Search Documents

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

On Feb. 16, 2012, the Polish coal mining company Lubelski Wegiel Bogdanka S.A. set the world record for daily production from a plow-equipped longwall, with an output of 24.4 kt (26,900 st) of coal from a single face. The company commissioned the first Cat longwall system at its Bogdanka Mine, near Lublin in eastern Poland, in March 2010 and within six months had raised the bar to nearly 17 kt/d (18,700 stpd) of cut coal. Since then, Bogdanka has continued to increase its daily output with a plow face that began mining in the new 7/VII/385 panel last October, taking the world record to new levels. In addition to the record output achievement, the plow face advanced more than 27 m (89 ft) at a 1.63-m- (5.3-ft-) cutting height. ?We thought this achievement would be impossible for any shearer in seam heights as low as this,? said Zbigniew Stopa, vice president of Bogdanka.

Jan 1, 2012

By Carla L. Zenti

In recent years, considerable advances have taken place worldwide in the design and construction of first tunnel linings. With these advances, there is a tendency to move away from traditional support that includes heavy open profiles of rolled steel arches, to a lighter solution with the use of an optimized tubular steel cross section rib, and shotcrete reinforced with steel mesh and/or steel fibers, providing a continuous support (Lunardi, 1982). The development of tubular ribs has provided greater design options, increasing flexibility to engineers and contractors while providing a efficient and cost effective construction method. In this article, the authors describe numerical and experimental investigation on this problem, suggesting as a new first lining steel arch design approach by using tubular ribs cross section as new technical solution for first lining underground support.

Jan 1, 2012

By E. A. Hopkin

Laboratory tests conducted by the author. together with actual field experience in Canada. have indicated the magnitudc of some of the factors affecting ability of drilling mud to clean the hole. A correlation was observed between funnel viscosity and particle slip velocity. A relationship was also observed between the Bingham yield value of the mud and the particle .slip velocity. Laburatury tests indicated little change in slip velocity with funnel viscosities up to ahout 80 sec/qt or to yield values of aboul 15 lb/100 .sq ft. The lip velocity of the partic1e.s. studied vuried from 160 ft/min with water to neerly zero for high mud viscositie. lncreasing the mud density, creating laminar annular mud flow or rotating the drill pipe Mlay also improve the carrying capacity of mud. Field tests indicated that during fast upper-hole drilling, the rate of cutting removal must he sufficien to maintain the concentration of cuttings in the annulus at less than 5 percent by volume to prevernt balled-up drill collars and .stuck drill pipe. INTRODUCTION In the Mid-Continent area, hole cleaning during rotary drilling normally involves the use of low-density drilling muds with funnel viscosities varying from 26 to 80 sec/qt. However, frequently it is necessary to raise the mud viscosity in excess of 200 sec/qt to clean the hole. In addition, field experience has indicated that during very fast upper-hole drilling, annular mud velocities considerably in excess of the maximum slip velocity of the cuttings (normally considered to be 120 to 150 ft/min) are necessary to prevent balling the bit and drill collars. In view of these variations in mud properties and circulation rates necessary to clean the wellbore, a study of factors affecting hole cleaning and the relative magnitude of each was undertaken. The study was also prompted by the knowledge that a drilling mud with properties close to those of water would drill at rates several times that of a viscous mud. The carrying capacity of these near-water muds was not clearly understood, however, and many drillers were reluctant to use them. DISCUSSION EFFECT OF MUD PROPERTIES ON DRILLING RATE The effect of mud properties on drilling rate has been studied by a number of investigators. 1t is clear from their work that mud properties close to those of water will significantly improve drilling rate and bit life. If the water-type mud will also effectively clean the hole and cause no logging or formation impairment problems, the choice of an appropriate drilling fluid is clear—use water. Often, however, a water-type drilling fluid is not capable of effectively cleaning the hole. THEORY OF PARTICLE SETTLING The forces acting on a particle that is allowed to settle through a fluid quickly reach equilibrium, and the particle settles at some constant velocity referred to as the slip velocity. The slip velocity of any particle depends upon a number of factors such as density and viscosity of the fluid, the volume, specific gravity, shape and roughness of the particle, and upon the shape and area of the projected face of the particle at right angles to the direction of relative fluid solid movement. Brown' expressed this relationship for spheres in Newtonian fluids in the following equation. where v, = slip velocity D, — diameter of sphere p, = density of spheye p, = density of liquid /a = friction factor g = constant. The friction factor f, varies as the size, shape, surface roughness and slip velocity of the body, and as the density and viscosity of the fluid varies. WaddelV ound experimentally that where dynamic similarity exists. f, was a function of the particle Reynolds number (NRe) of the sphere (Fig. 1). Fig. 1 shows that f, for spheres varies from over 10 for low NKe numbers to 0.44 for N,,. over 600.

By P. S. Jacobsen

In 1960 over 93 percent of the coal cleaned mechanically in the United States was cleaned in processes that utilized water or dense-medium suspensions of fine solids in water. Thus, in the process of removing deleterious ash-forming and sulfur-bearing minerals, another deleterious substance--water-- is added to the coal. The subsequent removal of the water from the coal, and the concomitant recovery of the coal from the water, is not troublesome in the sizes coarser than 1/4-inch. In the finer sizes, however, it is a difficult procedure that often costs more than the original washing operation. Because of the importance of liquid-solids separation in coal preparation, the Bureau of Mines has a continuing program of research in this field. The objective is to make available information on the performance characteristics of various types of equipment available for liquid-solids separations, thus promoting the wise selection of equipment for specific applications, and, thereby, more effective processing of coal. Results of work on flocculation as an aid to filtration5 and the sieve bend screen6 have been published. The present investigation of the screw-type classifier operating in combination with the cyclone was undertaken primarily because such classifiers are comparatively new to coal preparation and information on their performance is not available. The cyclone has become well-known since its introduction in this country by the Bureau of Mines in 1948.7 Use of the cyclone in conjunction with the screw-type classifier represents an attempt to provide the maximum recovery of solids at minimum moisture content.

Jan 1, 1962

By Joseph Hirschi, Behrooz Abbasi, Harrold Gurley, Yoginder P. Chugh

"The research goal was to assess if analytical tool/s can be developed to quantify displacements around a geological fault as longwall face moves toward it and past it. A company was faced with crossing a 2-3 m (6-10 ft.) normal up-thrown fault in the development entries and the face while mining a 375 m (1,200 ft.) wide longwall face. A field monitoring and numerical modeling study was performed to develop data. Field measurements consisted of roof-to-floor convergence and rectangular rosettes in the immediate roof. Numerical modeling consisted of constructing a 3-D structural model using the FLAC3D software with the fault plane incorporated as ubiquitous joint. Based on analyses and field observations data, the coal company was informed of impending movements along the fault plane and likely impacts on the development entries. Additional stiff supports were installed in head gate entries around the stage loader and equipment about 60 m (200 ft.) outby of the longwall face (solid). As the longwall face approached the fault, predicted displacements were documented and manifested by severe loading on the installed supports.BACKGROUND AND STUDY OVERVIEWThis paper summarizes results of a cooperative study aimed at improving longwall mining operations in Illinois. More specifically, the study focused on: 1) In-mine measurements in development entries while mining ahead of and behind a faulted zone, 2) Making observations on stability of pillars and entries while mining through the fault, and 3) Developing simplified analytical structural models using FLAC3D to assess if predictive techniques can be developed to plan mining operations through fault zone. Available data on geometry of the fault with estimates of the cohesion and frictional parameters were used for modeling."

Jan 1, 2015

By I. B. Tulu, M. M. Sears

"In 2015, 40 longwall mines provided nearly 60% of the US coal production from underground mining methods. This represents a substantial, yet gradual increase from just under 50% over the last 5 years. As a result of this increased production share, the percentage of ground fall related fatalities in longwall mines has also increased when compared to all US underground coal mines. Additionally, about 80% of ground fall related fatalities have occurred in areas where the roof was supported. In an attempt to better understand the status quo of current US longwall support practices, a sample of 21 longwall mines were visited, representing about 40% of the currently active longwall mines in 4 of the 5 major US longwall producing regions. The resulting data was obtained from a wide variety of overburden depths, geologic conditions, mining heights, ground conditions, support practices, and gateroad configurations. The data collected is reported using both qualitative and quantitative methods. The results from the research update previous efforts in classifying mining accidents and injuries as well as current support practices. This data provides a necessary background for future research aimed at further reduction of ground fall accidents and injuries. INTRODUCTION Maintaining ground stability in gateroad entries is essential for longwall productivity and safety (Campoli, 2015). In 2015, 148 unintentional roof falls were reported in US longwall mines. About 34% of these resulted in mineworker injuries. Safety considerations not only include injury from roof and rib falls but also egress from the longwall face during an emergency (Mucho et al., 1999). Over the past 30 years, a number of researchers have studied longwall tailgate support performance (Mirabile, 2015). This research aims to take a snapshot of the ground support installed in modern US longwall mines and provide a supplement and update to the overview provided by Barczak (2005). This will provide a framework for future research into improving gateroad support systems. BACKGROUND Large unplanned roof falls at or above the primary support or those impeding travel and/or ventilation must be reported to the Mine Safety and Health Administration (MSHA). Reportable roof falls, normalized based on production in million metric tons, generally relate to the amount of roof exposed during the mining process (Pappas and Mark, 2012) and provide an evidence-based statistical background for this review of current support practices. Figure 1 shows the reportable roof fall rate in US underground longwall mines for the period 2006-2015 (MSHA, 2016). Over the past decade, roof fall rates have shown a gradual decrease with numbers now at a rate nearly half of what was observed just five years ago. However, over the past few years, roof fall rates in US longwall mines appear to have stagnated at levels just over 1 per 2,000,000 tonnes mined."

Jan 1, 2017

By D. C. McIntire

The Homer City Station, jointly owned by New York State Electric and Gas Corporation and Pennsylvania Electric Company is a three unit coal fired station. The first two units were put into commercial operation in 1969; the third unit became commercial in 1977. Units 1 and 2 are subject to the Pennsylvania State Implementation Plan (SIP) emission limit of 3.7 pounds of S02 per million BTU. Unit 3, having started construction later, is subject to the Clean Air Act, New Source Performance Standards emission levels of 1.2 pounds of 50-2 per million BTU.

Jan 1, 1988

By Boleslaw A. Klosinski

Drilling of a pier hole is accompanied with stress releasing in the surrounding soil and often with loosening of soil at the pier base. In effect the drilled piers are more deformable than driven piles of comparable dimension. The bearing performance of a pier may be considerably improved by properly executed base grouting. Various techniques of base grouting are used; many of them were described by Bruce (1986). The grouting devices are often placed within the pier. Alternatively the soil at or under the base is treated by cement or chemical grout. Preloading of the base subsoil by use of a special grouting cell is considered as the most effective way. Treatment of the ground below pier base with cement or chemical grout may be also useful. It may be performed immediately after the pier construction or during service, as a measure for increasing the pier capacity.

Jan 1, 1995

By Andreas Gaich

COMBINED 3D IMAGES _ Highly detailed 3D geometry _ Identification of fine fractures together with a general impression of the situation _ Dealing with unfavourable outcrop geometries

May 1, 2009

By Vasiliki Founta, Andrew J. Whittle

"This paper describes the development of a 3D finite element model for predicting ground movements caused by construction of 7.1 m diameter twin bored tunnels for the Crossrail project in London using Earth Pressure Balance (EPB) machines. The model uses the commercial FE code, Plaxis 3D, to represent the face pressure, conical shield, grouting process and activation of precast segmental concrete lining systems through a set of boundary conditions that advance through the soil mass along a prescribed trajectory. Soil behavior is described using the Mohr-Coulomb soil model with input parameters calibrated from laboratory element tests. The analyses focus on the performance of the EPB tunneling machines in greenfield conditions beneath Hyde Park, where the tunneling occurs within deep layers of relatively uniform London Clay. The model predictions are in good agreement with surface and sub-surface vertical settlements measured at a well-instrumented section, but tend to overestimate the measured lateral displacements towards the tunnel. Ongoing studies are focused on the role of soil behavior and the approximations in FE model predictions of tunnel-induced ground deformations. Introduction Since their introduction in the 1970’s, closed-face Earth Pressure Balance (EPB) machines have become widely used for soft ground tunnel construction. The EPB design relies on a screw conveyor system to regulate the pressure of the excavated soil/spoil within the head chamber and hence control stability at the face of the machine. One of the key design issues in the application of EPB machines is to establish how control parameters, including the advance rate, face pressure and grouting processes (used to compensate for the tail void at the rear of the shield and to infill gaps between the precast lining rings and surrounding soil) affect and/or control the far-field ground movements. For closed-face systems, short-term deformations are associated with ground losses at the face, overcutting and ploughing of the shield and poor control of grouting in the tail void; while long-term deformations can occur due to consolidation and creep within the surrounding soil (and are closely connected to the seepage boundary conditions;e.g., Laver & Soga, 2012). The control parameters for advancing the EPB machine can have a significant effect on the magnitude and distribution of the far-field deformations. Therefore, analyses of the ground response to tunneling require accurate modeling of the soil stratigraphy and constitutive behavior as well as the construction process. Finite element (FE) methods have been used to simulate tunnel construction since the early 1980s, but only a few studies involved three-dimensional modelling of mechanized tunneling (e.g., Finno and Clough 1985; Bernat and Cambou 1999; Swoboda and Abu-Krisha 1999; Dias et.al. 2000; Melis et.al. 2002; Kasper and Meschke 2004; Möller 2006). In order to get a better understanding of the effect of the construction process and soil properties on the development of the ground deformations more comprehensive models of tunnel excavation and tunnel support are required in order to capture the 3D nature of mechanized tunneling and the effect of construction parameters such as advance rate, face and grout pressure."

Jan 1, 2016

By Galen G. Waddell

Several years of rock-burst research conducted by the Federal Bureau of Mines, in cooperation with the mining companies of the Coeur d?Alene Mining District, Idaho, in addition to progress made by others throughout the world, have led to a good understanding of the rock-burst problem. This paper describes conditions which have caused specific bursts, present capabilities of detecting stress buildup and bursts, control methods, and a suggested approach to analyzing any individual mine-burst problem.

Jan 1, 1970

By Forrest T. Moyer

Injury experience in the mineral mining and processing industries during 1968 was slightly improved in the nonfatal-injury record but worse in the fatality record. The resulting frequency rate of all injuries was slightly better, whereas the injury-severity rate retrogressed appreciably from the figure for 1967. Overall operating activity, as measured by man-hours of worktime, was slightly higher in 1968. However, there were several major segments of the mineral industries in which activity was lower owing to reduced demand for mineral products and to several major work stoppages. These statistics comprise the injury and work experience of all personnel engaged in production, exploration, development, maintenance, repair, and force-account construction work, including supervisory and technical personnel, and working partners and owners at mineral-producing and mineral-processing establishments in the United States. Data concerning officeworkers are excluded except for the oil and gas industry for which such information is not separable. All injury rates and totals are calculated from data before rounding. The data for 1968 are preliminary except for the anthracite, coke, petroleum and natural gas, native asphalt, peat, and slag industries, which are final. The figures represent full coverage for all industries except oil and gas for which coverage is not complete, particularly with respect to small companies.

Jan 1, 1970

By Thamyres C. Carvalho, Edemarino A. Hildebrando, Roberto F. Neves, Francisco R. Valenzuela-Diaz

Synthetic clays are an option of materials that can be modified to obtain better and specific properties when compared with natural clays. Although clays are found in nature, they have many disadvantages that limit the use of them, such as existence of impurities, and variations in composition. Therefore, the objective of this work was to obtain synthetic clay/polyester resin nanocomposites. To characterize the clay, we used X-ray Diffraction (XRD), Total Attenuated Reflection Spectroscopy in the Fourier Transform Infrared Region (ATR-FTIR) and Scanning Electron Microscope with Field Emission (FEG-SEM) methods and the nanocomposites were characterized by XRD and mechanical resistance to compression. The results show the purity of the clay and the time of synthesis is an important parameter for its crystallization process. The clay/polyester nanocomposites were obtained and showed an increase in the ductility.

Mar 1, 2018

By Xueqin Li, Xuewei Lv, Yu Zhang, Wenchao He

In order to make full use of the chromium-bearing vanadium titanium magnetite with chromium, a new process of “direct reduction-electric furnace smelting separation” has been developed for recovering the iron, vanadium, titanium and chromium in recent years. In this paper, FactSage, one of the most frequently-used thermodynamic calculation software, was used to calculate the reduction degree of Fe, V and Cr with different n C/nO (mole ratio of carbon and oxygen). It was found that the suitable operating conditions of direct reduction process were n C/nO > 1.07 and T > 1473 K. In addition, the direct reduction experiment of Hongge vanadium titanium magnetite was carried out and the obtained samples after direct reduction were analyzed by XRD and chemical composition. The result shows that the metallization rate of carbon-containing pellet is nearly 90%.

Mar 1, 2018

By Wang Jia, Chai Li-yuan, Zhang Jin-Long, Peng Bing, Zhang Qiang

"Electrolytic manganese dioxide (EMD) residue was mixed with shale and fly ash as the main materials to make solidification/sintering brick for the utilization of the residue from EMD production. The effects of sintering temperature, sintering time, solid waste content and cooling process on its mechanical properties and toxic elements solidification were investigated according to compressive strength and leaching toxicity. The results showed that the calcined residue had capability of solidifying toxic metals and exhibited perfect strength after treated in the optimal parameters of EMD residue below 50%, temperature at 1000-1100°C, time3-5h, and semi-quenched at 600°C1 InstructionSolid clay-brick holds the leading position among building materials for a very long time in China. The traditional technique of making clay-brick has the drawbacks of backward process, simple facilities and single product. Since Chinese Reform and Opening-up, urban-rural construction and real estate have been booming with the rapidly development of national economy and science technology. The problems of ruining fertile land, environment contamination and high energy consumption in the traditional technique of clay-brick making have not been solved yet. On the other hand, more than 7 billion tons of industrial wastes are accumulated over years which occupies over 6.7 million hectares filed and causes serious environmental problems[1-31. Strategy present in ""The Chinese Agenda of the 21st Century"" required the production of wall materials less energy conservation, land saving and waste recycling.Coal gangue[4-9l, fly ash[I0- 13l, sludge from waste water treatment and tailings of gypsum, pyrite, copper mine, high silicon containing iron, asbestos and ects [l4-lSJ are the solid wastes used for brick making around the world. There are two kinds of process for brick making, high temperature sintering and low temperature steam curing[19•201. Although the technology of two brick making made great progress and got widely application in construction field, no precedent for preparing sintering-bricks with EMD residue as materials occurred in China because of its complicated processing technics and lack of sufficient practical experience to guarantee the bricks' quality.In this study, EMD residue was mixed with shale and fly ash as the main materials to make solidification/sintering brick. The effects of sintering temperature, sintering time, solid waste content and cooling process on its mechanical properties and toxic elements solidification were investigated according to compressive strength and leaching toxicity."

Jan 1, 2011

By Colin Lawrence

The Port of New York and New Jersey is one of the most heavily used transportation arteries in the world, handling nearly 40 per-cent of the North Atlantic shipping trade and directly providing nearly 230,000 jobs to the local economy. In 2004, $100 billion worth of consumer goods moved through the port. To accommodate future cargo volumes in the port, which are expected to double over the next decade and possibly quadruple in 40 years, deeper shipping channels are needed to provide access for a new generation of cargo mega-ships with drafts exceeding 13.7-m (45-ft) when loaded. Current channels within the harbor range in depths up to 13.7-m (45-ft), thus preventing carriers from using these larger ships, or requiring significant reductions in cargo to achieve lesser drafts to operate safely within the harbor. As part of the Harbor Deepening Project, the Anchor-age Channel would be deepened to 15.2 m (50 ft) below mean low water (MLW), for a length of 5,790 m (19,000 ft). The New York City Department of Environmental Protection (NYCDEP) owns, operates and maintains two existing water siphons in the harbor. Due to their shallow depth, both existing siphons must be relocated before dredging of the Anchorage Channel can be completed. Tom Costanzo, manager of capital programs for the Port Authority of New York and New Jersey (PANYNJ), says that ?While the re-location of the existing siphons under the Anchorage Channel is vital to the success of the deepening program, it is also a story of cooperation among key agencies at different levels of government resulting in improvements that will benefit the people of this region greatly.?

Jun 1, 2010

By V. R. Manukonda

Selective flocculation of iron ores is extremely sensitive to the type and the amount of soluble salts in pulp solutions. Chemical precipitation of alkaline earth ions combined with ultrasonic treatment deactivates their adverse effects without using any environmentally ill-defined reagents. The manner in which ultrasonic treatment affects starch adsorption on hematite, dissolution of quartz, and selective flocculation process was investigated. Selective flocculation tests were conducted in the presence of up to 400 ppm calcium ion on a quartz-hematite mixture by precipitation as calcium carbonate, and the role that silicate ion generated by ultrasonic treatment plays in achieving the selectivity of separation is discussed.

Jan 1, 1987

By David De Lemos Pires

Mining is essentially a materials management process where materials are classified, excavated, moved to a desired location, processed at a cost and sold for a price hopefully to generate a profit. ?How much is that cost and can it be reduced?? is the age-old question. The requirement for a paradigm shift with regard to materials movement in search of low-cost production has not just happened by chance but, rather, has been driven by agents of change that include mining companies, consultants, governments and equipment suppliers. During the past 100 years of mining, surface mining technology has involved humans with hand tools, humans with machinery and unmanned automated equipment. In the past 50 years, surface mining technology has evolved and now takes the form of trucks and loaders (TL), in-pit-crushing conveying (IPCC) and autonomous haulage equipment (AHS).

Dec 1, 2013

By Sergio N. Monteiro, Artur C. Pereira, Foluke S. Assis, Henry A. Colorado

The fique fiber is an important natural fiber, originally from Colombia where it is used for sacks and crafts while its plant is used to contain slopes. However, few studies were realized with the fiber obtained from the fique plant leaf, its mechanical properties are superior in many aspects in comparison to some other lignocellulosic fibers. This work investigated the toughness behavior of polyester matrix composites reinforced with up to 30% in volume of a fabric made of fique fiber by means of Charpy impact tests. It was found that the addition of fique fabric results in a marked increase in the absorbed energy by the composites. Macroscopic observation of the post-impact specimens and SEM fracture analysis showed that transversal rupture through the fique fabric interface with the polyester matrix is the main mechanism for the remarkable toughness of these composites.

Mar 1, 2017