Search Documents

By Charles Fulton

EXPERIMENTAL work on the process was begun on a laboratory scale at Cleveland, Ohio, in 1914, and transferred to East St. Louis, Ill. in 1916, where a commercial sized furnace was in technical operation until January, 1918. The essential steps of the process are as follows: Oxidized zinc ore or roasted zinc concentrate is mixed with crushed coke and coal-tar pitch and formed into briquets 9.25 in. (23.5 cm.) in diameter and 21 in. (53 cm.) long in a manner similar to that used in the manufacture of graphite or carbon electrodes, except that much less care and time are required. The composition varies with the nature of the ore; in one case, the composition was 100 parts ore, 70 parts coke, and 18 to 20 parts pitch. These briquets maintain their form and volume during and after the distillation of the zinc. This object is gained by using coke as the matrix and coal-tar pitch as the binder; this pitch becomes coke on heating and unites the ore particle and the original coke particle into a continuous mass. The briquet is an electrical conductor but only to such, a degree that it can be used as a resistor. The size of the ore, as in the present practice of zinc metallurgy, ranges from fine material, such as flotation concentrate, to coarse table and fine jig concentrate. The process is not restricted to any particular kind of ore, but is applicable to pure high-grade ores, ores high in iron, and complex zinc lead ores, since the residue from the distillation is held immovably in place within the briquet. In the case of complex zinc-lead ores, the distillation is conducted with a carefully regulated temperature so that a high percentage of lead is retained in the distilled briquet, which may then be smelted for its lead content. In present zinc smelting practice, the reduction fuel is from 40 to 50 per cent. of the weight of the ore. In the briquet, it is from 60 to 85 per cent. of the ore; but unless the ore is exceptionally high in residue, the distilled briquet

Jan 9, 1919

By H. L. Lovall

Huge banks of preparation plant refuse and other non¬saleable materials have accumulated over the years in all major United States coal producing areas. These banks, esthetically and commercially undesirable, can cause air and water pollution and land reclamation and mineral conservation problems for the industry and nearby communities Although some refuse banks have been reworked to recover saleable coal, all remain and accumulation continues. Even those previously processed continue as potential hazards. Among the several problems created by refuse banks, in situ combustion is most treacherous. Of the millions of tons of major accumulations, there are at least 450 refuse banks on, fire at this time Attempts to extinguish such fires are costly, impractical and generally unfruitful. Studies are in progress to evaluate the potential of processing such materials to eliminate the combustion capability and to yield usable fuel and nonfuel products. Aspects of the study now in. development for coal refuse include: (a) evaluation of characteristics (size, sink-float, ash, sulfur and calorific value) of the coal refuse materials which are known to be highly variable, (b) development of an ignition test having significance for in situ conditions, (c) study of processing capabilities (comminution for liberation, pilot plant washing tests), and (d) investigation of potentially significant properties of fuel and nonfuel products which could be altered to enhance their market potential.. Among the latter products are lightweight aggregate, fill for mine slushing operations, construction, etc: Plans are to extend the studies to include the design, erection, and test processing of refuse with a transportable plant,; which could provide basic economic and product utilization data from several locations

Jan 1, 1964

By J. A. Meech, C. A. Harris

"The application of control theory in mineral processing is more difficult than in other industries because of the complex nature of the unit processes involved and because of problems with accurate on stream measurement of process variables. Conventional control is based on proportional, integral and derivative functions of a continuously measured error term. Computer control can enhance these actions by incorporating logical routines to switch from one relationship to another. The success of this logical approach depends on our understanding of the process dynamics and the stability of the process and model under all conditions. Typically the model does not apply at all times in mineral processing because of frequent and unmeasurable changes in the ore parameters.Recent advances in the theory of fuzzy sets have led to the application of this science to process control. Fuzzy Logic can be used to develop heuristic or rule-of-thumb controllers with the strategy based on the actual operating practice of experienced plant operators. Control action has increased flexibility through the adaptation of human reasoning. Acceptance of the control system by operating personnel is significantly higher because of their participation in its formulation. The requirement of an exact model is not essential.A heuristic controller has been designed and tested with a computer simulation model of a secondary crushing plant. The results of this study are discussed and future applications of this control technique to other mineral processes are suggested. IntroductionThe application of control theory in mineral processing is more difficult than in other industries because of the complex nature of the unit processes involved. Mineral processes typically are characterized by non-linear relationships between input and output variables. Many of these variables cannot be monitored accurately on-stream and so long time lags on the measurement loop are features of the system. The processes, themselves, often have long time-varying responses while the process loads fluctuate significantly on a short-term basis.Attempts to control these processes have led to the formulation of mathematical models to describe each unit activity. Adaptive techniques have also been tried to compensate and account for process changes and vageries. These approaches are mathematically rigorous so that their complexity and precision limit their usefulness when applied to ""vague"" processes."

Jan 1, 1987

By J. R. Cobble

The Federal Bureau of Mines conducted static tests at 2,500° F on 39 refractory compositions, and dynamic tests at [2,825°35° F] on 31 commercial refractory brick specimens to determine their resistance to corrosion and erosion by a slag similar in composition to that used in producing insulating mineral wool. The static tests showed fireclay, low-alumina compositions (<70 percent A1203), zircon, zirconia, SiC, and clay-bonded graphite refractories to be unsuitable. Dynamic test results indicated that magnesia and chromia compositions were superior to high-alumina compositions (=70 percent A1203) as a furnace lining for melting mineral wool. Data from these tests indicated that magnesia and chromia compositions with low RO/R203 mole ratios were more resis tant to attack by mineral wool slags than ones with high RO/R203 mole ratios.

Jan 1, 1975

By R. J. Sheets

"INTRODUCTION What is the primary responsibility for geo-engineers in mining? Early in my career, I was asked this question by an experienced engineer. After explaining some various tasks, I was informed that the main responsibility was to monitor. Although this proved true for many cases, I came to understand that monitoring is merely one means to achieve the primary responsibility of a geo-engineer – ensure the safety of all personnel. The potential for groundwater to impact stability allows this responsibility to be shared with hydrogeologists as well. Inherently, we monitor to identify risks; we analyze designs and develop models to mitigate risks; and we are provided opportunities to explain to supervisors the geo-risks to personnel and mine plans that will result from particular courses of action. A couple years ago, I took an opportunity to share experiences from the first several years of my career as a geotechnical engineer with junior geo-engineering staff within my company. The intent was to share situations that were a part of my development, so they could learn and understand their responsibility to the safety of all personnel. Similarly, the purpose of this paper will be to share these thoughts with new geo-engineers in the industry in order to help prepare them for the challenges they will face. WHAT IS OUR PURPOSE? A senior hydrogeologist shared an experience that occurred in their career. The experienced hydrogeologist had spent some time with the hydrogeology staff, most of them relatively new to the mining industry, to understand how they viewed, and carried out, what they perceived as their responsibility at an active mining operation. After a couple months of observing and mentoring, the senior hydrogeologist met with everyone and posed the question above. I am sure that most junior geo-engineers would start explaining different tasks or projects that they must complete. The list would include monitor groundwater levels, track slope movement, evaluate designs, build models, oversee drilling programs, etc. These individuals did as well their supervisor. After going around the room allowing each individual to answer, the experienced hydrogeologist provided them the real answer to the question: SAFETY. If you examine the root intent of nearly every responsibility geotechnical engineers and hydrogeologists have, it is to apply our professional skills to ensure the safety of our workforce. When the objective of safety from the geotechnical and hydrogeology disciplines is achieved, inherently accomplishing the mine plan should follow suit, or it should significantly minimize the impact by gravity or groundwater. The objective of a hydrogeologist is to ensure the soil or rock around an open pit or underground mine is dewatered; this specific objective will reduce pore pressures which could lead to a possible ground failure. They ensure a working bench/UG level is dry, so operations are not dealing with adverse conditions while mining. A geotechnical engineer is expected to use all available information and engineering judgement to provide design recommendations, so that the mine will not catastrophically fail. Additionally, they will implement the monitoring systems to identify hazards in advance in the event that the design is flawed and people need to be evacuated. We all know that safety is important to everyone; however, our particular set of technical skills play a significant role in ensuring the safety of a large portion of the global mining workforce."

Jan 1, 2018

By R. A. Welsh

The Bureau of Mines has developed a photoelectric concentrator apparatus which is capable of collecting incremental products from the discharge of wet concentrating tables. The instrument uses photoelectric cells as sensors to differentiate between two products which have differences in color or reflectivity. The photocells provide a signal that controls a mobile splitting device that separates the products. Tests conducted on a wet table demonstrated the ability of the apparatus to separate a product containing 81.5 percent pyrite from a lower-grade product containing only 68.8 percent pyrite. The photoelectric concentrator should have a broad application for collecting concentrates with visible color or reflectivity differences from wet concentrating tables.

Jan 1, 1972

By Zong‑yu Li, Shao‑jian Ma, Xiao‑jing Yang, Jin‑lin Yang, Xing‑nan Huo, Heng‑jun Li

Optimizing and adjusting the particle size composition of grinding products is of great significance for improving economic benefits and resource recovery and utilization. In this study, grinding contribution and quantitative separation of impact and grinding mechanism in cylindrical mill were creatively researched, and the grinding technical efficiency of impact and grinding was coupled to the grinding technical efficiency of grinding in drop-off mode. The results showed that the contribution rate of impact and grinding in grinding in drop-off mode varied with the grinding time. On the whole, the contribution rate of impact action increases with the grinding time and gradually becomes stable, and the contribution rate of grinding effect was just the opposite. Under the experimental conditions, the main contribution of the grinding process is impact action, and the contribution of grinding action is auxiliary. In addition, the contribution rate of impact and grinding effect in grinding in drop-off mode was also related to the feed particle size. The contribution rate of impact effect decreased with the decrease of feed particle size, while the contribution rate of grinding increased inversely.

Aug 3, 2023

By Robert H. Richards

If one holds up a prism, or wedge of glass, with narrow angle, say l° to 2O, and compares the transmitted image with the image seen above or below the prism, the former will be found to be thrown to one side by an amount varying with the angle of the wedge. Speaking of the two rays as the direct ray and the bent ray, we may say, that when the bisecting plane of the prism is at right angles to the line of sight, the angle between the direct ray and the bent ray will be constant for any given prism. If now we place a prism or wedge of glass in such a position that it half-covers the objective of a telescope, we shall obtain on looking through it two images of every object seen—one image by the direct ray, which comes through the unaovered half of the objective, the other which comes through the prism, and is the image by the bent ray. The angle of divergence of these two raps will be constant and unalterable, whether the telescope is directed to a near object, with its eye-piece at increased distance from its objective, or upon a &apos; distant object, with eye-piece nearer to the objective. That is to say, if the " throw " or apparent dislocation of the image is one foot in one hundred feet it will be two feet in two hundred, ten feet in a thousand, and so on. The usual form of stadia-telescope has at the focal point of the objective two spider-lines, placed at a definite distance apart and intended, let us say, to represent a throw of one foot in one hundred feet. But as the distance between lines remains the same, while the distance from the objective to the webs diflers with every variation in the distance of observed objects, it follows that the angle between the lines of sight which these two spider-lines define cannot be con stant, but must vary with every increase or decrease of distance be tween the instrument and the object viewed. If in Fig. 1 we represent three positions of the spider-lines by W1, W2, W3, and three objects corresponding to those positions by 01, O2, 0, at near, medium and distant positions, we see at

Jan 1, 1892

By Fun-Den Wang

Rock bolting has become a major method of coal mine roof support because of its effectiveness, economy, and convenience. The polymeric-resin-bonded bolt has generally proved to be more effective than the mechanically anchored bolt, but the higher cost of the resin bolt limits it to applications where the increased support is essential. The low-cost high-early-strength cement grout developed during this project will encourage more widespread use of fully grouted roof bolts provided practical installation techniques can be developed. Laboratory tests of four types were performed on various rapid-set and accelerated cement products to find a material with properties suitable for replacing resins. A proprietary gypsum cement was ultimately used with good success. A field test of the cement grout was made in an operating coal mine. An intersection was bolted in the standard pattern with cement-grouted bolts and instrumented. A nearby resin-grouted intersection was also instrumented and observations were carried out in both intersections for 2 months. No substantial difference was found between the support provided by the cement and the resin.

Jan 1, 1976

By Joseph A. Vanous

The inductive communication system was developed under this contract for use in the hoist of deep mines. This program was a four phase program with experimental dual frequency equipment resulting from Phase I, emergency single frequency equipment developed under Phase II, and equipment documentation required under Phase III. An additional emergency system was provided under Phase IV.

Jan 1, 1976

By A L. Welsh, P S. Newling

Mill operators are entrusted to manage what are normally the largest capital assets on any mine site. Achieving maximum utilisation and lowest costs that drive operating margins are realised by applying well known fundamentals of good housekeeping and proactive (as opposed to reactive) maintenance programmes. Historically, maintenance and operations staff are bought in late during the construction stage and often do not have the time, know how or tools to put in place (let alone train the incumbent staff) a functioning maintenance system before commissioning starts. They then get drawn into a reactive maintenance paradigm as teething problems post commissioning are dealt with and day to day issues envelop the line tradesmen and supervisors. Additionally, even when some semblance of a planned maintenance system is established, it is often the case that over time personnel and cultural issues mask the development of problematic maintenance practices. As has been observed by the authors on many occasions, even when some basic programmed maintenance system is in place, the collection of maintenance data is often inaccurate, incomplete and not subject to analysis. The net result is of course a high incidence of machine failure leading to lower than expected availability, which ultimately translates to lower revenue and higher net maintenance costs. The time taken and the cost to repair a failed machine is always greater than the timely and planned repair of a worn machine.Upon review of a number of processing plants around the world, especially gold and small base metal operations, it is apparent that companies need to implement maintenance systems whereby the operators are not overwhelmed with data and can manage by exception. Inadequate or inaccurate data collection and analysis result in poor decisions being made and misguided actions taken. GR Engineering Services (GRES) has developed a system to enable the custodians of mining plant assets to make more effective and effective use of maintenance data by being able to focus on the indicators of plant deterioration and to programme concurrent maintenance activities to maximise plant availability and utilisation.This paper outlines the structures that can be employed to address the challenges of implementing a proactive asset management system. The best practice strategies described herein have been based on the fundamentals of a sound asset management framework:a phased approach to the development of Asset Management methodology and processeseffective implementation of programmed maintenance routinesmanaging asset condition data collected from various sourcesefficient analysis of asset data and management by exceptioninterfacing asset management data with Computerised Maintenance Management System (CMMS) and Electronic Management Systems (EMS) systemstips to assist with maximising asset performance.CITATION:Welsh, A L and Newling, P S, 2015. Operating strategies for custodians of company assets creating wealth, in Proceedings MetPlant 2015, pp 338–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Wade Edward Speer

The Hiddenite District of Alexander County, NC has produced some of the world?s finest large emeralds since the first one was discovered 134 years ago. In fact, North America?s largest emeralds come from the district, making this one of the continent?s most unique gem deposits. In addition to emeralds, the Hiddenite District is also famous as the discovery site for the rare spodumene mineral hiddenite, first identified in 1881. Nowhere else in the world do these two minerals naturally occur together. The emeralds are a unique color variety of beryl (Al2Be3Si6O18) with trace amounts of Cr+3 and V+3 substituting for Al+3. The hiddenite (LiAlSi2O6) crystals also exhibit emerald green color due to traces of chromium. Consisting of three large deposits and numerous prospects, the district encompasses an area of 10 km2 (4 sq miles) centered on the small town of Hiddenite. Operations at the Adams, Ellis and North American Emerald Mines properties have been productive at irregular intervals since the 1880s. Currently, only the North American Emerald Mines property is being mined on a regular basis. Recent activity there has exposed a 3-hm2 (7.4-acre) pit with depths of 25 m (82 ft) that provides the best exposures of unweathered bedrock seen in the district in more than 120 years. Although no official records exist, public and private data indicate that the production of the entire Hiddenite District from 1880 to 2007 is about 70,000 carats of emerald and 20,000 carats of hiddenite. The bulk of the emeralds came from the North American Emerald Mine property (NAEM, formerly known as the Rist Mine) where sustained mining replaced the previous sporadic prospecting in 2000.

Jan 1, 2009

By R. E. Brewer

Pilot scale flotation tests were conducted with a l?ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pet of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated. The tailings were first water leached at approximately 60? C, and the water-leached tailings, containing approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH&apos; and sodium sulfide addition on gold flotation recovery and redox potentials were examined. Maximum gold flotation recovery, 36 pct, was achieved at pH 8,5 with a sodium sulfide addition of 0.18 Ib/st. Overall gold recovery by leaching and flotation was in the range of 70 to 80 pet.

Jan 1, 1989

By G. P. Demopoulos

The solubilities of calcium sulfate in HCl-CaC1z-H20 solutions up to 100°C were successfully modelled with the aid of OLI software after bringing proper modification to it. Modelling, more specifically, was carried out with the help of the Environmental Simulation Program, V-6.6.0.4 (www.olisystems.com). New model parameters were obtained by regressing the solubility data. A private databank was established by adding the newly defined model parameters and the calcium sulfate hemihydrate phase that is not included in the original OLI database. The McGill-modified OLI software was successfully applied not only to modelling solubilities but also the transformation of the various CaS04 phases, namely dihydrate, hemihydrate and anhydrite. In this paper, the modelling methodology will be discussed along with a comparison of the capabilities of the newly developed model vs the original OLI model.

Jan 1, 2005

By Changshou Sun

The geotechnical properties of mining zones at Leeville Underground mine (or simply called Leeville mine through this paper) are different from one zone to another. The typical ground condition is poor to very poor. Therefore, an appropriate ground control practice is the key for the successful and smooth ore production at Leeville mine. Based on the available geotechnical data, the empirical and numerical methods are used to design the right ground support systems. The main ground control practice at Leeville mine includes geotechnical data collection, evaluation of the stiffness of the support system, selection of rock bolt types, design bolt length and bolting patterns, development of the ground support standards, and performance of quality controls on bolt installation to ensure proper rock anchorage, and strength of shotcrete and backfill. Through all these activities, an appropriate ground support system has been established and applied at Leeville mine for the past four years. So far, a good result related to successful ground control and smooth ore production has been achieved, although the system is still being improved. The authors of this paper will summarize the ground control practice conducted in the last four years and will discuss the procedures and standards of establishing the appropriate ground support systems for Leeville mine.

Jan 1, 2013

By Stanko Nikolic

One of the keys to success in process development is incremental scale-up, allowing for potential problems to be identified and rectified. The ISASMELT™top submerged lance (TSL) process was developed to maturity using this method by Mount Isa Mines, now owned by Glencore. Commercialization only occurred once the process had been proven on each scale and as a result the ISASMELT™ technology now operates successfully around the world. An important parameter in the evolution of the technology has been the furnace campaign life. The initial commercial scale furnaces had minimal water-cooling. Although this led to shorter campaign lives, an extended development program resulted in the achievement of four-year campaign lives, without any water cooling. In tandem to the refractory designs Glencore Technology, supplier of the TSL technology, has progressed cooled copper lining designs for application to both the ISASMELT™ and ISACONVERT™ furnaces allowing for ultimate flexibility in the lining choice. This allows each ISASMELT™ operating site to minimize their overall life-cycle costs by balancing their campaign life with lining costs, energy inputs, and other shutdown requirements.

By V. Estrada, G. Aguilera

"Since the most of mineral processing are wet, and for more specific applications where it is necessary to increase the purity through leaching and / or concentration, the proper dispersion is the first, and perhaps more crucial stage in the whole chain of processing. This specific process is based on the formation of a dispersion or suspension of mineral, trying to make the mixture as homogeneous as possible, and with specific rheological conditions. Sometimes it is not enough agitation to make it happen, so that chemical additives are used as an aid. However, the addition of chemicals strongly alters the viscosity and other rheological properties of the suspension factor to consider for subsequent steps to ore beneficiation. In other hand, in a process where no chemicals used often employ large quantities of water to achieve dispersion. But if an efficient chemical agent, which optimizes said dispersion through a specific physicochemical effect on the particle surface is used, also it can generate rheological advantages, besides achieving rational use of water and increase the recoveries of the product main about also optimal costs. The aim of this work is to find the optimal rheological conditions for a dispersion of kaolin as study case, looking for stability, best disaggregation, viscosity and pseudoplasticity.To find the optimal additive, the evaluation parameters were: 1) Best degree of dispersion of the suspensions according to the analysis of the flow curve; 2) Best level of disaggregation of particle chemical analysis delaminated by Particle Size Distribution; and 3) Best thixotropic rheological parameters and pseudoplasticity. Finally the optimum additive as one that meets the best combination of parameters is proposed.INTRODUCTIONKaolin is a clay material formed by altering of feldspar composed mainly for kaolinite. Depending on the application, the kaolin as raw material must be refined and processed because the ores of clays contain usually a lot of impurities derived of its sedimentary source, such as feldspar, mica and quartz (Torres, et. al., 2011). According to the experience on the plant floor and the publication of several scientific papers, it is known that the dispersion is a crucial stage in mineral processing (Greene, Duke, & Hunter, 1965) (Raghavan, et. al., 2004), not only because of the disaggregation of particles, besides because of the humectation of them. Is clear that disaggregation of particles give to the suspensions rheological stability, and the humectation improves the effect of further processes like grinding or chemical treatment. The dispersion process involves making a suspension of the mineral with a solvent which is usually water, to obtain a homogeneous dispersion, with the aid of energy of stirring. Sometimes is not enough the agitation (even with high energy) for this to occur, so is necessary the use of dispersing substances which introduce ions and molecules as modifiers of chemical potential, forcing the molecules of the material to disperse. Sometimes their use even could affect the pH of the suspension in a non-desirable condition. (Flores, 2013)."

Jan 1, 2016

By C Young

In the vast expanse of Western Australia’s mining sector, a critical issue has come to light: many mining operations overlook the power of a Broad-Brush Risk Assessment (BBRA) to uncover their critical risks. This oversight has led to a cascade of challenges, where some mining endeavours find themselves grappling with: - Unidentified and unmanaged fatal risks, casting a shadow of uncertainty and heightened compliance risks. - A bewildering landscape where the concept of critical risks remains enigmatic, with some mistaking the risk register for the BBRA. - A fog of confusion surrounding the guardianship of these critical risks, leaving safety responsibilities blurred and undefined. Yet, the solution lies within our grasp. An effective BBRA empowers organisations to: - Pinpoint with unwavering certainty every ‘true’ critical risk. - Clarify ownership for each critical risk, ensuring accountability and swift action. - Create a prioritised roster of critical risks, illuminating the path to safer operations. - Lay the foundation for essential follow-up actions like bow-tie analysis, the identification of critical controls, and the fortification of the safety and health management system. Join us in this presentation, where we delve into the heart of an industry-leading BBRA process. Discover practical insights that will enable your organisation to craft and implement BBRA strategies, bridging the gaps in your journey toward preventing fatalities and fortifying safety protocols.

Apr 16, 2024

By Laszlo Valentyik

The wide scale acceptance of the heavy media separation is due to its simplicity and efficiency. The two most important variables of the process are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media solids. The almost always present clay in the feed and conse¬quently in the medium acts as a stabilizing agent, and its optimum concentration varied between 3-4%.(1,2) Since polymers essentially perform the same function in oil well drilling muds - i.e. to suspend cuttings during drilling - as the fine clay in heavy media separation, this led to the investigation of whether polymers could be used in heavy media separation as supporting agents. During the first phase of the work, it was found that by the controlled addition of polymers, the stability of the heavy media increased without unduly increasing viscosity of the suspensions, thus yielding conditions for more effective and efficient separation. The results of the experiments were reported in a paper at the AIME Centennial Annual Meeting, March 1971.(3) This paper presents the results of the experiment carried out during the second phase of the work.

Jan 1, 1975

By C. Díaz, M. Barati

Prof. Torstein Utigard&apos;s untimely death, in the spring of 2012, put an abrupt end to a meritorious career in the field of high temperature chemical process metallurgy. As an academic in the Department of Materials Science and Engineering of the University of Toronto, Torstein made solid contributions to the advancement of knowledge pertaining to production and refining of both nonferrous and light metals, and to the development of inquisitive and innovative young people in extractive metallurgy. In this profile, the authors highlight aspects of Torstein&apos;s rich personality and of his contributions to his field of expertise.

Jan 1, 2015