Search Documents

By R. Simon

The sources of energy dissipation for concentrated loadings on rock are considered in an attempt to account for the experimentally measured magnitude of the work required to break out a unit volume of rock from the free surface of an essentially semi-infinite medium. It is concluded that most of this work probably represents the elastic strain energy developed by the loading in a much larger volume of rock beneath the loaded region than the volume of the rock fragment broken out to the side of the loaded region. This strain energy is largely dissipated in the form of stress waves generated by the high rate of unloading produced by the propagating cracks. The energies associated with the formation of the new surfaces of the cracks and with the stress waves generated directly by the loading process are computed to be negligibly small. Possibilities for improving the utilization of energy to drill rod. subject to the geometrical limitations imposed by down-hole operation, are discussed. It is pointed out that any such possible improvements would probably have to be differential ones, since each rock configuration of more favorabIe loading geometry that can be created down the hole is accompanied by a complementary configuration of less favorable loading geometry. INTRODUCTION Dislodging each cubic inch of rock from the bottom of the hole by the action of a bit requires the expenditure of an amount of energy that varies from approximately 5,000 in.-lb to approximately 100,000 in.-lb, depending on the hardness of the rock, or, more technically, upon its fragmentation strength.1 In this paper we will discuss (I) why the energy expended in drilling is so large, (2) what happens to this energy upon completion of the drilling process, and (3) what are the possibilities for reducing the magnitude of the energy required to drill rock. DETERMINATION OF ROCK DRILLING ENERGY The volume of rock removed per unit time from the bottom of a hole of diameter D is evidently (7/4)D2R, where R is the rate of penetration of the bit. If P is the rate at which work is done by the bit on the rock at the bottom of the hole, the energy required to break out a unit volume of rock is given by: Ev =(4/p) P/D2R............(i) For rotary drilling, of either the rolling-cone or drag-bit varicty, P = 2pLN, where L is the torque resistance to rotation at the bottom of the hole and N is the rate of rotation of the bit. L is essentially the same as the torque measured at the rotary table only when drilling in shallow holes. The energies expended in rotating the drill string against the frictional resistance of the walls of the hole and and against the viscous drag of the drilling fluid are extraneous to the subject under consideration, although these may be much greater in magnitude than E, when drilling in a deep hole. For percussion drilling, P = fE where f is the percussion frequency and E is the work done on the rock per impact. The latter quantity can be both computed and measured for a percussion drilling machine. 2 (Under satisfactory drilling conditions, defined in terms of ranges of numerical values of certain dimensionless parameters, E is only 30 to 50 per cent less than the impact energy of the striker.2) Alternatively, E, may be measured directly by dropping chisels shaped like bit edges, backed by rigid weights, onto the surfaces of laboratory rock samples of effectively semi-infinite extent. Under these circumstances, essentially all of the impact energy is converted to work done on the rock, and the relationships among volume of rock broken out, chisel shape, impact energy and indexing distances can be obtained.3 The values of the energy required to break out a unit volume of rock under favorable circumstances are substantially in agreement for rotary drilling, percussion drilling and drop testing at atmospheric pressure. The energy per unit volume is a quantity of the order of magnitude of roughly twice the com-pressive strength of the rock as measured by a uniaxial loading test. The phrase "order of magnitude" in this paper means from about 1/3 as much to 3 times as much; i.e., the energy per unit volume may range from roughly the same up to several times

By William Gleason

"There are few people more qualified to speak of the tumultuous times in the global mining industry during the past four years than Newmont Mining Corp. president and chief executive officer Gary Goldberg.Goldberg stepped into his current position in 2012, just before MINExpo 2012. Gold prices had hit record highs not long before that ($54.15/g or $1,856.40/oz on Sept. 8, 2011), expansions were happening around the world and the gold mining sector was still living in the glow of one of its longest upswings in history.That all changed between April 8 and April 15, 2013 when the price of gold dropped by nearly $200/oz ($46.27/g or $1,586.20/oz on April 8 to $40.45/g or $1,386.80/oz on April 15), putting an end to the decade-long mining boom and forcing mining companies like Newmont to re-evaluateeverything.Three years later, with the gold sector recovering, Newmont Mining is not only surviving but is thriving with a pair of mines coming online, Long Canyon in Nevada and Merian in Suriname. On Oct. 1, the Merian Mine went into production on time and more than $150 million under the initial development capital budget.Goldberg, who was one of the featured speakers at the opening session of MINExpo International 2016 on Sept. 26, also spoke with Mining Engineering about the previous four years and the future of the industry.“Mining goes through cycles all the time and gold is no different,” Goldberg told Mining Engineering when asked about surviving the downturn since 2012. “I thought it was important that we take a good methodical and steady approach across the business to determine what was the right thing to do and to set the business up to improve performance. Anyone can cut costs for the short term, but we set out to do it in a sustainable and reliable way. We created a program we call Full Potential to look for sustainable ways to reduce costs and improve productivity. That program has taken more than a billion dollars out of our costs since we implemented it 2013 and that shows up in our results. Our all in sustaining costs are down 28 percent and our productivity is up 39 percent.”During the downturn, Newmont restructured its business model, sold off some assets and created a leaner, more nimble operation. It has paid off with the addition of two new mines and the acquisition of another, the Cripple Creek & Victor Mine in Cripple Creek, CO.“The gold industry had not seen a downturn in 12 years. We had half a generation that had not experienced a downturn, so helping them through that in an organized way and keeping a view toward the long term throughout the downturn was important. We were one of the few companies that continued to invest in assets,” he said."

Nov 1, 2016

By N. Snyders, I. Mwandawande, S. M. Bradshaw, M. Karimi

"Computational fluid dynamics (CFD) was applied to predict the average gas holdup and the axial gas holdup variation in a 13.5 m high cylindrical column 0.91 m diameter. The column was operating in batch mode. A Eulerian-Eulerian multiphase approach with appropriate interphase momentum exchange terms was applied to simulate the gas-liquid flow inside the column. Turbulence in the continuous phase was modelled using the k-_ realizable turbulence model. The predicted average gas holdup values were in good agreement with experimental data. The axial gas holdup prediction was generally good for the middle and top parts of the column, but was over-predicted for the bottom part of the column. Bubble velocity profiles were observed in which the axial velocity of the air bubbles decreased with height in the column. This may be related to the upward increase in gas holdup in the column. Simulations were also conducted to compare the gas holdup predicted with the universal, the Schiller-Naumann, and the Morsi-Alexander drag models. The gas holdup predictions for the three drag models were not significantly different. IntroductionColumn flotation is an important concentration technology that is used in the mineral processing and coal beneficiation industries. The growing interest in the use of column flotation in mineral processing has been attributed to the simpler flotation circuits and improved metallurgical performance compared to conventional flotation cells (Finch and Dobby, 1990). Flotation columns have also found other applications outside mineral processing, such as de-inking of recycled paper (Finch and Hardie, 1999).In column flotation, a rising swarm of air bubbles generated by means of air spargers is employed to collect the valuable mineral particles and separate them from the gangue minerals in a countercurrent process. Wash water, which is continuously fed at the top of the column, is used to eliminate entrained particles and stabilize the froth. The column volume can be divided into two sections – the collection zone in which the bubbles collect the floatable mineral particles, and the cleaning zone (or froth zone) where product upgrading is enhanced through the removal of unwanted particles entrained in the water mixed with bubbles from the collection zone."

Jan 1, 2019

By R. E. Hucko

The goal of the U.S. Department of Energy (DOE) coal preparation R&D program is to develop technology to reduce the ash and sulfur contents of United States coals to levels such that the resultant product can be formulated into a high- quality solid or slurry fuel that could replace oil or natural gas in both new and retrofit applications. The Coal Preparation program is implemented by the Pittsburgh Energy Technology Center (PETC) and is conducted both in-house and by a cross section of industrial organizations, universities, and national laboratories.

Jan 1, 1986

By W. T. Abel

The difficulties associated with wet-processing fine size coal led the Bureau of Mines to investigate a dry process for removing pyrite from coal pulverized to powerplant fineness. The dry process that was investigated consists of two cleaning steps: First, centrifugal separation is used to remove a fine, pyrite-depleted portion as a product; second, the remaining coarser, pyrite-enriched portion is taken to electrostatic separation in which pyrite is concentrated and rejected. Ball milling and Hardgrove milling were used to pulverize the coal. Three coals from the Pittsburgh seam were treated by the dry-removal process. Over 55 pct of the pyrite, which amounted to 70 pct of the available pyrite, was removed in a reject of 10 to 20 pct from one of the coals. Similar treatment of the other two coals removed about 35 to 50 pct of the pyritic sulfur, which amounted to about 70 pct of the available pyritie, sulfur from these coals. Both centrifugal and electrostatic separations were more efficient when pyrite particles were as large as possible. Separation efficiency was improved by confining the particle size of the feed to a relatively narrow range and by avoiding excessive amounts (more than 10 pct) of dust in the electrostatic range. The removal efficiency was increased with the use of stage grinding.

Jan 1, 1973

By Lloyd Williams

1. Reserves have been estimated for three coal beds in Bledsoe County, Tenn.: Morgan Springs, Lantana, and Sewanee. The Richland and Nelson beds occur in Bledsoe County also, but there was not enough information on them for making an estimate of reserves. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated at 43 million tons as of January 1, 1954. Of this total, 22 million tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient for making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves deter-mined by this investigation.

Jan 1, 1956

By Athena C. Denivo, Pablo V. Lopez, Michael McMaster, Sissy Nikolaou, Alfred H. Brand

"The paper presents the history of development of the United States Tennis Association (USTA) site, focusing on geotechnical, geoseismic, and foundation engineering challenges associated with it. The site is located at the Flushing Meadows Corona Park area of Queens, New York. Now home to the Billie Jean King National Tennis Center (BJKNTC), the site used to be a biologically rich, tidal salt marsh that extended south from Flushing Bay and overlaid an ancient buried valley. In early 20th century, Brooklyn Ash Co. was contracted to fill the marshland with cinders and furnace ashes. F. Scott Fitzgerald describes the “Valley of Ashes” as “a fantastic farm where ashes grow like wheat into ridges and hills and grotesque gardens; where ashes take the forms of houses and chimneys and rising smoke, and finally, with a transcendent effort, of ash-gray men who move dimly and already crumbling through the powdery air.” In 1939 the site was leveled and filled to host the World’s Fair and refilled again for the 1964 World’s Fair.The USTA moved to the site in 1978 and in mid-1990’s constructed the 23,000-seat Arthur Ashe Stadium (AAS). Currently, USTA has a Strategic Vision Plan venue with several interconnected construction projects including buildings, infrastructure upgrades and improvements to site circulation. In addition to a historical walkthrough, the authors will discuss technical challenges of supporting these developments through layers of fill, thick organic silty plastic clays and regional varved soils with bedrock found 300 to 400 feet deep. The subsurface is not only a weak foundation medium, but is susceptible to large amplification of seismic waves propagating from the bedrock during earthquakes. The developments are usually founded on project-specific pile foundations that carry static loads in deeper layers and accommodate lateral demands and performance objectives. Engineering innovations from the most recent development, the roof structure over AAS, will be discussed."

Jan 1, 2016

By M. Marinov

The Bulgarian deposits of quartz-kaolin raw materials are localized in the NE Bulgaria. For many years, the quartz-kaolin sand separation has been performing by water washing technology. After wet separation the raw material yields two products ? washed kaolin (different grades) and quartz sand (different grades). Research and development program has started to improve the quartz-kaolin sand separation. The program has undertaken an increasing of processing capacity, to decrease the losses in the tailings and to provide production of new quartz sand grades. The kaolin-silica raw materials from Vetovo open mine and the technological tailings from Vetovo processing plant were characterized. It was established that there are a lot of losses of quartz in final tailings. New approach on kaolin-silica raw material separation was tested in laboratory scale. The test work was performed on Derrick Stacksizer screening machines. The results of laboratory experiment show that there are possibilities to increase the quartz sand recovery and to start the production new grade sand. The full-scale pilot test was performed including the following units: two Derrick Stacksizer screening machines equipped with 0.430 mm and 0.150 mm opening Derrick Urethane Panel, respectively; Flat bottom DN 500 Hydrocyclone and DN 100 Hydrocyclon. The pilot test data clearly demonstrate that the Derrick Stacksizer screening machines are suitable for Bulgarian silica-kaolin raw material. Based on the test data a new quartz-kaolin separation technology was developed. The new technology was introduced in Vetovo processing plant increasing processing capacity and decreasing the losses of quartz in final tailings. Additionally the production of silica sand grade PK 0.16 is increased and starts the production a new grade PK 0.10.

Sep 1, 2012

By Renxing Li, Yongyong Gong, Yufeng Cheng, Zhenxing Yin, Xin Cao, Qijie Zhai

"The influence of electric current pulse (ECP) on the solidification structure of SUS430 ferritic stainless steel (FSS) was investigated in the current study. The technology of ECP has been widely used to improve the properties of metals with relatively low cost. The parallel electrodes were inserted into the free melt surface to constitute a current loop. The different influences of three parameters on solidification structure were studied by changing the peak current value, frequency and treating time respectively. The results indicated that the ECP significantly increased the number of equiaxed grains of SUS430 FSS. The as-cast structure without ECP treating was almost wholly columnar, while the number of equiaxed grains of the specimen, which was treated 3min with a peak current of 400kIA, increased to 2698 in the observed surface. To get the best refinement, an optimum range of these three parameters is required and the peak current value plays the most important role.IntroductionFor the lack of nickel resource and the pressure of environment protection, ferritic stainless steel is increasingly adopted to replace the austenite stainless steel because of its low nickel content and good mechanical properties. SUS430 steel is a typical example with excellent performance and relatively low price to replace the application of austenitic stainless steel[1-3]. This type of steel with high thermal conductivity coefficient, low expansion coefficient, good oxidation resistance, excellent stress corrosion resistance and other fantastic characteristics is often used to make components which need to have resistances for atmosphere, water, steam and oxidizing acid corrosion[4]. Since the developing of columnar grains and low toughness at high temperature, its products are easily crinkled and cracked during the subsequent rolling process[5]. The application of ferritic stainless steel is limited by these defects[6-8]."

Jan 1, 2012

By B. D. Thomas

When the origin and early plans, of Battelle Memorial Institute were described in this journal in October 1929 by R. W. Gillett the first director, the doors of the laboratory had just been opened and the hope of the founder that the institution serve the world by research for industry still existed only as an ideal in the minds of the thirty or so employees who then constituted the staff. Since that time the country has experienced troublous times. A devastating depression plunged the entire world into an unprecedented period of financial and industrial inactivity; and the slow recovery of the late thirties was soon to be overtaken and overwhelmed in the violence of war. Through this time of stress Battelle has continued to grow. The staff has increased to almost 600; buildings and equipment have been added, until now it stands in a place of pre-eminence in the metallurgical and engineering world.

Jan 1, 1944

By RIINA SALMIMIES, ANTTI HAKKINEN, PAULA VEHMAANPERA

Better understanding of the mechanisms and kinetics of dissolution can benefit several industrial processes. For example, iron can be leached from clays, which can be further used as a raw material in the ceramic industry. Another important application is the regeneration of ceramic filter media, which are used in the dewatering of iron ores. Dissolution of iron oxides in mixtures of acids is fairly uncommon and a less well-understood phenomenon, but it can result in a more efficient process. This work also shows that the determination of dissolution mechanisms and kinetics is not straightforward in different acid systems.

By Mario Terceros

En el presente artículo se muestra la tecnología Cutter Soil Mixing (CSM) como un avance muy importante en la construcción de muros enterrados. Esta se ha mostrado muy eficaz y eficiente, no solo en obras de sostenimiento y contención, sino también en cortinas de muy baja permeabilidad y de aislamiento de suelos contaminados.

Apr 30, 2019

By Charles R. Harrison

The purpose of this study and resulting development of the training program, "Safety--Let's Make It Happen" was to determine the relation of concepts to the development of desired Health and Safety behavior. After extensive pre-contract study, it was hypothesized that improved acceptance and understanding of the Federal Coal Mine Health and Safety Act of 1969 could possibly contribute to the reduction of accidents. Second, in order for an individual to accept and understand the Act, he or she must have a working knowledge of its purposes and application. Third, acceptance and understanding of the Act, necessary to protect the individual from negligence, was imperative. Fourth, an actual operating company could provide the base in which to test these hypotheses in a meaningful manner and develop this type of training program. Six assumptions were agreed upon before embarking on this study and training program development. (1) In the cognitive process, a concept introduction into an individual's personality may result in a behavior quite different than if he or she had been exposed to a different concept.

Jan 1, 1977

By Zsuzsanna Zborovszky

Experimental study directed toward gaining improved understanding of the exact mechanisms causing ignition in the PTB breakflash. Investigation and comparison of tungsten and copper wires as to their ability to cause hot wire ignition. Evaluation of the importance of discharge duration in the ignition process. Study of the parameters influencing the duration of a discharge (minimum discharge voltage, purity of electrode materials, purity and properties of the gaseous atmosphere contaminations, deposits on the electrode surface).

Jan 1, 1976

By Ingo Kaundinya

"INTRODUCTION Tunnels are important elements of the German federal road network which have to cope with an increasing traffic load especially of heavy goods vehicles. In order to ensure a high availability and safety level for these key infrastructures, big efforts are required by owners and operators in order to keep all infrastructures up to date. This mainly relates to current European regulations regarding tunnel safety (Directive 2004/54/EG) [1] and their national implementation, which must be fulfilled by many existing tunnels. In this context the German Federal Government spends more than 1.1 billion € for the structural and operational retrofitting of more than 120 existing road tunnels. As many of these projects have recently been finished or are still under progress, experiences and best practices could be reported. After the description of current requirements in national standards regarding structural fire protection, the paper gives an example for an upgrade of a tunnel’s fire protection by installing an additional fire protection system, which is a quite costly measure. Another possibility to fulfill current requirements regarding structural fire protection could be the numerical proof of sufficient bearing capacity of a structure. The influence of different fire loads and fire durations on the bearing capacity of typical road tunnel structures have been investigated in a research project funded by the German Federal Ministry of Transport (BMVI) and coordinated by the Federal Highway Research Institute (BASt). The results of this research project have been used to define a procedure how to investigate existing tunnels regarding structural fire protection. Finally, the research results have also been the basis for a current update of national standards for tunnel construction. REQUIREMENTS REGARDING STRUCTURAL FIRE PROTECTION The structural fire protection design of road tunnels is usually based on temperature-time curves of exposure to fire, for simplicity called ""fire curves"". The fire development after fire growth is illustrated with fire curves. Fire curves can be subdivided into a heating-up phase, a fully developed fire phase, and if applicable, into a cooling-off phase (cf. Figure 1). During the fully developed fire, the fire remains at a certain temperature level."

Jan 1, 2016

By Peter Fischer

Between 45,000 and 50,000 claims for subsidence are submitted each year to the German hard coal industry. In order to improve the service to claimants a quality management was established in 2005. This paper describes the process now used for handling these claims. A quality check has also been carried out by way of a customer survey, which was performed by an independent research agency. The results of the survey are presented in this paper. In Germany, research into mining subsidence mainly involves the prediction of ground movements caused by deep mining operations. Special areas of research are subsidence reducing aspects of the extraction panel planning, especially from the point of view of mining dynamics, as well as securing and restoration measures. This work seeks to prevent or minimize mining-induced damages close to the surface, for instance, buildings or infrastructure installations (such as pipelines), or underground mine openings (e.g. shafts). Roof collapses and surface fractures caused by shallow mine workings of an earlier era currently constitute a special area of investigation.

Jan 1, 2006

By Sunil Vytla, Agus Sasmito, Akash Adhikari, Srivatsan Jayaraman Sridharan, Purushotham Tukkaraja

Previous studies on blast fumes (carbon monoxide and nitrogen dioxide) clearance and workplace reentry time have overlooked the effects of toxic gases trapped in the muck pile. The currently available models for calculating the mine reentry times assume that all post-blast fumes are emitted upon detonation. However, recent studies reported that as much as 60 to 70% [1–5] of the fumes or gases produced during an underground development blasting could remain trapped in the adjacent rock mass or in the muck pile. Trapped fumes are slowly released [1–5], and when disturbed, high concentrations are released, representing a possible risk during the loading and transportation of the muck pile. In this study, mathematical models were developed using computational fluid dynamics to understand the behavior of the trapped fumes and their effect on mine reentry time. The three scenarios considered for this study include (i) gas emission source with no muck pile volume, (ii) gas emission source with non-porous muck pile volume, and (iii) gas emission source with porous muck pile volume. The estimated reentry times in all three scenarios were compared to see how porous media affects dilution time. It was observed that scenario 3, with fumes trapped in the muck pile, took a significantly longer clearance time (more than double) as compared to scenarios 1 and 2.

May 17, 2022

By Kai Koosmen, Mehdi Serati, Tengzhou Wang

Spalling and rockburst are unwanted brittle failures at the boundaries of underground excavations that are commonly observed in hard rock and high-stress environments at significant depths, although, spalling has also been observed in comparatively shallow soft rocks. The crack initiation (CI) stress threshold (representing the stress level at which new micro cracks begin to form in an intact rock) is widely used to establish the in-situ spalling strength, and is generally regarded as the lower limit of the long-term rock strength. This study analyses the evolution of CI and other mechanical properties for a high-porosity sandstone with an average UCS of 38 MPa under unconfined cyclic compressive loading. The results indicate that rock properties are variably affected by cyclic loading with; no significant effect on Youngs Modulus; a moderate increase in Poisson’s ratio and fracture angle; a moderate decrease in UCS; and a major reduction in the CI stress threshold. All of these changes were generally amplified by cyclic loading at higher stresses. From the results, it is concluded that rockburst and spalling limit in underground structures may reduce over time if the rock is subject to repetitive cyclic loading, and that the reductions will be greater for higher cyclic stresses. This may be a significant factor in the design and operation of some deep underground structures.

Apr 26, 2022

By Rolf Lauten, Yongjun Peng, Yufan Mu

"Biopolymers, produced from cellulosic biomass, have promising prospects of application as depressants in mineral processing. In this study, three different types of biopolymers (i.e., DP-1775, DP-1777 and DP-1778) were used to study the effect of polymer structure on flotation of un-activated pyrite, copper activated pyrite and chalcopyrite. It was found that the depressing effect of DP-1775 and DP-1778 was much stronger than that of DP-1777, and pyrite was depressed to a greater content than chalcopyrite with the same biopolymer at the same dosage. The biopolymer concentration played a vital role in determining the degree of depression. For each biopolymer, the higher the concentration, the greater the minerals were depressed. The mechanism underpinning the depressing effect of these biopolymers was explored in this paper. The concentration of biopolymers could determine the properties of the adsorption layer and the confirmation of biopolymer chains on mineral surfaces. The biopolymer molecules may aggregate when polymer concentration was over a critical value. Molecular weight and functional groups of biopolymers were the key factors characterizing the depressing capability of different biopolymers. Differences between the tested biopolymers and features of the adsorbed layer might account for the observed trends in ability to depress pyrite and chalcopyrite flotation. The greater depressing effect of biopolymers on pyrite over chalcopyrite might result from the preferential adsorption of biopolymers on pyrite over chalcopyrite."

Jan 1, 2014

By Noel N. Moebs

This report summarizes a U.S. Bureau of Mines study on the application of geotechnology to identify and minimize ground control hazards in talc mining operations in northwest Georgia. The major ground control hazard is pillar sloughing attributed to the steeply dipping orientation of a pronounced foliation in the talc ore body. The sloughing problem, which gradually reduces the effective support area of a pillar through attrition, can be minimized by appropriate artificial support, as determined by a rock classification system, and by a more uniform pillar design. A boundary element model confirmed the advantages of using a uniform pillar design to avoid excessive loads on portions of irregular pillars. Instrumentation to measure roof convergence and pillar loading was installed at selected locations in an active talc mine but failed to detect any significant changes, suggesting that the gneiss hanging wall constitutes a strong roof that probably can support large spans between pillars and permit high extraction ratios. This interpretation also is supported by a rock classification of the hanging wall gneiss.

Jan 1, 2010