Search Documents

By Phil D. Newman, Robert J. Pine, Kevin Ross

The Stratoni Operations in northeastern Greece rely on a selective backfill method to exploit high-grade lead-zinc deposits. Underhand cut and fill often results in spans approaching 6-9 m (depending on the mining method employed) and a competent backfill is required to avoid dilution problems. Cement consumption represents a significant mining cost and through improving the control of the backfill batch preparation, the cement content could be greatly reduced without jeopardizing the grade control. A new distribution system was installed and a QAIQC system designed in cooperation with the operators to allow a wide range of backfill recipes, providing cost savings to the mine. A review of possible failure modes and the consequent strength required for the chosen mining method was also completed and indicated potentially significant cement content reductions. The calculations are supported by 12 years of experience at the mines which provides a valuable insight into the applicability of the approach developed.

Jan 1, 2001

By B Hall

The authors have undertaken many independent mine optimisation and operational improvement projects at Australian and international mining operations over the past decade. This work has provided an understanding of the underlying practices responsible for the good long-term performance of some operations, and the failure of others to achieve their objectives. Good long-term performance, and value creation can be achieved through a logical and rigorous process of identifying the optimal mine plan (æThe PlanÆ) that delivers the corporate goals, establishing appropriate performance measures that are aligned with these goals, and ongoing monitoring of compliance with the established targets to ensure the operation reliably achieves The Plan. A number of practical methods have been developed and implemented to assist mining operations deliver their corporate goals. This paper outlines some of these methods, providing some fundamental guidelines that will assist in the establishment, and reliable achievement of The Plan that delivers the corporate goals.

Jan 1, 2006

By David F. Machuca-Mory

Modelling the geometry of a vein is a crucial step in resources estimation. The resulting models are used as mineralization domain boundaries and have a direct impact on the tonnage of estimated resources. Deterministic models are often built using time consuming wireframing techniques usually based on hand interpretation of the drillhole intercepts. Another approach consists in coding the drillhole samples by a function of their distance to the veins contacts. The coding is subsequently used for modelling the vein contacts away from drillholes. This is a more efficient approach and is able to provide a measure of tonnage uncertainty. The use of location-dependent variograms improves the modelling by incorporating local changes in the anisotropy of the vein structure. This combined approach results in more realistic vein models, particularly when the geometry of the vein has been are altered by folding, shearing and other structural processes. The approach is illustrated on a realistic case study.

Oct 1, 2009

By Joseph P. Hodgson

JOSEPH P. HODGSON.-As to ".Safety First," I did not deal with that, but I will say that in 1913, the number of .men killed was nine, and that year the "safety first" program was commenced; the next year, 1914, the number was reduced to five. In 1915, I am pleased to say that the number was reduced to two in the Copper Queen's entire property, and we have none so far this year. THE CHAIRMAN (G. F. G. HERMAN, Bisbee, Ariz.).-I can say, further, that we have from eight to nineteen men per month incapacitated for more than 14 days. Those are classified in this State as serious accidents. The number of men injured has apparently increased, -but that is clue to our improved method of recording and classifying accidents, no matter how slight. C. W. GOODALE, Butte, Mont.-The importance of cooperation among the members of the staff of an industrial organization is well brought out by Mr..Hodgson's paper.

Jan 12, 1916

By Fred N. Kissell, Robert J. Timko

Safe escape from coal mine fires continues to be a concern of the mining industry. The most life-threatening fires occur outby the working sections. Because stoppings always leak some air, an outby fire may in time cause intake escapeways to become contaminated with smoke and toxic gases. Smoke and gas infiltration into intake escapeways can be minimized by raising their air pressure over that of adjacent airways. This can be done by checking off the intake escapeway near the working face. The Bureau of Mines has investigated the use of a parachute stopping as a quick-erect check curtain during mine fires, and the concept has been tested in several mines. In every instance, when a parachute stopping was erected on the section, the intake pressure went up substantially. The pressure-raising effect of the parachute persisted for up to 1200 m (4000 ft) outby. Results indicate that checking off the intake escapeway may serve as a viable way to improve safety during mine fires.

Jan 1, 1991

By J. L. Huiatt, D. G. Foot

The Bureau of Mines devised a direct flotation method for treating low-grade carnallite (KCl*MgC12*6H20) and sylvinite (a mixture of KC1 and NaCl) ores characterized by a high content of water-insoluble impurities. The procedure consists of flocculation-depression of the insoluble slimes; decomposition leach (carnallite only); potash rougher, cleaner, and recleaner flotation; and final product leaching. The technique eliminates the necessity of removing the water-insoluble slimes by mechanical or flotation desliming. Laboratory results demonstrated that the direct flotation procedure, when compared with conventional techniques, yielded equivalent or improved flotation results with equal or less reagent consumptions. The direct flotation method recovered 81.6% of the solid phase KC1 from camallite ore and 79.7% of the KCl from sylvinite ore in final products containing 60.5 and 60.9% K2O, respectively. A flowsheet incorporating the described flotation procedure is presented.

Jan 1, 1983

By John Jonkman

Two major changes occured during the last 5 years in the applications of computers. First, the cost of computer equipment decreased drastically in an era of high inflation. Second, technological breakthroughs in hardware and software have been applied successfully so that the average person can successfully utilize the computer without having to be a computer expert himself. The mining industry has recognized that computing technology has evolved to a point where it can be applied successfully to assist in improving productivity. Since equipment downtime is one of the major reasons for lost production, the Kennecott Minerals Company has developed a comprehensive maintenance information system which now assists the maintenance department in minimizing equipment downtimes. This paper discusses the primary features and functions of this system, the state-of-the-art technology that has been applied, and the benefits that resulted from using this system. Programs to support mobile equipment maintenance scheduling, which currently are under development, are reviewed and a summary of future applications is given.

Jan 1, 1982

It is desirable to have a model, or method, for major project development, which will enable flexible modelling of separation circuits. This ability improves the understanding of circuits and how they should be operated, especially in a design phase, where various options are evaluated and decisions are made on the required number of stages and configuration. This paper describes existing gravity separation circuit modelling theory and concepts, as defined by Holland-Batt1 (separation window, separation efficiency and proportionality of efficiency). The crux of the paperis the application of numerical analysis to fit raw separation data by means of a modified Bézier-Spline. The paper proposes an alternative to the theory developed by Holland-Batt that provides more flexibility in the modelling of separation stages and curves, which include S-shaped curves. The paper proposes a solution to the challenge of continuously extrapolating data, and the first difficulty normally encountered, which is the fitting of an appropriate empirical formula to raw data.

Jan 1, 2007

By Kelvin K. Wu, Daniel S. Mazzei

As a result of the 1972 Buffalo Creek disaster, the Mining Enforcement and Safety Administration (MESA), now the Mine Safety and Health Administration (MSHA) initiated the draft of new federal regulations to deal with the mine waste impoundment and refuse pile problems. Public hearings were held and finally promulgated in October, 1976. As stated in 30 Code of Federal Regulations 77.214-216, the complete engineering design plan which is mandated by the regulations has to be approved by a coal mine health and safety district manager. During the past 18 months MSHA has gained considerable experience through the submission, review, and approval process. This report indicates the procedures, general design criteria and inspection requirements for submission of engineering plans to be approved. In particular, problem areas encountered most frequently by both operators and MSHA will be discussed. Only through diligent efforts by the operators, consultants and government, can we hope to accomplish the common goal to improve the safety of operations.

Jan 1, 1982

By Ennio Bonetti

The technological applications of MgH2 hydrides for hydrogen storage demand the overcoming of some critical issues: an improvement of the reaction kinetics and a reduction of the desorption temperature. The synthesis of nanocrystalline MgH2 by reactive milling and inert gas condensation and a proper metal catalyst addition, constitute recently employed strategies. In the investigation of the hydrogen short and long-range dynamics, sorption kinetics and nanostructure stability, the mechanical spectroscopy offers some specific advantages. In the present research this technique was employed with other experimental approaches (XRD DSC) to investigate relaxational and structural damping processes in nanocrystalline MgH2 with added catalysts (Fe). Time/temperature variation of the dynamic elasticity moduli and mechanical quality factor are correlated to hydrogen anelastic relaxation processes and concomitant structural transformation of MgH2 to Mg associated to long range H diffusion. Results are discussed with reference to microstructural modification strategies able to assist hydrogen release.

Jan 1, 2006

By A. K. Kyllo

The use of Composite Furnace Module cooling systems has been shown to give improved refractory performance in a number of above bath locations in WMC flash furnaces. To test the behaviour of modules in contact with a melt, a set of instrumented modules have been installed in the reaction shaft of a. nickel flash furnace. The location was chosen to provide a suitably harsh environment to ensure rigorous testing, while still allowing relatively easy access for module installation. The modules were continuously monitored to provide information on the module performance, as well as the temperature in the shaft itself. The shaft temperature showed significant transient behaviour, which resulted in heat fluxes through the modules ranging from 10 to 92 kW m-2. The modules were capable of handling the highest heat flux with no risk of the coolant boiling. This paper details the design and operation of the modules over a period of seven weeks.

Jan 1, 1999

By Richard Moldenke

A. E. OUTERBRIDGE, JR., Philadelphia, Pa. (written discussion).¬ The fact that iron castings improve with age has long been known. Many years ago the late Sir Frederick Bramwell, a distinguished engineer, formerly in charge of the metallurgical and gun-making department of the Woolwich Arsenal, England, determined to break up a large number of cast-iron mortars of an obsolete type that had been in stock for years. It was then reported to biro that it was found to be much more difficult to break these old gun castings under the "drop" than it was to break similar gun-castings recently made, under his own supervision; he changed the.. composition of the iron and still found that whenever castings made recently were broken up (on account perhaps of superficial defects) great disparity was observed in apparent strength between the old and new castings. Sir Frederick then made many other comparative tests, such

Jan 4, 1917

By Saburo Shigeno, Kunzo Amano

As shafts and tunnels move deeper levels in underground mining, development planning becomes more complex. The most serious problem is the aggravation of environmental conditions due to the imposition of higher-than-natural temperatures upon exposed strata. Since such a problem is a potential hazard to health, safety, and production, the authors have developed a system of computer-derived ambient-air temperature data for every major point of an underground mine under a given set of conditions. This system is comprised of two subsystems: 1) Ventilation network analysis, 2) Estimation of air - current temperature. The former is based on the Hiramatsu-Oka method, an improvement of the Scott-Hinsley method. The Hiramatsu-Oka method allows fast convergence and consideration of various fan characteristics. The latter subsystem considers heat radiation from strata, and the humidity. In several tests conducted at Besshi and Sazare Mines of Japan, the computer-derived data correlated with actual conditions.

Jan 1, 1969

By C. Ringas

Pipelines are used extensively in industry to convey various products. Internal corrosion of pipelines can lead to perforation and leakage of the product. A growing problem, not often accurately recognized, is internal corrosion of pipelines caused by bacteria. Microbiologically-induced corrosion (MIC) refers to corrosion caused by a variety of micro-organisms. This form of corrosion is not widely recognized in many industries, although it is widespread and causes many corrosion problems in pipelines, both internal and external. Sulphate-reducing bacteria (SRB) are responsible for the bulk of the corrosion problems caused by MIC. Corrosion caused by SRB is found extensively in water pipelines conveying raw, potable and waste water, as well as in pipelines conveying slurries. This problem also occurs in pipelines conveying crude oil. This paper describes internal corrosion problems of slurry pipelines caused by bacteria and outlines mitigation methods to improve slurry pipeline integrity, thereby extending the life of such pipelines.

Jan 1, 2007

By S. Veeramasuneni

The recent nonequilibrium electrophoretic mobility measurements by laser-Doppler electrophoresis coupled with the stability and prevalence of collector colloids in soluble-salt flotation systems suggest that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by heterocoagulation. Previously reported flotation results confirm this surface charge/collector colloid adsorption model. These results also indicate that the sign of the surface charge has a significant effect on the extent of particle dispersion/aggregation. In this regard, the nature of such particle interaction forces at high ionic strengths are examined to improve our understanding of these systems. Atomic force microscopy (AFM) is now being used to directly measure the interaction forces responsible for the stability of these alkali halide aggregates observed in optical microscopy studies. Results from this study indicate that, while repulsive hydration forces exist between similarly charged hydrophilic particles, attractive forces exist between oppositely charged hydrophilic particles in high ionic strength solutions.

Jan 1, 1999

By P. Woo, N. Brodusch, R. Gauvin, H. Demers

For developing new technologies, it is important to characterize the microstructure of materials with high spatial resolution at the nanoscale. To achieve high resolution, field emission scanning electron microscopes (FE-SEM) were developed. These microscopes allow working at low accelerating voltage, below 5 kV, to take advantage of the reduction of the interaction volume with accelerating voltage. Furthermore, their higher gun brightness compared to conventional thermo-electronic emitters, allow a probe size at the nanoscale. At low accelerating voltage, the emission volume of backscatter and secondary electron (SE) of the type II signals approach that of SEI signals. However, it is not enough to reach the highest resolution. A magnetic field above the sample improves the spatial resolution by collecting mostly high-resolution signals. In addition, the energy-filtration of the electron signals allows selecting the type of contrast detected: topographic, compositional, or crystallographic. The development of these new technologies permits to extend the imaging capabilities of the SEM towards new nanoscale applications.

Jan 1, 2014

By Vernon Read

Among the technical problems in AEC's Project Plowshare is the necessity of determining the precise effects of nuclear blasts in all kinds of ground formations. This calls for extensive in-situ sampling with full core recovery. In the exploration drilling that often precedes a new test detonation, the AEC and its contractors have applied both novel and established sampling techniques in many new ways, giving improved core recovery and reduced costs in all subsurface sampling and testing. Unique among these new techniques is one that achieved full recovery and virtually undisturbed samples from near-surface layers of unconsolidated boulder-strewn alluvium. This approach involves a combination of oilfield and mining core drilling equipment. Oilfield heavy drill collars, rotary stabilizers and thick, vibration-reducing oil emulsion drilling mud were used in combination with the precise hydraulic feed control, fast (over 300 rpm) bit rotation, light drilling weight, hard rock core barrels and multi-step diamond bits that are common in mining industry diamond drilling.

Jan 8, 1963

By Tom Shumka

Introduction ?This technique detects 100% of all gear tooth surface indications, providing comprehensive data, and has the ability to size indications accurately. ?The remarkable advantages of ECA technology, is improved inspection capabilities and significant time-savings. ?The advantage of using EMCD is its ability to size indications accurately. ?This technique does not require the gear teeth to be wiped down by hand after cleaning as in MT, LT or UT inspections. (Figure 1) ?This technique will inspect one gear tooth in 30 seconds. ?All of the data can be archived for future comparisons in an electronic report. Methodology ?This technique utilizes Eddy Current Array (ECA) as the principle inspection technique. ?What has been added are specialty scanner probes with multiple coils, a multiplexer and a software package. ?With 2 and 3D dimensional isometric displays, the defect can be seen electronically as it is on the gear tooth surface, thus, reducing the reliance on human interpretation.

May 1, 2011

By L. Kilpinen, K. R. Kay, H. B. Fowler

"FOREWORDThe International Nickel Company of Canada has built four ore concentrating plants since 1950. The fifth and largest is now under construction. In each successive plant, the level and type of instrument control and sophistication of control techniques have increased as experience was gained. The type of control progress is illustrated in Fig. 1.At Frood-Stobie the high degree of instrumentation and the level of control were made possible by the constant evolution of techniques and improved instrument hardware technology. We have established in practice concepts that are sound, although many modifications to instrument sensor types and locations 1-rere often necessary. It is generally true that at other existing Inco mills, it is possible to run ""all manual"" for protracted lengths of time because of operator availability and dependence. The Frood-Stobie Mill is the exception, and it is the degree of reliability of the instrumentation hardware and level of maintenance that has made this possible."

Jan 1, 1971

By N. Solak

CrN, TiN and Ti-B-N coatings were deposited onto H13 hot-working tool steel and alumina substrates by arc-PVD. The coatings were characterized with respect to their mechanical and structural properties. Oxidation behavior of the coatings on alumina substrates was investigated by TG/DTA. Samples coated on H13 substrates were oxidized in a tube furnace under atmospheric conditions at specific temperatures determined from TG/DTA tests of the same coatings deposited on alumina substrates. The oxide scale morphology was characterized by scanning electron microscopy and X-ray diffraction. Oxide scale thickness change and TG data were used to calculate oxidation reaction activation energies. It was determined that boron addition into TiN coating improves not only mechanical properties but also oxidation resistance. Depending on the substrate material different oxidation activation energy values for the TiN and Ti-B-N coatings were determined revealing the importance of film morphology on oxidation resistance.

Jan 1, 2006