Search Documents

By Kenneth M. Berrry

A unique situation has developed at an abandoned coal mine in St. Clair County, Illinois. Subsidence features have been observed at the ground surface over the mine including settlement of a pair of bridges for Illinois Route 158. The Illinois Department of Transportation (IDOT) is currently replacing the two bridges. Foundation treatment for the two new bridges included backfilling the mine void. The light rail system for St Louis (MetroLink) is also constructing a bridge over the same abandoned coal mine less than 1000 ft from the Route 158 bridges. The new MetroLink bridge is being constructed using piles which extend through the coal mine and overlying bedrock in order to transfer the loads to below the mine floor. The differing foundation types for the IDOT and MetroLink bridges were due to geometry and economic factors involved with the individual structures.

Jan 1, 2001

By L. B. Pankratz

The Bureau of Mines determined low-and high-temperature thermodynamic properties for anhydrous ferric sulfate and anhydrous indium sulfate. Low-temperature heat capacities were measured between 50° and 298° K, and enthalpy increments above 298° K were determined. The high-temperature measurements of Fe2(S04)3 extended to 900° K and those of In2(S04)3 to about 1,000° K. A minor transition was found for Fe2(S04)3 at 800° K, with a heat of transition of 540 cal/mole. Tabulations were made of the low-temperature heat capacities and the high-temperature enthalpy and entropy increments. The 298° K entropies derived from the low-temperature measurements were 67.6±0.S ca1/deg mole for ferric sulfate and 72.2±O.5 cal/deg mole for indium sulfate. High-temperature enthalpy increments were also given in equation form.

Jan 1, 1969

By C. Birch

"A ‘geologically constrained’ orebody model has long been hailed as vital for a Mineral Resource statement that is compliant with the South African Code for Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code). In this paper, the requirements for geological modelling as contained in the outline for the SAMREC Code are considered, and whether the new modelling software available on the market is a ‘black box’ or is better for modelling than traditional methods of wireframe creation.Implicit geological modelling is a technique that uses a radial basis function to establish and update geological models relatively quickly and efficiently from borehole data, outcrop data, manually interpreted vertical or horizontal sections, and structural data. Assays and any coded drill-hole data, such as lithology and alteration, can be interpolated.Leapfrog Geo software is an example of this new approach to geological modelling. A case study of a short training course in geological modelling for non-geologists at the University of Witwatersrand, as part of the Higher Certificate in Mineral Resource Management, is presented. The benefits of this type of geological modelling software are considered for this type of assignment as well as for mining industry applications.The use of geological models in mine planning is reviewed and a case study is presented comparing the variations in mine plan design and financial output of 13 final-year Mine Design projects from the University of the Witwatersrand School of Mining Engineering. These designs were all based on the same geological model created in the traditional way, and yet the resultant mine designs were significantly different, with very different resulting financial outlooks for the project. This raises questions as to how significant a very detailed model in the pre-feasibility and feasibility phases of projects really is, considering the huge costs involved in gathering the required data to build a SAMREC-compliant geological model."

Jan 1, 2014

By Vaughan R. Voller

"Over the last ten years an increasing number of heat and mass transfer models of solidification processes have been presented in the literature. A key component in these models is the coupling between thermal and solute fields. This is achieved by developing relationships based on the behavior at the microscopic scale in the casting (typically a secondary dendrite arm space). An important class of models in this respect are models that describe the local scale redistribution of solute alloy components-collectively referred to as microsegregation models. This paper explores this class of models.IntroductionModeling takes a key role in processing materials for properties. This is particularly time in solidification processes where current computer techniques allow for a detailed treatment of the critical macroscopic phenomena. Typically these macro scale models consist ·of three main coupled components.1. A model of flow in the melt and solid + liquid mushy region.2. A model of heat transfer.3. A model of solute transport.The focus of this paper is the solute transport component, in particular the manner in which process scale transport is coupled to transport ·at the local scale of the solid-liquid interface. This step requires a modeling of the redistribution of solutes at the scale of the secondary arm spaces in the dendritic mushy region-a process referred to as microsegregation. Basic microsegregation models use the limit assumptions of no mass diffusion in the solid (Gulliver-Scheil [l]) or complete diffusion in the solid (equilibrium lever rule) in a fixed and space. Recently, however, more sophisticated microsegregation models that account for finite mass diffusion and coarsening of the arm space have been developed [2-19]. In this paper governing equations for a general microsegregation model for a multi-component alloy in a coarsening and spacing _are introduced. From these general equations various models for a binary system are developed and tested"

Jan 1, 2000

By C. Richard Tinsley

INTRODUCTION Documentary complications arise from the risk apportionment in project financing which generally means that once the project is up and running and has satisfied the lender's completion test, the loan agreement specifically limits the lender's recourse to the project and its assets. It is the purpose of this paper to describe the special considerations which apply to industrial minerals projects and explore the reasons why so few project financings are negotiated in this industry. SIZE Small projects do not warrant the relatively high costs of negotiating and documenting project financing. The extent of the documentation is directly proportionate to either (a) the degree of risk apportionment, or (b) the amount of control given to lawyers to negotiate the documents. Although one would like to believe that project-finance documentation could be off-the-shelf, it is almost always necessary to tailor the documents to the mine development itself and the individual desires of the borrower. Accordingly, the documentation costs and initial expenses are seldom less than $40,000, and for complex projects can reach $400,000. In addition, banks often charge an up-front fee to partly compensate them for their staff time and partly to increase their yield on what is deemed to be a "riskier" loan asset. Another factor is the generally lower debt:equity ratio when bankers are uncertain of the accuracy of the cash flow projections. The ratio of the amount of cash flow left over after debt service to debt service itself is a key tool for project finance (debt service coverage). Bankers will require a higher coverage ratio for industrial minerals projects because of the relatively higher uncertainties in the following categories: Prices Markets Geology/Quality Transportation Environmental This, in turn, means that lower debt:equity ratios are the norm for new industrial minerals projects. INDUSTRY STRUCTURE It is hardly worthwhile to generalise about a field as diverse as industrial minerals, but there are four other structural reasons why project financing has not been widely applied. 1. The most obvious example is the predominance of small-sized operations, largely a function of transportation economics. Geological conditions also contribute to their dispersion. 2. Often, the product is only a small part of a company's business in contrast to many petroleum, metals, or coal companies whose sole business is the production of the raw material. The construction industry is a good example here for cement, gypsum, crushed stone, sand and gravel, and the drilling-mud services business for barite and bentonite. A company is unlikely to jeopardise its main business through the failure of a project financing on one of its key inputs. The corrollary is that the mined input is often regarded as a cost centre and not run on the sort of economic basis suitable for project financing. 3. There may be a reluctance to reveal key aspects of an industrial minerals venture to an outsider for purely competitive reasons. Unlike the other minerals industries which readily share technical information at plant visits and

Jan 1, 1985

By L. K. Sinclair

In situ leaching of copper has the potential to deliver low-cost recovery for soluble copper deposits of sufficient permeability. In order to provide key inputs for modeling of the in situ leaching process, bench scale test work can be used in conjunction with geochemical software to identify key leaching and precipitation reactions. A case study is presented in which a series of flow-through acid leaching tests were conducted on drill core sections from a porphyry copper deposit without crushing or grinding. Concentrations of copper and other key elements were monitored in the recirculating leach solution over several months. A geochemical model of each leaching test was prepared using Geochemist's Workbench using a combination of diffusion-controlled and reaction-controlled rate mechanisms. Key reactions included leaching of chrysocolla, iron oxides, and plagioclase. The model was able to simultaneously satisfy the evolving chemistry of the recirculating leach solution, mineralogy of the head and leach residue, measured acid consumption, and leaching rates for key minerals reported from previous laboratory studies. Opportunities and limitations for scaling up the model to simulate the commercial wellfield are discussed.

Jan 1, 2015

By S. Johnson

Introduction The mining of aggregates underground has grown steadily over the last 25 years. Growth has come in both production volume and in the importance this segment of the industry is playing in the continuing supply of construction aggregate. Underground aggregate mines will continue to grow in both number of operations and complexity, as the replacement of zoned reserves in metropolitan areas becomes crucial. This growth will result in a shortage of qualified mine managers, possibly limiting the success of these facilities. The aggregate industry will have to modify current practices in order to meet the growing demand for this specialized skill. Segment Growth Underground mining for aggregates is not a new idea. Martin Marietta has been operating underground mines since 1969, and currently operates 16 underground mines ranging in size from 250,000 tpy to 2,500,000 tpy. These mines represent less than 4% of the total number of operating locations, but contributed 9% of the annual production in 2004. Though they range in size and production capacity, the importance is evident. The 2000 United States Census revealed several trends that are of interest to the aggregate mining industry. For the period 1990-2000 the U.S. population grew by 33 million or 13%. There were nine major metropolitan areas with a population of five million or more. These nine areas accounted for 30% of the total U.S. population. More significant was the fact that the population growth in these nine metro areas was 25% of the growth for the entire country. These statistics tell us that the population is expanding in these major metropolitan areas at a staggering rate. The same thing is happening to some degree in every population center. Population growth increases the demand for local aggregate while reducing the available area to mine that aggregate. The need for an economical supply of aggregate to support community expansion is a problem that will grow as older quarries are mined out and closed. This will be an issue that communities of all sizes will have to deal with. A reliable and cost effective supply of quality aggregate is crucial to support community expansion.

Jan 1, 2006

By L. G. E. Bignell

Surveying what was done in 1929 in meeting problems of oil-field equipment corrosion, one is struck by the fact that fewer meetings were held for discussion of these problems and fewer papers written than in any year since the subject engaged the attention of petroleum engineers. This does not mean that progress has not been made, for a great deal actually has been accomplished. Recommendations that accompanied field reports have been put into actual trial and some results obtained are gratifying. The type of papers prepared also has undergone a change, for they now deal with things accomplished rather than recite damages and suggest possible remedies. Some of the most notable work pointing the way for future solution of many pipe line problems is that done for the U. S. Bureau of Standards by Dr. K. H. Logan and Dr. Gordon N. Scott, dealing with tests of pipe coatings and reports on soil conditions. Many facts of great importance have been isolated and defined by these two men, not only indicating what may be done in some instances to retard corrosion, but showing that things formerly considered of importance have little bearing apparently upon the practical results. All-aluminum Storage Tanks In April, 1928, an all-aluminum 500-bbl. field storage tank was put into actual field use in Crane County, Texas, together with another tank of the same capacity but made with steel bottom and lower section of side sheets and aluminum upper ring of side sheets and deck. In April, 1929, after a little over one year's use these tanks were opened and examined by a group of engineers and chemists. The results of the test were enlightening. Other tanks made entirely of steel and used in the same battery with the two test tanks had some of their side and bottom sheets destroyed by corrosion in six to nine months, but the all-aluminum tank was in actual use for 18 months before holes were found corroded through the bottom, when the tank was examined for a second time in September, 1929. This field test of the aluminum tank confirmed the already known

Jan 1, 1930

By Bryan Denby

The curvilinear nature of shear strength envelopes for rock discontinuities may be simply and precisely represented by a power curve. The development of shear strength criteria applicable to rock discontinuities is reviewed and related to a theoretical basis for curvilinearity. An approach is reported to enable the quantification of the two power curve indices using a nomogram based on empirical studies. Using a knowledge of discontinuity basic friction angle and peak dilation angle the relevant indices ranges may be predicted for mine slope studies.

Jan 1, 1984

By D. Milne

Laser profilometers exist for obtaining very accurate two and three dimensional profiles of joint surfaces. The application of this technology is not commonly applied to the collection of field data on discontinuity surface roughness. Rugged and portable field devices are not commonly used and the value of the possible field data that can be collected has not been well recognised. This paper reviews commonly used field techniques for assessing discontinuity roughness, discusses the value of this data and presents a new laser profilometer design for field application.

May 1, 2009

By C. D. Woodward

The Anaconda Copper Mining Co. purchases 25,000 kw. of electric power for its mining operations at Butte, Mont. This power is delivered, over duplicate feeders, in the form of 60-cycle, 2400-volt, three-phase current, to five compressor plants, where most of the energy is used for driving air compressors. At the compressor plants are located the switching apparatus for controlling the 2400-volt power and distributing it to the various mines. At these points, also, there are a number of motor-generator sets for converting the alternating current to 275-volt direct current for the haulage systems. Pole lines convey the powcr from the compressor plants to outdoor transformer substations at most of the mines. When it is not economical to distribute the power at the lower voltages in the mines, transformers and motor-generator sets are placed at strategic points underground. All power is purchased on a maximum-demand basis; therefore there is installed at one of the compressor plants an eight-element totalizing graphic wattmeter. This instrument records simultaneously the value of all power taken at the numerous points of delivery, which not only climinates the diversity factor but permits load dispatching between compressor and pumping plants, and thus materially reduces the maximum demand from the power system. As most of the mine hoisting is done by 90-lb. compressed-air winding engines, the air-compressor equipment for the winding engines and mining operations is quite extensive. The standard air compressor has a rating of 7500 cu. ft. per min. of free air, and most of the compressors are directly connected to synchronous motors. The synchronous motors are designed for 80 per cent. loading power factor, thus facilitating power-factor correction of total mine load. Consequently by cooperation with the power company, the voltage of the power received at the compressor plants is constant. In the mines there are installed an induction motor load of approxi-mately 10,000 hp., and 4500 kv.-a,, in transformer capacity. It is the practice to install 2200-volt motors in the mincs, except those rated below 50 hp, hence there are in operation underground about 5000 hp., in the

Jan 1, 1923

By C. D. Woodward

The Anaconda Copper Mining Co. purchases 25,000 kw. of electric power for its mining operations at Butte, Mont. This power is delivered, over duplicate feeders, in the form of 60-cycle, 2400-volt, three-phase current, to five compressor plants, where most of the energy is used for driving air compressors. At the compressor plants are located the switching apparatus for controlling the 2400-volt power and distributing it to the various mines. At these points, also, there are a number of motor-generator sets for converting the alternating current to 275-volt direct current for the haulage systems. Pole lines convey the powcr from the compressor plants to outdoor transformer substations at most of the mines. When it is not economical to distribute the power at the lower voltages in the mines, transformers and motor-generator sets are placed at strategic points underground. All power is purchased on a maximum-demand basis; therefore there is installed at one of the compressor plants an eight-element totalizing graphic wattmeter. This instrument records simultaneously the value of all power taken at the numerous points of delivery, which not only climinates the diversity factor but permits load dispatching between compressor and pumping plants, and thus materially reduces the maximum demand from the power system. As most of the mine hoisting is done by 90-lb. compressed-air winding engines, the air-compressor equipment for the winding engines and mining operations is quite extensive. The standard air compressor has a rating of 7500 cu. ft. per min. of free air, and most of the compressors are directly connected to synchronous motors. The synchronous motors are designed for 80 per cent. loading power factor, thus facilitating power-factor correction of total mine load. Consequently by cooperation with the power company, the voltage of the power received at the compressor plants is constant. In the mines there are installed an induction motor load of approxi-mately 10,000 hp., and 4500 kv.-a,, in transformer capacity. It is the practice to install 2200-volt motors in the mincs, except those rated below 50 hp, hence there are in operation underground about 5000 hp., in the

Jan 1, 1923

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS. GENTLEMEN: Submitted herewith are the report of the Treasurer for the year 1941 and re¬ports for the same year of the following standing committees: Admissions, Mem¬bership, Papers and Publications, Mining and Metallurgy (Magazine), Library, and Student Relations. These reports present additional details. Membership For the fourth year in succession, mem¬bership reached a new all-time high, level as shown in Table 1. The total at the

Jan 1, 1942

By C. M. Egert, S. Rajic

"We have developed a monolithic micro-spectrometer suitable for a variety of sensing applications including industrial process monitoring. The device consists of a solid structure with a volume less than 6 cubic centimeters. All optical components of the spectrometer including two aspheric mirrors, a diffraction grating, and entrance and exit surfaces are fabricated onto the surface of the structure. All light paths are internally contained within the structure. The result is a small, rugged spectroscopic sensor ideally suited for use as a process monitor. Due to its monolithic nature the device requires no post-fabrication alignment; nor can it be knocked out of alignment during use. Although many materials and thus wavelength regions were possible, the prototype device discussed here was produced in PMMA by precision diamond turning. However, lower cost manufacturing approaches involving injection molding are under development to produce an affordable sensor.Due to its rugged monolithic design, small footprint, and low cost the monolithic micro-spectrometer is ideally suited for distributed monitoring applications often required for industrial processes. It is expected that modified versions of this sensor designs will be required for specific applications so as to maximize the performance and resolution over the operating range. For example, the prototype device described here operates over a wavelength range of 500 nm to 1000 nm. The performance of this device as a real-time surface monitoring sensor will be discussed in detail. Our approach of using wavelength dependant scattering resulted in the reduction to practice of a miniature, monolithic, rugged, low-cost, micro-instrument in a sensor sized package. The process sensor applications community has been faced by the cost versus performance issue. Simple go/no-go sensors are typically inexpensive but they provide very limited and sometimes dubious data. Scaled down traditional instruments offer very good measurand information but are typically cost prohibitive, fragile, and still relatively large. This work will bridge the gap between these two extreme sensing alternatives."

Jan 1, 1997

By A. Pagliero

The coulombimetric reduction method has been used as an evaluation technique for Pb-Ca-Sn anode corrosion in the LIX-SX-EW process. The proposed methodology involves three consecutive steps, i.e., cleaning, oxidation and reduction. They are carried out in the same experimental unit, in solutions containing 180 g/L H2S04 with and without the addition of cobalt. The authors have worked in a wide range of oxidation current densities, from 150 to 500 A/m2 for in a period from 0.5 to 120 hours. It can be concluded from the results that there would be a linear relationship between the applied electrical charge I*T (Coulomb) and the anode corrosion expressed as transformed Pb mass (mg), for solutions with or without the addition of cobalt. The exception is that for the last one the corrosion rate is 5 times faster, which was observed for every layer. From the evaluation of different corrosion layers, one can point out that its composition is mainly in the form of sulphate. In the presence of cobalt, about 67% of Pb would be as sulphate (PbSO4), about 27% as a basic oxide (PbO) and only 6% as oxide PbO2 on the surface. From this result, it appears that great transformations occurred in the metal/sulphate interface. Without the addition of cobalt, the proportion of oxide Pb02 on the surface increased up to 11.5%. According to the previous statement and considering that Pb was found mainly as sulphate, the authors recommend its determination be used as quality selection criterion. Its evaluation should be performed in the acid solutions with 200 ppm cobalt addition at an oxidation current density of 300 A/m2 for a period of 24 hours.

Jan 1, 1999

By J. Hoover

Real growth in the economy, increasing demand for electricity, and consumer stockpiling for a possible United Mineworkers of America (UMW) strike in October made 1984 a banner year for coal. Production and consumption climbed to record heights. Precautionary purchases brought inventories close to the peak levels of early 1981 when coal miners walked out for 72 days. Production slowed in the fourth quarter after labor and management concluded negotiations without a walkout. But output in every major coal producing state showed significant gains during the year US coal production totaled 807 Mt (890 million st) in 1984. This is a 13.8% increase over 1983 output. Lower production rates, principally in Appalachia, and sustained demand in the final quarter put downward pressure on coal stocks by the end of the year. Demand All market sectors experienced greater requirements for coal in 1984. Electric utility coal consumption increased 6.3%; exports climbed 4.8%; coke plants consumed 18.9% more coal; coal requirements in the other industrial sector expanded by 11.8%; and consumption in the residential/commercial sector rose 8.1%. Domestic consumption of coal reached a record 718 Mt (791 million st) in 1984. This is a 7.4% gain over the previous consumption high of 668 Mt (737 million st) in 1983. Electric Utilities The 4.6% increase in electric power generation in 1984 was coupled with expanding coal use relative to other energy sources. This resulted in a 6.3% rise in coal consumption, totaling 603 Mt (664 million st) for the year. Thirty-eight of 45 states where coal-fired electric power plants were operating shared in the 36-Mt (39 million-st) increase in electric utility coal consumption

Jan 5, 1985

By H. Maleki, G. Tetreault

This study was initiated by the US Bureau of Land Management (BLM) to develop guidelines for determining the maximum economic recovery of resources in coal mines. The work was in response to a requirement in the Mineral Leasing Act of 1920 and Federal regulations. The intent was to address the economic rainability of small, irregular reserves in existing longwall mines. In particular, there was a need to determine if room- and-pillar mining using a continuous miner (CM) was economically sound or whether unconventional (short or odd-shaped) longwalls could be used to recover small coal reserves economically. Small reserves, called "widgets " are left in longwall mines on one side of the mains near outcrops and adverse geological conditions or near any other location where reserve geometry does not lend itself to mining with a rectangular longwall panel. The work included the analysis of the geologic, geotechnical and economic factors that influence the recovery of small coal reserves; the analysis of historic changes in supply, demand and coal prices; the development of typical cost models for room-and-pillar and longwall mines; and the development of a practical methodology for determining maximum economic recovery. The methodology included an evaluation of the ratio of coal mined during longwall mining to that mined for development (LDR), as well as costs of maintaining coal quality depending on market conditions. The LDR is a good indicator of mine efficiency and overall coal recovery in modern longwall mines and, thus, is used to evaluate the increased costs associated with adding new development sections for extraction of small reserves. The study examines the economic feasibility of using unconventional longwalls for the recovery of medium-sized reserves, depending on site-specific geologic and geometric conditions.

Jan 1, 2002

By Dyne GD

From experience in the design and operation of power station combustion facilities in most mainland Australian States, involving a wide range of black coals and lignites, and in the specification and procurement of coal supplies for power station use, techniques for the optimisation of coal resource development and power generation utilisation have been developed to ensure compatibility between characteristics of the selected coals and power station design. These techniques include computer data bases for resource data handling and computer simulation of coal-fired boilers for determining coal property cost effects. Data Base Systems allow results of coal analyses to be efficiently handled, to assist in the review of the relevance of resource data to the coal sections proposed to be mined and the coal fractions proposed to be marketed. Data Base Systems also facilitate the marshalling of coal quality data into basic utilisation format to enable a proper utilisation review and analysis of the certainty and scatter of coal properties. Computer simulation of the effects of different coal properties on the capital and operating cost of power stations is achieved by establishing conceptual design parameters of the major items of plant to relate the variations in coal specification to equipment size and type. Variations in power station budget costs can then be determined using the computer model for variations in coal specification.

Jan 1, 1983

By H. Kinilakodi

In 2008, the authors developed a methodology for assessing underground coal mines for high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later using a sample of 103 mines with 2008 and 2009 data, injury measures and MSHA citation data were combined into a Safe Performance Index (SPI). The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. In this paper, comparisons are made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performances as compared to large and medium-sized mines.

Jan 1, 2011

By Ulf Nyberg, Changping Yi, Daniel Johansson, Håkan Schunnesson

To investigate the non-ideal detonation properties of aluminized emulsion explosive, a series of tests for an emulsion explosive with 5% aluminum powder additive were carried out with mortar confinement. The velocity of detonation (VoD) and the curvature of the detonation front for different charge diameters were obtained from the tests with a high-speed camera

Feb 1, 2020