leaching for 460 days was 56.5 percent, and the recovery from leaching was 47.0 percent. The presence of fines caused channeling and uneven solution distribution and inhibited the leaching rate.

Jan 1, 1974

The global mining industry will always face significant challenges. Some, though, are bigger than others. What do you consider the major challenges facing the mining industry as a whole and SME in particular? Without a doubt, the major issue in both coal and metal/nonmetal mining industries is the ?graying? of the workforce in all aspects of mining. As the baby boomers continue to age, valuable experience is being lost by industry, government and academia. And there is the potential for SME to lose some of its membership. Now with that said, I should note that, despite the aging of the workforce, SME membership continued to grow by 7.1 percent during 2011.

Jan 1, 2012

By Irwan Halim, Bhoshaga Mitrran Ravi Chandran, Kevin Huynh

Tunnel segmental lining design constitutes a significant iterative process where modeling and numerical analysis are factors in deciding the number of segments, their dimensions, gasket placements, as well as the locations of dowels and bolts. Consequently, these modifications lead to revisions in the final drawing details. However, the current tunnel engineering practices lack systematic solutions that effectively bridge the gap between the iterative design process and efficient visualization of completed drawings due to the time- consuming nature of redrawing. This paper presents a pioneering application of AI-driven solutions including using Autodesk's API, for the Northside Interceptor Tunnel (NSIT) Project. It showcases the automation of drawing design and the real-time visualization of modifications, thereby streamlining the drawing process.

Jun 23, 2024

By W. E. STOKES

COMPANIES operating airplanes have had a relatively prosperous year, permitting them gradually to re- place old types of equipment. The pre-eminence of American-made planes, engines, and accessories has been challenged, either by foreign designs or by domestic patterns that have, for one reason or another. been licensed for manufacture abroad.

Jan 1, 1938

By R. L. Dietrich

Magnesium alloy sheet has less ability to accept bending at room temperature than most of the heavier metals. In work designed to improve the bend properties, the preferred orientation of the sheet is of major importance as it is in all studies of the properties of wrought magnesium products. When rolled into sheet, all of the common magnesium alloys form an orientation texture having the basal (002) planes approaching parallel to the surface of the sheet. This texture is only slightly affected by annealing. Magnesium single crystals are highly anisotropic, and, as might be expected, so are magnesium alloy wrought products in which a strong preferred orientation is developed. It is therefore not surprising that bend properties are affected by orientation. Ansel and Betterton1 reported that the orientation of AZ3lXt sheet varies from surface to center and that bend properties are improved by etching away the sharply oriented material at the surface of the sheet to reach the more broadly oriented structure below. This paper covers a study of that orientation, either during the rolling process or by treatment of the finished sheet, in an effort to improve the bend properties and toughness of sheet. Literature The orientation texture of magnesium and magnesium alloy sheet has been studied extensively. Early determinations2 showed that pure magnesium sheet has a preferred orientation in which the basal planes are parallel to the sheet surface within very narrow limits. J. C. hIcDonald3 and J. D. Hanawalt4 reported that sheet containing a small amount of calcium develops a "double" texture, that is, the majority of the basal planes are a few degrees from parallel to the surface and there is a noticeable vacancy at the parallel position. Bakarian5 made careful quantitative pole figures of both pure magnesium sheet and MI alloy SEPTEMBER 1949 sheet which show these features. In all of these studies, however, the orientation was determined by transmission methods in which the resulting pattern is an average through the thickness of the sheet. The tendency of wrought metal to exhibit a different orientation at the surface from that in the center has been reported by many investigators. G. von Vargha and G. Wasserman6 found that with copper, aluminum, iron, and brass the textures of rolled compared to drawn wires were the same at the center but differed markedly at the surface. It was also reported by investigators7 that the orientation of rolled aluminum varies from surface to center. Har-greaves8 found that the surface texture of AM503 (magnesium alloy similar to MI) sheet was different from the center texture. It is reported by Edmunds and Fuller9 that zinc alloy sheet sometimes had a thin layer at the surface with a strong orientation of the basal planes parallel to the surface, which, if present, impaired the bend properties of the sheet. Part1 Surface Orientation ofMag- nesium Alloy Sheet and the Effect on Properties Attempts to correlate the bend properties of magnesium alloy sheet with tension ductility over short gauge lengths proved unsuccessful and the subsequent investigation showed that nonuniformity in orientation is a con- tributing factor as the properties of the surface material have a much more important effect in bending than in tension. A program to study the relationship between surface orientation at the surface and bend properties was then undertaken. First, the effect of etching away the surface of sheet on the bend properties and the orientations at the various depths were studied. Sheet samples of M1, AZ31X, and AZ61X were etched in dilute nitric acid to remove the surface material for various depths to 0.015 in. As may be seen in Table 1, the minimum bend radius improved considerably as the surface layers were etched away but it was necessary to etch the sheet quite deeply, much more so than was found necessary by Edmunds and Fuller9 on zinc sheet. It is also apparent that the amount of etching required is a function of the sheet thickness. In all of this work, radii were measured as R/t, the radius divided by the sheet thickness, in order to eliminate the effect of the reduction in sheet thickness produced by the etching. To determine the orientation texture of the sheet, X ray reflection patterns were taken using copper radiation with the bearn striking the specimen at an angle of 17' to the surface, which is the Bragg angle for the (002) planes of magnesium. Two exposures were made of each specimen, one with the beam perpendicular to the rolling direction and the other with the beam parallel to the rolling direction. The symmetry of the preferred orientation in magnesium sheet is such that these two photographs gave an approximation of the pole figure sufficiently accurate for qualitative work and it was not thought worthwhile to make complete pole figures. These X ray patterns show that the orientation has a much narrower spread at the original surface of the sheet than below the surface. The narrow spread is found in sheet having the majority of the basal planes (002) parallel to the surface, and since this is an unfavorable position for slip, it is

Jan 1, 1950

By Phillip J. Maddex

After the presentation of a co-authored paper, "The Cost of Transporting Ores and Raw Materials in World Markets", at the February SME meeting, one questioner commented, "You have been talking about the large shipper and ship loads. What does the small shipper do?" This paper will attempt to answer that question, at least in part. Probably the questioner hoped to hear about specific new tools and new techniques that he could apply. But one paper could only scratch the surface of the vast fund of information available; so rather than talk specifics we should take basics, that is, people, management and technology.

Jan 1, 1967

By Charles H. Osmond

The rapid progress of basic changes in refining processes, which has characterized this division of the petroleum industry during the last 7 years, slowed up in 1926 and the industry as a whole devoted itself to the enormous task of adopting these changes to its methods of manufacturing. If for no other reason, the year of 1926 will stand out as the first year of widespread activities in placing refining on a true manufacturing basis. A brief survey of each of the important operations and the trend of the changes with their economic results indicate the importance of this period of transition. No attempt has been made to detail the numerous activities in each of the major operations and the writer would refer those seeking such information to the various trade papers and the paper on "Basic Changes in Refining Processes," by Walter Miller.' Distillation.—-Distillation (excluding cracking) is the major item in refining. During the past year there has been a wide application of the improvements developed in former years. Operating costs have been reduced for fuel, labor and capital items. Practically all types of distillations are now carried on as semi-continuous or continuous operations, rather than by the old batch method. Heat-saving devices, such as heat exchangers, or improved combustion chambers, have had a marked effect on the total fuel bill of the industry. The modern pipe-still has been widely used and figures available show that approximately 10 per cent. of the older shell equipment was replaced by pipe-stills during 1926. The range of usefulness of this type of equipment has been extended successfully to the most complicated types of lubricating oil manufacture. These stills afford marked economies in fuel as well as labor costs, also many advantages in older plants where space is limited, as a single pipe-still can replace several batteries of shell stills. Capital expenditure per barrel capacity is decidedly lower and offers economy in this direction. Although there has been considerable discussion of other types of distillation equipment such as the vacuum still, there has been no appreciable increase in these installations during 1926. Cracking.—-Cracking equipment increased rapidly during 1926 as evidenced by the increase in output of cracked gasoline from an average

Jan 1, 1927

Computer software has been developed to link real-time information generated by underground mine ventilation airflow monitoring sensors into a network simulation program to undertake network simulations and allow interpretation of key system data and operational changes. Results were used in the development of a computerised monitoring and simulation system to provide immediate or real-time data on air behaviour within each branch of an underground mine ventilation network through linking of sensors to the ventilation network simulation software. The outcome of the project is an online system that can report changes in the mine ventilation system, allow causes of changes to be isolated and rectified, improve balancing of available air throughout the mine, allow improved approaches to regulator setting and dispense with much of the labour used for underground ventilation measurement. The work activities in both coal and metalliferous Australian mines have involved examination and modelling of regulators, software modification and considerable mine site testing and optimising activities. There is some discussion on approaches to control of flow through ventilation systems with increased information. New systems will be part of a total mine information management system. They will have to be cost effective and justified by gains in productivity. New systems will need to provide simulation of contaminant production such as diesels, vehicle heat, strata heat, radiation, blast fumes and other gases. More robust real-time ventilation simulation systems will be required. Personnel and vehicle identification and production tracking will be collected to provide integrated ventilation system monitoring and control. This paper examines a study to gain greater understanding of computerised real-time airflow monitoring and control within the mine production system to provide immediate simulated information in each branch of an underground ventilation network and to allow interpretation of key system data and operational changes. A case study implementing a real-time airflow monitoring and control is discussed. Approaches to control of flow through ventilation systems with increased information are discussed. The concept of a system that can be linked to or be part of a total mine information management system is developed. Such a system can form the base for mine automation that allows mines to incrementally and cost effectively implement monitoring and control to further seek gains in productivity.

Jan 1, 2005