Search Documents

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

One of the most difficult challenges in underground mining is to forecast significant seismic events prior to their occurrence in order to support the safety of miners and to minimize damage to the underground operation. Passive seismic tomography is a tool to image the seismic velocity changes in a rockmass, which can potentially reveal the rockmass behavior before and after a significant seismic event. In this paper, the changes in seismic velocity of the rockmass before and after three major seismic events are investigated to determine whether there are identifiable precursory velocity changes associated with the major seismic events. Conventional mechanics imply that the induced stress at the hypocenter would continue increasing until failure, in the form of an induced seismic event, occurs. With passive seismic tomography we can image changes to the seismic wave velocity distribution within a rockmass and hence infer the changes to the induced stress near the hypocenter. This paper evaluates the hypothesis that induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs. In addition to analyzing p-wave velocity changes near the hypocenter, changes to the p-wave velocity at “zone centers” were also analyzed. These “zone centers” are regions within the rockmass that consistently have a p-wave velocity that is much higher than the average p-wave velocity for the rockmass. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring, however the p-wave velocity did increase in the closest “zone center” for two of the three events.

Oct 12, 2020

By Jay W. Hawkins

Under an approved remining program, mine operators can remine abandoned coal mines without assuming legal responsibility for treatment of the previously degraded water, as long as the discharging waters are not further degraded and other regulatory requirements are satisfied. A U.S. Bureau of Mines review of 105 remining permits in Pennsylvania indicates that remining results in substantial reclamation of abandoned mine lands, utilization of significant quantities of coal, and reduction of contaminant loads (acidity and iron) from degraded mine drainage discharges. Normality tests performed on the water quality and flow data indicate generally nonnormal distributions and extreme right-skewness, tending toward lower values. The water quality of underground coal mines was observed to be more highly degraded in terms of acidity, iron, and sulfate than that of surface coal mines. The optimum baseline sampling scenario is 12 months in duration at a frequency of one sample per month. Analysis of water quality and flow rates before and after remining indicates that a majority of the mines exhibited either no change or a significant decrease in pollution rate because of remining. The discharge flow rate was the dominant controlling factor when the post-remining contaminant load was significantly better or worse than the baseline (pre-remining) load.

Jan 1, 2010

By Richard Klimpel

The laboratory ball mill grinding of coal/water slurries is described for three coals. Emphasis is placed on the measurement of specific rates of breakage for various operating conditions. Corresponding rheological information is also presented based on data collected using a rotational viscometer. A rheological explanation of the influence of various slurry fluidity conditions on the specific rates of breakage is presented. This rheological approach has proved useful In both the identification of suitable chemicals for increasing breakage rates in coal/mineral slurry grinding and in the plant scale implementation of dense slurry grinding systems.

Jan 1, 1982

By J Nixon

I have to say that my story is not too much different to many others who grew up and worked in the great mining fields like Broken Hill, Mt Isa, Rosebery, Kalgoorlie or Kambalda and any one of them could have stood up here and spun you a good yarn.What does my paper offer you in this volume? By sharing my experiences I want to encourage you to consider your own experience with leadership, taking on change, learning from and contributing to the development of others.I have been very fortunate to be part of many new innovations into underground mining over the past 40 or so years; most of it with Conzinc Rio Tinto Australia (CRA)/Rio Tinto operations.•From hand-held drills and a homemade single boom Jumbo mounted on an old Airtrak, to the sophisticated twin boom jumbos with high speed drifters all controlled by an on-board computer;•from a Scraper winch and a Wagner 2D loader to fully automated electric LHDs that navigate to the tipple, empty the bucket and return to where they come from;•from hand-held cut-and-fill and timber stoping in Broken Hill to the bulk mining methods of a block cave where at Northparkes we mined more ore in a month than we mined in the total five years of operations at Currawang;•from hand-held scaling and bolting with no skin protection to installing ground support with Jumbos and sophisticated Cable Bolters and the introduction of in cycle shotcrete;•from hand-held ladder rising and shaft sinking to Box Hole rigs, Raise Bore Machines and Blind Hole shaft sinking; and•from Gelignite based AN60 stick explosives, ANFO, fuse firing and half second detonators to Powergel, Emulsions and electronic computer programmed detonators that can somehow be initiated by ‘Blast Ped’ travelling through the rock.

Mar 21, 2011

By A. Lam

The use of a liquid fed direct methanol fuel cell (DMFC) as a power source for micro and small portable applications is attractive due to its system simplicity, low temperature, etc. The aqueous methanol is directly oxidized and does not require additional fuel processing steps as in reformate based PEM fuel cells. In addition, the use of a liquid fuel is advantageous with respect to humidification, stack cooling and system energy density. The DMFC however, has technological issues that must be addressed before it can be widely adopted, particularly in larger applications such as small utility and transportation. At present, the crossover of methanol from the anode to the cathode is a major limitation on DMFC performance and fuel utilization efficiency. In this paper we discuss the influence of fuel modification on the control of crossover. This involves the use of different fuel additives and concentrations to minimize crossover. This appears to be the first reported case of the use of fuel modification (additives) to reduce methanol crossover. The rate of methanol permeation under passive conditions is discussed with respect to the different conditions.

Jan 1, 2005

By C. Carrasco

Caletones Smelter, Division El Teniente of Codelco Chile, has used Teniente Converter (TC) as the only smelting unit since November 2000. The modernization project considered the shutdown of the last reverberatory furnace, the installation of the fourth Teniente Slag Cleaning Furnace, the installation of a new fluidized bed dryer and the modification of the concentrate injection system into TC. The modernization project and related investments allowed for the increase of the smelting capacity up to 1.25 million t of concentrate annually.Next stage of the smelter expansion in the year 2004 considered the increase of the smelting capacity up to 1.44 million t/year. The expansion required technology modernization and the installation of the new equipment, such as concentrate injection system, oxygen plant, fluidized bed dryer and storage bin. Currently the annual smelting capacity is about 1.35 million t of copper concentrate, being limited by sulphuric acid plant treatment capacity. This paper presents the technology and production evolution in the Caletones Smelter in the years 2000 - 2006, demonstrating the potential of development and competitiveness of Teniente Converter as world-wide recognized smelting/converting reactor.

Jan 1, 2007

Energy is central to respond to critical stakes on human and industrial development requirements as well as on climate change. The increase of the share of carbon-free energy sources in the global supply mix will help to reduce significantly greenhouse gas emissions (GHG) as power generation accounts currently for 41 per cent of these emissions from the energy sector. In this energetic mix, nuclear and renewable energies are complementary, the first more focused in the baseload power generation whilst the second is well suited for decentralised power generation. In this context, AREVA's goal is to enable everyone to have access to a cleaner, safer and more economical energy. Regarding nuclear energy, AREVA's strategy is to capitalise on its integrated operation model, which groups together fuel cycle and nuclear power plant construction, aiming at building one third of the new nuclear capacities and securing the fuel cycle supply chain for its existing and future customers. Therefore, the front end of the uranium fuel cycle, from mining to the fabrication of fuel assemblies, has a key role in the sustainability of the nuclear industry. The replacement of the current capacity and the entrance of new countries on the nuclear power generation might lead to a significant rise of uranium demand by 2020. In order to be prepared in time, AREVA defined an ambitious industrial program to expand mineral reserves, increase the production of uranium concentrates, replace the conversion capacity, build two new uranium enrichment plants, one in France and one in the United States and upgrade its fuel manufacturing plants. To support the front-end industrial activities in the short and long term, AREVA invests on a portfolio of R&D projects to find out solutions to meet customers' needs, to improve its competitiveness and to develop new concepts and solutions to anticipate future market evolutions. In particular, some important technological challenges in mining must be surmounted to develop cost-effective methods to explore and exploit low grade deposits while creating sustainable solutions for reducing reagent, water and energy consumptions. In this lecture, an overview of the industrial investments of AREVA in the front end of the uranium fuel cycle and some highlights on its R&D major axis will be presented. This is an abstract only. No full paper was prepared for this abstract.  

Sep 13, 2010

By M. Albertson

The purposes of this statement are to define a problem that exists in regard to the estimation of developed petroleum reserves, to analyze the problem in an abstract manner, and to discuss it as an introduction to certain papers that follow. The problem is to devise and develop a suitable procedure to permit more accurate estimates of developed petroleum reserves. Part of the problem is to make such estimates available earlier in the life of any particular pool. The problem of securing more accurate estimates of developed petroleum reserves existed prior to curtailment of production. With curtailment, however, the problem became acute, some of the more prominent reasons being as follows: 1. The standard method of estimation depended on production-decline curves. This method is inapplicable while curtailment prevails and available methods arc insufficient. 2. The retarding influence imposed by wide open flow conditions upon overdevelopment is absent. Great losses of capital by overdevelopment can now occur before realization of the true situation occurs, or before effective steps can be taken to stop such wastage. This increases the need for early, accurate estimates. 3. Above-ground stocks have diminished and the equivalent of such supply tends more and more to be retained underground in the natural reservoirs. It becomes increasingly necessary to know accurately the amount of these stocks. To direct attention to an additional point of different nature: improved accuracy of reserve estimation can be obtained only by closer scrutiny of the factors that determine recovery. This examination and the resulting efforts to measure the effect of these factors in terms of ultimate recovery must tend to improve ultimate recovery. The statements regarding the acute nature of the problem also indicate to some extent the importance of the problem and the necessity of finding a solution. Developed reserves of the industry, and of individual opera-tors, are one of the great factors that properly should determine explora-

Jan 1, 1936

By M. Albertson

The purposes of this statement are to define a problem that exists in regard to the estimation of developed petroleum reserves, to analyze the problem in an abstract manner, and to discuss it as an introduction to certain papers that follow. The problem is to devise and develop a suitable procedure to permit more accurate estimates of developed petroleum reserves. Part of the problem is to make such estimates available earlier in the life of any particular pool. The problem of securing more accurate estimates of developed petroleum reserves existed prior to curtailment of production. With curtailment, however, the problem became acute, some of the more prominent reasons being as follows: 1. The standard method of estimation depended on production-decline curves. This method is inapplicable while curtailment prevails and available methods arc insufficient. 2. The retarding influence imposed by wide open flow conditions upon overdevelopment is absent. Great losses of capital by overdevelopment can now occur before realization of the true situation occurs, or before effective steps can be taken to stop such wastage. This increases the need for early, accurate estimates. 3. Above-ground stocks have diminished and the equivalent of such supply tends more and more to be retained underground in the natural reservoirs. It becomes increasingly necessary to know accurately the amount of these stocks. To direct attention to an additional point of different nature: improved accuracy of reserve estimation can be obtained only by closer scrutiny of the factors that determine recovery. This examination and the resulting efforts to measure the effect of these factors in terms of ultimate recovery must tend to improve ultimate recovery. The statements regarding the acute nature of the problem also indicate to some extent the importance of the problem and the necessity of finding a solution. Developed reserves of the industry, and of individual opera-tors, are one of the great factors that properly should determine explora-

Jan 1, 1936

By C. H. Loux

This paper deals primarily with the advantages realized from the adoption of methods more suitable than those previously used. The improvements noted include: (1) modification of practice in shrinkage stoping, (2) use of sublevel caving over grizzlies, (3) improved haulage and loading, (4) use of contract wages wherever possible. The Washington mine is on Jonestown Hill, one mile south of Oxford, in northwestern New Jersey. It is producing 16,000 tons of concentrates a month, which are being shipped to the Alan Wood Steel Company's furnaces at Swedeland, Pennsylvania. History The first settlement in this region is reported to have been in 1735, and the magnetite ores were recognized immediately. The first furnace, built in 1741, began operation in 1743. During the Revolutionary War the output was chiefly used for making cannon balls, which, owing to the sympathies of the community, without doubt found their way into the hands of the British. This old furnace is still standing. Several important veins were soon developed, including the Martin, Strayley, McKinley, Adelaide, Welsh and Lanning. Mining was carried to a depth corresponding to the capacity of the pumps available. When these became inadequate, the workings were abandoned, and another vein was opened up. The Washington vein was probably discovered about 1850, and the first shaft started in 1854. In 1879, William H. Scranton made the first complete magnetic survey of the district and serious exploration of the deposit was begun. Rather indifferent success attended the earlier efforts of the many companies that attempted to mine and smelt the ore. In 1929 the property was leased by the Warren Foundry and Pipe Co. to the present operators, and the modification of practice then inaugurated is described in this paper. Geology These veins, like most eastern deposits of magnetite, are formed from, or are contemporaneous with, pegmatite intrusions into a gneissic country rock. The ore therefore follows the banded structure of the gneiss,

Jan 1, 1934

By Olav Dalen

A HUNDRED years have passed since Wöhler made the first few particles of aluminum by decompos-ing aluminum chloride with potassium. In 1854 Deville used sodium to decompose the double chloride of aluminum and sodium, but even various subsequent improvements of the process, especially by Castner, did not sufficiently decrease the cost of the metal to bring it into general use. In 1862 Monckton proposed to reduce Al O? with carbon by the aid of the electric current, but the efforts of the Cowles brothers to do so were not successful and in 1884 they turned to making aluminum alloys by electrolysis. At about the same time Hall in America and Heroult in France success-fully worked out the technology of dissolving A12O3 in fused cryolite and electrolyzing the bath. It is hard to realize that forty years ago the annual production of aluminum was only 30 to 40 tons per year and the price of the metal thirty times what it is today. Great strides in decreasing the cost of production, improving the quality of the metal, and increasing the output have been made in the lifetime of middle-aged men. The large consumption of electrical energy in the form of direct current makes it necessary to locate aluminum-producing plants near waterfalls, to avoid transmission losses. Norway with its abundant water-falls is therefore a logical place for the development of aluminum production, even though it is necessary to import the bauxite, which is the raw material of the process. It was foreigners who first started the aluminum in-dustry of Norway and the first two plants were built by the British Aluminium Co. in 1906 to 1908; one at Vigeland near Kristiansand, and the other at Stavan-gerfjord in Nordfjord. These two plants are still oper-ating and producing over 3000 tons a year. When the plant at Vigeland is enlarged the production of the company will be more than 4000 tons a year.

Jan 11, 1927

By James D. Sisler

Among the various studies made by the Coal Fact Finding Commission, appointed by President Warren G. Harding in 1922 to investigate all phases of the coal-mining industry in the United States and to report to Congress, was one concerning the amount and nature of losses in mining bituminous coal in the eastern part of the United States. This study was carried on under the direction of the U. S. Bureau of Mines. The writer was appointed field engineer to investigate the problem in Ohio, Pennsylvania and West Virginia. Some 400 mines were studied in these three states and conclusions were drawn from many sources of data. The summary report written by George S. Rice and J. W. Paul states that "the field reports indicate that the recovery in Ohio will remain about as at present, except in the Belmont district; whereas in Pennsylvania it will gradually improve, and in West Virginia it will improve rapidly." Since 1922, the writer has been interested in gathering material to substantiate or contradict these prophecies. Nature of Coal Losses There are six general causes of losses of coal in mining: (1) coal left on the roof and bottom; (2) coal lost in room, entry and panel pillars; (3) coal lost in oil-well or gas-well pillars; (4) coal lost under buildings, railroads and boundaries; (5) coal lost in handling and prepayation, underground and surface; (6) coal lost by rolls, thin or dirty areas and under streams. Local economic aspects that dominate the type of mining conditions determine to some extent whether certain losses are avoidable or unavoidable. In general, however, unavoidable losses include coal lost in the protection of buildings, streams, railroads, restricted properties and around oil and gas wells. Barrier pillars and other safety pillars are unavoidable losses as long as their size does not exceed the minimum for adequate safety. Natural physical conditions beyond human control, such as rock faults, clay veins, partings and binders, bad top and bottom, rolls and horsebacks, cause unavoidable losses. Unavoidable losses

Jan 1, 1931

By John P. Harmon

This paper was written with two objects in view: (1) To describe in detail what has been done toward the ventilation of the main unit of the Portovelo mines and the results; (2) to give information that may be useful to anyone who may have to make a preliminary mine ventilation survey, with recommendations for the improvement of the existing system and finally the maintenance of the improved system. General Description The mining operations of the South American Development Co. at Portovelo, Province of El oro, Ecuador, are described here only briefly, as a full discussion does not fall within the scope of this paper. The orebodies are of the steeply dipping, gold quartz vein type, averaging about 2.0 meters wide. As shown in Fig. 1, the ore chutes are relatively far apart, making considerable development work necessary before connecting raises can be driven between the levels. Faulting' on a large scale and a parallel vein system have made long dead-end drifts and many crosscuts necessary in the exploration of veins. The ventilation of these dead ends is described under Auxiliary Ventilation. The method of mining2 is the filled rill stope method, similar to the method that is largely employed at the Butte mines. The main shaft of the mine is in the Amarillo Valley, on either side of which mountains rise abruptly to a height of several hundred feet above the collar of the shaft. Entrance is made to the mine: (1) Through the American shaft, which extends vertically from the surface to a depth of 1100 ft., of which only the first 700 ft. are in active use at the present time; (2) levels are driven from the American shaft at intervals of 30 m. (100 ft.), of which only the third, fifth and seventh levels need be considered in the ventilation problem; (3) adits at intervals of 30 m. (100 ft.), with a few exceptions, above the collar of the American shaft.

Jan 1, 1931

By Alexander L. Holley

THE Pernot system of rotating and withdrawing the hearth of a Siemens regenerative gas furnace for the production of Martin or open-hearth steel, is, perhaps, the most conspicuous of the several improvements which have lately been made in the steel manufacture. These several improvements in the open-hearth plant are not combined in any existing works, but most of them will be combined in not less than three works now erecting in the United States; and it seems probable that their joint result will not only reduce the cost of products of ordinary grades to Bessemer rates, but that it will produce new and better grades of products. The open-hearth steel furnace and its operation are so generally understood that but a few words of general description are necessary. The ordinary furnace is not unlike the common reverberatory puddling furnace, except that an intense, uniform, and controllable temperature is maintained by the Siemens gas regenerative system. The materials. employed are various : melted or unmelted pig with ore, and with or without scrap; pig iron purified from silicon and phosphorus, with or without scrap; pig iron and scrap, melted together in a cupola, or charged hot or cold, together or separately, into the steel furnace; a pig-iron bath, and hot or cold steel or iron scrap, direct sponge or Catalan or puddled blooms charged into the bath. The operation is, to a greater or less extent, according to the nature of the materials used, a desiliconization and decarburization of the pig or other crude iron, and its dilution by already purified materials. Manganese is employed at the end of the operation to remove oxide of iron and silica, a regulated amount of manganese remaining in the product. Figs. 2 and 3, Plate IV, represent the hearth and roof of the Pernot furnace; Fig. 1 shows, in cross section, the general arrangeent of open-hearth plant with Pernot furnaces, as generally designed by the author, and now building at two works. The engrav-

Jan 1, 1879

By Robert Archer

Two new alloys of the "strong alloy" class having improved fabricating qualities are described; also methods of producing alloys of the duralumin type with greater strength and hardness than previously obtained, are given. IT is about fifteen years since the development in Germany, largely by Alfred Wilm, of the aluminum alloy called duralumin. In this alloy, combining as it does the tensile strength of mild steel with the lightness and corrosion resistance of aluminum, a distinctly new material was presented to the engineering world. Despite the evident usefulness of this material, however, its commercial development has been slow, due in part to the difficulties involved in its fabrication. In view of the potentially great utility of strong aluminum alloys, it seemed desirable to find means of producing such alloys with better fabricating properties, and work was undertaken with this object in the laboratories of the Aluminum Company of America several years ago. This work has resulted in the production of two new types of aluminum alloy of the "strong alloy" class, having distinctly improved fabricating qualities. The knowledge gained has also made it possible to produce alloys of the duralumin type with greater strength and hardness than previously obtained. There have thus been made available some new engineering materials which it is the object of this paper to describe. These alloys, including duralumin, are fundamentally wrought alloys. Castings of the same compositions, heat-treated in the same manner give inferior physical properties, particularly as to ductility. The statements made subsequently concerning properties and heat treatment apply to material that has received sufficient working to thoroughly break down the cast structure. The material referred to has; in general, undergone a reduction in section of at least 80 per cent. by mechanical working. It may be mentioned in passing that other compositions have been found that are suitable for the production of the maximum physical properties in heat-treated castings.

Jan 2, 1925

By K. Hasselwander, K. Knabel

"A significant area of Outotec’s business involves fluidized bed roasting. With several decades of experience, more than 300 reference plants and strong R&D capabilities, the company provides several industries with optimum processing solutions. Applications include oxidation and sulfation of sulfides found in copper, pyrite and zinc concentrates. Gold production and de-arsenifying roasting are also within this scope. This paper describes the latest furnace developments and includes novel trends. Moreover, hot and wet gas cleaning systems are examined focusing on unit operations related to the removal of components such as dust, SO2 for sulfuric acid production, fumes, halides, Hg, hydrocarbons, nitrous oxides and metals.INTRODUCTIONGenerally, when defining roasting processes, it can be stated that the respective primary pyrometallurgical reaction is exothermic, of gas-solid nature and relates to a value solid product. These processes are a key focus within Outotec’s scope and include: (i) dead roasting (ii) sulfating roasting (iii) partial de-arsenifying roasting and (iv) two-stage, de-arsenifying roasting.Dead roasting involves the oxidation of a given sulfide, thus allowing for a subsequent leaching process, and has been applied to producing ZnO. Dead roasting of pyrite has also been extensively utilized with a primary goal of producing sulfuric acid. In contrast, sulfating roasting involves converting a sulfide to its sulfate, enabling a selective sulfation of components, such as Cu or Co, and their separation from ferrous components during leaching (produced sulfates are soluble). Partial roasting involves partially oxidating the metal sulfide to its oxide with the simultaneous production of gaseous As4O6, which is handled during gas cleaning. The solid product, containing hardly any As, is rich in S and can be fed to a respective smelter (e.g. in the case of Cu). Alternatively, if the production of oxide is required, a dead roasting step is added after the partial roasting step, with the overall process considered as two-stage roasting."

Jan 1, 2012

By Vsevolod Krivobok

IT is generally recognized that "low temperatures" have a definite effect on the properties of metals and alloys. Furthermore, it is also generally understood that the effect is decidedly adverse. The possibility that the same low-temperature treatment might be employed for the purpose of improving certain properties of the .alloys has received less attention until recently, and the experimental and theoretical knowledge consequently is meager. The effect of low temperatures may be studied in two ways: by studying such properties as tensile strength, hardness, impact resistance, etc., at low temperature, and by studying the properties of alloys at room temperature after these alloys have been subjected to a low-temperature treatment. Even in the latter case, certain properties will differ materially from the same properties obtained on identical material but without cold treatment. In other words, subjecting alloys to cold treatment results in an irreversible change in mechanical properties. Changes of this character are usually indications of the appearance of a new phase or phases, and would be likely to occur in alloys which, either by virtue of their composition or by heat treatment, are retained at room temperature in a metastable condition. Consequently, studies of the effect of low temperatures logically should be conducted from the physicochemical point of view, since the results of such studies not only would furnish metallurgists with interesting theoretical data but would clearly indicate the classes of alloys that would hold promise of improvement, and, possibly, of new applications. As the present investigation deals with chromium and chromium-nickel alloys of iron of the stainless variety, it has been thought desirable to present the data concerning low-temperature properties of these alloys, available from the most recent and most comprehensive work of H: S. Russell.' A summary, of these data is given in Table 1. The data are confined to a limited number of alloys of the type dealt with in the present

Jan 1, 1931

By Maxwell Gensamer, Vsevolod N. Krivobok

It is generally recognized that "low temperatures" have a definite effect on the properties of metals and alloys. Furthermore, it is also generally understood that the effect is decidedly adverse. The possibility that the same low-temperature treatment might be employed for the purpose of improving certain properties of the alloys has received less attention until recently, and the experimental and theoretical knowledge consequently is meager. The effect of low temperatures may be studied in two ways: by studying such properties as tensile strength, hardpess, impact resistance, etc., at low temperature, and by studying the properties of alloys at room temperature after these alloys have been subjected to a low-temperature treatment. Even in the latter case, certain properties will differ materially from the same properties obtained on identical material but without cold treatment. In other words, subjecting alloys to cold treatment results in an irreversible change in mechanical properties. Changes of this character are usually indications of the appearance of a new phase or phases, and would be likely to occur in alloys which, either by virtue of their composition or by heat treatment, are retained at room temperature in a metastable condition. Consequently, studies of the effect of low temperatures logically should be conducted from the physicochemical point of view, since the results of such studies not only would furnish metallurgists with interesting theoretical data but would clearly indicate the classes of alloys that would hold promise of improvement, and, possibly, of new applications. As the present investmigation deals with chromium and chromium-nickel alloys of iron of the stainless variety, it has been thought desirable to present the data concerning low-temperature properties of these alloys, available from the most recent and most comprehensive work of H. S. Russell.l A summary of these data is given in Table 1. The data are confined to a limited number of alloys of the type dealt with in the present

Jan 1, 1931

By Hisaaki Takada, Atsushi Yoshida, Kazuo Satoh, Norikazu Nanko, Naoshichi Higashi

Kamioka Mine of Mitsui Mining & Smelting Co., Ltd. is the largest lead-zinc mine in Japan and is composed of two mines, Tochibora Mine and Mozumi Mine, which have daily production rates of 5,200 metric tons and 1,800 metric tons of crude ore respectively. In the mines, there are many massive pyro-metasomatic deposits which have been derived from the replacement of limestone. The deposits are composed of skarn minerals which mainly contain hedenberite. The country rock is generally hard and fine-grained gneiss. These deposits have been mined by means of the sublevel stoping method, induced block caving method and sublevel caving method at Tochibora Mine and mainly by the cut and fill method at Mozumi Mine. Since the 19601s, the trackless mining system has been introduced successfully into both mines, and is still promoted to be applied over wider areas. The underground hauling system is simplified remark- ably and much improved by adopting trackless ramps to the existing vertical and horizontal underground framework. Moreover, through the combination of the trackless mining system with the mining methods stated above, a notable increase in efficiency has been achieved. This is due to the high performance of the introduced machinery, reductions in man power of miscellaneous jobs, and also has enabled a highly efficient performance through its mobility. In addition, as it becomes possible to realize a flexible development to meet the irregularly shaped deposits and also becomes much easier to recover the remaining pillars by secondary mining, the extraction rate of ore has been improved considerably. With the introduction of the trackless mining system, the development method has been changed, thus former hand-hold leg-drills are now mostly re- placed by jumbo-type drills. Repair shops for Load-Haul-Dump machines also have been provided with an established service system. Reinforcement and rearrangement of the ventilation system has been carried out.

Jan 1, 1977

By Alfred W. Gauger, George A. Burrell

The senior author of this paper, while in Colorado on other official business, made a trip to the Cripple Creek gold-mining district to get more data than are at present available regarding the composition of the gas that issues from the rock into the mines of the district. This was done at the suggestion of George S. Rice, Chief Mining Engineer of the Bureau of Mines. There are -many questions of interest and importance in connection with the ventilation of the mines in the Cripple Creek district, such as the menace to life and mining of a suffocating gas entering the mines from the rock, the danger due to powder smoke (from blasting operations), and danger of continued inhalation of rock dust by the miners. This report confines itself to the first problem, the gas from the rock, and principally to one phase of this question, the composition of the gas and its effects on men and lights. A more thorough study of this and other ventilation problems is planned. That the rock gas is a real menace is shown by the fact that miners (variously estimated from 25 to 50 by different persons interviewed) have been killed by it in the 25 years that mining has been vigorously carried on at Cripple Creek. Many men have had narrow escapes from death, some of them having been incapacitated for days. In addition, much loss of time results because at certain periods of the year or on certain days it is impossible to enter some workings. At a few mines, fans force air into the workings, thus supplementing the natural ventilation and much improving conditions, but the improvement is not entirely adequate at all times. Origin of the Gas Lindgren and Ransome1 think that the gas found in the rocks of the Cripple Creek mining district represents the last exhalations of the ex-

Jan 1, 1917