Search Documents

By Glenn E. Craig

The practical and effective pulp distributor here presented is believed to be of a completely new and innovative design. It was developed at the San Nicolas Plant of the Marcona Mining Company in Peru, where it has been thoroughly plant tested using iron ore slurries of a particularly abrasive nature. It has proven to be superior to the apparatus originally installed, or to any observed in operation elsewhere. In plant practice the capacity and efficiency of many process units such as screens, magnetic separators, and jigs are strongly affected by the loading pattern, and for better results the flow of pulp must be proportioned across the receiving lip in equal quantities per unit width. The distributors originally installed on the drum magnetic separators in San Nicolas proved to be unsatisfactory, and several trial modifications failed to show any improvement. As is usually the case, feed rates were being steadily increased, and appreciable losses to tailings resulted. A check of the distributors on the market discloses no reasonable substitute, so efforts were directed toward devising an entirely new type. Required was a positive type of action which would guarantee that the pulp flow be spread equally along the length of the drum. Discussion As indicated, the motivation for development was simple necessity. The plant in San Nicolas crushes, grinds, and concentrates magnetic iron ores of a particularly abrasive nature, and depends largely on magnetic separation to obtain a marketable product. Feed to the numerous drum magnetic cobbers and finishers varies from rod mill discharge at a nominal minus ten mesh to a ball mill fine grind of seventy percent minus three hundred and twenty-five mesh. Operational factors affecting the magnetic separators were well controlled,

Jan 1, 1971

By Robert F. Winkle

A detailed breakdown of mining costs, available to management on monthly and year-to-date bases, is mandatory for a controlled and efficient mining operation. A simple lump sum reporting of costs may indicate a profit or loss differential, but it does not allow an effective search for areas of possible cost reduction. Moreover, functional reporting is necessary on a timely basis so as to note trends of increasing costs In specific areas, which in turn allow possible preventive action by management. Definitive cost information helps to eliminate the tendency to overlook areas where cost Improvements can be made. A good cost control system points out salient operational weaknesses by: ( 1 ) allowing comparison of functional costs with similar costs of other mines and (2) pinpointing sudden increases over unit empirical costs within the organization. In general, the cost accounting structure is relatively uniform within large open pit mines, but surprisingly some systems will overlook the need for detailed breakout in comparatively high cost areas. In some other systems, unrelated costs will be lumped together, preventing careful analysis of cost accrual.

Jan 1, 1979

By C. P. Smyth

Large volumes of quantitative geochemical data, presenting a formidable interpretation task to geologists, are generated in the course of exploration drilling for new ore deposits. The incorporation of geological expertise into computer programs developed for the interpretation of this data would improve the speed and accuracy with which it is interpreted. A detailed analysis of the geochemical log interpretation problem, together with a survey of relevant research in Artificial Intelligence and petroleum well- logging techniques, confirms, that artificial intelligence, particularly as developed in the fields of expert systems and pattern recognition, provides techniques for implementing such data interpretation programs. In addition, it provides data analysis techniques significantly more powerful than those currently applied to geochemical data, and very appropriate to the hypothesise and test' character of mineral exploration problem-solving. The conversion of raw borehole log data to meaningful higher level geochemical entities, in terms of which geological reasoning may take place, is a critical step in applying these techniques to log data analysis. A method of achieving this conversion as an exercise in signal-to-symbol transformation is presented.1

Jan 1, 1987

By Lennox A

In an attempt to increase underground productivity Coal and Allied has introduced a continuous haulage unit into it's Moonee colliery. A second unit is planned for Nallarah colliery in the near future. Both systems will be roof mounted or monorail type and manufactured by Joy Manufacturing Pty Ltd. The introduction of these machines is seen as a logical step in improving the efficiency of mining with continuous miners. This could be in conjunction with longwall mining in the rapid development of gate roads or, as in the case with these machines, as conventional development and extraction units. The advantages of the continuous haulage system are; Relatively low cost. 2 Ability to obtain high productivity in irregular or disturbed coal reserves not suitable for longwall mining. 3 Increased worker safety with the elimination of shuttle cars and the majority of trailing cables. 4 Increased productivity independent of soft or difficult floor conditions. At the time of writing the Moonee installation is 6 months old. The Nallarah machine is due for delivery March 1988.

Jan 1, 1988

By I Thin, I Sheppard

Resin encapsulated rock bolting practices have been adopted by Mount Isa Mines since the early-1980s. Fully encapsulated rock bolt systems meet designated requirements for long-term ground support in the mines. A variety of rock bolts, resins and installation methods have been utilised over this period in underground mining. As a parallel to this evolving application, Mount Isa Mines have tested various resin encapsulated rock bolt systems. Testing has included routine underground pull testing and the development and implementation of the push test for the entire encapsulated bolt length. The latter test enables a greater understanding and representation to be had of the overall mixing, level of encapsulation and capacity of the system. Rock mechanics at Mount Isa Mines undertake evaluation of new bolt systems that become available, in addition to the maintenance of compliance with quality control measures for the existing systems. Improved methods of installation and systems are also investigated to further the cost-effective nature and minimise risks associated with resin rock bolt practices.

Jan 1, 2002

By Jeremias K. Chitunda

Significant cost savings and improved ground stability are two initial indications from the current wet process shotcrete ground support program at the Lakeshore mine. The area of shotcrete for ground stability is not strange to the Lakeshore operation. Since the beginning of the project, various shotcrete techniques have constantly been experimented with, incorporating all the latest technological developments. Over the years, the use of shotcrete has been employed as a primary, temporary, or permanent support, singly or in combination with rockbolts and steel sets. The extent of shotcrete usage compared with steel sets and rockbolts has varied from time to time as dictated by the overall state of the art. In 1972, for example, the ratio of the linear drift footage supported with shotcrete to that supported with steel sets averaged 1.0. In 1973, that ratio was about 3.0. Overall, for the Lakeshore mine, there are about 8000 drift ft of shotcrete, 8000 drift ft of steel sets and timber, 750 drift ft of formed concrete, 21,000 drift ft of rockbolts, and 3700 drift ft of combined type support.

Jan 12, 1974

By Chauncey Berrien

THE Hawkesworth detachable drill steel shank and bit were invented by A. L. Hawkesworth; while he was a mechanical foreman for the Anaconda Copper Mining Co., at Butte, Mont. Mr. Hawkesworth died on June 16, 1925, at the time that his invention was practically a proved success. The first application for patents was made by him in November, 1918, and the bit is now being manufactured under patents issued in 1922 and 1923. The credit, for its development in the early stages belongs to A. L. Hawkesworth, Roy S. Alley, Harry A. Gallwey, E. J. Bowman and various officials of the Anaconda Copper Mining Co. Later improvements, manufacturing problems and the direct usage in the mines were originated and perfected by the mechanical department under C. D. Woodward, E. R. Borcherdt, head of the Rock Drill Equipment Department, Robert E. Kelly of the Mechanical Department, and various operating department heads of the Anaconda Copper Mining Co. The author wishes to acknowledge the assistance of these officials in the preparation of this paper.

Jan 1, 1930

By Louis V. Bender

THIS paper gives a short review of the installation for and the use of gas, as a. fuel, at the Anaconda Reduction Works of the Anaconda Copper Mining Co. Before putting in gas tile fuels used were pulverized coal, lump coal, coke distillate and oil. These fuels are now almost entirely eliminated. For nearly fifty years bituminous coals from Wyoming and Montana fields had been used. These coals were of a good grade, analyzing 11,300 B.t.u. and having an ash content of 12 per cent. When hydro-electric power replaced steam-driven equipment, the coal requirements were reduced; and, on account of improvements in metallurgy and/ or in furnace design, the quantity was lessened. Later, oil and distillate were introduced and used in some of the operations. All of these things tended toward the lessening of the amount of coal used, and had it not been for the increase in the size of the plant, the tonnage used would have been small when the change was made to gas.

Jan 1, 1932

By Jinrong (Patrick) Zhang

Improvement of conventional flotation efficiency, separation of carbonates from apatite, recovery of phosphate values from phosphatic clay and other ways of utilizing the clay, disposal of clay slurries and subsequent reclamation of the settling areas, and conservation of resources and energy remain major challenges in the beneficiation area for the phosphate industry. These problems have been actively investigated by the industry, government agencies, and research organizations for decades with modest success. However, some recent research activities have generated promising results and possible new technologies. The dominant position of the Crago process in phosphate beneficiation is being challenged by some of the single stage processing schemes. Heavy media separation enables one producer to process a portion of high carbonate ores. Separation of dolomite from apatite by reverse flotation of carbonates with phosphate depressants showed potential for industrial application. Consolidation of phosphatic clays in mine cuts using a modified "sandwich" process is being tested. Beneficiation in the acidulation plant or grinding at the mines may be considered in the future.

Jan 1, 1993

By Restarick C. J & Stewart P S B, Kelsall D. P

Over a four-hour period of steady plant operation samples were taken at regular intervals from points within the grinding and flotation circuits. Size fractions of each composite sample were analysed for lead and zinc values and a comparison made of the behaviour of the lead, zinc and gangue minerals, size by size throughout the whole circuit. Analysis of the breakage behaviour using dynamic mathematical models gave the rates of breakage of each size fraction of each main component. Simulated grinding experiments showed that the main grinding circuit had sane reserve capacity. In the lead flotation circuit all lead values between 150 mesh (Tyler) and 5 microns had excellent flotation characteristics, and a major proportion had a high rate of flotation which was practically the same for all sizes. Increase in overall lead recovery would require improvement of the flotation behaviour of ultra-fine lead minerals. These were slow floating and were responsible for approximately half the lead losses in the final zinc concentrate and one third of the lead losses in the final tails.

Jan 1, 1980

By Kazem Oraee-Mirzamani

Blasting operations generate seismic effects in underground mines. These effects apply additional dynamic loads on the support system, which should bear both static and dynamic loads. Static loads are caused by the weight of the superincumbent strata, while dynamic loads occur as a result of blasting in the mining area. Identification of the origin and determination of the support system behavior in natural frequencies is crucial in assessing the stability of underground mines. This is because resonance occurs when a support is vibrated with its natural frequencies, which can cause a vibration with the maximum amplitude and subsequently cause extreme deformations. The mechanism of support system deformation during dynamic load displacement has been studied and numerical simulation for the impact of the dynamic loads on stability of supports is carried out using finite element method. The paper introduces a simple technique for improving stability and safety of mining operations. Results obtained and the methodology adopted in this research can help mining design engineers make decisions on adequate support for active mining operations.

Jan 1, 2011

By Francis M. Walters

THE problem of making iron-manganese alloys of scientific purity is a rather difficult one. They cannot be prepared in air because of the readiness with which the metals oxidize at the temperature of melting; and they cannot be prepared in vacuum because of the, high vapor pressure-of- manganese. The very property of: manganese which permits it to be purified interferes with the utilization of the best method of making pure alloys. Accordingly, it is necessary to use a gas atmosphere which will not affect the-properties of the alloys. The gases available for the purposes are hydrogen; helium and argon. Nitrogen forms intermetallic compounds with manganese very readily. Hydrogen, while valuable as a deoxidizer and having the advantage of being comparatively cheap, is explosive over a wide range and, has a rather high thermal conductivity. Helium is reported as, costing little but is difficult to secure at a reasonable price and also has a conductivity nearly as high as hydrogen. Since argon has a sufficiently low thermal conductivity, it has been selected for use in one induction furnace for melting, under a controlled, gas atmosphere, in spite of its cost, which is so high (70 cents to $1.50 per cubic foot) that it must be stored and purified.. Such a gas atmosphere-as argon makes necessary the use of the, high-frequency induction method of heating. This involves, a non-metallic container for the gas; .which is most conveniently of fused quartz or glass. The next

Jan 1, 1929

By Hamid Maleki

A geotechnical monitoring program has been implemented at Energy West Mining Company for enhancing site-specific evaluation of longwall stress conditions. This program consists of underground measurements at five locations in two neighboring mining districts located in the Hiawatha and Blind Canyon Coal Seams under moderate to deep cover. Within the last five years, additional measurements, including data on recorded seismic events and face conditions, have been incorporated into the data collection program together with detailed geologic mapping of longwall gateroads. In conjunction with the measurement program, the authors have completed detailed boundary-element stress analyses of the mine plans. Models have been calibrated using the data from in-mine instrumentations and then routinely used for evaluation of mine plans at depths approaching 2,600-ft. The work has improved our understanding of load transfer, seismicity and yield pillar performance. It has identified areas of potential increased stress levels at certain longwall face positions and provided guidance to measures that could be considered to mitigate the potential for these increased stress levels.

Jan 1, 2009

Firedamp drainage has become an essential part of many mine environmental systems, and new applications are arising. Installations are evolving further to satisfy ever changing basic requirements, standards, and iniilny needs. In this paper, water seal, vacuum based installations are considered, as well as moni- toring, protective and control systems which have been developed for continuous, manless, and trouble free operation. Some factors affecting plant capacity and extractor per- formance are identified and assessed. INTRODUCTION Firedamp drainage applications are incr- easing world wide as mining engineers strive for improved safety and security, and further concentration of coal output. Fewer and fewer mines are able nowadays to satisfy coal prod- uction and firedamp control requirements solely by air dilution or by air dilution and underground firedamp extraction plants. As a result, dependence on surface extraction plants is increasing. This paper deals with som requirements and applications of such installations. I. DEVELOPMENT AND PRACTICE Firedamp drainage has existed for over 250 years following the early work of Carlisle Spedding at Whitehaven (1730). Some fundamentals of current firedamp drainage systems can be recognised in the

Jan 1, 1982

By T. C. Murphy, W. Taciuk

In 1966, the Iron Ore Company of Canada commissioned a wet magnetic scavanging plant for the recovery of fine magnetite values p.resent in spiral tailings discharged from a spiral gravity separation process. The plant includes dewatering, grinding, classification, thickening, mini-wedge screening, and primary, secondary and tertiary wet magnetic separation stages. The source of feed varies in quantity and quality, so the original design included variable operational procedures to deal with these conditions.

Jan 1, 1972

By G. H. Hopkins

Like most industries, the refining industry has in recent years been confronted with the problem of a decreased martin of profit, due both to a general lowering of prices and to rising costs. This has resulted in accelerating a program of increased efficiency an evidenced by improved methods and the installation of equipment designed to affect a number of economies hitherto regarded as unimportant. Perhaps the most important of these has been that of fuel economy for, as is not often realized, a refinery consumes about one-tenth as much fuel as it produces. A recently completed canvas., made by the Bureau of Mines for the purpose of determining the trend of fuel consumption at refineries in the United States, showed the following outstanding points, (1) a decrease in the use of oil for fuel in 1926 of approximately 4,000,000 barrels as compared with 1925; (2) a small decrease in the use of coal; (3) a material increase in the use of gas, both natural gas and refinery gas; and (4) a considerable increase in the use of petroleum coke.

Jan 1, 1927

By W. P. Sykes

SEVEN years ago, Dr. S. L. Hoyt1 presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned.

Jan 1, 1938

By J. Coffin, R. Multani, C. Deredin

Glencore’s Strathcona Mill has recently evaluated a pyrrhotite depressant combination of diethylenetriamine (DETA) and sodium metabisulfite (SMBS) to improve its overall plant pyrrhotite- pentlandite (Po-Pn) selectivity, with the aim of producing a higher quality nickel concentrate. In a previous paper, key findings from a comprehensive lab-scale program (completed at the XPS Centre) were summarized where, of the depressants tested, DETA/SMBS combination was found to be the most effective in improving the Po-Pn selectivity. The present paper describes the metallurgical program recently completed at Strathcona Mill; DETA/SMBS evaluation on select plant “grab” samples as well as the major results of three DETA/SMBS plant trials conducted on several plant ore feeds (long-term testing). Interestingly, it was found that there was variable success in using DETA/SMBS depressants on the different plant ore feeds; DETA/SMBS (dosage: 25/50 g/t milled feed) on lower Cu feeds demonstrated a ~2% Ni recovery increase at the same Ni grade. On the other hand, higher Cu feeds demonstrated virtually no benefit from DETA/SMBS at the same plant dosage, suggesting that higher DETA/SMBS dosage (at specific locations) than that tested is required to overcome the increased Cu-DETA complexation for these particular feeds. Glencore Nickel – Sudbury Integrated Nickel Operations owns and operates Strathcona Mill which has been processing Ni-Cu ores from the Sudbury Basin since 1968. The valuable sulfides are pentlandite (Pn) – (Ni,Fe)9S8 and chalcopyrite (Cp) – CuFeS2, majority of the sulfide gangue is pyrrhotite (Po) – Fe(1-x)S [0 < x ≤ 0.125] which is present in two forms: hexagonal Po (Fe9S10) and monoclinic Po (Fe7S8) (Multani & Waters, 2017; Lawson et al., 2014). Currently Strathcona Mill processes ore mined from two primary sources from the Sudbury area and produces two concentrate streams: (1) nickel-copper concentrate that is sent to the Sudbury Smelter; and (2) copper concentrate that is shipped to the Fonderie Horne (Glencore Copper, Rouyn-Noranda).

Jan 1, 2019

Anglo American Platinum practices fine grinding in its processing plants to enhance the liberation of valuable minerals. If the fine particles of valuable minerals generated during fine grinding are not recovered during the flotation process, this could significantly contribute to the overall losses. This study examines the flotability of fine moncheite (PGE mineral) particles in a controlled environment (moncheite size distribution, concentration and liberation). A barren Norite ore ground to 40% and 80% passing 53µm was spiked, with four different size fractions of moncheite (-5, -10+5, -25+10 and -53+25µm) in order to evaluate the effect of particle size on flotation. The investigation also included the effect of energy input and collector dosage on the flotation of two moncheite size fractions, namely -5µm and -10+5µm. The results showed that the moncheite particle size has a significant impact on flotation. Coarse particles (-53+25µm) showed the highest Pt flotation kinetics and overall recoveries. The -5µm size fraction of moncheite could also be recovered by flotation, however, at a lower rate compared to the other size classes investigated. The increased collector dosage of 300g/t at the finer Norite grind of 80% passing 53µm enhanced the flotation rate of the -5µm size fraction of moncheite when compared to the lower collector dosage of 150g/t. The higher energy input during laboratory flotation, at an impeller speed of 1000rpm also increased the flotation rate of the -5µm size range, however, at a lower concentrate grade, when compared to the lower impeller speed of 700rpm. More favourable Pt flotation kinetics data was obtained for the -53 +25µm size fraction of moncheite at the fine Norite grind when compared to the coarse Norite grind. Keywords: flotation, moncheite, particle size, energy input and SIBX

Sep 1, 2012

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched. A new paradigm divides pillar failure into three categories:

Jan 1, 1999