Search Documents

By Warwick Hoffmann, Robin Batterham, David Conochie

CRA has been actively involved in developing a bacterial oxidation process for the treatment of low grade, refractory gold resources. Success in this application is dependant on the design of large, energy efficient reactors. It was identified at an early stage, that the conventional, bottom sparged bioreactor is inherently inefficient because air must be compressed to a pressure above that at the bottom of the tank. This inefficiency increases as the size of the reactor increases. CRA has developed a novel approach to the aeration problem. In this, venturi aeration is used to aspirate air into a liquor stream. The stream is then reintroduced at the top of a draft tube bioreactor. The advantages found with this technique include · low energy requirements and high oxygen utilisations. From results at the 30 m3 scale, we predict an energy usage of -500 kWh/t sulphur oxidised at a scale of 1000 m3.

Jan 1, 1993

By J. Beddoes

The various microstructural factors that influence the creep resistance of y-titanium aluminides are presented and discussed. Titanium aluminides have potential for a variety of intermediate temperature applications in both gas turbine and reciprocating engines. While it is well established that the 'fully lamellar' titanium aluminide microstructure offers superior creep properties, the particular influence of lamellar morphology, third phase precipitation, and grain boundary structure in controlling both the primary and tertiary creep behaviour is presented. The results are primarily based on tensile creep experiments undertaken using several titanium aluminide intermetallic compositions processed via powder metallurgical techniques, investment casting and Bridgman directional solidification. The results indicate that lamellar structure and precipitate formation have a major impact on primary creep, while microstructural degradation through both lamellar and precipitate coarsening influence on the onset of tertiary creep leading to fracture. The results are used to design a creep resistant microstructure produced by directional solidification and the effectiveness of this designed microstructure is demonstrated through 10,000 hour creep tests.

Jan 1, 2004

By R. D. MacEchern, M. C. Rockwell

"This paper describes the research and tests carried out to recover the readily available barite from the tailings produced by the Nystone Chemical Ltd. operation at Debert, N.S. The tailings comprised 70-80% of the original feed and contained about 20-25% Baso4 .The objective of the research, undertaken during 1982, was to produce a barite concentrate which would meet the American Petroleum Institute (API) barite requirements for use in drilling mud. Samples from the tailings pond were examined and analysed to determine the tailings characteristics.Preliminary test work was performed on the tailings samples using a Haultain Superpanner, Wilfley tables and Humphrey's spirals. The grade of the barite concentrate retrieved did not satisfy the API barite requirements.The fineness of the tailings and the fact that approximately 80% of the barite was contained in the -200 mesh (0.074 mm) size fractions, indicated that flotation of barite from the tailings might be successful."

Jan 1, 1984

By Lindsay A. Robertson

The long term management of acid generating tailings at mine closure is a common issue, however, management of ARD is significantly impacted by local conditions, including climate. Acid generating tailings, over time, will produce acid rock drainage (ARD) if left exposed to water and air, which both contribute to the sulphide oxidation process. The long term closure of tailings storage areas is a concern from both environmental and engineering perspectives, with long term acid generation and dam stability the main risks. Several approaches can be taken to minimize ARD from tailings facilities using cover systems. Three tailings facility cover case histories, in areas of net positive water balances, were investigated using unsaturated flow modelling software to determine the long term potential for limiting ARD by increasing saturation of the tailings and decreasing oxygen ingress. Each case study demonstrates the importance of integrating the tailings dam engineering into tailings cover closure design. Model predictions are compared to measured saturation levels to assess the accuracy of the calculations.

May 1, 2011

By R. A. Lohnes, S. M. Levorson

As part of research to develop a coal handleability index that predicts the ease with which coal will flow through a handling system, comparative tests were conducted with a Johanson Indicizer and a low-stress triaxial apparatus on 12 coals at a variety of gradations and moisture contents. The lndicizer test provides a rapid method for generating data associated with coal handling characteristics. The arching index measured with the Indicizer is a function of the geometry of the apparatus as well as the properties of the coal. The handleability index determined from triaxial data is a more direct measure of coal characteristics. The handleability index shows a wider range of values than the arching index and, therefore, appears to be more sensitive to coal variations. Neither the arching index nor the ratholing index, as measured with the Indicizer, agreed well with the handleability index. This is attributed to differences in sample preparation as well as to the tests themselves.

Jan 1, 1993

By Sun Jiale

This paper presents a brief description of information construction technology for supported excavation to assure satisfactory performance of engineered system. As a successful example of application of the technique, quite a few troublesome problems, such as high groundwater level in soft ground and crowded buildings around the excavation, were solved satisfactorily in the construction of the new tower of Guangzhou Overseas Chinese Manison.

Jan 1, 1991

By Ed O'Connor, Per-Anders Persson, Manhong Zhou

This chapter deals with the concepts of shock waves and detonation waves together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the context of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of an explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of this chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1997

By Peter K. Eriksson

Nanofiltration is very efficient in separating heavy metals from water solutions, even if they contain strong acids. Desalination System, Inc., has many years of experience in this area, and this paper deals with three different such cases. The first case deals with concentrating the heavy metals in the pregnant leach solution from a copper dump leaching site with a surplus water problem. The increased copper concentration in the pregnant leach solution increases the capacity of the following copper extraction stage. The nanofIltration permeate is polished with a biomass adsorption column to remove the small amounts of remaining heavy metals, before being discharged. This method eliminates sludge handling and disposal, which are quite costly with the alternative precipitation process. In the second case, a complicated precipitation method was used to remove heavy metals from the waste stream of a specialty metals manufacturer. Nanofiltration was installed to increase the metals concentration four times, which greatly simplified the precipitation process. The chemical consumption and sludge production decreased by more than 80 percent, and the labor cost decreased by 66 percent. In the third case, nanofiltration was used to purify waste sulfuric acid solutions containing heavy metals, to meet the specifications for technical grade acid. Sulfuric acid concentrations above 30 weight percent were successfully purified in a multiple pass membrane system.

Jan 1, 1996

By D. Sohn

Work accidents have an essential impact on the economy of a country and in final consequence on each company. The main purpose of industrial OHS is to maintain and promote the health of all employees. Healthy working conditions increase efficiency and motivation and safeguard the success of the business against the background of the extremely dynamic processes of change. Maintaining and promoting the health of all employees, weather in operation, administration or on the mining site, has become therefore not only an ethical requirement but also an economic must. Creating a suitable working environment for people today entails much more than just preventing accidents and work-related illnesses. It is important to be proactive in establishing an even better culture of prevention and to convince everyone, workers and managers alike, of its importance. Especially in the age of rapid changes and above all in view of global competition we are more dependent than ever on healthy, enthusiastic, competent and creative employees. OHS provides you with the necessary competitive edge.

Jan 1, 2007

By R. V. Ramani, T. V. Falkie, T. E. Wilson

In order to increase the efficiency of underground coal operations, it is necessary to understand not only the operating system in detail, but the interrelationships between system components and the operating environment. With such an understanding comes more exact application of simulation and other operations-research techniques to plan and operate mining systems. One aspect of the coal-winning system in need of better definition, namely, the performance of continuous miners, is dealt with in this paper. Detailed discussion of this research will be found in a report by the authors. Mining Rate The performance of continuous miners-that is, the rate at which miners can deliver coal from an underground face to the outby transportation system-is dependent upon the geometric and geological conditions of mining, the characteristics of the mining machinery, and the skill of the machine operators. In order to predict mining performance, it is necessary first to identify these factors, secondly to devise a data-collection technique, and lastly, to select a method of data analysis for drawing meaningful conclusions. Factors Affecting Mining Rate: The factors that affect the mining rate can be conveniently grouped in the following four categories: Geological Factors-The natural conditions such as seam thickness, hardness, and cleavage. Geometrical Factors-The height and width of the entries and the angle of drivage with respect to the main entries. Machine Factors-The mechanical characteristics and physical dimensions of the machine, condition of the machine, condition of the bits, and related items. Other Factors-Operator efficiency, size consist of cutter product, etc. A classification such as given here is not rigid; some of the factors can be included in more than one of the categories and some can be combined as ratios. Data Collection The empirical nature of this investigation required measurements of variables under operating conditions in underground coal mines. A majority of the variables measured were continuous over a specific range of values; for example, the "width ratio" varied in practice from 0.25 to 1.00. "Dummy" values were assigned to certain operational variables in order that the variables would have numerical expression, i.e.: [ ] Data Analysis The method of analysis was to test a large model containing potentially significant variables and then reduce the model to one containing only the essential significant variables. The procedure of "scanning" a large proposed model and subsequently condensing the model consisted of two cycles of the same series of computational procedures. Correlation analysis, factor analysis, and regression analysis were the three statistical procedures that were used to derive the rate-generating equation. Correlation and Regression Analysis: Multiple linear correlation coefficients between all of the variables were calculated using the Pearson product moment formula along with the statistical significance of the correlation

Jan 1, 1975

By J. A. Dos Santos

High angle conveyor (HAC®) systems in open pit mining offer many advantages over the traditional, truck only, haulage systems, including: (1) superior energy efficiency, (2) less dependency on petroleum products, (3) less sensitivity to inflation, (4) less labor, (5) less excavation for the amount of ore recovered, and (6) less ramp construction and maintenance costs. Previous studies had revealed the technical and economic feasibility of high angle conveyors. This paper presents the Sandwich Belt HAC® as the vital link to optimization of in-pit conveying systems. HAC development to date is discussed, beginning with studies in 1979, to the first large scale prototype in 1983, to the first commercial unit in 1984, into "the latest commercial installations. Discussion continues with the HAC systems to suit the various open pit mining operations and the corresponding characteristics of the system components, particularly the high angle conveyor. The range of HAC systems from the low capacity (up to 1,814 t/h), low lift (10.7 to 36.6M), highly mobile to the moderate capacity (1,814 to 3,629 t/h), moderate lift (36.6 to 76.2M), intermittently mobile to the high capacity (greater than 3,629 t/h), high lift (greater than 76.2M), semi-mobile, are discussed along with some possible combinations of these.

Jan 1, 1989

By M. Geoghegan

Under the provisions of the U.N. Law of the Sea Convention Ireland is likely to have mineral rights to an area of continental shelf some six times its present land area. Apart from the major potential hydrocarbon basins which are currently the focus of active commercial exploration, little is known about the mineral resources of this vast area. In recent years a variety of mineral resources however have been identified from the coastal region. These include Sand and Gravel aggregates, Calcaraeous Algae (Lithothamnion), Heavy Mineral Sands and Coal deposits. The potential also exists in the coastal zone for buried placer deposits and base metal deposits. Several million cubic metres of gravel and hundreds of millions of cubic metres of sand have been identified by the Geological Survey of Irelands (G.S.I) Marine Unit off the east coast. The greater part of these deposits lies within the 10 metre depth contour and are easily recoverable. Irish aggregate needs at present are well supplied by onshore Pleistocene glacial deposits. Commercial interest in offshore deposits is in supplying coastal areas which are locally poor in aggregate and major coastal construction works. The possibility of supplying the large British and Continental European Market nearby also exists.

Jan 1, 1988

By J. B. Littlefield

The term "konimeter" is used generally to designate a type of dust-sampling instrument that collects the dust from a small volume of air by impingement on a glass plate prepared aced with an adhesive film. The konimeter was first developed by Sir R. N. Kotze about 20 years ago and was followed a few years later by the circular-type konimeter, by which a number of samples may be collected on a glass disk. The present discussion will be confined to the circular type, as it is used most. Various techniques have been developed for using the konimeter, and many materials, such as petrolatum, mineral oil, and glycerine jelly, have been used in preparing the adhesive film. In South Africa, Australia, and Canada, where the konimeter has been employed most widely, dust samples are treated by ignition and washing before being counted. In Canada the dust samples are collected on a disk of special heat-resistant glass prepared with a film of mineral oil; the disk is then heated to a dull cherry-red in a muffle-furnace to remove the film and organic matter, cooled, and washed with a few drops of 50-percent hydrochloric acid followed by distilled water and alcohol, and then heated again to remove residue left by evaporation of the alcohol. After this treatment, the dust samples are counted under a magnification of 150 diameters with dark field illumination.

Jan 1, 1938

Miners really are an optimistic bunch. Even with the dark clouds hanging over the global industry, mining professionals still turn out in droves at industry conferences. In February, more than 7,200 professionals attended SME?s Annual Meeting in Denver, CO, a record. And the following week, more than 30,000 people converged on Toronto, ON, Canada for the Prospectors and Developers Association of Canada (PDAC) meeting. For many small and junior mining and exploration companies the PDAC conference is a place to find potential investors in their projects. The Investors Exchange attracts several hundred companies, each showing off their properties to the many money types who wander the hall during the four-day conference.

Jan 1, 2013

By Xiangze Shu, Yuzhong Xing

All programs used to optimize main fan nowdays have to be run on the large and medium- sized computers. With a lot of array elements, complex processes, low convergence speed and large storage, these programs are both time consuming and difficult to be used in the micro computer. This program uses two languages (dBASEIII and BASICA) to calculate the network and to choose the fan respectively. It allows user to compare and choose the parameters of various kinds of fan and to transfer the selected fan parameters to the master program by a data communication system. Then the user can get the air quantity, the air pressure, the power and the efficiency of the main fan. The advantages of this program arc as follows: 1. It can be run on IBM-PC or compatible micro computer. 2. It can select a fan more quickly and less time consumingly. 3. It can choose desired one or a set of fans according to user's requirements. 4. It is suitable for the research institutions and coal mines.

Jan 1, 1991

By Andrew Budek

Reinforced concrete piles are used to carry foundation loads through considerable depths of soil to provide superstructure stability under gravity loads and lateral forces. The creation of cast-in-place (or cast-in-drilled-hole, i.e., CIDH) piles begins with the auger-drilling of a hole of the appropriate depth, into which a cage of reinforcing steel is placed (the cage length is generally equal to the depth of the hole, a construction joint being used to connect the in-ground pile with the superstructure). The pile is then finished by casting with concrete, and the superstructure then appended. The superstructure may either be a column (denoting the structure a pile-column), a column and cap beam, or a footing. Typical pile-column configurations are shown in Fig. 1 (a CIDH pile used in a footing would be similar in overall configuration to Fig. 1(b), with H=0). CIDH piles are well-suited for alluvial soil profiles with a deep water table; such conditions generally allow the auguring of a clean and regular hole.

Jan 1, 2007

By G. A. Kosick, L. Kuehn

The design of an information management system (IMS) for a mineral processing plant requires prior consideration of many factors, which can be broadly categorized into two domains, process plant considerations and IMS considerations. The process plant considerations include: plant characteristics, management and personnel issues, existing organizational standards and policies, and the level of existing hardware and software systems. The IMS considerations include: system functionality, system sizing and desired performance, hardware components, software components, and system support issues. All of these aspects must be addressed in order to achieve a functionally successful and cost effective system. The purpose of this paper is to lay out these design issues and, in doing so, to provide process engineers with a guideline with which to tailor a system that is best suited to their specific application. The paper is completed by presenting an approach that has been used in two Canadian concentrators. Both of these plants have incorporated MillEX, a software system designed specifically as the central component of a mineral processing IMS.

Jan 1, 1993

By C. S. Smith

QUANTITATIVE methods were used to good effect in the earliest days of metallography1-3 but they mysteriously passed into virtual disuse until the important paper4 by Howard and Cohen in 1947. Various devices for the measurements of integrated linear intercepts have been constructed, primarily by petrographers. The hydraulically operated stage designed by the writer5 was satisfactory, but prolonged use caused air bubbles to become entrapped, which introduced back-lash. A new stage has been constructed which avoids this defect and provides better integration when measuring directional structures. This utilizes a circular traverse, and integration is achieved by counting electrical pulses produced by a photocell and a light chopper.* The stage is shown diagramatically in Fig. 1 and in photograph, Fig. 2. It is of simple construction. Mounted on a plate with clamps to fit the stage of a standard metallurgical microscope is a worm and 100-tooth worm gear, the latter supporting the specimen to be measured. The worm is manually actuated by a knob which contains inside it three

Jan 1, 1961

By J. E. Hoffman, Massimo Maccagni, T. J. Keefe, Marco Olper, O&apos

The problem relating to the use of insoluble anodes in acidic and highly aggressive environments has still not been definitely solved, and it is therefore a recurring subject of discussion. The fields of application in which insoluble anodes play a fundamental role are mainly in the electrolytic extraction of metals, in cathodic protection with impressed current, and in the production of oxidized halogenated salts. Based on the foregoing, B.U.S Engitec Servizi Ambientali (BESA) developed an electrode suitable for the use in the above-mentioned system. The basic component of the BESA anode is a bimetallic wire made of a copper rod (core) covered by a thin layer of valve metal, to be chosen between tantalum (Ta) and niobium (Nb). The wires, coated with suitable catalyst (PbO2, Pt or others) are inserted in a plastic frame and fixed to a current feeder by means of a screw, ensuring an optimal contact. Experimental data on the operating conditions, such as kind of electrolyte, current density, electrode potential, corrosion tests and fields of possible application, are described.

Jan 1, 1993

By Charles E. Johnston

By substituting photoelectric automatic car loading for mechanically induced hydraulic automatic loading and by protecting the process against operational failures, the engineering staff at International Minerals & Chemical Corp.'s Carlsbad potash mine has developed a reliable loading process that operates without an attendant. The photoelectric control, developed primarily because of frequent failures in the hydraulic control system, has not changed the basic loading operation and physical layout. Mine-run ore ranging in size from minus 200 mesh to 30-in. lumps is dumped onto a conveyor belt which discharges into a so-called "flop gate chute" which in turn, feeds the ore into six-ton capacity mine cars. Each car is filled progressively by moving the entire trip forward. When a car is filled 12 in. above its rim, the direction of flow into the car is reversed 180º and filling of the next car back is begun while the entire trip is moved forward again. Once the next car is properly spotted under the front chute, the flow is again directed to the forward position.

Jan 9, 1962