Search Documents

By David A. Paul

Over the past several years a great deal of information on blasting vibrations and their effects on structures has been generated. Much of this knowledge has been gained through the use of ground vibration measuring equipment. While this type of information is valuable and gives us great insight into damage that can be incurred by structures from this source, very little, if any, information of this quality is available for the vast majority of cases in which an engineer is called upon to investigate alleged damage from ground vibrations. For the investigative engineer, then, the problem becomes one of accumulating whatever data is available and drawing a conclusion as to whether or not the subject structure was in fact damaged by the blasting vibrations. Such an analysis certainly requires a working knowledge of the literature on the subject and as much experience as he can bring to bear. Even thus armed, however, the data is often ambiguous, confusing, and/or contradictory. A practical approach is presented herein to aid the engineering investigator in arriving at the best possible conclusion available with the information at hand.

Jan 1, 1983

By S. Asano

Hydrometallurgical processes for treating copper sulfide concentrates have attracted considerable attention over thirty years and many processes have been developed. However there have been still problems in those processes because of difficulties of iron removal and high purity copper production with low operating cost. Although SX-EW is highly cost effective method, it is difficult to process the chalcopyrite. Sumitomo Metal Mining Co., Ltd. (SMM) conducted a review of hydrometallurgical copper concentrate processing and has successfully developed a novel process for the hydrometallurgical production of copper from copper concentrate. In this process, copper sulfide is leached by chlorine gas under atmospheric pressure. Most of hydro metallurgical processes can leach only some of chalcopyrite under atmospheric pressure then they need high pressure leaching facility like autoclave. In this process, copper in chalcopyrite can be leached completely by controlling oxidation reduction potential and chloride ion concentration. Cu(I) ion in leached liquor is separated from Fe(I!) ion by SX using TBP then pure copper powder is produced by electrowinning. Results in batch and continuous testworks and pilot plant tests at Niihama Research Laboratories are presented in this paper. Cu2007

Jan 1, 2007

By Frank Ladwig, Stephen Gos

Tailings and/or wastewater generated from gold extraction plants employing cyanida­ tion must often be treated to remove the cyanides and heavy metals for environmental reasons and/or gold extraction inhibition reasons, due to the presence of heavy metals like copper, which have a detrimen­ tal effect during cyanidation. In recent years, the treatment of effluents contain­ ing cyanides and heavy metals has been widely studied, Among chemical treatment methods, the use of hydrogen peroxide has been universally employed as a viable option. However, in some cases, effluents containing high concentrations of heavy metals and/or solids decompose the hydrogen peroxide, an undesirable side reaction. The addition of stabilizers or other peroxygen compounds together with hydrogen peroxide can, however, considerably reduce the rate of decomposition and thus result in detoxi­ fication costs, which are considerably less than the standard detoxification process using hydrogen peroxide. In some cases, the reaction rate can also be increased, resul­ ting in lower investment costs for new detoxification plants. This paper deals with the results of developmental work performed in the recent past and introduces some new processes with the aim of optimizing reagent consumption and costs.

Jan 1, 1992

By G. I. Voiloshnikov, A. F. Panchenko, N. S. Voiloshnikova

Low world gold prices stimulate development and introduction of economically efficient ( cost saving) technology for operating gold mills. This report covers the results of testing and introduction of CIL technology to recover gold from flotation concentrate of Samarta gold concentration plant located in Buryatia (Russia). This plant is treated the ore of Zun Kholba gold deposit using gravity and flotation of gravity tails as preconcentration processes. Till recently high grade gold gravity concentrate was smelted to gold bullion and shipped to gold refinery, gravity middlings were leached by cyanidation in cone type equipment developed by Irgiredmet and flotation concentrate shipped to copper smelter. The disadvantages of flotation concentrate shipping to copper smelter are following: high concentrate transport cost; problem with gold shipped balance; high cost of flotation concentrate treatment; comparatively low gold recovery. In this connection IRGIREDMET developed the hydrometalurgical technology for gold recovery from flotation concentrate. The flowsheet was developed on the base of laboratory, pilot plant and industrial scale tests conducted by IRGIREDMET in 1987-1997 and lrgiredmet experience on CIP process testing and industrial scale introduction in Yakutia [1-6]. The flowsheet is presented in Fig.1 and consists of following base operations: concentrate regrinding;

Jan 1, 1999

By J. K. Ahlness

The US Bureau of Mines investigated technologies for determining the integrity of in situ leach mining wells. A self-contained trailer-mounted well integrity testing system (WITS) was designed and built to enable rapid testing of well casings for leaks as required by environmental regulations. The WITS utilizes two inflatable packers to seal off the entire casing length or any portion thereof. Water pressure is built between the packers to the desired test pressure, and the presence or absence of casing leaks is determined by monitoring the pressure drop between the packers. A winch and steel cable are used to run the packers in and out of the well. The WITS underwent an industry field test at the Irigaray in situ uranium leaching mine near Buffalo, WY. A total of 37 wells with an average depth of 69 m (225 ft) were tested at an average rate of four wells per eight-hour shift with a two-person operating crew. This represents a 75% time savings and an 83% labor savings compared to the rigid-pipe method previously used at the mine, with which a three-person crew tested an average of one well per shift.

Jan 1, 1988

By F. A. Emmerton

I have used for about two years, in the laboratory of the Joliet Steel Company, a rapid method for the determination of phosphorus in iron, steel, and ores, which possesses one or two features sufficiently novel to warrant description. In general, it is the method described by Mr. Benjamin B. Wright (Transactions, vol. x., p. 197), involving the precipitation of the phosphorus by means of molybdate solution, and its estimation in the yellow precipitate by reduction of the molybdic acid, and titration of the resulting oxide with a standardized permanganate solution, according to the principles laid down by Werncke (Fres, Zeit., vol. xiv., p. 1). In the use of this method, I had difficulty at first in obtaining a yellow precipitate of reasonably uniform composition. It is a well-known fact that, to secure this result, the conditions of precipitation must not vary. The principal condition is temperature; and acidity, concentration, proportion of nitrates and chlorides, and time, are important elements. I am aware that uniformity in these conditions has been obtained to a reasonable extent by many chemists,. so that they are enabled to use with success, methods based on the

Jan 1, 1887

By Matthew E. Eisenmann, Gerald H. Luttrell

Performance data from phosphate plants are often untrustworthy because of difficulties associated with highly variable feeds and unstable equipment operation. In some cases, this problem is further compounded by improper sampling procedures and unreliable laboratory analyses. Questionable data often lead to misleading conclusions that result in lost productivity and profits. Data reliability may be checked using mass balances, but the mathematics associated with this procedure can be overwhelming when multiple data sets or complex circuits are evaluated. To overcome this problem, a simple spreadsheet-based mass balance program has been developed specifically for plant operators. To use this program, operators simply enter a description of their circuit and input the assay values (e.g., % BPL, % Insol, etc.) for each stream. The program then generates the best estimates of the assay values and flags values that may be unreliable. The spreadsheet is specifically designed to be easy to use and requires no knowledge of statistics or programming. This manuscript reviews the mass balance problem and describes how spreadsheet programs can be used to evaluate plant data. An example problem involving the analysis of data around a two-stage phosphate flotation circuit is presented.

Jan 1, 2002

By Paine GG

The in-situ retorting of shallow oil shale deposits is an attractive alternative to the material handling problems of conventional open pit mining techniques, which involve removing overburden, fragmenting and transporting the shale to a fixed retort, and finally disposing of the hot spent shale.For in-situ retorting to be successful, the oil shale has to be fractured and the fragmented rock expanded into a void, to allow controlled propagation of a flame front through the in-situ retort. The principles of cratering with explosives have been used to develop a process for the in-situ fracturing of a thin oil shale deposit overlain by a formation of porous rock. The overlying porous rock formation is first compressed by explosive charges to create voids in the porous rock. The oil shale is then fragmented and pushed in to the voids with separate explosive charges. This paper discusses methods of creating voids in porous rocks with minimal surface disturbance, and then methods of obtaining the most uniform fragmentation of the shale. The whole process can be completed, in practice, in one blast. The results of an experimental blast are presented, and possible modifications are then discussed.

Jan 1, 1985

By R. Hogg, D. W. Fuerstenau

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation, and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most clearly met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80% of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50% of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1973

By Yanping Xiao

In submerged-arc furnace (SAF) for smelting chromite ores into ferrochrome, there exist large temperature gradients and wide distributions of mineralogy and compositions in the furnace, due to the complexity of feed structure and electrical-thermal-chemical interactions. This leads to various zones in the furnace and thus different reaction mechanisms. In the present paper, the behaviour of chromium in the submerged arc furnace is discussed in various reaction zones, including solid state chromite reduction in the packed bed zone, chromite dissolution and reactions in the smelting and coke bed zone, and recovering chromium from slag to metal. In the gas-solid reaction zone, the reaction mechanism is discussed based on the experimental observations and analysis. In the smelting zone, the behaviour of partially reduced chromite and slag formation are analyzed based on the information in literature. The slag in FeCr process contains mainly Al2O3, MgO, SiO2, CaO and CrOx, featured by chromium with both divalent and trivalent oxidation state, which plays an important role for chromium recovery into metal. The factors influencing the slag and metal interfacial reactions and the chromium recovery are addressed.

Jan 1, 2006

By F. Mauviel, J. Bernard, G. Herrouin, J. P. Lenoble, C. Charles, B. Taine

Manganese nodule projects were quite fashionable during the 1970s. At the beginning of the 1980s, low metal prices led to an almost complete reduction of such activities; however, the Law of the Sea incited the countries that signed it to build a strategy for this ocean resource. Gemonod was created in France in 1984 with a four-year mission. This paper presents the results of its program devoted to the technical and economic studies of nodule exploitation. A commercial mining system is presented. The nodules would be collected by a self-propelled miner and lifted hydraulically through a rigid pipestring. A complete optimized scenario has been built taking into account offshore mining, ore transfer at sea, transportation and processing to analyze the profitability of the project. Considering an average conservative basis for metal prices, after a deep analysis of the market, the return rate of investment of the project appears fairly interesting. These results are new and are explained in comparison with previous foreign studies. These results must not hide the innovative nature of the project nor the associated risks. This is why a mining pilot is required and has been specified by Gemonod.

Jan 1, 1991

Conflicting claims and views on the priming of ammonium nitrate/fuel oil (ANFO) are reviewed; certain fallacies and misconceptions are rectified. Optimum priming systems for a range of blasthole conditions are indicated. Moves towards optimum priming lead to reductions in the combined cost of drilling, blasting and handling the material. With shallow blastholes, two-point priming is rarely warranted. Best blasting results from single priming are usually obtained when the primer is located near, but not at, the bottom of the blasthole. As blast- hole depth increases, two-point priming becomes more reliable and effective than single priming. For two-point priming, primers should be located such that detonation waves in the ANFO collide at grade level or, if preferred, within a hard band in the burden. Where blastholes are very deep and/or strata variations can be appreciable, three or more spaced primers are often justified. The effectiveness of a primer varies with its detonation pressure, diameter and length. Primer properties influence the velocity of detonation (VOD) near the primer, but do not affect the final (steady-state) VOD in the ANFO. Some primers cause 'run-up' (i.e. lower than steady-state) velocities whereas others cause

Jan 1, 1974

By Jack L. Woodward

The evolution of surface mining equipment has resulted in larger, faster haulage units, loaders, etc., resulting in increased demands on steering technology. Careful analysis of these systems was warranted to determine if steering-related safety problems have been introduced. The objectives of this program were to: 1. Define the generic types of steering systems being used on mobile mining equipment used in surface mining operations. 2. Gather information on steering-related accidents in mining operations. 3. Assess the need for initiating government-sponsored research into steering system technology. A comprehensive literature survey was conducted concurrent with extensive contacts with mining operations, mining equipment manufacturers, steering system component manufacturers, and government agencies. A Technical Evaluation Group composed of representatives from the above organizations was formed to review the data gathered. It was concluded that the steering systems in use on surface mining equipment are reliable and do not present a safety problem. The Society of Automotive Engineers, Inc. is active in pre-paring voluntary consensus standards to assure that the minimum levels of performance are defined for industry.

Jan 1, 1979

By M. N. Brodie, John Chapman

INTRODUCTION - DEFINITION & HISTORICAL PERSPECTIVE While this symposium is concerned with comminution which, by definition, relates to all stages of size reduction of an ore body to a form suitable for mineral separation, the electrical drive aspect of the grinding section will receive most attention in contrast to the crushing, screening and materials handling elements of the process. The reason for this is that today's large mills, thirty feet diameter and upwards, present mechanical and electrical problems which require a degree of sophistication in their solution not previously required. The ability to satisfy these demands, so far as electrical technology is concerned, largely results from the development of semi-conductor devices. These can now handle typical electrical distribution power levels within remarkably s m all volumes and with high efficiency when compared with the motor-generator sets, mercury arc rectifiers, rotating amplifiers, magnetic amplifiers and vacuum tubes which were commonly used to provide speed and torque controls as recently as the early nineteen-sixties. The hardware available to the electrical engineer has changed dramatically whereby even the simplest control system formerly using hard-wired relays is now superseded by the program m able logic controller with its computer-like memory containing the sequence of operation, in other words, the software. Reverting now to the mineral process itself, it is assumed that the ore body has been mined using explosives and is delivered to the concentrating plant in its 'run of mine' form. The problem becomes one of reducing the material to a size which will permit an acceptable recovery of the mineral with the most economical use of energy. The size of 'run of mine' material will range from about minus five feet for high tonnage open pit operations to minus two feet for the smaller underground mine. The final reduction in size may range from minus ten mesh to minus two hundred mesh (exceptionally as fine as minus six hundred mesh) depending upon the concentration method and dissemination of the mineral values within the ore. There is no single circuit that satisfies all applications, but the pattern of metallurgical equipment use shown in Table 1 appears discernable from current practice, in general terms.

Jan 1, 1982

Study on Mineral Processing Technology for a Refractory Iron Ore

Sep 13, 2010

Much of the coal and gold mining industry of New Zealand is small scale. Funding is tight and mechanisation limited. The country has many well documented small coalfields (some with significant outcropping) and alluvial gold deposits. These are generally remote, difficult to access (physically and otherwise) and of submarginal value (largely a consequence of size when viewed for extraction by traditional techniques). The industry is also burdened by environmental and bureaucratic constraints. The above over simplified setting suggests to the Author, a newcomer to New Zealand, the opportunity to consider some novel concepts based on technology and techniques developed overseas or borrowed from other industry sectors. The objective being to make viable in economic and environmental terms projects that might otherwise be stillborn if considered for exploitation by conventional means. The paper mainly discusses 2 concepts focusing on the application of augers for exposed high wall or outcrop coal and micro-tunnelling augers for alluvial gold extraction. These may be considered high mobility 'container' (as in shipping container) packaged, or 'non invasive' mining systems. It is stressed that these are but concepts and have yet to be subjected to rigorous financial or engineering scrutiny. This could only follow their acceptance by, and input from, New Zealand miners. There will also be brief mention of a new modular conveyor system which might have application within the concepts or existing small scale mineral extraction operations and mention of a project currently in progress to apply tangible 'sustainability' to underground coal mining.

Jan 1, 1996

The Pacific Rim and its environment involves a vast array of natural phenomena, and a vast array of situations which show the impact of man. Almost half the world's population of over five billion live in nations" which border the Pacific, but the concentration is focussed in the North. Great experiments are occurring in this region, the industrialization and energy development in- Japan and China, the growth of Indonesia, (now 168 million - soon 368 million; Brown and Jacobson, 1986), the enormous developments of agriculture and the metals resource base in Australia and China. At the same time, the Pacific Rim does not project images of hopelessness, the mood is upbeat. Over the past decade, incomes have increased substantially in most of the major countries of Pacific Rim (e.g. over the period 1980-86, + 58% in China, + 21% in Japan, + 34% in South Korea; Brown and Jacobson, 1986). In September, 1986, at the general assembly of the International Council of Scientific Unions (ICSU) in Bern, Switzerland, representatives of over 50 nations approved a new initiative, "The International Geosphere Biosphere Programme: A Study of Global Change". The focus of this new program is "To describe and understand the interactive physical , chemical , and biological processes that regulate the total Earth system, the unique environment that it provides for life, the changes that are occurring in this system, and the manner in which they are influenced by man. The IGBP will be a tightly-defined programme of research, directed at providing fundamental knowledge that will serve as a basis for assessing likely future changes on the Earth in the next 100 years" (ICSU, 1986). For the earth scientist, and all resource scientists, there is an emerging agenda; new priorities are appearing, new questions are being asked. The recent report of the World Resources Institute (1986) focusses on this emerging agenda. Topics which are at centre stage in this report include the following: The environment and human health Tropical deforestation The atmosphere as a shared resource and climates Soil-degradation Rural-urban migrations Food and agriculture The diversity of species-ecosystems Freshwater as a finite resource Coastal areas and resources

Jan 1, 1987

By J. B. C. Wu, B. McKee

"Mining along with subsequent processing of the minerals often presents conditions where a wear- and/or corrosion-resistant alloy is needed to minimize downtime and maximize efficiency. This paper is intended to give an overview of the alloys that are currently being used, as well as those developed in recent years that could be used in the mining industry. Emphasis will be put on the iron-, nickel-,cobalt-based alloys and composites containing a variety of carbides. The characteristics, properties, product forms, and methods of application are presented. In addition, examples of the actual use of these wear-resistant materials are illustrated.IntroductionPreventing wear and corrosion is important in any industrial operations. In the mining industry, the process equipment typically suffers many different types of material degradation. Abrasion, impact, erosion, metal-to-metal wear and corrosion are typically encountered. Each situation requires different material characteristics to retard the degradation process. Therefore, it is essential to understand the characteristics of the materials and the effects of the alloying elements.There are four common classes of metallic materials for resisting wear and corrosion; namely, iron-based alloys, nickel-based alloys, cobalt-based alloys, and carbide-containing composites. Each class of material has its own characteristics. Depending on the chemical composition, the materials within each class can be vastly different in properties. In recent years, there have been materials developed in each of the four classes using the knowledge of the metallurgical principles and the effects of the alloying elements on the material degradation process.To use a wear-resistant alloy, it is also necessary to understand the available product forms and their application methods. Weld overlaying is a traditional way of using these alloys (Wu and Redman, 1994). In recent years, thermal spray is becoming popular. For applications where over-laying and spraying are impractical, solid components can be made by a variety of casting and powder metallurgy techniques. They can also be fabricated from the wrought products.To select a proper material for an application, it is important to understand not only the characteristics of the wear-resistant materials but also the degradation process. Due to the complexity of the processing environments, past experience is also helpful in making the decision on the material selection."

Jan 1, 1997

By J. M. Ohm, C. M. Bunker

Two special tools for recovering gamma-ray probes and logging cable from drillholes have been designed by Ohm and Bunker and constructed by Ohm. Though intended specifically for U. S. Geological Survey equipment, they may be used with other equipment of the same general type. Fishing Tool for Probes: A fishing tool of the overshot type (Fig. 1) was designed to retrieve logging probes (sondes) that become disconnected from the logging cable and are trapped in the drillhole. When the tool slides over the top of the gamma-ray probe, studs on the bottom engage the shoulder near the top of the probe (Fig. 2), which is then pulled to surface. The barrel can be constructed from brass or steel tubing. Wall thickness is not a critical dimension, but the tool should be heavy enough to sink through mud or water in the drillhole. The internal length of the tool must be enough to prevent interference with the upper end of the probe head as the tool slides over it. The design of the probe head used by the USGS required a minimum free space of 2 1/2 in. inside the fishing tool, which was made 7 1/2 in. long to increase the weight. The lower end, which engages the shoulder of the upper end of the probe, contains three studs placed at 120" around the circumference of the tool and held in the engaging position by the tension of a spring wire. The studs can be made of any metal, such as steel, having high tensile strength. As the tool slides over the probe the studs are pushed outward from the center against the spring tension, allowing the tool to slide into position below the shoulder of the probe head. The spring tension forces the studs inward into the engaged position after they pass the shoulder. When the tool is raised the studs stop against the shoulder, preventing the tool from sliding up over the top of the probe. Once it engages the shoulder of the probe it cannot be freed until both probe and fishing equipment are recovered from the drillhole.

Jan 1, 1960

By J. E. Schaefer

A summary of oil and gas development in Ohio for 1936 is necessarily brief and, in some details incomplete, owing to the lack of a central state agency for the collection of data and statistics on well drilling and production. The information used in this report was compiled from the records of the several companies operating in the state. Drilling activity in Ohio increased during 1936 as compared to the two preceding years. During the year 1157 wells were completed, as compared to 1022 wells in 1935 and 1055 wells in 1934. However, in spite of this increase in drilling activity, both oil and gas production declined for the year. Activity by Fields Trenton Sand Field.—The Trenton sand field is located in 15 counties of northwestern Ohio, trending from Toledo on the north, south and west through Findlay into Indiana. About 40 years ago the Trenton field was one of the most important oil-producing fields in the United States, but it has declined to a position of minor importance. During the year 1936 there were 52 completions in this field—29 gas wells, 19 oil wells and 4 dry holes. Clinton Sand Field.—The Clinton sand is by far the most important gas-producing field in the state. Production is located in small pools separated by nonproducing areas, on a band of varying width reaching from Cleveland on the north to Lawrence County on the Ohio River on the south. During 1936 a small pool of patchy character was developed in Butler township, Knox County. Seventeen wells were completed in the Clinton sand, of which 13 were gas wells and 4 were dry holes. The average initial production secured per well drilled, including dry holes, was 1,288,000 cu. ft. The average depth of the Clinton sand was 3000 feet. A gas well was completed in lot 9 of Franklin township, Tuscarawas County. Production was found in the first Clinton sand at a depth of 4354 ft. The initial open flow after shot was 828,000 cu. ft. and the rock

Jan 1, 1937