Search Documents

By R. Armstrong, C. Ware, P. Sudan, G. Whitmore

The northern KwaZulu-Natal (KZN) coastal dune cordon, South Africa, extends from north of Durban into Mozambique. The Quaternary dune cordon, which can be up to 2 km wide, comprises a series of stacked, unconsolidated dunes that in places attain a height of over 100 m. Mining of the dunes produces much of the world’s supply of ilmenite, rutile and zircon. This paper documents the age of zircon grains separated from dune units, identifies likely source rocks and presents an evolutionary history for the dune cordon. Between 30 and 60 detrital zircon grains from three distinct units from the northern KZN coastal dunes were analysed for U/Pb isotopic ages using the SHRIMP II at the Australian National University. The samples represent units from the base (ca. 250 ka; luminescence age1),middle (ca. 190 ka2) and upper (ca. 20 ka2) portions of the coastal dune cordon. Zircon grain ages identify three source populations: (1) a 1 000 to 1 200 Ma group correlated to the Natal Metamorphic Province, (2) a 500 to 650 Ma group representing a Pan-African belt, which may correlate to the Mozambique Belt and (3) a ca. 650 to 800 Ma group of unknown provenance. Surprisingly, the presently exposed basement, comprising the Kaapvaal Craton and Archaean volcano-sedimentary sequences, has not supplied a significant amount of zircon grains (< 5%).This suggests that unroofing of basement rocks in the region has only occurred during the last 20ka. In addition, the absence of zircon grains younger than 500 Ma indicates that the bulk of zirconis not reworked from the Karoo Supergroup cover succession, but may be sourced by reworking of the Natal Group sandstones.

Jan 1, 2003

Like it or not, CPD is upon us. As from 1 January 2006, all registered engineering professionals, i.e. professional engineers, professional engineering technologists, professional certificated engineers and professional engineering technicians, were required to undertake CPD in order to keep their professional registration current. The rules regarding CPD have been gazetted under Government Gazette No. 28328, Board Notice 131 on 23 December 2005, and they also appear on the ECSA website?www.ecsa.co.za. For the convenience of our members they are reproduced in full in this issue of the SAIMM Journal.

Jan 1, 2006

Federal regulations require the use of methane monitors on all mining machines. All machine-mounted methane monitors currently used in underground coal mines rely on catalytic heat of combustion sensors. As a comparison, although not currently approved for use on underground mining equipment, instruments with infrared sensors are evaluated in this study. Potential advantages of using infrared sensors include faster response time, long-term stability, and reduced maintenance needs. Tests conducted in the laboratory and at a full-scale model mine compare the performance of catalytic heat of combustion and infrared sensors operating under test conditions designed to simulate airflow conditions underground.

Jan 1, 2009

As part of the Bureau of Mines program for conserving domestic mineral resources, a survey was made of the methods used for identifying scrap metals. Because of the large number of alloys currently being scrapped, correct identification of these materials is essential if they are to be recycled effectively. The methods and instruments used to identify scrap metals are described and evaluated. These include object recognition, color, density, magnetic testing, spark testing, chemical spot testing, thermoelectric measurements, eddy current measurements, and elemental analysis by chemical and instrumental methods. Other potential techniques are discussed also.

Jan 1, 1982

By J Walshe, G Duclaux, L A. Fisher, R Hough, J S. Cleverley, M F. Gazley

Characterisation of hydrothermal gold systems across multiple scales is increasingly important for our understanding of ore deposit genesis and for targeting new mineralisation. Published work on multiscale mineral system exploration focuses either on applying a single technique across scales or on incorporating a series of techniques across a limited scale range. Typically, these studiesÆ spatial scales vary from crustal to deposit-scale and have successfully linked the distribution and shape of major orebodies to fault systems or varying lithostratigraphy. But, is this scale small enough to answer fundamental questions about the relative timing, processes interactions and mechanisms involved in the formation of ore deposits? We illustrate the potential of a deposit to microscale study, using the Plutonic Gold Mine in Western Australia as an example, to better understand hydrothermal gold systems. Using an integrated approach combining lithological and alteration logs, various geochemical data set, meso- to microscale structural and textural observations and spatial data assimilation, we have revisited the fundamental processes involved in the formation of this significant gold deposit.CITATION:Duclaux, G, Hough, R, Gazley, M F, Fisher, L A, Walshe, J and Cleverley, J S, 2013. A multiscale approach to hydrothermal gold systems - unravelling mineralisation processes at the Plutonic Gold Mine, in Proceedings World Gold 2013 , pp 95-98 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Robert L. Somerville

As more phosphate deposits are discovered and new mines are developed, the necessity of critically evaluating various rocks for phosphoric acid production recurs ever more frequently. This need is accentuated by the increasing number of, fertilizer plants being constructed on deep water at various locations to serve world markets and to take advantage of locally-available sulfur or sulfur-bearing ores. A major proportion of all phosphate rock mined is consumed by wet-process plants and this acid in turn is consumed, usually captively, in the manufacture of fertilizer. It is apparent, therefore, that the first question asked by the developer of a new deposit is - How will it work in a wet-process plant? and conversely, when developing a deep water, project, one of the early studies required is - Which of the available rocks shall we use? What is the correct price to pay? How do we compare one rock with another? The economic importance of even minor aspects of these questions

Jan 1, 1966

By Mingming Zhang

"Three samples received from the EAF shop have been characterized by chemical, X-ray diffraction (XRD), optical microscopy (OM) and scanning electron microscopy (SEM) methods. The objective of this characterization work is to investigate the occurrence of nickel, copper, zinc, sulfur and phosphorus in these samples and identity their origin and associations with iron minerals in the concentrate samples that are from mines.The samples were identified as Mineral, Pellet, and HRD. The latter is the DR! product. All three samples were received as fine powders. The results indicate that, in the mineral sample, magnetite is the major iron oxide mineral with hematite as a second phase based on the OM and XRD studies. Pyrite [FeS2], chalcopyrite [CuFeS2] and bravoite [(Fe,Ni)S2] are major sulfide minerals. Trace amounts of apatite [Ca5(P04)3(F,Cl,OH)], wardite [Na4CaA112(P04)8(OH)8 6H20], giniite [Fe5(P04)4(OH)3 2H20] and vivianite [Fe3(p04)2 8H20] were identified by SEM and XRD. Microscopic studies also indicated that most of the sulfide grains in the mineral sample are present either as liberated fine particles (about 10 microns) or as inclusions within the magnetite and hematite grains. XRD studies revealed magnetite as the major mineral with subordinate amounts of hematite and pyrite confirming the microscopic findings. Copper, nickel, and zinc are mainly present as chalcopyrite, bravoite, and franklinite [(Zn,Mn,Fe)(Fe,Mn)204] in trace amount in the mineral samples, respectively. Impurities carry over to the Pellet and HRD samples.Chemical analyses of the three iron-bearing samples indicate that sulfur and phosphorus in the Pellet sample exceeded the specification. Since liberated pyrite and chalcopyrite particles were observed both in mineral and pellet samples, magnetic and flotation processing routes for this ore should be effective for sulfide removal but at the cost of iron losses. The high phosphorus content of all three samples indicates that there are phosphates which are difficult to remove by the current concentrating process (magnetic separation and flotation)"

Jan 1, 2012

By M. G. Ayat, J. W. Leonard

Introduction Coal preparation plants are continuously losing clean coal in their refuse and contaminating their clean coal product with impurities. This is due to the lack of a system by which the immediate efficiency of the cleaning operation can be determined at any given time. Moreover, the advantage of developing tagging/ tracing techniques would be a reduction in the time and money spent in evaluating the performance of advanced cleaning techniques. Currently, conventional sampling and testing, on-line analyses, and computer information systems are the major tools with which engineers analyze and control the efficiency of processing plants. Conventional sampling and testing is an effective analysis technique but it is slow. On-line analysis provides information on quality parameters rapidly, but these parameters do not provide all of the necessary information. The use of tagged particles in coal preparation plants may provide the necessary link between diagnosis and the application of computers to process control. In this work, a novel technique that uses tagged particles to generate partition data is presented (Leonard et al., 1982). Individually prepared tagged particles are added to the feed and detected in the product or refuse port of specific gravity based processes. Providing that a computer can interpret the output of a detection device and trace particles with predetermined physical properties through the coal preparation plant and that the trace particles actually represent desired raw material, sufficient partition data can be provided for computer analyses and control of processing efficiency. Coal tagging technique The use of tagged particles in coal preparation operations are in the early stages of development. Though there is a brief history of particle tracing in the mineral processing industry (Gardner et al., 1986; Foreman and Amundson, 1976; Poston et al., 1962), the concept has not yet been applied to the analysis and control of processing plant operations. Several methods for tagging coal particles have been identified. These include magnetic, radioactive, and fluorescent techniques. As far as the magnetic tagging of coal particles is concerned, a method has been developed to manufacture synthetic magnetic particles of various sizes and specific gravities. Ideally the synthetic particles would have identical size and density as the coal particles being separated.

Jan 1, 1988

By E. G. Woodruff

Few authors of treatises and papers on engineering subjects hare given adequate attention to topographic maps. The statement applies especially to mining engineering in all branches. Even those who have discussed such maps have treated the subject only in a general way. Therefore it is proposed to outline in this paper a few of the uncommon yet important relationships which topographic maps and their by-product, structure-contour maps, have to modern methods of mining investigation and development when the facts depicted on such maps are properly interpreted. Topography, as suggested by the etymology of the word, means a detailed description of particular places. Written descriptions have been found less effective than the pictorial representations, therefore attempts have been made in various ways to picture the surface features of places. Lines and shading have been used, hachures drawn, and, finally, the contour topographic map. To a large extent this style of map is the result of the demands of engineers. It is designed to meet their needs far more than those of the man untrained in engineering. In fact,. the average man obtains a better idea of the topography of an area from the hachure system than from contour maps. Since the maps have been made chiefly for the use of the engineer, they ought to meet his demands on the one hand, and, on the other, should be used by him to the fullest extent. Such maps, when properly made, accurately portray a portion of the earth&apos;s surface and should present the topography better than a personal examination of the area without a map could present it, because the person making such examination views only a limited portion of the surface at a time, and estimates distances only roughly with his eye. Let the engineer consider carefully the fact that in many instances the topographic map is superior to a personal examination of the surface features of a property because the map is based on careful instrumental measurements, whereas the eye gives imperfect data because it can be used merely for the estimation and

Jan 1, 1914

By J. H. Archibald

"In mines employing cut-and-fill stoping (sand fill), ore passes are built as mining progresses upward. These ore pass raises are generally made from timber and form a vertical ""chimney"", like a very tall log cabin. Traditionally the chimney, or raise, is square in shape and is constructed from square timbers with stepped ends as shown in Figure I. The timbered raise is thus surrounded by sandfill on its outside, leaving the centre open for passing ore down through it. Each layer consists of four timbers and rests flush on the layer below. The corners are frequently pinned or spiked.Under certain conditions in sandfilled stopes large horizontal loads may be transmined to the raise cribbing timbers, or the ""chimney&apos;s"" walls. In deep mines, where rock bursts are a problem, it can be shown that one of the conditions for rockbursts to occur is that the burst zone be stiffer and weaker than the surrounding rock(l). This allows a strain energy build-Up in the rock surrounding the burst zone, and the rate of release of this strain energy is known to be related directly to the over-all strength and stiffness of the rock in the burst zone. In stopes that are sandfilled, attempts are, therefore, usually made to increase the strength of the sandfill by the addition of large-sized waste rock and Portland cement. These measures usually achieve the desired strength of the sandfill and, consequently, the severity and frequency of rockbursts can be reduced.Problems may arise when the now chunky sandfill transmits high loads to the raise cribbing along with relatively large move- merits. This leads to heavily stressed and strained cribbing timbers the Coeur d&apos;Alene district in Idaho, raise cribbing failures are common. A typical mode of cribbing failure is shown in Figure 2. One learns in statics that a structure shaped like the crib in Figure I is inherently unstable , at least from a structural standpoint. The crib has pivoted, in Figure 2, into a rhombi c shape and supports very little load. Soon the four-foot square raise cribbing made from 5 in. by 5 in. timbers will no longer pass ore."

Jan 1, 1991

By R. T. Webber, D. Moffett, D. W. Averill, G. H. Kassakhian

INTRODUCTION In Canada, radium-226 is removed from uranium mining and milling effluents by the addition of barium chloride to precipitate barium-radium sulphate. Large settling ponds are provided to effect solid-liquid separation. However, the barium-radium sulphate precipitate [(Ba,Ra)S04] is a fine, slow-settling crystalline solid which is not easily removed by simple sedimentation systems. Consequently, settling pond effluents may contain appreciable quantities of particulate or suspended radium-226, depending upon the specific pond system and/or the time of year considered. Also, current technology is expected to be incompatible with ultimate disposal goals since safe recovery of the barium-radium sulphate sludge from the settling ponds may be difficult to achieve (IAEA, 1976). Under the auspices of Environment Canada, a Government-Industry Mining Task Force established a Radioactivity Sub-Group in 1974 to assist in the development of effluent regulations and guidelines for the uranium mining industry. Among the recommendations of the Sub-Group was the need to seek more effective methods of radium removal, including development of physical--chemical treatment systems as an alternative to settling ponds. In response to the Sub-Group recommendations, a bench scale feasibility study began in March 1976 at the Wastewater Technology Centre (WTC) of Environment Canada. The bench scale work was expanded and accelerated in 1977 with financial assistance provided by the Atomic Energy Control Board. The results of this study indicated that coagulation and flocculation of the (Ba,Ra)S04 precipitate greatly increased settling rates (Wilkinson and Cohen, 1977). Subsequently, a research program with a larger scope was initiated in January 1978; this program is jointly managed and funded by government and industry as indicated in Table 1. The principal goal of the Joint Government-Industry Program is the development of a physical-chemical process to reduce the radium-226 content of uranium mining and milling effluents. The following effluent radium-226 activities were established as targets for the program: 0.37 Bq/L (10 pCi/L) as total radium-226; 0.11 Bq/L (3 pCi/L) as dissolved radium-226. Process development work was undertaken at bench scale at the WTC and at

Jan 1, 1980

By A Allen, J. A. Garcia

The large increase in the wages of mine workers makes it imperative that all factors tending to limit production per miner be eliminated, if possible. The trolley and storage-battery locomotive, mining machine, hoisting engine, mining system, etc., have increased the possible output per man. But this output is still limited by the capacity of the hoisting engine and cable and by the size of the mine car. The superiority of skip hoisting in metal mining is shown by its almost universal adoption. By varying the size of skip and the rope speed, any desired tonnage can be secured and, since frequently only one kind of material is handled and breakage is unimportant, the loading of the skips can be easily and cheaply effected from bins into which the cars are dumped. The cars may then be designed to fit the conditions in the mine instead of being a compromise between hoisting and mining conditions, very likely suiting neither. In coal mines, the usual practice has been to hoist the car to the surface, either on platform or self-dumping cages. Of late years the number of skip-hoisting plants in coal mines has been rapidly increasing, but there is more or less inertia to overcome in establishing so radical a change in practice; also the earlier skip operations were not uniformly successful. As a result, it became evident that metal-mining practice would require radical modification before skip hoisting could be successfully used in coal mining. Objections to Skip Hoisting Breakage Except where coal is used for coking, or for other purposes whcre breakage is unimportant, breakage of the coal is vitally important all the way from the face to the railroad car. The average selling price is seriously reduced when the percentage of screenings is increased. Following metal-mining practice exactly, the coal would be dumped into a deep pocket, cut off into a skip load by a measuring hopper or other means, dumped into a deep, narrow skip, and dropped into a bin at the top, all of which would contribute to excessive breakage.

Jan 1, 1922

By Metehan Erdogan, Mustafa Serdal Aras, Sedef Cift Karagul, Ishak Karakaya, Esra Karakaya, Merve Kolay Ersoy

Pickling is the treatment of metal surfaces by removing oxide layer, rust, scale, inorganic contaminants or other impurities from ferrous metals, copper or precious metals. A strong inorganic acid such as hydrochloric acid is used for plain carbon or low alloy steel pickling. When the concentration of copper in the pickling solution exceeds about 100 mg/L, reversion may take place and randomly plating of copper onto the steel strips which causes visual incompatibility occur. Furthermore, efficiency of pickling decreases with the increase of copper content. The reversion may be delayed to higher Cu concentrations by adding fresh acid to the line. Increased acid consumption only delays the time to discard the solution but increases the cost and hazardous nature effect on the environment. An experimental electrochemical procedure has been conducted to remove copper from pickling solution to reduce the concentration below 100 mg/L. Within this scope, effects of applied current density, copper concentration and electrolysis duration on copper deposition were studied. Current density was determined as the most effective parameter to remove copper from the regenerated pickling solutions of steel plants.

Mar 1, 2018

Ore samples generally require preparation before analysis. Serious problems can occur with contamination degradation and particle size effects. Both grinding element contammation and sample cross contamination havebeen bound to be related to sample hardness and operator technique. For best results with minerals relevant to the steel industry, the use of Siebtechnik-type mills required a combination of careful planning, short grinding periods and intermediate sieving of the sample. The results may be extended to most mineral, rock, and refractory sample preparabons.

Jan 1, 1978

By J Taylor, L Richards, M McKenzie

When a collapse in its services shaft caused rapid gas build up and its premature closure in. 1951, the Blackwater Mine at Wiauta was in full production with significant ore reserves yet to be mined. A total of nearly 23 tonnes of gold was produced from the mine during its 44 year life. It was New ZealandÆs deepest underground mine, producing gold from an extensive sub-vertical mineralised quartz reef that averaged 0.6 m in width. Mining was by stoping between adits and short shafts, latterly with the main mine access through the 840 m deep Prohibition shaft. Macraes Mining Company Ltd are presently investigating the possibility of reopening the mine. This paper outlines a preliminary assessment of the main geotechnical factors for achieving the reopening, using recent exploration and old mine information. The greywacke host rock mass in the vicinity of the quartz reef has been evaluated using both these sources, and the paper discusses how the geological structure, intact and rock mass strengths, the rock mass defects, in situ stresses, and groundwater inflows may effect the reopening and support of the prohibition shaft, the excavation methods and support for a new supplementary shaft, and the likely excavation and support requirements for working adits and stopes in the rejuvenated mine.

Jan 1, 1996

By A. A. Mular

Examining a typical curriculum for mineral process engineers shows that traditional subjects remain important, namely, engineering, earth and basic sciences, mathematics and mineral proc¬essing technology. However, Table I shows additional subjects that may be woven into a modern curriculum, because of micro- and macro-engineering advances over the years. The ways to incorporate these subjects into the curriculum will vary from school to school. Such changes are in response to evolutionary technological and political needs as determined by society and business. Beginning with the 1950s, engineering empiricism was strengthened through micro-engineering, where fundamentals and mechanism serve as foundations. Scientific apparatus unique to the basic sciences (Zeta meter, FTIR spectroscope) was adapted to test new hypotheses. Coincidentally, as computers became more available, complex differential

Jan 1, 1992

By Jason A. McLennan

Conditional bias is an infamous problem with estimation methods including kriging. Changing estimation parameters will mitigate, but not remove, conditional bias. The conditional bias of kriging is well understood; however, there is widespread confusion in the literature and among practicing geostatisticians regarding the conditional bias of geostatistical simulation. There is no conditional bias of simulation when the simulation results are used correctly. The correct use of simulation for recoverable reserves estimation is to (1) generate multiple realizations conditional to all available data at a small scale, (2) linearly average all realizations to the chosen block size and (3) calculate the probability of each block being ore and the ore grade of each block. The ?probability of ore? and the ?ore grade? are conditionally nonbiased.

May 1, 2002

By P. K. Davis, B. Gharib

The results of a previous basic study of the flow and design characteristics of hydrocyclones demonstrated that a recovery as high as 99% with a product rating* of 0.95 can be achieved on a batch+ basis with a single, water-only cyclone if it is configured properly. The next logical step was to demonstrate continuous processing of gob for the efficient recovery of coal by means of a laboratory-size demonstration system. A project to design and construct such a single-¬cyclone system was sponsored by the US Department of Energy, which also sponsored the initial study. A recovery of 93% with a product rating of 0.89 was demonstrated. The system design and the data taken are discussed.

Jan 1, 1990

By K. Adham, C. T. Harris

Arsenic is often associated with copper, nickel and gold in sulphide deposits. This paper describes a two-stage high-temperature fluid bed reactor for the removal and fixation of As from ores and concentrates. The first (bottom) stage of reactor removes the As through a neutral roast, by volatilization as mostly sulphide species. The second (top) stage of reactor captures the As from the gas phase through oxidative fixation, as a stable iron arsenate, by reaction with an appropriate iron source (sulphide or oxide). The second stage is placed on top of the first, so that their combined function can be achieved in a simple two-stage fluid bed arrangement, with the bottom stage off-gas providing the top stage fluidization.

Jan 1, 2014

By W. J. Carlson, I. Iwasaki

A previous article reported a combination process for recovering both metallic iron and metallic manganese from the manganiferous iron ores of the Cuyuna Range in Minnesota.&apos; In this process, the iron was recovered by direct reduction and magnetic separation and the manganese was recovered from the nonmagnetic tailing by leaching and electrolysis. The current efficiency during the electrolysis of manganese is quite low, in the range of 60 to 70%, due to the simultaneous plating of hydrogen.2,3 The parameters that affect the current efficiency are (1) the concentrations of the manganese ion and the ammonium sulfate buffer, (2) the effect of autoxidant, (3) temperature, (4) pH, and (5) current density. To study the plating characteristics of manganese metal.

Jan 1, 1969